2024-07-08 03:19:40 -03:00
|
|
|
# hw definition file for processing by chibios_pins.py
|
|
|
|
|
# for TAKER F745 BT hardware.
|
|
|
|
|
# thanks to betaflight for pin information
|
|
|
|
|
|
|
|
|
|
# MCU class and specific type
|
|
|
|
|
MCU STM32F7xx STM32F745xx
|
|
|
|
|
|
|
|
|
|
# board ID for firmware load
|
|
|
|
|
APJ_BOARD_ID AP_HW_GEPRCF745BTHD
|
|
|
|
|
|
|
|
|
|
# crystal frequency, setup to use external oscillator
|
|
|
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
|
|
|
|
|
|
FLASH_SIZE_KB 1024
|
|
|
|
|
|
|
|
|
|
# leave 2 sectors free
|
|
|
|
|
FLASH_RESERVE_START_KB 96
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
# only one I2C bus
|
|
|
|
|
I2C_ORDER I2C1
|
|
|
|
|
|
|
|
|
|
# I2C1 for baro
|
|
|
|
|
PB8 I2C1_SCL I2C1
|
|
|
|
|
PB9 I2C1_SDA I2C1
|
|
|
|
|
|
|
|
|
|
# order of UARTs (and USB),
|
|
|
|
|
SERIAL_ORDER OTG1 USART1 USART2 USART3 UART4 EMPTY USART6 UART7 UART8
|
|
|
|
|
|
|
|
|
|
# buzzer
|
|
|
|
|
#define HAL_BUZZER_PIN 80
|
|
|
|
|
|
|
|
|
|
# PA10 IO-debug-console
|
|
|
|
|
PA11 OTG_FS_DM OTG1
|
|
|
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
|
|
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
|
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
|
|
|
|
|
|
# SPI1 for MPU6000
|
|
|
|
|
PA4 MPU6000_CS CS
|
|
|
|
|
PA5 SPI1_SCK SPI1
|
|
|
|
|
PA6 SPI1_MISO SPI1
|
|
|
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
|
|
|
|
|
|
# SPI2 for ICM42688
|
|
|
|
|
PB12 ICM42605_CS CS
|
|
|
|
|
PB13 SPI2_SCK SPI2
|
|
|
|
|
PB14 SPI2_MISO SPI2
|
|
|
|
|
PB15 SPI2_MOSI SPI2
|
|
|
|
|
|
|
|
|
|
# SPI3 for SDCard
|
|
|
|
|
PA15 SDCARD_CS CS
|
|
|
|
|
PC10 SPI3_SCK SPI3
|
|
|
|
|
PC11 SPI3_MISO SPI3
|
|
|
|
|
PC12 SPI3_MOSI SPI3
|
|
|
|
|
|
|
|
|
|
# SPI4 for MAX7456 OSD
|
|
|
|
|
PE4 MAX7456_CS CS
|
|
|
|
|
PE2 SPI4_SCK SPI4
|
|
|
|
|
PE5 SPI4_MISO SPI4
|
|
|
|
|
PE6 SPI4_MOSI SPI4
|
|
|
|
|
|
|
|
|
|
PC3 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
|
|
|
PC2 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
|
|
|
|
|
|
# define default battery setup
|
|
|
|
|
define HAL_BATT_MONITOR_DEFAULT 4
|
|
|
|
|
define HAL_BATT_VOLT_PIN 13
|
|
|
|
|
define HAL_BATT_CURR_PIN 12
|
|
|
|
|
define HAL_BATT_VOLT_SCALE 11.13
|
|
|
|
|
define HAL_BATT_CURR_SCALE 28.5
|
|
|
|
|
|
|
|
|
|
PC13 LED0 OUTPUT LOW GPIO(90) # LED
|
|
|
|
|
define AP_NOTIFY_GPIO_LED_1_ENABLED 1
|
|
|
|
|
define AP_NOTIFY_GPIO_LED_1_PIN 90
|
|
|
|
|
|
|
|
|
|
# In order to accommodate bi-directional dshot certain devices cannot be DMA enabled
|
|
|
|
|
# NODMA indicates these devices, if you remove it they will still not be resolved for DMA
|
|
|
|
|
|
|
|
|
|
# USART1
|
|
|
|
|
PA10 USART1_RX USART1
|
|
|
|
|
PA9 USART1_TX USART1
|
|
|
|
|
define DEFAULT_SERIAL1_PROTOCOL SerialProtocol_MSP_DisplayPort
|
|
|
|
|
|
|
|
|
|
# USART2
|
|
|
|
|
# RC input defaults to UART to allow for bi-dir dshot
|
|
|
|
|
PA2 USART2_TX USART2
|
|
|
|
|
PA3 USART2_RX USART2
|
|
|
|
|
define DEFAULT_SERIAL2_PROTOCOL SerialProtocol_RCIN
|
|
|
|
|
define DEFAULT_SERIAL2_BAUD 115
|
|
|
|
|
|
|
|
|
|
# USART3 (BT)
|
|
|
|
|
PB11 USART3_RX USART3 NODMA
|
|
|
|
|
PB10 USART3_TX USART3 NODMA
|
|
|
|
|
define DEFAULT_SERIAL3_PROTOCOL SerialProtocol_None
|
|
|
|
|
|
|
|
|
|
# UART4 (GPS)
|
|
|
|
|
PA0 UART4_TX UART4 NODMA
|
|
|
|
|
PA1 UART4_RX UART4 NODMA
|
|
|
|
|
define DEFAULT_SERIAL4_PROTOCOL SerialProtocol_GPS
|
|
|
|
|
|
|
|
|
|
# UART6
|
|
|
|
|
PC6 USART6_TX USART6 NODMA
|
|
|
|
|
PC7 USART6_RX USART6 NODMA
|
|
|
|
|
define DEFAULT_SERIAL6_PROTOCOL SerialProtocol_None
|
|
|
|
|
|
|
|
|
|
# UART7
|
|
|
|
|
PE7 UART7_RX UART7 NODMA
|
|
|
|
|
PE8 UART7_TX UART7 NODMA
|
|
|
|
|
define DEFAULT_SERIAL7_PROTOCOL SerialProtocol_None
|
|
|
|
|
|
|
|
|
|
# UART8
|
|
|
|
|
PE0 UART8_RX UART8 NODMA
|
|
|
|
|
PE1 UART8_TX UART8 NODMA
|
|
|
|
|
define DEFAULT_SERIAL8_PROTOCOL SerialProtocol_ESCTelemetry
|
|
|
|
|
|
|
|
|
|
# Motors, bi-directional dshot capable
|
|
|
|
|
PB0 TIM3_CH3 TIM3 PWM(1) GPIO(50) # M1
|
|
|
|
|
PB1 TIM3_CH4 TIM3 PWM(2) GPIO(51) BIDIR # M2
|
|
|
|
|
PB5 TIM3_CH2 TIM3 PWM(3) GPIO(52) # M3
|
|
|
|
|
PB4 TIM3_CH1 TIM3 PWM(4) GPIO(53) BIDIR # M4
|
|
|
|
|
PD12 TIM4_CH1 TIM4 PWM(5) GPIO(54) # M5
|
|
|
|
|
PD13 TIM4_CH2 TIM4 PWM(6) GPIO(55) # M6
|
|
|
|
|
PC8 TIM8_CH3 TIM8 PWM(7) GPIO(56) NODMA # M7
|
|
|
|
|
PC9 TIM8_CH4 TIM8 PWM(8) GPIO(57) NODMA # M8
|
|
|
|
|
|
|
|
|
|
# extra PWM outs
|
|
|
|
|
PA8 TIM1_CH1 TIM1 PWM(9) GPIO(58) # led pin
|
|
|
|
|
PD2 BUZZER OUTPUT GPIO(80) LOW
|
|
|
|
|
define HAL_BUZZER_PIN 80
|
|
|
|
|
define HAL_BUZZER_ON 1
|
|
|
|
|
define HAL_BUZZER_OFF 0
|
|
|
|
|
|
|
|
|
|
DMA_PRIORITY USART2*
|
|
|
|
|
|
|
|
|
|
define HAL_STORAGE_SIZE 16384
|
|
|
|
|
STORAGE_FLASH_PAGE 1
|
|
|
|
|
|
|
|
|
|
# spi devices
|
|
|
|
|
SPIDEV mpu6000 SPI1 DEVID1 MPU6000_CS MODE3 1*MHZ 4*MHZ
|
|
|
|
|
SPIDEV icm42688 SPI2 DEVID1 ICM42605_CS MODE3 2*MHZ 16*MHZ
|
|
|
|
|
SPIDEV sdcard SPI3 DEVID1 SDCARD_CS MODE0 400*KHZ 25*MHZ
|
|
|
|
|
SPIDEV osd SPI4 DEVID4 MAX7456_CS MODE0 10*MHZ 10*MHZ
|
|
|
|
|
|
|
|
|
|
# IMU setup
|
|
|
|
|
IMU Invensensev3 SPI:icm42688 ROTATION_ROLL_180
|
|
|
|
|
IMU Invensense SPI:mpu6000 ROTATION_YAW_90
|
|
|
|
|
define HAL_DEFAULT_INS_FAST_SAMPLE 3
|
|
|
|
|
|
|
|
|
|
# no built-in compass, but probe the i2c bus for all possible
|
|
|
|
|
# external compass types
|
|
|
|
|
define ALLOW_ARM_NO_COMPASS
|
|
|
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
|
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
|
|
|
define HAL_COMPASS_AUTO_ROT_DEFAULT 2
|
|
|
|
|
|
|
|
|
|
# one BARO
|
|
|
|
|
BARO BMP280 I2C:0:0x76
|
|
|
|
|
|
|
|
|
|
define HAL_OS_FATFS_IO 1
|
|
|
|
|
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
|
|
|
|
|
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"
|
|
|
|
|
|
|
|
|
|
# setup for OSD
|
|
|
|
|
define OSD_ENABLED 1
|
|
|
|
|
define HAL_OSD_TYPE_DEFAULT 1
|
|
|
|
|
ROMFS_WILDCARD libraries/AP_OSD/fonts/font0.bin
|
|
|
|
|
|
|
|
|
|
# save some flash
|
|
|
|
|
include ../include/minimize_fpv_osd.inc
|
|
|
|
|
|
2024-09-03 23:36:29 -03:00
|
|
|
|
|
|
|
|
#only enable BMP280 Baro
|
|
|
|
|
define AP_BARO_BACKEND_DEFAULT_ENABLED 0
|
|
|
|
|
undef define AP_BARO_BMP280_ENABLED
|
|
|
|
|
define AP_BARO_BMP280_ENABLED 1
|
|
|
|
|
define AP_BARO_MS56XX_ENABLED 1
|
|
|
|
|
|
|
|
|
|
# need to probe external baros even 'though we're minimised to allow custom build options:
|
2024-07-08 03:19:40 -03:00
|
|
|
undef AP_BARO_PROBE_EXTERNAL_I2C_BUSES
|
|
|
|
|
define AP_BARO_PROBE_EXTERNAL_I2C_BUSES 1
|
