mirror of
https://github.com/ArduPilot/ardupilot
synced 2025-01-13 11:28:30 -04:00
101 lines
3.1 KiB
Markdown
101 lines
3.1 KiB
Markdown
|
# iFlight 2RAW H743 Flight Controller
|
||
|
|
|
||
|
|
The iFlight 2RAW H743 is a flight controller produced by [iFlight](https://shop.iflight.com/Thunder-H7-Flight-Controller-Pro2200).
|
||
|
|
|
||
|
|
## Features
|
||
|
|
|
||
|
|
- MCU - STM32H743 32-bit processor running at 480 MHz
|
||
|
|
- IMU - ICM42688P
|
||
|
|
- Barometer - SPL06-001
|
||
|
|
- Onboard Flash: 1GBit (not useable by ArduPilot)
|
||
|
|
- 6x UARTs
|
||
|
|
- 9x PWM Outputs (8 Motor Output, 1 LED)
|
||
|
|
- Battery input voltage: 2S-6S
|
||
|
|
- BEC 5V 1.5A
|
||
|
|
- BEC 10V 1.5A
|
||
|
|
|
||
|
|
## Pinout
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
## UART Mapping
|
||
|
|
|
||
|
|
The UARTs are marked Rn and Tn in the above pinouts. The Rn pin is the
|
||
|
|
receive pin for UARTn. The Tn pin is the transmit pin for UARTn.
|
||
|
|
|
||
|
|
- SERIAL0 -> USB
|
||
|
|
- SERIAL1 -> UART1 (VTX HD, DMA-enabled)
|
||
|
|
- SERIAL2 -> UART2 (RX, DMA-enabled)
|
||
|
|
- SERIAL3 -> UART3 (GPS, DMA-enabled)
|
||
|
|
- SERIAL4 -> UART4 (GPS, DMA-enabled)
|
||
|
|
- SERIAL6 -> UART6 (ESC Telemetry)
|
||
|
|
|
||
|
|
## RC Input
|
||
|
|
|
||
|
|
RC input is configured on the R2 (UART2_RX) pin. It supports all serial RC
|
||
|
|
protocols. For protocols requiring half-duplex serial to transmit
|
||
|
|
telemetry (such as FPort) you should setup SERIAL3 as an RC input serial port,
|
||
|
|
with half-duplex, pin-swap and inversion enabled.
|
||
|
|
|
||
|
|
## FrSky Telemetry
|
||
|
|
|
||
|
|
FrSky Telemetry is supported using the T3 pin (UART3 transmit). You need to set the following parameters to enable support for FrSky S.PORT
|
||
|
|
|
||
|
|
- SERIAL3_PROTOCOL 10
|
||
|
|
- SERIAL3_OPTIONS 7
|
||
|
|
|
||
|
|
## OSD Support
|
||
|
|
|
||
|
|
The iFlight 2RAW H743 supports MSP DisplayPort OSD using OSD_TYPE 5
|
||
|
|
|
||
|
|
## PWM Output
|
||
|
|
|
||
|
|
The iFlight 2RAW H743 supports up to 9 PWM outputs. The pads for motor output
|
||
|
|
M1 to M8 are provided in the motor connector, plus M9 on a separate pad for LED strip
|
||
|
|
or another PWM output.
|
||
|
|
|
||
|
|
The PWM is in 5 groups:
|
||
|
|
|
||
|
|
- PWM 1-2 in group1
|
||
|
|
- PWM 3-6 in group2
|
||
|
|
- PWM 7-8 in group3
|
||
|
|
- PWM 9 in group4
|
||
|
|
|
||
|
|
Channels within the same group need to use the same output rate. If
|
||
|
|
any channel in a group uses DShot then all channels in the group need
|
||
|
|
to use DShot. Channels 1-8 support bi-directional dshot.
|
||
|
|
|
||
|
|
## Battery Monitoring
|
||
|
|
|
||
|
|
The board has a builting voltage and current sensor. The current
|
||
|
|
sensor can read up to 130 Amps. The voltage sensor can handle up to 6S
|
||
|
|
LiPo batteries.
|
||
|
|
|
||
|
|
The correct battery setting parameters are:
|
||
|
|
|
||
|
|
- BATT_MONITOR 4
|
||
|
|
- BATT_VOLT_PIN 11
|
||
|
|
- BATT_CURR_PIN 13
|
||
|
|
- BATT_VOLT_MULT 11.1
|
||
|
|
- BATT_AMP_PERVLT 64
|
||
|
|
|
||
|
|
## Compass
|
||
|
|
|
||
|
|
The iFlight 2RAW H743 does not have a builtin compass, but you can attach an external compass using I2C on the SDA and SCL pads.
|
||
|
|
|
||
|
|
## VTX power control
|
||
|
|
GPIO 81 controls the VTX BEC output to pins marked "10V". Setting this GPIO low removes voltage supply to pins.
|
||
|
|
By default RELAY2 is configured to control this pin and sets the GPIO high.
|
||
|
|
|
||
|
|
## Loading Firmware
|
||
|
|
|
||
|
|
Initial firmware load can be done with DFU by plugging in USB with the
|
||
|
|
bootloader button pressed. Then you should load the "with_bl.hex"
|
||
|
|
firmware, using your favourite DFU loading tool.
|
||
|
|
|
||
|
|
Once the initial firmware is loaded you can update the firmware using
|
||
|
|
any ArduPilot ground station software. Updates should be done with the
|
||
|
|
*.apj firmware files.
|
||
|
|
|