ardupilot/ArduCopterMega/Attitude.pde

void init_pids()
{
	// create limits to how much dampening we'll allow
	// this creates symmetry with the P gain value preventing oscillations
	
	max_stabilize_dampener 	= g.pid_stabilize_roll.kP() * 2500;	// = 0.6 * 2500 = 1500 or 15°	
	max_yaw_dampener		= g.pid_yaw.kP() * 6000;				// = .5 * 6000  = 3000
}


void control_nav_mixer()
{
	// control +- 45° is mixed with the navigation request by the Autopilot
	// output is in degrees = target pitch and roll of copter
	g.rc_1.servo_out = g.rc_1.control_mix(nav_roll);
	g.rc_2.servo_out = g.rc_2.control_mix(nav_pitch);
}

void fbw_nav_mixer()
{
	// control +- 45° is mixed with the navigation request by the Autopilot
	// output is in degrees = target pitch and roll of copter
	g.rc_1.servo_out = nav_roll;
	g.rc_2.servo_out = nav_pitch;
}

void output_stabilize_roll()
{
	float error, rate;
	int dampener;
	
	error 		= g.rc_1.servo_out - dcm.roll_sensor;	
	
	// limit the error we're feeding to the PID
	error 		= constrain(error,  -2500, 2500);

	// write out angles back to servo out - this will be converted to PWM by RC_Channel
	g.rc_1.servo_out 	= g.g.pid_stabilize_roll.get_pid(error,  	delta_ms_fast_loop, 1.0);

	// We adjust the output by the rate of rotation:
	// Rate control through bias corrected gyro rates
	// omega is the raw gyro reading

	// Limit dampening to be equal to propotional term for symmetry
	rate				= degrees(omega.x) * 100.0; 													// 6rad = 34377
	dampener 			= (rate * g.stabilize_dampener);										// 34377 * .175 = 6000
	g.rc_1.servo_out	-= constrain(dampener,  -max_stabilize_dampener, max_stabilize_dampener);	// limit to 1500 based on kP
}

void output_stabilize_pitch()
{
	float error, rate;
	int dampener;
	
	error 	= g.rc_2.servo_out - dcm.pitch_sensor;
	
	// limit the error we're feeding to the PID
	error 	= constrain(error, -2500, 2500);

	// write out angles back to servo out - this will be converted to PWM by RC_Channel
	g.rc_2.servo_out 	= g.pid_stabilize_pitch.get_pid(error, 	delta_ms_fast_loop, 1.0);

	// We adjust the output by the rate of rotation:
	// Rate control through bias corrected gyro rates
	// omega is the raw gyro reading

	// Limit dampening to be equal to propotional term for symmetry
	rate				= degrees(omega.y) * 100.0; 													// 6rad = 34377
	dampener 			= (rate * g.stabilize_dampener);										// 34377 * .175 = 6000
	g.rc_2.servo_out	-= constrain(dampener,  -max_stabilize_dampener, max_stabilize_dampener);	// limit to 1500 based on kP
}

void
clear_yaw_control()
{
	//Serial.print("Clear ");
	rate_yaw_flag  	= false;			// exit rate_yaw_flag
	nav_yaw 		= dcm.yaw_sensor;	// save our Yaw
	yaw_error 		= 0;
}

void output_yaw_with_hold(boolean hold)
{
	if(hold){
		// look to see if we have exited rate control properly - ie stopped turning
		if(rate_yaw_flag){
			// we are still in motion from rate control
			if(fabs(omega.y) < .15){
				clear_yaw_control();
				hold 			= true;			// just to be explicit
			}else{
				// return to rate control until we slow down.
				hold = false;
			}
		}
		
	}else{
		// rate control
		
		// this indicates we are under rate control, when we enter Yaw Hold and 
		// return to 0° per second, we exit rate control and hold the current Yaw		
		rate_yaw_flag 	= true;
		yaw_error 		= 0;
	}
	
	if(hold){
		// try and hold the current nav_yaw setting
		yaw_error		= nav_yaw - dcm.yaw_sensor; 									// +- 60°
		yaw_error 		= wrap_180(yaw_error);

		// limit the error we're feeding to the PID
		yaw_error		= constrain(yaw_error,   -6000, 6000);						// limit error to 60 degees

		// Apply PID and save the new angle back to RC_Channel
		g.rc_4.servo_out 	= g.pid_yaw.get_pid(yaw_error, delta_ms_fast_loop, 1.0); 		// .5 * 6000 = 3000
	
		// We adjust the output by the rate of rotation
		long rate		= degrees(omega.z) * 100.0; 									// 3rad = 17188 , 6rad = 34377
		int dampener 	= ((float)rate * g.hold_yaw_dampener);						// 18000 * .17 = 3000
		
		// Limit dampening to be equal to propotional term for symmetry
		g.rc_4.servo_out	-= constrain(dampener, -max_yaw_dampener, max_yaw_dampener); 	// -3000
	
	}else{		
		// rate control
		long rate		= degrees(omega.z) * 100; 									// 3rad = 17188 , 6rad = 34377
		rate			= constrain(rate, -36000, 36000);							// limit to something fun!
		long error		= ((long)g.rc_4.control_in * 6) - rate;						// control is += 6000 * 6 = 36000
																					// -error = CCW, 	+error = CW
		g.rc_4.servo_out 	= g.pid_acro_rate_yaw.get_pid(error, delta_ms_fast_loop, 1.0); 	// .075 * 36000 = 2700
		g.rc_4.servo_out 	= constrain(g.rc_4.servo_out, -2400, 2400);					// limit to 2400

	}
}



void output_rate_roll()
{
	// rate control
	long rate		= degrees(omega.x) * 100; 									// 3rad = 17188 , 6rad = 34377
	rate			= constrain(rate, -36000, 36000);							// limit to something fun!
	long error		= ((long)g.rc_1.control_in * 8) - rate;						// control is += 4500 * 8 = 36000

	g.rc_1.servo_out 	= g.pid_acro_rate_roll.get_pid(error, delta_ms_fast_loop, 1.0); 	// .075 * 36000 = 2700
	g.rc_1.servo_out 	= constrain(g.rc_1.servo_out, -2400, 2400);					// limit to 2400
}

void output_rate_pitch()
{
	// rate control
	long rate		= degrees(omega.y) * 100; 									// 3rad = 17188 , 6rad = 34377
	rate			= constrain(rate, -36000, 36000);							// limit to something fun!
	long error		= ((long)g.rc_2.control_in * 8) - rate;						// control is += 4500 * 8 = 36000

	g.rc_2.servo_out 	= g.pid_acro_rate_pitch.get_pid(error, delta_ms_fast_loop, 1.0); 	// .075 * 36000 = 2700
	g.rc_2.servo_out 	= constrain(g.rc_2.servo_out, -2400, 2400);					// limit to 2400
}

/*

	g.rc_1.servo_out = g.rc_2.control_in;
	g.rc_2.servo_out = g.rc_2.control_in;
	
	// Rate control through bias corrected gyro rates
	// omega is the raw gyro reading plus Omega_I, so it´s bias corrected
	g.rc_1.servo_out 	-= (omega.x * 5729.57795 * acro_dampener);
	g.rc_2.servo_out 	-= (omega.y * 5729.57795 * acro_dampener);

	//Serial.printf("\trated out %d, omega ", g.rc_1.servo_out);
	//Serial.print((Omega[0] * 5729.57795 * stabilize_rate_roll_pitch), 3);

	// Limit output
	g.rc_1.servo_out  = constrain(g.rc_1.servo_out, -MAX_SERVO_OUTPUT, MAX_SERVO_OUTPUT);
	g.rc_2.servo_out 	= constrain(g.rc_2.servo_out, -MAX_SERVO_OUTPUT, MAX_SERVO_OUTPUT);
	*/
//}


// Zeros out navigation Integrators if we are changing mode, have passed a waypoint, etc.
// Keeps outdated data out of our calculations
void reset_I(void)
{
	g.pid_nav_lat.reset_I();
	g.pid_nav_lon.reset_I();
	g.pid_baro_throttle.reset_I();
	g.pid_sonar_throttle.reset_I();
}