#!nsh
#
# @name 3DR Solo
#
# @type Quadrotor x
# @class Copter
#
# @board px4fmu-v2 exclude
# @board px4fmu-v4 exclude
# @board px4fmu-v4pro exclude
# @board px4fmu-v5 exclude
# @board aerofc-v1 exclude
#
# @maintainer Andreas Antener <andreas@uaventure.com>
#

sh /etc/init.d/rc.mc_defaults

if [ $AUTOCNF == yes ]
then
    # tuning
    param set MC_PITCHRATE_P    0.11
    param set MC_ROLLRATE_P     0.11
    param set MPC_MANTHR_MIN    0.08
    param set MPC_XY_VEL_MAX    3.0
    param set MPC_Z_VEL_MAX_DN     2.0

    # INAV: higher GPS weights for better altitude control
    param set INAV_W_Z_BARO     0.3
    param set INAV_W_Z_GPS_P    0.8
    param set INAV_W_Z_GPS_V    0.8

    # takeoff, land and RTL settings
    param set MIS_TAKEOFF_ALT   4.0
    param set COM_DISARM_LAND   1
    param set RTL_LAND_DELAY    1
    param set RTL_DESCEND_ALT   5.0
    param set RTL_RETURN_ALT    15.0
    param set MPC_TILTMAX_LND   8.0
    param set MPC_LAND_SPEED    0.4
    param set MPC_HOLD_MAX_Z    1.5
    param set MPC_TKO_JMPSPD    2.0
    param set MPC_TKO_SPEED     1.5

    # setup
    # main board rotation: pitch 180
    param set SENS_BOARD_ROT    12
    # solo external mag rotation
    param set CAL_MAG0_ROT      30
    # no safety switch
    param set CBRK_IO_SAFETY    22027
    # battery voltage not available yet
    param set CBRK_SUPPLY_CHK   894281

    # RC configuration
    param set RC_MAP_MODE_SW    5
    param set RC_MAP_PITCH      2
    param set RC_MAP_ROLL       1
    param set RC_MAP_THROTTLE   3
    param set RC_MAP_YAW        4

    param set RC1_DZ            10
    param set RC1_MAX           1988
    param set RC1_MIN           1003
    param set RC1_REV           1
    param set RC1_TRIM          1499
    param set RC2_DZ            10
    param set RC2_MAX           1987
    param set RC2_MIN           1023
    param set RC2_REV           -1
    param set RC2_TRIM          1499
    param set RC3_DZ            10
    param set RC3_MAX           1877
    param set RC3_MIN           1023
    param set RC3_REV           1
    param set RC3_TRIM          1023
    param set RC4_DZ            10
    param set RC4_MAX           1998
    param set RC4_MIN           1012
    param set RC4_REV           1
    param set RC4_TRIM          1500
    param set RC5_DZ            10
    param set RC5_MAX           2000
    param set RC5_MIN           1000
    param set RC5_REV           1
    param set RC5_TRIM          1500
fi

set MIXER quad_x

set PWM_OUT 1234
set MIXER_AUX none

# enable high-speed link on telem 1
set MAVLINK_F "-d /dev/ttyS1 -b 921600 -r 80000 -m onboard -x"