mirror of https://github.com/ArduPilot/ardupilot
64 lines
1.2 KiB
Plaintext
64 lines
1.2 KiB
Plaintext
|
# hw definition file for processing by chibios_hwdef.py
|
||
|
|
# for H743 bootloader
|
||
|
|
|
||
|
|
# MCU class and specific type
|
||
|
|
MCU STM32H7xx STM32H743xx
|
||
|
|
|
||
|
|
# crystal frequency
|
||
|
|
OSCILLATOR_HZ 24000000
|
||
|
|
|
||
|
|
# board ID for firmware load
|
||
|
|
APJ_BOARD_ID 1400
|
||
|
|
|
||
|
|
FLASH_SIZE_KB 2048
|
||
|
|
|
||
|
|
# setup build for a peripheral firmware
|
||
|
|
env AP_PERIPH 1
|
||
|
|
|
||
|
|
# bootloader is installed at zero offset
|
||
|
|
FLASH_RESERVE_START_KB 0
|
||
|
|
|
||
|
|
# the location where the bootloader will put the firmware
|
||
|
|
# the H743 has 128k sectors
|
||
|
|
FLASH_BOOTLOADER_LOAD_KB 128
|
||
|
|
|
||
|
|
define HAL_LED_ON 0
|
||
|
|
|
||
|
|
# order of UARTs (and USB)
|
||
|
|
SERIAL_ORDER OTG1 UART7
|
||
|
|
|
||
|
|
# UART7 maps to uartF in the HAL (serial5 in SERIALn_ parameters).
|
||
|
|
PE7 UART7_RX UART7
|
||
|
|
PE8 UART7_TX UART7
|
||
|
|
|
||
|
|
# Pin for PWM Voltage Selection
|
||
|
|
PB4 PWM_VOLT_SEL OUTPUT HIGH
|
||
|
|
|
||
|
|
PA11 OTG_FS_DM OTG1
|
||
|
|
PA12 OTG_FS_DP OTG1
|
||
|
|
|
||
|
|
PA13 JTMS-SWDIO SWD
|
||
|
|
PA14 JTCK-SWCLK SWD
|
||
|
|
|
||
|
|
# Add CS pins to ensure they are high in bootloader
|
||
|
|
PC1 MAG_CS CS
|
||
|
|
PC2 MPU_CS CS
|
||
|
|
PC13 GYRO_EXT_CS CS
|
||
|
|
PC14 BARO_EXT_CS CS
|
||
|
|
PC15 ACCEL_EXT_CS CS
|
||
|
|
PD7 BARO_CS CS
|
||
|
|
PE4 MPU_EXT_CS CS
|
||
|
|
PD10 FRAM_CS CS SPEED_VERYLOW
|
||
|
|
|
||
|
|
# the first CAN bus
|
||
|
|
PD0 CAN1_RX CAN1
|
||
|
|
PD1 CAN1_TX CAN1
|
||
|
|
|
||
|
|
# This defines the pins for the 2nd CAN interface, if available.
|
||
|
|
PB6 CAN2_TX CAN2
|
||
|
|
PB12 CAN2_RX CAN2
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
define CAN_APP_NODE_NAME "org.ardupilot.CubeOrange-periph"
|