2023-01-17 00:16:23 -04:00
|
|
|
# hw definition file for processing by chibios_hwdef.py
|
|
|
|
|
# for H757
|
|
|
|
|
|
|
|
|
|
# MCU class and specific type
|
|
|
|
|
MCU STM32H7xx STM32H757xx
|
|
|
|
|
|
|
|
|
|
# USB setup
|
|
|
|
|
USB_VENDOR 0x2DAE # ONLY FOR USE BY HEX! NOBODY ELSE
|
|
|
|
|
USB_PRODUCT 0x1059
|
|
|
|
|
USB_STRING_MANUFACTURER "CubePilot"
|
|
|
|
|
USB_STRING_PRODUCT "CubeRed-BL"
|
|
|
|
|
|
|
|
|
|
define CORE_CM7
|
|
|
|
|
define SMPS_PWR
|
|
|
|
|
|
|
|
|
|
# crystal frequency
|
|
|
|
|
OSCILLATOR_HZ 24000000
|
|
|
|
|
|
|
|
|
|
# board ID for firmware load
|
|
|
|
|
APJ_BOARD_ID 1069
|
|
|
|
|
|
|
|
|
|
FLASH_SIZE_KB 2048
|
|
|
|
|
|
|
|
|
|
# bootloader is installed at zero offset
|
|
|
|
|
FLASH_RESERVE_START_KB 0
|
|
|
|
|
|
|
|
|
|
# the location where the bootloader will put the firmware
|
|
|
|
|
# the H743 has 128k sectors
|
|
|
|
|
FLASH_BOOTLOADER_LOAD_KB 128
|
|
|
|
|
|
|
|
|
|
define HAL_LED_ON 0
|
|
|
|
|
|
|
|
|
|
PG5 LED_BOOTLOADER OUTPUT
|
|
|
|
|
|
|
|
|
|
PD5 USART2_TX USART2
|
|
|
|
|
PD6 USART2_RX USART2
|
|
|
|
|
|
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
|
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
|
|
|
|
|
|
PA11 OTG_FS_DM OTG1
|
|
|
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
|
|
2024-06-13 03:58:01 -03:00
|
|
|
# primary <-> secondary
|
|
|
|
|
PE7 UART7_RX UART7
|
|
|
|
|
PE8 UART7_TX UART7
|
|
|
|
|
|
2023-01-17 00:16:23 -04:00
|
|
|
# order of UARTs (and USB)
|
|
|
|
|
SERIAL_ORDER OTG1 USART2
|
|
|
|
|
# USART2 USART6 USART3 UART8 UART7 UART4
|
|
|
|
|
|
|
|
|
|
define STM32_SERIAL_USE_USART2 TRUE
|
2024-06-13 03:58:01 -03:00
|
|
|
define STM32_SERIAL_USE_UART7 TRUE
|
2023-01-17 00:16:23 -04:00
|
|
|
define HAL_USE_SERIAL TRUE
|
|
|
|
|
|
|
|
|
|
define BOOTLOADER_DEBUG SD2
|
2024-06-13 03:58:01 -03:00
|
|
|
define BOOTLOADER_FORWARD_OTG2_SERIAL SD7
|
|
|
|
|
define BOOTLOADER_FORWARD_OTG2_SERIAL_BAUDRATE 2000000
|
|
|
|
|
define BOOTLOADER_FORWARD_OTG2_SERIAL_SWAP TRUE
|
|
|
|
|
define HAL_HAVE_DUAL_USB_CDC 1
|
2023-01-17 00:16:23 -04:00
|
|
|
|
|
|
|
|
# reserve 256 bytes for comms between app and bootloader
|
|
|
|
|
RAM_RESERVE_START 256
|
|
|
|
|
|
|
|
|
|
# QSPI Flash
|
|
|
|
|
PD11 QUADSPI_BK1_IO0 QUADSPI1
|
|
|
|
|
PD12 QUADSPI_BK1_IO1 QUADSPI1
|
|
|
|
|
PE2 QUADSPI_BK1_IO2 QUADSPI1
|
|
|
|
|
PD13 QUADSPI_BK1_IO3 QUADSPI1
|
|
|
|
|
PB10 QUADSPI_BK1_NCS QUADSPI1
|
|
|
|
|
PB2 QUADSPI_CLK QUADSPI1
|
|
|
|
|
|
|
|
|
|
EXT_FLASH_SIZE_MB 32
|
|
|
|
|
INT_FLASH_PRIMARY 1
|
|
|
|
|
|
|
|
|
|
# IFace Device Name Bus QSPI Mode Clk Freq Size (Pow2) NCS Delay
|
|
|
|
|
QSPIDEV w25q-dtr QUADSPI1 MODE1 100*MHZ 31 1
|
|
|
|
|
|
|
|
|
|
# disable peripheral and sensor power in the bootloader
|
|
|
|
|
PG0 VDD_3V3_SENSORS_EN OUTPUT LOW
|
|
|
|
|
PF2 nVDD_5V_PERIPH_EN OUTPUT LOW
|
