README ^^^^^^ README for NuttX port to the Embedded Artists' base board with the NXP the LPCXpresso daughter board. Contents ^^^^^^^^ LCPXpresso LPC1768 Board Embedded Artist's Base Board Development Environment GNU Toolchain Options NuttX buildroot Toolchain Code Red IDE LEDs LPCXpresso Configuration Options Configurations LCPXpresso LPC1768 Board ^^^^^^^^^^^^^^^^^^^^^^^^ Pin Description Connector On Board Base Board -------------------------------- --------- -------------- --------------------- P0[0]/RD1/TXD3/SDA1 J6-9 I2C E2PROM SDA TXD3/SDA1 P0[1]/TD1/RXD3/SCL J6-10 RXD3/SCL1 P0[2]/TXD0/AD0[7] J6-21 P0[3]/RXD0/AD0[6] J6-22 P0[4]/I2SRX-CLK/RD2/CAP2.0 J6-38 CAN_RX2 P0[5]/I2SRX-WS/TD2/CAP2.1 J6-39 CAN_TX2 P0[6]/I2SRX_SDA/SSEL1/MAT2[0] J6-8 SSEL1, OLED CS P0[7]/I2STX_CLK/SCK1/MAT2[1] J6-7 SCK1, OLED SCK P0[8]/I2STX_WS/MISO1/MAT2[2] J6-6 MISO1 P0[9]/I2STX_SDA/MOSI1/MAT2[3] J6-5 MOSI1, OLED data in P0[10] J6-40 TXD2/SDA2 P0[11] J6-41 RXD2/SCL2 P0[15]/TXD1/SCK0/SCK J6-13 TXD1/SCK0 P0[16]/RXD1/SSEL0/SSEL J6-14 RXD1/SSEL0 P0[17]/CTS1/MISO0/MISO J6-12 MISO0 P0[18]/DCD1/MOSI0/MOSI J6-11 MOSI0 P0[19]/DSR1/SDA1 PAD17 N/A P0[20]/DTR1/SCL1 PAD18 I2C E2PROM SCL N/A P0[21]/RI1/MCIPWR/RD1 J6-23 P0[22]/RTS1/TD1 J6-24 LED P0[23]/AD0[0]/I2SRX_CLK/CAP3[0] J6-15 AD0.0 P0[24]/AD0[1]/I2SRX_WS/CAP3[1] J6-16 AD0.1 P0[25]/AD0[2]/I2SRX_SDA/TXD3 J6-17 AD0.2 P0[26]/AD0[3]/AOUT/RXD3 J6-18 AD0.3/AOUT / RGB LED P0[27]/SDA0/USB_SDA J6-25 P0[28]/SCL0 J6-26 P0[29]/USB_D+ J6-37 USB_D+ P0[30]/USB_D- J6-36 USB_D- P1[0]/ENET-TXD0 J6-34? TXD0 TX-(Ethernet PHY) P1[1]/ENET_TXD1 J6-35? TXD1 TX+(Ethernet PHY) P1[4]/ENET_TX_EN TXEN N/A P1[8]/ENET_CRS CRS_DV/MODE2 N/A P1[9]/ENET_RXD0 J6-32? RXD0/MODE0 RD-(Ethernet PHY) P1[10]/ENET_RXD1 J6-33? RXD1/MODE1 RD+(Ethernet PHY) P1[14]/ENET_RX_ER RXER/PHYAD0 N/A P1[15]/ENET_REF_CLK REFCLK N/A P1[16]/ENET_MDC MDC N/A P1[17]/ENET_MDIO MDIO N/A P1[18]/USB_UP_LED/PWM1[1]/CAP1[0] PAD1 N/A P1[19]/MC0A/USB_PPWR/N_CAP1.1 PAD2 N/A P1[20]/MCFB0/PWM1.2/SCK0 PAD3 N/A P1[21]/MCABORT/PWM1.3/SSEL0 PAD4 N/A P1[22]/MC0B/USB-PWRD/MAT1.0 PAD5 N/A P1[23]/MCFB1/PWM1.4/MISO0 PAD6 N/A P1[24]/MCFB2/PWM1.5/MOSI0 PAD7 N/A P1[25]/MC1A/MAT1.1 PAD8 N/A P1[26]/MC1B/PWM1.6/CAP0.0 PAD9 N/A P1[27]/CLKOUT/USB-OVRCR-N/CAP0.1 PAD10 N/A P1[28]/MC2A/PCAP1.0/MAT0.0 PAD11 N/A P1[29]/MC2B/PCAP1.1/MAT0.1 PAD12 N/A P1[30]/VBUS/AD0[4] J6-19 AD0.4 P1[31]/SCK1/AD0[5] J6-20 AD0.5 P2[0]/PWM1.1/TXD1 J6-42 PWM1.1 / RGB LED / RS422 RX P2[1]/PWM1.2/RXD1 J6-43 PWM1.2 / OLED voltage / RGB LED P2[2]/PWM1.3/CTS1/TRACEDATA[3] J6-44 PWM1.3 P2[3]/PWM1.4/DCD1/TRACEDATA[2] J6-45 PWM1.4 P2[4]/PWM1.5/DSR1/TRACEDATA[1] J6-46 PWM1.5 P2[5]/PWM1[6]/DTR1/TRACEDATA[0] J6-47 PWM1.6 P2[6]/PCAP1[0]/RI1/TRACECLK J6-48 P2[7]/RD2/RTS1 J6-49 OLED command/data P2[8]/TD2/TXD2 J6-50 P2[9]/USB_CONNECT/RXD2 PAD19 USB Pullup N/A P2[10]/EINT0/NMI J6-51 P2[11]/EINT1/I2STX_CLK J6-52 P2[12]/EINT2/I2STX_WS j6-53 P2[13]/EINT3/I2STX_SDA J6-27 P3[25]/MAT0.0/PWM1.2 PAD13 N/A P3[26]/STCLK/MAT0.1/PWM1.3 PAD14 N/A P4[28]/RX-MCLK/MAT2.0/TXD3 PAD15 N/A P4[29]/TX-MCLK/MAT2.1/RXD3 PAD16 N/A Embedded Artist's Base Board ^^^^^^^^^^^^^^^^^^^^^^^^^^^^ Jumpers ------- There are many jumpers on the base board. A usable combination is the default jumper settings WITH the two J54 jumpers both removed. Those jumpers are for ISP support and will cause the board to reset. To use the SD, J55 must be set to provide chip select PIO1_11 signal as the SD slot chip select. SD Slot ------- Base-board J4/J6 LPC1768 SD Signal Pin Pin --- ----------- ----- -------- CS PIO1_11* 55 P2.2 DIN PIO0_9-MOSI 5 P0.9 MOSI1 DOUT PIO0_8-MISO 6 P0.8 MISO1 CLK PIO2_11-SCK 7 P0.9 SCK1 CD PIO2_10 52 P2.11 These jumper settings are required: *J55 must be set to provide chip select PIO1_11 signal as the SD slot chip select. USB Device ---------- Base-board J4/J6 LPC1768 Signal Pin Pin ------------------- ----- -------- PIO0_6-USB_CONNECT* 23 P0.21 USB_DM 36 USB_D- USB_DP 37 USB_D+ PIO0_3-VBUS_SENSE** 39 P0.5 These jumper settings are listed for information only. They are *not* required for use with NuttX and LPCXpresso. The configurable pins (P0.21 and P0.5) are not used! *J14 must be set to permit GPIO control of the USB connect pin **J12 must be set to permit GPIO control of the USB vbus sense pin J23 is associated the LEDs used for USB support Here is a more detailed pin mapping: ---------------------------------------------+------+----------------------------------------------- LPCXpresso | J4/6 | Base Board ---------------------------------------------| |----------------------------------------------- LPC1768 Signal | | Signal Connection ------------------------------ --------------+------+------------------- --------------------------- P0.29/USB-D+ P0[29]/USB-D+ | 37 | USB_DP USB D+ P0.30/USB-D- P0[30]/USB-D- | 36 | USB_DM USB D- P1.18/USB-UP-LED/PWM1.1/CAP1.0 PAD1 | N/A | N/A N/A P1.30/VBUS/AD0.4 P1[30] | 19 | PIO1_3 (Not used on board) P2.9/USB-CONNECT/RXD2* PAD19 | N/A | N/A N/A ------------------------------ --------------+------+------------------- --------------------------- P0.21/RI1/RD1 P0[21] | 23 | PIO0_6-USB_CONNECT VBUS via J14 and transistor P0.5/I2SRX-WS/TD2/CAP2.1 P0[5] | 39 | PIO0_3-VBUS_SENSE VBUS via J12 ------------------------------ --------------+------+------------------- --------------------------- *P2.9 connects to a transistor driven USB-D+ pullup on the LPCXpresso board. 96x64 White OLED with I2C/SPI interface --------------------------------------- The OLED display can be connected either to the SPI-bus or the I2C-bus. Jumper Settings: - For the SPI interface (default), insert jumpers in J42, J43, J45 pin1-2 and J46 pin 1-2. - For I2C interface, insert jumpers in J45 pin 2-3, J46 pin 2-3 and J47. In either case insert a jumper in J44 in order to allow PIO1_10 to control the OLED-voltage. Jumper Signal Control: J42: Short: SPI Open: I2C (Default: inserted) J44: Allow control of OLED voltage (Default: inserted) PIO1_10-------->J44 ---------->FAN5331 Common Reset: PIO0_0-RESET ---------------> RES# J43: Select OLED chip select J58: For embed (Default: not inserted) PIO0_2--------------->J43 ---->CS# PIO2_7--------->J58 ->J43 ---->D/C# PIO0_8-MISO --------^ J45: Select SPI or I2C clock (Default: SPI clock) PIO2_11-SCK---->J45 ----------> D0 PIO0_4-SCL------------^ J46: Select serial data input (Default: SPI MOSI) PIO0_9-MOSI---->J46 ----------> D1 I2C_SDA---------------^ J47: Allow I2C bi-directional communications (Default: SPI unidirectional) PIO0_5-SDA---->J47 ----------> D2 LPCXpresso Signals ----------------------------+-------+-------------- ---------------------------------------- LPC1758 Pin | J4/6 | Base Board Description ----------------------------+-------+-------------- ---------------------------------------- P2.1/PWM1.2/RXD1 | 43 | PIO1_10 FAN5331 Power Control (SHDN#) RESET_N | 4 | PIO0_0-RESET OLED reset (RES#) -- Resets EVERYTHING P0.6/I2SRX-SDA/SSEL1/MAT2.0 | 8 | PIO0_2 OLED chip select (CS#) P2.7/RD2/RTS1 | 49 | PIO2_7 OLED command/data (D/C#) P0.7/I2STX-CLK/SCK1/MAT2.1 | 7 | PIO2_11-SCK OLED clock (D0) P0.9/I2STX-SDA/MOSI1/MAT2.3 | 5 | PIO0_9-MOSI OLED data in (D1) ----------------------------+-------+-------------- ---------------------------------------- Development Environment ^^^^^^^^^^^^^^^^^^^^^^^ Either Linux or Cygwin on Windows can be used for the development environment. The source has been built only using the GNU toolchain (see below). Other toolchains will likely cause problems. Testing was performed using the Cygwin environment. GNU Toolchain Options ^^^^^^^^^^^^^^^^^^^^^ The NuttX make system has been modified to support the following different toolchain options. 1. The Code Red GNU toolchain 2. The CodeSourcery GNU toolchain, 3. The devkitARM GNU toolchain, 4. The NuttX buildroot Toolchain (see below). All testing has been conducted using the Code Red toolchain and the make system is setup to default to use the Code Red Linux toolchain. To use the other toolchain, you simply need add one of the following configuration options to your .config (or defconfig) file: CONFIG_LPC17_CODESOURCERYW=y : CodeSourcery under Windows CONFIG_LPC17_CODESOURCERYL=y : CodeSourcery under Linux CONFIG_LPC17_DEVKITARM=y : devkitARM under Windows CONFIG_LPC17_BUILDROOT=y : NuttX buildroot under Linux or Cygwin (default) CONFIG_LPC17_CODEREDW=n : Code Red toolchain under Windows CONFIG_LPC17_CODEREDL=y : Code Red toolchain under Linux You may also have to modify the PATH in the setenv.h file if your make cannot find the tools. NOTE: the CodeSourcery (for Windows), devkitARM, and Code Red (for Windoes) are Windows native toolchains. The CodeSourcey (for Linux), Code Red (for Linux) and NuttX buildroot toolchains are Cygwin and/or Linux native toolchains. There are several limitations to using a Windows based toolchain in a Cygwin environment. The three biggest are: 1. The Windows toolchain cannot follow Cygwin paths. Path conversions are performed automatically in the Cygwin makefiles using the 'cygpath' utility but you might easily find some new path problems. If so, check out 'cygpath -w' 2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links are used in Nuttx (e.g., include/arch). The make system works around these problems for the Windows tools by copying directories instead of linking them. But this can also cause some confusion for you: For example, you may edit a file in a "linked" directory and find that your changes had no effect. That is because you are building the copy of the file in the "fake" symbolic directory. If you use a Windows toolchain, you should get in the habit of making like this: make clean_context all An alias in your .bashrc file might make that less painful. 3. Dependencies are not made when using Windows versions of the GCC. This is because the dependencies are generated using Windows pathes which do not work with the Cygwin make. Support has been added for making dependencies with the windows-native toolchains. That support can be enabled by modifying your Make.defs file as follows: - MKDEP = $(TOPDIR)/tools/mknulldeps.sh + MKDEP = $(TOPDIR)/tools/mkdeps.sh --winpaths "$(TOPDIR)" If you have problems with the dependency build (for example, if you are not building on C:), then you may need to modify tools/mkdeps.sh NOTE 1: The CodeSourcery toolchain (2009q1) does not work with default optimization level of -Os (See Make.defs). It will work with -O0, -O1, or -O2, but not with -Os. NOTE 2: The devkitARM toolchain includes a version of MSYS make. Make sure that the paths to Cygwin's /bin and /usr/bin directories appear BEFORE the devkitARM path or will get the wrong version of make. Code Red IDE ^^^^^^^^^^^^ NuttX is built using command-line make. It can be used with an IDE, but some effort will be required to create the project. Makefile Build -------------- Under Linux Eclipse, it is pretty easy to set up an "empty makefile project" and simply use the NuttX makefile to build the system. That is almost for free under Linux. Under Windows, you will need to set up the "Cygwin GCC" empty makefile project in order to work with Windows (Google for "Eclipse Cygwin" - there is a lot of help on the internet). Native Build ------------ Here are a few tips before you start that effort: 1) Select the toolchain that you will be using in your .config file 2) Start the NuttX build at least one time from the Cygwin command line before trying to create your project. This is necessary to create certain auto-generated files and directories that will be needed. 3) Set up include pathes: You will need include/, arch/arm/src/lpc17xx, arch/arm/src/common, arch/arm/src/armv7-m, and sched/. 4) All assembly files need to have the definition option -D __ASSEMBLY__ on the command line. Startup files will probably cause you some headaches. The NuttX startup file is arch/arm/src/lpc17x/lpc17_vectors.S. Using Code Red GNU Tools from Cygwin ------------------------------------ Under Cygwin, the Code Red command line tools (e.g., arm-non-eabi-gcc) cannot be executed because the they only have execut privileges for Administrators. I worked around this by: Opening a native Cygwin RXVT as Administrator (Right click, "Run as administrator"), then executing 'chmod 755 *.exe' in the following directories: /cygdrive/c/nxp/lpcxpreeso_3.6/bin, and /cygdrive/c/nxp/lpcxpreeso_3.6/Tools/bin Command Line Flash Programming ------------------------------ If using LPCLink as your debug connection, first of all boot the LPC-Link using the script: bin\Scripts\bootLPCXpresso type where type = winusb for Windows XP, or type = hid for Windows Vista / 7. Now run the flash programming utility with the following options flash_utility wire -ptarget -flash-load[-exec]=filename [-load-base=base_address] Where flash_utility is one of: crt_emu_lpc11_13 (for LPC11xx or LPC13xx parts) crt_emu_cm3_nxp (for LPC17xx parts) crt_emu_a7_nxp (for LPC21/22/23/24 parts) crt_emu_a9_nxp (for LPC31/32 and LPC29xx parts) crt_emu_cm3_lmi (for TI Stellaris LM3S parts wire is one of: (empty) (for Red Probe+, Red Probe, RDB1768v1, or TI Stellaris evaluation boards) -wire=hid (for RDB1768v2 without upgraded firmware) -wire=winusb (for RDB1768v2 with upgraded firmware) -wire=winusb (for LPC-Link on Windows XP) -wire=hid (for LPC-Link on Windows Vista/ Windows 7) target is the target chip name. For example LPC1343, LPC1114/301, LPC1768 etc. filename is the file to flash program. It may be an executable (axf) or a binary (bin) file. If using a binary file, the base_address must be specified. base_address is the base load address when flash programming a binary file. It should be specified as a hex value with a leading 0x. Note: - flash-load will leave the processor in a stopped state - flash-load-exec will start execution of application as soon as download has completed. Examples To load the executable file app.axf and start it executing on an LPC1758 target using Red Probe, use the following command line: crt_emu_cm3_nxp -pLPC1758 -flash-load-exec=app.axf To load the binary file binary.bin to address 0x1000 to an LPC1343 target using LPC-Link on Windows XP, use the following command line: crt_emu_lpc11_13_nxp -wire=hid -pLPC1343 -flash-load=binary.bin -load-base=0x1000 tools/flash.sh -------------- All of the above steps are automated in the bash script flash.sh that can be found in the configs/lpcxpresso/tools directory. NuttX buildroot Toolchain ^^^^^^^^^^^^^^^^^^^^^^^^^ A GNU GCC-based toolchain is assumed. The files */setenv.sh should be modified to point to the correct path to the Cortex-M3 GCC toolchain (if different from the default in your PATH variable). If you have no Cortex-M3 toolchain, one can be downloaded from the NuttX SourceForge download site (https://sourceforge.net/projects/nuttx/files/). This GNU toolchain builds and executes in the Linux or Cygwin environment. 1. You must have already configured Nuttx in /nuttx. cd tools ./configure.sh lpcxpresso-lpc1768/ 2. Download the latest buildroot package into 3. unpack the buildroot tarball. The resulting directory may have versioning information on it like buildroot-x.y.z. If so, rename /buildroot-x.y.z to /buildroot. 4. cd /buildroot 5. cp configs/cortexm3-defconfig-4.3.3 .config 6. make oldconfig 7. make 8. Edit setenv.h, if necessary, so that the PATH variable includes the path to the newly built binaries. See the file configs/README.txt in the buildroot source tree. That has more detailed PLUS some special instructions that you will need to follow if you are building a Cortex-M3 toolchain for Cygwin under Windows. NOTE: This is an OABI toolchain. NXFLAT Toolchain ^^^^^^^^^^^^^^^^ If you are *not* using the NuttX buildroot toolchain and you want to use the NXFLAT tools, then you will still have to build a portion of the buildroot tools -- just the NXFLAT tools. The buildroot with the NXFLAT tools can be downloaded from the NuttX SourceForge download site (https://sourceforge.net/projects/nuttx/files/). This GNU toolchain builds and executes in the Linux or Cygwin environment. 1. You must have already configured Nuttx in /nuttx. cd tools ./configure.sh lpcxpresso-lpc1768/ 2. Download the latest buildroot package into 3. unpack the buildroot tarball. The resulting directory may have versioning information on it like buildroot-x.y.z. If so, rename /buildroot-x.y.z to /buildroot. 4. cd /buildroot 5. cp configs/cortexm3-defconfig-nxflat .config 6. make oldconfig 7. make 8. Edit setenv.h, if necessary, so that the PATH variable includes the path to the newly builtNXFLAT binaries. LEDs ^^^^ If CONFIG_ARCH_LEDS is defined, then support for the LPCXpresso LEDs will be included in the build. See: - configs/lpcxpresso-lpc1768/include/board.h - Defines LED constants, types and prototypes the LED interface functions. - configs/lpcxpresso-lpc1768/src/lpcxpresso_internal.h - GPIO settings for the LEDs. - configs/lpcxpresso-lpc1768/src/up_leds.c - LED control logic. The LPCXpresso LPC1768 has a single LEDs (there are more on the Embedded Artists base board, but those are not controlled by NuttX). Usage this single LED by NuttX is as follows: - The LED is not illuminated until the LPCXpresso completes initialization. If the LED is stuck in the OFF state, this means that the LPCXpresso did not complete intialization. - Each time the OS enters an interrupt (or a signal) it will turn the LED OFF and restores its previous stated upon return from the interrupt (or signal). The normal state, after initialization will be a dull glow. The brightness of the glow will be inversely related to the proportion of time spent within interrupt handling logic. The glow may decrease in brightness when the system is very busy handling device interrupts and increase in brightness as the system becomes idle. Stuck in the OFF state suggests that that the system never completed initialization; Stuck in the ON state would indicated that the system intialialized, but is not takint interrupts. - If a fatal assertion or a fatal unhandled exception occurs, the LED will flash strongly as a slow, 2Hz rate. LPCXpresso Configuration Options ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ General Architecture Settings: CONFIG_ARCH - Identifies the arch/ subdirectory. This should be set to: CONFIG_ARCH=arm CONFIG_ARCH_family - For use in C code: CONFIG_ARCH_ARM=y CONFIG_ARCH_architecture - For use in C code: CONFIG_ARCH_CORTEXM3=y CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory CONFIG_ARCH_CHIP=lpc17xx CONFIG_ARCH_CHIP_name - For use in C code to identify the exact chip: CONFIG_ARCH_CHIP_LPC1768=y CONFIG_ARCH_BOARD - Identifies the configs subdirectory and hence, the board that supports the particular chip or SoC. CONFIG_ARCH_BOARD=lpcxpresso-lpc1768 CONFIG_ARCH_BOARD_name - For use in C code CONFIG_ARCH_BOARD_LPCEXPRESSO=y CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation of delay loops CONFIG_ENDIAN_BIG - define if big endian (default is little endian) CONFIG_DRAM_SIZE - Describes the installed DRAM (CPU SRAM in this case): CONFIG_DRAM_SIZE=(32*1024) (32Kb) There is an additional 32Kb of SRAM in AHB SRAM banks 0 and 1. CONFIG_DRAM_START - The start address of installed DRAM CONFIG_DRAM_START=0x10000000 CONFIG_ARCH_IRQPRIO - The LPC17xx supports interrupt prioritization CONFIG_ARCH_IRQPRIO=y CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that have LEDs CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt stack. If defined, this symbol is the size of the interrupt stack in bytes. If not defined, the user task stacks will be used during interrupt handling. CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture. CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that cause a 100 second delay during boot-up. This 100 second delay serves no purpose other than it allows you to calibratre CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until the delay actually is 100 seconds. Individual subsystems can be enabled: CONFIG_LPC17_MAINOSC=y CONFIG_LPC17_PLL0=y CONFIG_LPC17_PLL1=n CONFIG_LPC17_ETHERNET=n CONFIG_LPC17_USBHOST=n CONFIG_LPC17_USBOTG=n CONFIG_LPC17_USBDEV=n CONFIG_LPC17_UART0=y CONFIG_LPC17_UART1=n CONFIG_LPC17_UART2=n CONFIG_LPC17_UART3=n CONFIG_LPC17_CAN1=n CONFIG_LPC17_CAN2=n CONFIG_LPC17_SPI=n CONFIG_LPC17_SSP0=n CONFIG_LPC17_SSP1=n CONFIG_LPC17_I2C0=n CONFIG_LPC17_I2C1=n CONFIG_LPC17_I2S=n CONFIG_LPC17_TMR0=n CONFIG_LPC17_TMR1=n CONFIG_LPC17_TMR2=n CONFIG_LPC17_TMR3=n CONFIG_LPC17_RIT=n CONFIG_LPC17_PWM=n CONFIG_LPC17_MCPWM=n CONFIG_LPC17_QEI=n CONFIG_LPC17_RTC=n CONFIG_LPC17_WDT=n CONFIG_LPC17_ADC=n CONFIG_LPC17_DAC=n CONFIG_LPC17_GPDMA=n CONFIG_LPC17_FLASH=n LPC17xx specific device driver settings CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the console and ttys0 (default is the UART0). CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received. This specific the size of the receive buffer CONFIG_UARTn_TXBUFSIZE - Characters are buffered before being sent. This specific the size of the transmit buffer CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8. CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity CONFIG_UARTn_2STOP - Two stop bits LPC17xx specific CAN device driver settings. These settings all require CONFIG_CAN: CONFIG_CAN_EXTID - Enables support for the 29-bit extended ID. Default Standard 11-bit IDs. CONFIG_CAN1_BAUD - CAN1 BAUD rate. Required if CONFIG_LPC17_CAN1 is defined. CONFIG_CAN2_BAUD - CAN1 BAUD rate. Required if CONFIG_LPC17_CAN2 is defined. CONFIG_CAN1_DIVISOR - CAN1 is clocked at CCLK divided by this number. (the CCLK frequency is divided by this number to get the CAN clock). Options = {1,2,4,6}. Default: 4. CONFIG_CAN2_DIVISOR - CAN2 is clocked at CCLK divided by this number. (the CCLK frequency is divided by this number to get the CAN clock). Options = {1,2,4,6}. Default: 4. CONFIG_CAN_TSEG1 - The number of CAN time quanta in segment 1. Default: 6 CONFIG_CAN_TSEG2 = the number of CAN time quanta in segment 2. Default: 7 LPC17xx specific PHY/Ethernet device driver settings. These setting also require CONFIG_NET and CONFIG_LPC17_ETHERNET. CONFIG_PHY_KS8721 - Selects Micrel KS8721 PHY CONFIG_PHY_AUTONEG - Enable auto-negotion CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed. CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex CONFIG_NET_EMACRAM_SIZE - Size of EMAC RAM. Default: 16Kb CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 18 CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 18 CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is the higest priority. CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented). CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs CONFIG_DEBUG. CONFIG_NET_DUMPPACKET - Dump all received and transmitted packets. Also needs CONFIG_DEBUG. CONFIG_NET_HASH - Enable receipt of near-perfect match frames. CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames. Automatically set if CONFIG_NET_IGMP is selected. LPC17xx USB Device Configuration CONFIG_LPC17_USBDEV_FRAME_INTERRUPT Handle USB Start-Of-Frame events. Enable reading SOF from interrupt handler vs. simply reading on demand. Probably a bad idea... Unless there is some issue with sampling the SOF from hardware asynchronously. CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT Enable high priority interrupts. I have no idea why you might want to do that CONFIG_LPC17_USBDEV_NDMADESCRIPTORS Number of DMA descriptors to allocate in SRAM. CONFIG_LPC17_USBDEV_DMA Enable lpc17xx-specific DMA support CONFIG_LPC17_USBDEV_NOVBUS Define if the hardware implementation does not support the VBUS signal CONFIG_LPC17_USBDEV_NOLED Define if the hardware implementation does not support the LED output LPC17xx USB Host Configuration (the LPCXpresso does not support USB Host) CONFIG_USBHOST_OHCIRAM_SIZE Total size of OHCI RAM (in AHB SRAM Bank 1) CONFIG_USBHOST_NEDS Number of endpoint descriptors CONFIG_USBHOST_NTDS Number of transfer descriptors CONFIG_USBHOST_TDBUFFERS Number of transfer descriptor buffers CONFIG_USBHOST_TDBUFSIZE Size of one transfer descriptor buffer CONFIG_USBHOST_IOBUFSIZE Size of one end-user I/O buffer. This can be zero if the application can guarantee that all end-user I/O buffers reside in AHB SRAM. Configurations ^^^^^^^^^^^^^^ Each LPCXpresso configuration is maintained in a sudirectory and can be selected as follow: cd tools ./configure.sh lpcxpresso-lpc1768/ cd - . ./setenv.sh Where is one of the following: dhcpd: This builds the DCHP server using the apps/examples/dhcpd application (for execution from FLASH.) See apps/examples/README.txt for information about the dhcpd example. Jumpers: Nothing special. Use the default base board jumper settings. nsh: Configures the NuttShell (nsh) located at apps/examples/nsh. The Configuration enables both the serial and telnet NSH interfaces. Support for the board's SPI-based MicroSD card is included (but not passing tests as of this writing). NOTE: At present, the value for the SD SPI frequency is too high and the SD will fail. Setting that frequency to 400000 removes the problem. TODO: Tune this frequency to some optimal value. Jumpers: J55 must be set to provide chip select PIO1_11 signal as the SD slot chip select. nx: And example using the NuttX graphics system (NX). This example uses the UG-9664HSWAG01 driver. Jumpers: There are several jumper settings needed by the OLED. All are the default settings: J42: Close to select the SPI interface (Default: closed) J43: Close to support OLED command/data select (Default: closed) J44: Close to allow control of OLED voltage (Default: closed) J45: Close to select SPI clock (Default: closed) J46: Close SPI data input (MOSI) (Default:closed) ostest: This configuration directory, performs a simple OS test using apps/examples/ostest. Jumpers: Nothing special. Use the default base board jumper settings. thttpd: This builds the THTTPD web server example using the THTTPD and the apps/examples/thttpd application. NOTE: You will need to build the NXFLAT toolchain as described above in order to use this example. Jumpers: Nothing special. Use the default base board jumper settings. usbstorage: This configuration directory exercises the USB mass storage class driver at apps/examples/usbstorage. See apps/examples/README.txt for more information. NOTE: At present, the value for the SD SPI frequency is too high and the SD will fail. Setting that frequency to 400000 removes the problem. TODO: Tune this frequency to some optimal value. Jumpers: J55 must be set to provide chip select PIO1_11 signal as the SD slot chip select.