mirror of https://github.com/ArduPilot/ardupilot
71 lines
1.6 KiB
Plaintext
71 lines
1.6 KiB
Plaintext
|
# hw definition file for processing by chibios_hwdef.py
|
||
|
|
# for bootloader for FMUv4pro hardware (Pixhawk 3 Pro)
|
||
|
|
|
||
|
|
# MCU class and specific type
|
||
|
|
MCU STM32F4xx STM32F469xx
|
||
|
|
|
||
|
|
# board ID for firmware load
|
||
|
|
APJ_BOARD_ID 13
|
||
|
|
|
||
|
|
# crystal frequency
|
||
|
|
OSCILLATOR_HZ 24000000
|
||
|
|
|
||
|
|
# board voltage
|
||
|
|
STM32_VDD 330U
|
||
|
|
|
||
|
|
# ChibiOS system timer
|
||
|
|
STM32_ST_USE_TIMER 5
|
||
|
|
|
||
|
|
# flash size
|
||
|
|
FLASH_SIZE_KB 2048
|
||
|
|
|
||
|
|
# location of application code
|
||
|
|
define FLASH_BOOTLOADER_LOAD_KB 16
|
||
|
|
|
||
|
|
# bootloader loads at start of flash
|
||
|
|
FLASH_RESERVE_START_KB 0
|
||
|
|
|
||
|
|
# uarts and USB to run bootloader protocol on
|
||
|
|
UART_ORDER OTG1 USART2 USART3
|
||
|
|
|
||
|
|
# this is the pin that senses USB being connected. It is an input pin
|
||
|
|
# setup as OPENDRAIN
|
||
|
|
PA9 VBUS INPUT OPENDRAIN
|
||
|
|
|
||
|
|
# now we define the pins that USB is connected on
|
||
|
|
PA11 OTG_FS_DM OTG1
|
||
|
|
PA12 OTG_FS_DP OTG1
|
||
|
|
|
||
|
|
# these are the pins for SWD debugging with a STlinkv2 or black-magic probe
|
||
|
|
PA13 JTMS-SWDIO SWD
|
||
|
|
PA14 JTCK-SWCLK SWD
|
||
|
|
|
||
|
|
# Another USART, this one for telem1
|
||
|
|
PD5 USART2_TX USART2
|
||
|
|
PD6 USART2_RX USART2
|
||
|
|
PD3 USART2_CTS USART2
|
||
|
|
PD4 USART2_RTS USART2
|
||
|
|
|
||
|
|
# the telem2 USART, also with RTS/CTS available
|
||
|
|
# USART3 serial3 telem2
|
||
|
|
PD8 USART3_TX USART3
|
||
|
|
PD9 USART3_RX USART3
|
||
|
|
PD11 USART3_CTS USART3
|
||
|
|
PD12 USART3_RTS USART3
|
||
|
|
|
||
|
|
# define a LED
|
||
|
|
PB1 LED_BOOTLOADER OUTPUT
|
||
|
|
PB11 LED_ACTIVITY OUTPUT
|
||
|
|
define HAL_LED_ON 1
|
||
|
|
|
||
|
|
# we need to tell HAL_ChibiOS/Storage.cpp how much storage is
|
||
|
|
# available (in bytes)
|
||
|
|
define HAL_STORAGE_SIZE 16384
|
||
|
|
|
||
|
|
# uncomment the lines below to enable strict API
|
||
|
|
# checking in ChibiOS
|
||
|
|
# define CH_DBG_ENABLE_ASSERTS TRUE
|
||
|
|
# define CH_DBG_ENABLE_CHECKS TRUE
|
||
|
|
# define CH_DBG_SYSTEM_STATE_CHECK TRUE
|
||
|
|
# define CH_DBG_ENABLE_STACK_CHECK TRUE
|