mirror of https://github.com/ArduPilot/ardupilot
87 lines
2.2 KiB
Markdown
87 lines
2.2 KiB
Markdown
|
# ThePeach FCC-K1
|
||
|
|
|
||
|
|
:::warning
|
||
|
|
Ardupilot does not manufacture this (or any) autopilot.
|
||
|
|
Contact the [manufacturer](https://thepeach.kr/) for hardware support or compliance issues.
|
||
|
|
:::
|
||
|
|
|
||
|
|
**ThePeach FCC-K1** is an advanced autopilot designed and manufactured in **ThePeach**.
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
## Specifications
|
||
|
|
|
||
|
|
- Main Processor: STM32F427VIT6
|
||
|
|
- 32bit ARM Cortex-M4, 168 MHz 256 KB RAM 2 MB Flash memory
|
||
|
|
|
||
|
|
- IO Processor: STM32F100C8T6
|
||
|
|
- ARM Cortex-M3, 32bit ARM Cortex-M3, 24 MHz, 8KB SRAM
|
||
|
|
|
||
|
|
- On-board sensors
|
||
|
|
- Accel/Gyro: ICM-20602
|
||
|
|
- Accel/Gyro/Mag: MPU-9250
|
||
|
|
- Barometer: MS5611
|
||
|
|
|
||
|
|
- Interfaces
|
||
|
|
- 8+5 PWM output (8 from IO, 5 from FMU)
|
||
|
|
- Spektrum DSM / DSM2 / DSM-X Satellite compatible input
|
||
|
|
- Futaba S.BUS compatible input and output
|
||
|
|
- PPM sum signal input
|
||
|
|
- Analogue / PWM RSSI input
|
||
|
|
- S.Bus servo output
|
||
|
|
- Safety switch/LED
|
||
|
|
- 4x UART Ports: TELEM1, TELEM2, GPS, SERIAL4
|
||
|
|
- 2x I2C Ports
|
||
|
|
- 1x CAN bus
|
||
|
|
- 1x ADC
|
||
|
|
- Analog inputs for voltage / Current of 1 battery
|
||
|
|
|
||
|
|
- Mechanical
|
||
|
|
- Dimensions: 40.2 x 61.1 x 24.8 mm
|
||
|
|
- Weight: 65g
|
||
|
|
|
||
|
|
## Connectors
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
## Serial Port Mapping
|
||
|
|
|
||
|
|
| UART | Device | Port
|
||
|
|
--- | --- | ---
|
||
|
|
USART1 | /dev/ttyS0 | IO Processor Debug
|
||
|
|
USART2 | /dev/ttyS1 | TELEM1 (flow control)
|
||
|
|
USART3 | /dev/ttyS2 | TELEM2 (flow control)
|
||
|
|
UART4 | /dev/ttyS3 | GPS1
|
||
|
|
USART6 | /dev/ttyS4 | PX4IO
|
||
|
|
UART7 | /dev/ttyS5 | Debug Console
|
||
|
|
UART8 | /dev/ttyS6 | TELEM4
|
||
|
|
|
||
|
|
## Voltage Ratings
|
||
|
|
|
||
|
|
**ThePeach FCC-K1** can be double-redundant on the power supply if two power sources are supplied.
|
||
|
|
The two power rails are: **POWER** and **USB**.
|
||
|
|
|
||
|
|
:::note
|
||
|
|
The output power rails **FMU PWM OUT** and **I/O PWM OUT** do not power the flight controller board (and are not powered by it).
|
||
|
|
You must supply power to one of **POWER** or **USB** or the board will be unpowered.
|
||
|
|
:::
|
||
|
|
|
||
|
|
**Normal Operation Maximum Ratings**
|
||
|
|
|
||
|
|
Under these conditions all power sources will be used in this order to power the system:
|
||
|
|
|
||
|
|
1. POWER input (5V to 5.5V)
|
||
|
|
2. USB input (4.75V to 5.25V)
|
||
|
|
|
||
|
|
**Absolute Maximum Ratings**
|
||
|
|
|
||
|
|
Under these conditions, all power sources cause permanent damage to the flight controller.
|
||
|
|
|
||
|
|
1. POWER input (5.5V Over)
|
||
|
|
2. USB input (5.5V Over)
|
||
|
|
|
||
|
|
## Where to buy
|
||
|
|
|
||
|
|
Order from [ThePeach](http://thepeach.shop/)
|