#include "Copter.h" #if MODE_AUTO_ENABLED == ENABLED /* * Init and run calls for auto flight mode * * This file contains the implementation for Land, Waypoint navigation and Takeoff from Auto mode * Command execution code (i.e. command_logic.pde) should: * a) switch to Auto flight mode with set_mode() function. This will cause auto_init to be called * b) call one of the three auto initialisation functions: auto_wp_start(), auto_takeoff_start(), auto_land_start() * c) call one of the verify functions auto_wp_verify(), auto_takeoff_verify, auto_land_verify repeated to check if the command has completed * The main loop (i.e. fast loop) will call update_flight_modes() which will in turn call auto_run() which, based upon the auto_mode variable will call * correct auto_wp_run, auto_takeoff_run or auto_land_run to actually implement the feature */ /* * While in the auto flight mode, navigation or do/now commands can be run. * Code in this file implements the navigation commands */ // auto_init - initialise auto controller bool ModeAuto::init(bool ignore_checks) { auto_RTL = false; if (mission.num_commands() > 1 || ignore_checks) { // reject switching to auto mode if landed with motors armed but first command is not a takeoff (reduce chance of flips) if (motors->armed() && copter.ap.land_complete && !mission.starts_with_takeoff_cmd()) { gcs().send_text(MAV_SEVERITY_CRITICAL, "Auto: Missing Takeoff Cmd"); return false; } _mode = SubMode::LOITER; // stop ROI from carrying over from previous runs of the mission // To-Do: reset the yaw as part of auto_wp_start when the previous command was not a wp command to remove the need for this special ROI check if (auto_yaw.mode() == AUTO_YAW_ROI) { auto_yaw.set_mode(AUTO_YAW_HOLD); } // initialise waypoint and spline controller wp_nav->wp_and_spline_init(); // set flag to start mission waiting_to_start = true; // initialise mission change check (ignore results) IGNORE_RETURN(mis_change_detector.check_for_mission_change()); // clear guided limits copter.mode_guided.limit_clear(); // reset flag indicating if pilot has applied roll or pitch inputs during landing copter.ap.land_repo_active = false; #if PRECISION_LANDING == ENABLED // initialise precland state machine copter.precland_statemachine.init(); #endif return true; } else { return false; } } // stop mission when we leave auto mode void ModeAuto::exit() { if (copter.mode_auto.mission.state() == AP_Mission::MISSION_RUNNING) { copter.mode_auto.mission.stop(); } #if HAL_MOUNT_ENABLED copter.camera_mount.set_mode_to_default(); #endif // HAL_MOUNT_ENABLED auto_RTL = false; } // auto_run - runs the auto controller // should be called at 100hz or more void ModeAuto::run() { // start or update mission if (waiting_to_start) { // don't start the mission until we have an origin Location loc; if (copter.ahrs.get_origin(loc)) { // start/resume the mission (based on MIS_RESTART parameter) mission.start_or_resume(); waiting_to_start = false; // initialise mission change check (ignore results) IGNORE_RETURN(mis_change_detector.check_for_mission_change()); } } else { // check for mission changes if (mis_change_detector.check_for_mission_change()) { // if mission is running restart the current command if it is a waypoint or spline command if ((mission.state() == AP_Mission::MISSION_RUNNING) && (_mode == SubMode::WP)) { if (mission.restart_current_nav_cmd()) { gcs().send_text(MAV_SEVERITY_CRITICAL, "Auto mission changed, restarted command"); } else { // failed to restart mission for some reason gcs().send_text(MAV_SEVERITY_CRITICAL, "Auto mission changed but failed to restart command"); } } } mission.update(); } // call the correct auto controller switch (_mode) { case SubMode::TAKEOFF: takeoff_run(); break; case SubMode::WP: case SubMode::CIRCLE_MOVE_TO_EDGE: wp_run(); break; case SubMode::LAND: land_run(); break; case SubMode::RTL: rtl_run(); break; case SubMode::CIRCLE: circle_run(); break; case SubMode::NAVGUIDED: case SubMode::NAV_SCRIPT_TIME: #if NAV_GUIDED == ENABLED || AP_SCRIPTING_ENABLED nav_guided_run(); #endif break; case SubMode::LOITER: loiter_run(); break; case SubMode::LOITER_TO_ALT: loiter_to_alt_run(); break; case SubMode::NAV_PAYLOAD_PLACE: payload_place_run(); break; case SubMode::NAV_ATTITUDE_TIME: nav_attitude_time_run(); break; } // only pretend to be in auto RTL so long as mission still thinks its in a landing sequence or the mission has completed if (auto_RTL && (!(mission.get_in_landing_sequence_flag() || mission.state() == AP_Mission::mission_state::MISSION_COMPLETE))) { auto_RTL = false; // log exit from Auto RTL copter.logger.Write_Mode((uint8_t)copter.flightmode->mode_number(), ModeReason::AUTO_RTL_EXIT); } } // return true if a position estimate is required bool ModeAuto::requires_GPS() const { // position estimate is required in all sub modes except attitude control return _mode != SubMode::NAV_ATTITUDE_TIME; } // set submode. This may re-trigger the vehicle's EKF failsafe if the new submode requires a position estimate void ModeAuto::set_submode(SubMode new_submode) { // return immediately if the submode has not been changed if (new_submode == _mode) { return; } // backup old mode SubMode old_submode = _mode; // set mode _mode = new_submode; // if changing out of the nav-attitude-time submode, recheck the EKF failsafe // this may trigger a flight mode change if the EKF failsafe is active if (old_submode == SubMode::NAV_ATTITUDE_TIME) { copter.failsafe_ekf_recheck(); } } bool ModeAuto::allows_arming(AP_Arming::Method method) const { return ((copter.g2.auto_options & (uint32_t)Options::AllowArming) != 0) && !auto_RTL; }; // Go straight to landing sequence via DO_LAND_START, if succeeds pretend to be Auto RTL mode bool ModeAuto::jump_to_landing_sequence_auto_RTL(ModeReason reason) { if (mission.jump_to_landing_sequence()) { mission.set_force_resume(true); // if not already in auto switch to auto if ((copter.flightmode == &copter.mode_auto) || set_mode(Mode::Number::AUTO, reason)) { auto_RTL = true; // log entry into AUTO RTL copter.logger.Write_Mode((uint8_t)copter.flightmode->mode_number(), reason); // make happy noise if (copter.ap.initialised) { AP_Notify::events.user_mode_change = 1; } return true; } // mode change failed, revert force resume flag mission.set_force_resume(false); gcs().send_text(MAV_SEVERITY_WARNING, "Mode change to AUTO RTL failed"); } else { gcs().send_text(MAV_SEVERITY_WARNING, "Mode change to AUTO RTL failed: No landing sequence found"); } AP::logger().Write_Error(LogErrorSubsystem::FLIGHT_MODE, LogErrorCode(Number::AUTO_RTL)); // make sad noise if (copter.ap.initialised) { AP_Notify::events.user_mode_change_failed = 1; } return false; } // lua scripts use this to retrieve the contents of the active command bool ModeAuto::nav_script_time(uint16_t &id, uint8_t &cmd, float &arg1, float &arg2) { #if AP_SCRIPTING_ENABLED if (_mode == SubMode::NAV_SCRIPT_TIME) { id = nav_scripting.id; cmd = nav_scripting.command; arg1 = nav_scripting.arg1; arg2 = nav_scripting.arg2; return true; } #endif return false; } // lua scripts use this to indicate when they have complete the command void ModeAuto::nav_script_time_done(uint16_t id) { #if AP_SCRIPTING_ENABLED if ((_mode == SubMode::NAV_SCRIPT_TIME) && (id == nav_scripting.id)) { nav_scripting.done = true; } #endif } // auto_loiter_start - initialises loitering in auto mode // returns success/failure because this can be called by exit_mission bool ModeAuto::loiter_start() { // return failure if GPS is bad if (!copter.position_ok()) { return false; } _mode = SubMode::LOITER; // calculate stopping point Vector3f stopping_point; wp_nav->get_wp_stopping_point(stopping_point); // initialise waypoint controller target to stopping point wp_nav->set_wp_destination(stopping_point); // hold yaw at current heading auto_yaw.set_mode(AUTO_YAW_HOLD); return true; } // auto_rtl_start - initialises RTL in AUTO flight mode void ModeAuto::rtl_start() { // call regular rtl flight mode initialisation and ask it to ignore checks if (copter.mode_rtl.init(true)) { set_submode(SubMode::RTL); } else { // this should never happen because RTL never fails init if argument is true INTERNAL_ERROR(AP_InternalError::error_t::flow_of_control); } } // initialise waypoint controller to implement take-off void ModeAuto::takeoff_start(const Location& dest_loc) { if (!copter.current_loc.initialised()) { // this should never happen because mission commands are not executed until // the AHRS/EKF origin is set by which time current_loc should also have been set INTERNAL_ERROR(AP_InternalError::error_t::flow_of_control); return; } // calculate current and target altitudes // by default current_alt_cm and alt_target_cm are alt-above-EKF-origin int32_t alt_target_cm; bool alt_target_terrain = false; float current_alt_cm = inertial_nav.get_position_z_up_cm(); float terrain_offset; // terrain's altitude in cm above the ekf origin if ((dest_loc.get_alt_frame() == Location::AltFrame::ABOVE_TERRAIN) && wp_nav->get_terrain_offset(terrain_offset)) { // subtract terrain offset to convert vehicle's alt-above-ekf-origin to alt-above-terrain current_alt_cm -= terrain_offset; // specify alt_target_cm as alt-above-terrain alt_target_cm = dest_loc.alt; alt_target_terrain = true; } else { // set horizontal target Location dest(dest_loc); dest.lat = copter.current_loc.lat; dest.lng = copter.current_loc.lng; // get altitude target above EKF origin if (!dest.get_alt_cm(Location::AltFrame::ABOVE_ORIGIN, alt_target_cm)) { // this failure could only happen if take-off alt was specified as an alt-above terrain and we have no terrain data AP::logger().Write_Error(LogErrorSubsystem::TERRAIN, LogErrorCode::MISSING_TERRAIN_DATA); // fall back to altitude above current altitude alt_target_cm = current_alt_cm + dest.alt; } } // sanity check target int32_t alt_target_min_cm = current_alt_cm + (copter.ap.land_complete ? 100 : 0); alt_target_cm = MAX(alt_target_cm, alt_target_min_cm); // initialise yaw auto_yaw.set_mode(AUTO_YAW_HOLD); // clear i term when we're taking off pos_control->init_z_controller(); // initialise alt for WP_NAVALT_MIN and set completion alt auto_takeoff_start(alt_target_cm, alt_target_terrain); // set submode set_submode(SubMode::TAKEOFF); } // auto_wp_start - initialises waypoint controller to implement flying to a particular destination void ModeAuto::wp_start(const Location& dest_loc) { // init wpnav and set origin if transitioning from takeoff if (!wp_nav->is_active()) { Vector3f stopping_point; if (_mode == SubMode::TAKEOFF) { Vector3p takeoff_complete_pos; if (auto_takeoff_get_position(takeoff_complete_pos)) { stopping_point = takeoff_complete_pos.tofloat(); } } wp_nav->wp_and_spline_init(0, stopping_point); } // send target to waypoint controller if (!wp_nav->set_wp_destination_loc(dest_loc)) { // failure to set destination can only be because of missing terrain data copter.failsafe_terrain_on_event(); return; } // initialise yaw // To-Do: reset the yaw only when the previous navigation command is not a WP. this would allow removing the special check for ROI if (auto_yaw.mode() != AUTO_YAW_ROI) { auto_yaw.set_mode_to_default(false); } // set submode set_submode(SubMode::WP); } // auto_land_start - initialises controller to implement a landing void ModeAuto::land_start() { // set horizontal speed and acceleration limits pos_control->set_max_speed_accel_xy(wp_nav->get_default_speed_xy(), wp_nav->get_wp_acceleration()); pos_control->set_correction_speed_accel_xy(wp_nav->get_default_speed_xy(), wp_nav->get_wp_acceleration()); // initialise the vertical position controller if (!pos_control->is_active_xy()) { pos_control->init_xy_controller(); } // set vertical speed and acceleration limits pos_control->set_max_speed_accel_z(wp_nav->get_default_speed_down(), wp_nav->get_default_speed_up(), wp_nav->get_accel_z()); pos_control->set_correction_speed_accel_z(wp_nav->get_default_speed_down(), wp_nav->get_default_speed_up(), wp_nav->get_accel_z()); // initialise the vertical position controller if (!pos_control->is_active_z()) { pos_control->init_z_controller(); } // initialise yaw auto_yaw.set_mode(AUTO_YAW_HOLD); #if LANDING_GEAR_ENABLED == ENABLED // optionally deploy landing gear copter.landinggear.deploy_for_landing(); #endif #if AP_FENCE_ENABLED // disable the fence on landing copter.fence.auto_disable_fence_for_landing(); #endif // reset flag indicating if pilot has applied roll or pitch inputs during landing copter.ap.land_repo_active = false; // this will be set true if prec land is later active copter.ap.prec_land_active = false; // set submode set_submode(SubMode::LAND); } // auto_circle_movetoedge_start - initialise waypoint controller to move to edge of a circle with it's center at the specified location // we assume the caller has performed all required GPS_ok checks void ModeAuto::circle_movetoedge_start(const Location &circle_center, float radius_m) { // set circle center copter.circle_nav->set_center(circle_center); // set circle radius if (!is_zero(radius_m)) { copter.circle_nav->set_radius_cm(radius_m * 100.0f); } // check our distance from edge of circle Vector3f circle_edge_neu; copter.circle_nav->get_closest_point_on_circle(circle_edge_neu); float dist_to_edge = (inertial_nav.get_position_neu_cm() - circle_edge_neu).length(); // if more than 3m then fly to edge if (dist_to_edge > 300.0f) { // convert circle_edge_neu to Location Location circle_edge(circle_edge_neu, Location::AltFrame::ABOVE_ORIGIN); // convert altitude to same as command circle_edge.set_alt_cm(circle_center.alt, circle_center.get_alt_frame()); // initialise wpnav to move to edge of circle if (!wp_nav->set_wp_destination_loc(circle_edge)) { // failure to set destination can only be because of missing terrain data copter.failsafe_terrain_on_event(); } // if we are outside the circle, point at the edge, otherwise hold yaw const float dist_to_center = get_horizontal_distance_cm(inertial_nav.get_position_xy_cm().topostype(), copter.circle_nav->get_center().xy()); // initialise yaw // To-Do: reset the yaw only when the previous navigation command is not a WP. this would allow removing the special check for ROI if (auto_yaw.mode() != AUTO_YAW_ROI) { if (dist_to_center > copter.circle_nav->get_radius() && dist_to_center > 500) { auto_yaw.set_mode_to_default(false); } else { // vehicle is within circle so hold yaw to avoid spinning as we move to edge of circle auto_yaw.set_mode(AUTO_YAW_HOLD); } } // set the submode to move to the edge of the circle set_submode(SubMode::CIRCLE_MOVE_TO_EDGE); } else { circle_start(); } } // auto_circle_start - initialises controller to fly a circle in AUTO flight mode // assumes that circle_nav object has already been initialised with circle center and radius void ModeAuto::circle_start() { // initialise circle controller copter.circle_nav->init(copter.circle_nav->get_center(), copter.circle_nav->center_is_terrain_alt()); if (auto_yaw.mode() != AUTO_YAW_ROI) { auto_yaw.set_mode(AUTO_YAW_CIRCLE); } // set submode to circle set_submode(SubMode::CIRCLE); } #if NAV_GUIDED == ENABLED // auto_nav_guided_start - hand over control to external navigation controller in AUTO mode void ModeAuto::nav_guided_start() { // call regular guided flight mode initialisation if (!copter.mode_guided.init(true)) { // this should never happen because guided mode never fails to init INTERNAL_ERROR(AP_InternalError::error_t::flow_of_control); return; } // initialise guided start time and position as reference for limit checking copter.mode_guided.limit_init_time_and_pos(); // set submode set_submode(SubMode::NAVGUIDED); } #endif //NAV_GUIDED bool ModeAuto::is_landing() const { switch(_mode) { case SubMode::LAND: return true; case SubMode::RTL: return copter.mode_rtl.is_landing(); default: return false; } return false; } bool ModeAuto::is_taking_off() const { return ((_mode == SubMode::TAKEOFF) && !auto_takeoff_complete); } // auto_payload_place_start - initialises controller to implement a placing void ModeAuto::payload_place_start() { nav_payload_place.state = PayloadPlaceStateType_Calibrating_Hover_Start; // set horizontal speed and acceleration limits pos_control->set_max_speed_accel_xy(wp_nav->get_default_speed_xy(), wp_nav->get_wp_acceleration()); pos_control->set_correction_speed_accel_xy(wp_nav->get_default_speed_xy(), wp_nav->get_wp_acceleration()); // initialise the vertical position controller if (!pos_control->is_active_xy()) { pos_control->init_xy_controller(); } // set vertical speed and acceleration limits pos_control->set_max_speed_accel_z(wp_nav->get_default_speed_down(), wp_nav->get_default_speed_up(), wp_nav->get_accel_z()); pos_control->set_correction_speed_accel_z(wp_nav->get_default_speed_down(), wp_nav->get_default_speed_up(), wp_nav->get_accel_z()); // initialise the vertical position controller if (!pos_control->is_active_z()) { pos_control->init_z_controller(); } // initialise yaw auto_yaw.set_mode(AUTO_YAW_HOLD); // set submode set_submode(SubMode::NAV_PAYLOAD_PLACE); } // returns true if pilot's yaw input should be used to adjust vehicle's heading bool ModeAuto::use_pilot_yaw(void) const { return (copter.g2.auto_options.get() & uint32_t(Options::IgnorePilotYaw)) == 0; } bool ModeAuto::set_speed_xy(float speed_xy_cms) { copter.wp_nav->set_speed_xy(speed_xy_cms); return true; } bool ModeAuto::set_speed_up(float speed_up_cms) { copter.wp_nav->set_speed_up(speed_up_cms); return true; } bool ModeAuto::set_speed_down(float speed_down_cms) { copter.wp_nav->set_speed_down(speed_down_cms); return true; } // start_command - this function will be called when the ap_mission lib wishes to start a new command bool ModeAuto::start_command(const AP_Mission::Mission_Command& cmd) { // To-Do: logging when new commands start/end if (copter.should_log(MASK_LOG_CMD)) { copter.logger.Write_Mission_Cmd(mission, cmd); } switch(cmd.id) { /// /// navigation commands /// case MAV_CMD_NAV_VTOL_TAKEOFF: case MAV_CMD_NAV_TAKEOFF: // 22 do_takeoff(cmd); break; case MAV_CMD_NAV_WAYPOINT: // 16 Navigate to Waypoint do_nav_wp(cmd); break; case MAV_CMD_NAV_VTOL_LAND: case MAV_CMD_NAV_LAND: // 21 LAND to Waypoint do_land(cmd); break; case MAV_CMD_NAV_LOITER_UNLIM: // 17 Loiter indefinitely do_loiter_unlimited(cmd); break; case MAV_CMD_NAV_LOITER_TURNS: //18 Loiter N Times do_circle(cmd); break; case MAV_CMD_NAV_LOITER_TIME: // 19 do_loiter_time(cmd); break; case MAV_CMD_NAV_LOITER_TO_ALT: do_loiter_to_alt(cmd); break; case MAV_CMD_NAV_RETURN_TO_LAUNCH: //20 do_RTL(); break; case MAV_CMD_NAV_SPLINE_WAYPOINT: // 82 Navigate to Waypoint using spline do_spline_wp(cmd); break; #if NAV_GUIDED == ENABLED case MAV_CMD_NAV_GUIDED_ENABLE: // 92 accept navigation commands from external nav computer do_nav_guided_enable(cmd); break; #endif case MAV_CMD_NAV_DELAY: // 93 Delay the next navigation command do_nav_delay(cmd); break; case MAV_CMD_NAV_PAYLOAD_PLACE: // 94 place at Waypoint do_payload_place(cmd); break; #if AP_SCRIPTING_ENABLED case MAV_CMD_NAV_SCRIPT_TIME: do_nav_script_time(cmd); break; #endif case MAV_CMD_NAV_ATTITUDE_TIME: do_nav_attitude_time(cmd); break; // // conditional commands // case MAV_CMD_CONDITION_DELAY: // 112 do_wait_delay(cmd); break; case MAV_CMD_CONDITION_DISTANCE: // 114 do_within_distance(cmd); break; case MAV_CMD_CONDITION_YAW: // 115 do_yaw(cmd); break; /// /// do commands /// case MAV_CMD_DO_CHANGE_SPEED: // 178 do_change_speed(cmd); break; case MAV_CMD_DO_SET_HOME: // 179 do_set_home(cmd); break; case MAV_CMD_DO_SET_ROI: // 201 // point the copter and camera at a region of interest (ROI) do_roi(cmd); break; case MAV_CMD_DO_MOUNT_CONTROL: // 205 // point the camera to a specified angle do_mount_control(cmd); break; case MAV_CMD_DO_FENCE_ENABLE: #if AP_FENCE_ENABLED if (cmd.p1 == 0) { //disable copter.fence.enable(false); gcs().send_text(MAV_SEVERITY_INFO, "Fence Disabled"); } else { //enable fence copter.fence.enable(true); gcs().send_text(MAV_SEVERITY_INFO, "Fence Enabled"); } #endif //AP_FENCE_ENABLED break; #if NAV_GUIDED == ENABLED case MAV_CMD_DO_GUIDED_LIMITS: // 220 accept guided mode limits do_guided_limits(cmd); break; #endif #if WINCH_ENABLED == ENABLED case MAV_CMD_DO_WINCH: // Mission command to control winch do_winch(cmd); break; #endif case MAV_CMD_DO_LAND_START: break; default: // unable to use the command, allow the vehicle to try the next command return false; } // always return success return true; } // exit_mission - function that is called once the mission completes void ModeAuto::exit_mission() { // play a tone AP_Notify::events.mission_complete = 1; // if we are not on the ground switch to loiter or land if (!copter.ap.land_complete) { // try to enter loiter but if that fails land if (!loiter_start()) { set_mode(Mode::Number::LAND, ModeReason::MISSION_END); } } else { // if we've landed it's safe to disarm copter.arming.disarm(AP_Arming::Method::MISSIONEXIT); } } // do_guided - start guided mode bool ModeAuto::do_guided(const AP_Mission::Mission_Command& cmd) { // only process guided waypoint if we are in guided mode if (copter.flightmode->mode_number() != Mode::Number::GUIDED && !(copter.flightmode->mode_number() == Mode::Number::AUTO && _mode == SubMode::NAVGUIDED)) { return false; } // switch to handle different commands switch (cmd.id) { case MAV_CMD_NAV_WAYPOINT: { // set wp_nav's destination Location dest(cmd.content.location); return copter.mode_guided.set_destination(dest); } case MAV_CMD_CONDITION_YAW: do_yaw(cmd); return true; default: // reject unrecognised command return false; } return true; } uint32_t ModeAuto::wp_distance() const { switch (_mode) { case SubMode::CIRCLE: return copter.circle_nav->get_distance_to_target(); case SubMode::WP: case SubMode::CIRCLE_MOVE_TO_EDGE: default: return wp_nav->get_wp_distance_to_destination(); } } int32_t ModeAuto::wp_bearing() const { switch (_mode) { case SubMode::CIRCLE: return copter.circle_nav->get_bearing_to_target(); case SubMode::WP: case SubMode::CIRCLE_MOVE_TO_EDGE: default: return wp_nav->get_wp_bearing_to_destination(); } } bool ModeAuto::get_wp(Location& destination) const { switch (_mode) { case SubMode::NAVGUIDED: return copter.mode_guided.get_wp(destination); case SubMode::WP: return wp_nav->get_oa_wp_destination(destination); case SubMode::RTL: return copter.mode_rtl.get_wp(destination); default: return false; } } /******************************************************************************* Verify command Handlers Each type of mission element has a "verify" operation. The verify operation returns true when the mission element has completed and we should move onto the next mission element. Return true if we do not recognize the command so that we move on to the next command *******************************************************************************/ // verify_command - callback function called from ap-mission at 10hz or higher when a command is being run // we double check that the flight mode is AUTO to avoid the possibility of ap-mission triggering actions while we're not in AUTO mode bool ModeAuto::verify_command(const AP_Mission::Mission_Command& cmd) { if (copter.flightmode != &copter.mode_auto) { return false; } bool cmd_complete = false; switch (cmd.id) { // // navigation commands // case MAV_CMD_NAV_VTOL_TAKEOFF: case MAV_CMD_NAV_TAKEOFF: cmd_complete = verify_takeoff(); break; case MAV_CMD_NAV_WAYPOINT: cmd_complete = verify_nav_wp(cmd); break; case MAV_CMD_NAV_VTOL_LAND: case MAV_CMD_NAV_LAND: cmd_complete = verify_land(); break; case MAV_CMD_NAV_PAYLOAD_PLACE: cmd_complete = verify_payload_place(); break; case MAV_CMD_NAV_LOITER_UNLIM: cmd_complete = verify_loiter_unlimited(); break; case MAV_CMD_NAV_LOITER_TURNS: cmd_complete = verify_circle(cmd); break; case MAV_CMD_NAV_LOITER_TIME: cmd_complete = verify_loiter_time(cmd); break; case MAV_CMD_NAV_LOITER_TO_ALT: return verify_loiter_to_alt(); case MAV_CMD_NAV_RETURN_TO_LAUNCH: cmd_complete = verify_RTL(); break; case MAV_CMD_NAV_SPLINE_WAYPOINT: cmd_complete = verify_spline_wp(cmd); break; #if NAV_GUIDED == ENABLED case MAV_CMD_NAV_GUIDED_ENABLE: cmd_complete = verify_nav_guided_enable(cmd); break; #endif case MAV_CMD_NAV_DELAY: cmd_complete = verify_nav_delay(cmd); break; #if AP_SCRIPTING_ENABLED case MAV_CMD_NAV_SCRIPT_TIME: cmd_complete = verify_nav_script_time(); break; #endif case MAV_CMD_NAV_ATTITUDE_TIME: cmd_complete = verify_nav_attitude_time(cmd); break; /// /// conditional commands /// case MAV_CMD_CONDITION_DELAY: cmd_complete = verify_wait_delay(); break; case MAV_CMD_CONDITION_DISTANCE: cmd_complete = verify_within_distance(); break; case MAV_CMD_CONDITION_YAW: cmd_complete = verify_yaw(); break; // do commands (always return true) case MAV_CMD_DO_CHANGE_SPEED: case MAV_CMD_DO_SET_HOME: case MAV_CMD_DO_SET_ROI: case MAV_CMD_DO_MOUNT_CONTROL: case MAV_CMD_DO_GUIDED_LIMITS: case MAV_CMD_DO_FENCE_ENABLE: case MAV_CMD_DO_WINCH: case MAV_CMD_DO_LAND_START: cmd_complete = true; break; default: // error message gcs().send_text(MAV_SEVERITY_WARNING,"Skipping invalid cmd #%i",cmd.id); // return true if we do not recognize the command so that we move on to the next command cmd_complete = true; break; } // send message to GCS if (cmd_complete) { gcs().send_mission_item_reached_message(cmd.index); } return cmd_complete; } // takeoff_run - takeoff in auto mode // called by auto_run at 100hz or more void ModeAuto::takeoff_run() { // if the user doesn't want to raise the throttle we can set it automatically // note that this can defeat the disarm check on takeoff if ((copter.g2.auto_options & (int32_t)Options::AllowTakeOffWithoutRaisingThrottle) != 0) { copter.set_auto_armed(true); } auto_takeoff_run(); } // auto_wp_run - runs the auto waypoint controller // called by auto_run at 100hz or more void ModeAuto::wp_run() { // process pilot's yaw input float target_yaw_rate = 0; if (!copter.failsafe.radio && use_pilot_yaw()) { // get pilot's desired yaw rate target_yaw_rate = get_pilot_desired_yaw_rate(channel_yaw->norm_input_dz()); if (!is_zero(target_yaw_rate)) { auto_yaw.set_mode(AUTO_YAW_HOLD); } } // if not armed set throttle to zero and exit immediately if (is_disarmed_or_landed()) { make_safe_ground_handling(); return; } // set motors to full range motors->set_desired_spool_state(AP_Motors::DesiredSpoolState::THROTTLE_UNLIMITED); // run waypoint controller copter.failsafe_terrain_set_status(wp_nav->update_wpnav()); // WP_Nav has set the vertical position control targets // run the vertical position controller and set output throttle pos_control->update_z_controller(); // call attitude controller if (auto_yaw.mode() == AUTO_YAW_HOLD) { // roll & pitch from waypoint controller, yaw rate from pilot attitude_control->input_thrust_vector_rate_heading(wp_nav->get_thrust_vector(), target_yaw_rate); } else { // roll, pitch from waypoint controller, yaw heading from auto_heading() attitude_control->input_thrust_vector_heading(wp_nav->get_thrust_vector(), auto_yaw.yaw(), auto_yaw.rate_cds()); } } // auto_land_run - lands in auto mode // called by auto_run at 100hz or more void ModeAuto::land_run() { // if not armed set throttle to zero and exit immediately if (is_disarmed_or_landed()) { make_safe_ground_handling(); return; } // set motors to full range motors->set_desired_spool_state(AP_Motors::DesiredSpoolState::THROTTLE_UNLIMITED); // run normal landing or precision landing (if enabled) land_run_normal_or_precland(); } // auto_rtl_run - rtl in AUTO flight mode // called by auto_run at 100hz or more void ModeAuto::rtl_run() { // call regular rtl flight mode run function copter.mode_rtl.run(false); } // auto_circle_run - circle in AUTO flight mode // called by auto_run at 100hz or more void ModeAuto::circle_run() { // process pilot's yaw input float target_yaw_rate = 0; if (!copter.failsafe.radio && use_pilot_yaw()) { // get pilot's desired yaw rate target_yaw_rate = get_pilot_desired_yaw_rate(channel_yaw->norm_input_dz()); if (!is_zero(target_yaw_rate)) { auto_yaw.set_mode(AUTO_YAW_HOLD); } } // call circle controller copter.failsafe_terrain_set_status(copter.circle_nav->update()); // WP_Nav has set the vertical position control targets // run the vertical position controller and set output throttle pos_control->update_z_controller(); if (auto_yaw.mode() == AUTO_YAW_HOLD) { // roll & pitch from waypoint controller, yaw rate from pilot attitude_control->input_thrust_vector_rate_heading(copter.circle_nav->get_thrust_vector(), target_yaw_rate); } else { // roll, pitch from waypoint controller, yaw heading from auto_heading() attitude_control->input_thrust_vector_heading(copter.circle_nav->get_thrust_vector(), auto_yaw.yaw()); } } #if NAV_GUIDED == ENABLED || AP_SCRIPTING_ENABLED // auto_nav_guided_run - allows control by external navigation controller // called by auto_run at 100hz or more void ModeAuto::nav_guided_run() { // call regular guided flight mode run function copter.mode_guided.run(); } #endif // NAV_GUIDED || AP_SCRIPTING_ENABLED // auto_loiter_run - loiter in AUTO flight mode // called by auto_run at 100hz or more void ModeAuto::loiter_run() { // if not armed set throttle to zero and exit immediately if (is_disarmed_or_landed()) { make_safe_ground_handling(); return; } // accept pilot input of yaw float target_yaw_rate = 0; if (!copter.failsafe.radio && use_pilot_yaw()) { target_yaw_rate = get_pilot_desired_yaw_rate(channel_yaw->norm_input_dz()); } // set motors to full range motors->set_desired_spool_state(AP_Motors::DesiredSpoolState::THROTTLE_UNLIMITED); // run waypoint and z-axis position controller copter.failsafe_terrain_set_status(wp_nav->update_wpnav()); pos_control->update_z_controller(); attitude_control->input_thrust_vector_rate_heading(wp_nav->get_thrust_vector(), target_yaw_rate); } // auto_loiter_run - loiter to altitude in AUTO flight mode // called by auto_run at 100hz or more void ModeAuto::loiter_to_alt_run() { // if not auto armed or motor interlock not enabled set throttle to zero and exit immediately if (is_disarmed_or_landed() || !motors->get_interlock()) { make_safe_ground_handling(); return; } // possibly just run the waypoint controller: if (!loiter_to_alt.reached_destination_xy) { loiter_to_alt.reached_destination_xy = wp_nav->reached_wp_destination_xy(); if (!loiter_to_alt.reached_destination_xy) { wp_run(); return; } } if (!loiter_to_alt.loiter_start_done) { // set horizontal speed and acceleration limits pos_control->set_max_speed_accel_xy(wp_nav->get_default_speed_xy(), wp_nav->get_wp_acceleration()); pos_control->set_correction_speed_accel_xy(wp_nav->get_default_speed_xy(), wp_nav->get_wp_acceleration()); if (!pos_control->is_active_xy()) { pos_control->init_xy_controller(); } loiter_to_alt.loiter_start_done = true; } const float alt_error_cm = copter.current_loc.alt - loiter_to_alt.alt; if (fabsf(alt_error_cm) < 5.0) { // random numbers R US loiter_to_alt.reached_alt = true; } else if (alt_error_cm * loiter_to_alt.alt_error_cm < 0) { // we were above and are now below, or vice-versa loiter_to_alt.reached_alt = true; } loiter_to_alt.alt_error_cm = alt_error_cm; // loiter... land_run_horizontal_control(); // Compute a vertical velocity demand such that the vehicle // approaches the desired altitude. float target_climb_rate = sqrt_controller( -alt_error_cm, pos_control->get_pos_z_p().kP(), pos_control->get_max_accel_z_cmss(), G_Dt); target_climb_rate = constrain_float(target_climb_rate, pos_control->get_max_speed_down_cms(), pos_control->get_max_speed_up_cms()); // get avoidance adjusted climb rate target_climb_rate = get_avoidance_adjusted_climbrate(target_climb_rate); // update the vertical offset based on the surface measurement copter.surface_tracking.update_surface_offset(); // Send the commanded climb rate to the position controller pos_control->set_pos_target_z_from_climb_rate_cm(target_climb_rate); pos_control->update_z_controller(); } // maintain an attitude for a specified time void ModeAuto::nav_attitude_time_run() { // if not auto armed or motor interlock not enabled set throttle to zero and exit immediately if (is_disarmed_or_landed() || !motors->get_interlock()) { make_safe_ground_handling(); return; } // constrain climb rate float target_climb_rate_cms = constrain_float(nav_attitude_time.climb_rate * 100.0, pos_control->get_max_speed_down_cms(), pos_control->get_max_speed_up_cms()); // get avoidance adjusted climb rate target_climb_rate_cms = get_avoidance_adjusted_climbrate(target_climb_rate_cms); // limit and scale lean angles const float angle_limit_cd = MAX(1000.0f, MIN(copter.aparm.angle_max, attitude_control->get_althold_lean_angle_max_cd())); Vector2f target_rp_cd(nav_attitude_time.roll_deg * 100, nav_attitude_time.pitch_deg * 100); target_rp_cd.limit_length(angle_limit_cd); // send targets to attitude controller attitude_control->input_euler_angle_roll_pitch_yaw(target_rp_cd.x, target_rp_cd.y, nav_attitude_time.yaw_deg * 100, true); // Send the commanded climb rate to the position controller pos_control->set_pos_target_z_from_climb_rate_cm(target_climb_rate_cms); pos_control->update_z_controller(); } // auto_payload_place_run - places an object in auto mode // called by auto_run at 100hz or more void ModeAuto::payload_place_run() { if (!payload_place_run_should_run()) { zero_throttle_and_relax_ac(); return; } // set motors to full range motors->set_desired_spool_state(AP_Motors::DesiredSpoolState::THROTTLE_UNLIMITED); switch (nav_payload_place.state) { case PayloadPlaceStateType_FlyToLocation: return wp_run(); case PayloadPlaceStateType_Calibrating_Hover_Start: case PayloadPlaceStateType_Calibrating_Hover: return payload_place_run_hover(); case PayloadPlaceStateType_Descending_Start: case PayloadPlaceStateType_Descending: return payload_place_run_descend(); case PayloadPlaceStateType_Releasing_Start: case PayloadPlaceStateType_Releasing: case PayloadPlaceStateType_Released: case PayloadPlaceStateType_Ascending_Start: return payload_place_run_hover(); case PayloadPlaceStateType_Ascending: case PayloadPlaceStateType_Done: return takeoff_run(); } } bool ModeAuto::payload_place_run_should_run() { // must be armed if (!motors->armed()) { return false; } // must be auto-armed if (!copter.ap.auto_armed) { return false; } // must not be landed if (copter.ap.land_complete && (nav_payload_place.state == PayloadPlaceStateType_FlyToLocation || nav_payload_place.state == PayloadPlaceStateType_Calibrating_Hover_Start)) { return false; } // interlock must be enabled (i.e. unsafe) if (!motors->get_interlock()) { return false; } return true; } void ModeAuto::payload_place_run_hover() { land_run_horizontal_control(); land_run_vertical_control(true); } void ModeAuto::payload_place_run_descend() { land_run_horizontal_control(); land_run_vertical_control(); } // sets the target_loc's alt to the vehicle's current alt but does not change target_loc's frame // in the case of terrain altitudes either the terrain database or the rangefinder may be used // returns true on success, false on failure bool ModeAuto::shift_alt_to_current_alt(Location& target_loc) const { // if terrain alt using rangefinder is being used then set alt to current rangefinder altitude if ((target_loc.get_alt_frame() == Location::AltFrame::ABOVE_TERRAIN) && (wp_nav->get_terrain_source() == AC_WPNav::TerrainSource::TERRAIN_FROM_RANGEFINDER)) { int32_t curr_rngfnd_alt_cm; if (copter.get_rangefinder_height_interpolated_cm(curr_rngfnd_alt_cm)) { // wp_nav is using rangefinder so use current rangefinder alt target_loc.set_alt_cm(MAX(curr_rngfnd_alt_cm, 200), Location::AltFrame::ABOVE_TERRAIN); return true; } return false; } // take copy of current location and change frame to match target Location currloc = copter.current_loc; if (!currloc.change_alt_frame(target_loc.get_alt_frame())) { // this could fail due missing terrain database alt return false; } // set target_loc's alt target_loc.set_alt_cm(currloc.alt, currloc.get_alt_frame()); return true; } /********************************************************************************/ // Nav (Must) commands /********************************************************************************/ // do_takeoff - initiate takeoff navigation command void ModeAuto::do_takeoff(const AP_Mission::Mission_Command& cmd) { // Set wp navigation target to safe altitude above current position takeoff_start(cmd.content.location); } Location ModeAuto::loc_from_cmd(const AP_Mission::Mission_Command& cmd, const Location& default_loc) const { Location ret(cmd.content.location); // use current lat, lon if zero if (ret.lat == 0 && ret.lng == 0) { ret.lat = default_loc.lat; ret.lng = default_loc.lng; } // use default altitude if not provided in cmd if (ret.alt == 0) { // set to default_loc's altitude but in command's alt frame // note that this may use the terrain database int32_t default_alt; if (default_loc.get_alt_cm(ret.get_alt_frame(), default_alt)) { ret.set_alt_cm(default_alt, ret.get_alt_frame()); } else { // default to default_loc's altitude and frame ret.set_alt_cm(default_loc.alt, default_loc.get_alt_frame()); } } return ret; } // do_nav_wp - initiate move to next waypoint void ModeAuto::do_nav_wp(const AP_Mission::Mission_Command& cmd) { // calculate default location used when lat, lon or alt is zero Location default_loc = copter.current_loc; if (wp_nav->is_active() && wp_nav->reached_wp_destination()) { if (!wp_nav->get_wp_destination_loc(default_loc)) { // this should never happen INTERNAL_ERROR(AP_InternalError::error_t::flow_of_control); } } // init wpnav and set origin if transitioning from takeoff if (!wp_nav->is_active()) { Vector3f stopping_point; if (_mode == SubMode::TAKEOFF) { Vector3p takeoff_complete_pos; if (auto_takeoff_get_position(takeoff_complete_pos)) { stopping_point = takeoff_complete_pos.tofloat(); } } wp_nav->wp_and_spline_init(0, stopping_point); } // get waypoint's location from command and send to wp_nav const Location dest_loc = loc_from_cmd(cmd, default_loc); if (!wp_nav->set_wp_destination_loc(dest_loc)) { // failure to set destination can only be because of missing terrain data copter.failsafe_terrain_on_event(); return; } // this will be used to remember the time in millis after we reach or pass the WP. loiter_time = 0; // this is the delay, stored in seconds loiter_time_max = cmd.p1; // set next destination if necessary if (!set_next_wp(cmd, dest_loc)) { // failure to set next destination can only be because of missing terrain data copter.failsafe_terrain_on_event(); return; } // initialise yaw // To-Do: reset the yaw only when the previous navigation command is not a WP. this would allow removing the special check for ROI if (auto_yaw.mode() != AUTO_YAW_ROI) { auto_yaw.set_mode_to_default(false); } // set submode set_submode(SubMode::WP); } // checks the next mission command and adds it as a destination if necessary // supports both straight line and spline waypoints // cmd should be the current command // default_loc should be the destination from the current_cmd but corrected for cases where user set lat, lon or alt to zero // returns true on success, false on failure which should only happen due to a failure to retrieve terrain data bool ModeAuto::set_next_wp(const AP_Mission::Mission_Command& current_cmd, const Location &default_loc) { // do not add next wp if current command has a delay meaning the vehicle will stop at the destination if (current_cmd.p1 > 0) { return true; } // do not add next wp if there are no more navigation commands AP_Mission::Mission_Command next_cmd; if (!mission.get_next_nav_cmd(current_cmd.index+1, next_cmd)) { return true; } // whether vehicle should stop at the target position depends upon the next command switch (next_cmd.id) { case MAV_CMD_NAV_WAYPOINT: case MAV_CMD_NAV_LOITER_UNLIM: case MAV_CMD_NAV_LOITER_TIME: { const Location dest_loc = loc_from_cmd(current_cmd, default_loc); const Location next_dest_loc = loc_from_cmd(next_cmd, dest_loc); return wp_nav->set_wp_destination_next_loc(next_dest_loc); } case MAV_CMD_NAV_SPLINE_WAYPOINT: { // get spline's location and next location from command and send to wp_nav Location next_dest_loc, next_next_dest_loc; bool next_next_dest_loc_is_spline; get_spline_from_cmd(next_cmd, default_loc, next_dest_loc, next_next_dest_loc, next_next_dest_loc_is_spline); return wp_nav->set_spline_destination_next_loc(next_dest_loc, next_next_dest_loc, next_next_dest_loc_is_spline); } case MAV_CMD_NAV_VTOL_LAND: case MAV_CMD_NAV_LAND: // stop because we may change between rel,abs and terrain alt types case MAV_CMD_NAV_LOITER_TURNS: case MAV_CMD_NAV_RETURN_TO_LAUNCH: case MAV_CMD_NAV_VTOL_TAKEOFF: case MAV_CMD_NAV_TAKEOFF: // always stop for RTL and takeoff commands default: // for unsupported commands it is safer to stop break; } return true; } // do_land - initiate landing procedure void ModeAuto::do_land(const AP_Mission::Mission_Command& cmd) { // To-Do: check if we have already landed // if location provided we fly to that location at current altitude if (cmd.content.location.lat != 0 || cmd.content.location.lng != 0) { // set state to fly to location state = State::FlyToLocation; // convert cmd to location class Location target_loc(cmd.content.location); if (!shift_alt_to_current_alt(target_loc)) { // this can only fail due to missing terrain database alt or rangefinder alt // use current alt-above-home and report error target_loc.set_alt_cm(copter.current_loc.alt, Location::AltFrame::ABOVE_HOME); AP::logger().Write_Error(LogErrorSubsystem::TERRAIN, LogErrorCode::MISSING_TERRAIN_DATA); gcs().send_text(MAV_SEVERITY_CRITICAL, "Land: no terrain data, using alt-above-home"); } wp_start(target_loc); } else { // set landing state state = State::Descending; // initialise landing controller land_start(); } } // do_loiter_unlimited - start loitering with no end conditions // note: caller should set yaw_mode void ModeAuto::do_loiter_unlimited(const AP_Mission::Mission_Command& cmd) { // convert back to location Location target_loc(cmd.content.location); // use current location if not provided if (target_loc.lat == 0 && target_loc.lng == 0) { // To-Do: make this simpler Vector3f temp_pos; copter.wp_nav->get_wp_stopping_point_xy(temp_pos.xy()); const Location temp_loc(temp_pos, Location::AltFrame::ABOVE_ORIGIN); target_loc.lat = temp_loc.lat; target_loc.lng = temp_loc.lng; } // use current altitude if not provided // To-Do: use z-axis stopping point instead of current alt if (target_loc.alt == 0) { // set to current altitude but in command's alt frame int32_t curr_alt; if (copter.current_loc.get_alt_cm(target_loc.get_alt_frame(),curr_alt)) { target_loc.set_alt_cm(curr_alt, target_loc.get_alt_frame()); } else { // default to current altitude as alt-above-home target_loc.set_alt_cm(copter.current_loc.alt, copter.current_loc.get_alt_frame()); } } // start way point navigator and provide it the desired location wp_start(target_loc); } // do_circle - initiate moving in a circle void ModeAuto::do_circle(const AP_Mission::Mission_Command& cmd) { const Location circle_center = loc_from_cmd(cmd, copter.current_loc); // calculate radius uint16_t circle_radius_m = HIGHBYTE(cmd.p1); // circle radius held in high byte of p1 if (cmd.id == MAV_CMD_NAV_LOITER_TURNS && cmd.type_specific_bits & (1U << 0)) { // special storage handling allows for larger radii circle_radius_m *= 10; } // move to edge of circle (verify_circle) will ensure we begin circling once we reach the edge circle_movetoedge_start(circle_center, circle_radius_m); } // do_loiter_time - initiate loitering at a point for a given time period // note: caller should set yaw_mode void ModeAuto::do_loiter_time(const AP_Mission::Mission_Command& cmd) { // re-use loiter unlimited do_loiter_unlimited(cmd); // setup loiter timer loiter_time = 0; loiter_time_max = cmd.p1; // units are (seconds) } // do_loiter_alt - initiate loitering at a point until a given altitude is reached // note: caller should set yaw_mode void ModeAuto::do_loiter_to_alt(const AP_Mission::Mission_Command& cmd) { // re-use loiter unlimited do_loiter_unlimited(cmd); // if we aren't navigating to a location then we have to adjust // altitude for current location Location target_loc(cmd.content.location); if (target_loc.lat == 0 && target_loc.lng == 0) { target_loc.lat = copter.current_loc.lat; target_loc.lng = copter.current_loc.lng; } if (!target_loc.get_alt_cm(Location::AltFrame::ABOVE_HOME, loiter_to_alt.alt)) { loiter_to_alt.reached_destination_xy = true; loiter_to_alt.reached_alt = true; gcs().send_text(MAV_SEVERITY_INFO, "bad do_loiter_to_alt"); return; } loiter_to_alt.reached_destination_xy = false; loiter_to_alt.loiter_start_done = false; loiter_to_alt.reached_alt = false; loiter_to_alt.alt_error_cm = 0; // set vertical speed and acceleration limits pos_control->set_max_speed_accel_z(wp_nav->get_default_speed_down(), wp_nav->get_default_speed_up(), wp_nav->get_accel_z()); pos_control->set_correction_speed_accel_z(wp_nav->get_default_speed_down(), wp_nav->get_default_speed_up(), wp_nav->get_accel_z()); // set submode set_submode(SubMode::LOITER_TO_ALT); } // do_spline_wp - initiate move to next waypoint void ModeAuto::do_spline_wp(const AP_Mission::Mission_Command& cmd) { // calculate default location used when lat, lon or alt is zero Location default_loc = copter.current_loc; if (wp_nav->is_active() && wp_nav->reached_wp_destination()) { if (!wp_nav->get_wp_destination_loc(default_loc)) { // this should never happen INTERNAL_ERROR(AP_InternalError::error_t::flow_of_control); } } // get spline's location and next location from command and send to wp_nav Location dest_loc, next_dest_loc; bool next_dest_loc_is_spline; get_spline_from_cmd(cmd, default_loc, dest_loc, next_dest_loc, next_dest_loc_is_spline); if (!wp_nav->set_spline_destination_loc(dest_loc, next_dest_loc, next_dest_loc_is_spline)) { // failure to set destination can only be because of missing terrain data copter.failsafe_terrain_on_event(); return; } // this will be used to remember the time in millis after we reach or pass the WP. loiter_time = 0; // this is the delay, stored in seconds loiter_time_max = cmd.p1; // set next destination if necessary if (!set_next_wp(cmd, dest_loc)) { // failure to set next destination can only be because of missing terrain data copter.failsafe_terrain_on_event(); return; } // initialise yaw // To-Do: reset the yaw only when the previous navigation command is not a WP. this would allow removing the special check for ROI if (auto_yaw.mode() != AUTO_YAW_ROI) { auto_yaw.set_mode_to_default(false); } // set submode set_submode(SubMode::WP); } // calculate locations required to build a spline curve from a mission command // dest_loc is populated from cmd's location using default_loc in cases where the lat and lon or altitude is zero // next_dest_loc and nest_dest_loc_is_spline is filled in with the following navigation command's location if it exists. If it does not exist it is set to the dest_loc and false void ModeAuto::get_spline_from_cmd(const AP_Mission::Mission_Command& cmd, const Location& default_loc, Location& dest_loc, Location& next_dest_loc, bool& next_dest_loc_is_spline) { dest_loc = loc_from_cmd(cmd, default_loc); // if there is no delay at the end of this segment get next nav command AP_Mission::Mission_Command temp_cmd; if (cmd.p1 == 0 && mission.get_next_nav_cmd(cmd.index+1, temp_cmd)) { next_dest_loc = loc_from_cmd(temp_cmd, dest_loc); next_dest_loc_is_spline = temp_cmd.id == MAV_CMD_NAV_SPLINE_WAYPOINT; } else { next_dest_loc = dest_loc; next_dest_loc_is_spline = false; } } #if NAV_GUIDED == ENABLED // do_nav_guided_enable - initiate accepting commands from external nav computer void ModeAuto::do_nav_guided_enable(const AP_Mission::Mission_Command& cmd) { if (cmd.p1 > 0) { // start guided within auto nav_guided_start(); } } // do_guided_limits - pass guided limits to guided controller void ModeAuto::do_guided_limits(const AP_Mission::Mission_Command& cmd) { copter.mode_guided.limit_set( cmd.p1 * 1000, // convert seconds to ms cmd.content.guided_limits.alt_min * 100.0f, // convert meters to cm cmd.content.guided_limits.alt_max * 100.0f, // convert meters to cm cmd.content.guided_limits.horiz_max * 100.0f); // convert meters to cm } #endif // NAV_GUIDED // do_nav_delay - Delay the next navigation command void ModeAuto::do_nav_delay(const AP_Mission::Mission_Command& cmd) { nav_delay_time_start_ms = millis(); if (cmd.content.nav_delay.seconds > 0) { // relative delay nav_delay_time_max_ms = cmd.content.nav_delay.seconds * 1000; // convert seconds to milliseconds } else { // absolute delay to utc time nav_delay_time_max_ms = AP::rtc().get_time_utc(cmd.content.nav_delay.hour_utc, cmd.content.nav_delay.min_utc, cmd.content.nav_delay.sec_utc, 0); } gcs().send_text(MAV_SEVERITY_INFO, "Delaying %u sec", (unsigned)(nav_delay_time_max_ms/1000)); } #if AP_SCRIPTING_ENABLED // start accepting position, velocity and acceleration targets from lua scripts void ModeAuto::do_nav_script_time(const AP_Mission::Mission_Command& cmd) { // call regular guided flight mode initialisation if (copter.mode_guided.init(true)) { nav_scripting.done = false; nav_scripting.id++; nav_scripting.start_ms = millis(); nav_scripting.command = cmd.content.nav_script_time.command; nav_scripting.timeout_s = cmd.content.nav_script_time.timeout_s; nav_scripting.arg1 = cmd.content.nav_script_time.arg1; nav_scripting.arg2 = cmd.content.nav_script_time.arg2; set_submode(SubMode::NAV_SCRIPT_TIME); } else { // for safety we set nav_scripting to done to protect against the mission getting stuck nav_scripting.done = true; } } #endif // start maintaining an attitude for a specified time void ModeAuto::do_nav_attitude_time(const AP_Mission::Mission_Command& cmd) { // copy command arguments into local structure nav_attitude_time.roll_deg = cmd.content.nav_attitude_time.roll_deg; nav_attitude_time.pitch_deg = cmd.content.nav_attitude_time.pitch_deg; nav_attitude_time.yaw_deg = cmd.content.nav_attitude_time.yaw_deg; nav_attitude_time.climb_rate = cmd.content.nav_attitude_time.climb_rate; nav_attitude_time.start_ms = AP_HAL::millis(); set_submode(SubMode::NAV_ATTITUDE_TIME); } /********************************************************************************/ // Condition (May) commands /********************************************************************************/ void ModeAuto::do_wait_delay(const AP_Mission::Mission_Command& cmd) { condition_start = millis(); condition_value = cmd.content.delay.seconds * 1000; // convert seconds to milliseconds } void ModeAuto::do_within_distance(const AP_Mission::Mission_Command& cmd) { condition_value = cmd.content.distance.meters * 100; } void ModeAuto::do_yaw(const AP_Mission::Mission_Command& cmd) { auto_yaw.set_fixed_yaw( cmd.content.yaw.angle_deg, cmd.content.yaw.turn_rate_dps, cmd.content.yaw.direction, cmd.content.yaw.relative_angle > 0); } /********************************************************************************/ // Do (Now) commands /********************************************************************************/ void ModeAuto::do_change_speed(const AP_Mission::Mission_Command& cmd) { if (cmd.content.speed.target_ms > 0) { if (cmd.content.speed.speed_type == 2) { copter.wp_nav->set_speed_up(cmd.content.speed.target_ms * 100.0f); } else if (cmd.content.speed.speed_type == 3) { copter.wp_nav->set_speed_down(cmd.content.speed.target_ms * 100.0f); } else { copter.wp_nav->set_speed_xy(cmd.content.speed.target_ms * 100.0f); } } } void ModeAuto::do_set_home(const AP_Mission::Mission_Command& cmd) { if (cmd.p1 == 1 || (cmd.content.location.lat == 0 && cmd.content.location.lng == 0 && cmd.content.location.alt == 0)) { if (!copter.set_home_to_current_location(false)) { // ignore failure } } else { if (!copter.set_home(cmd.content.location, false)) { // ignore failure } } } // do_roi - starts actions required by MAV_CMD_DO_SET_ROI // this involves either moving the camera to point at the ROI (region of interest) // and possibly rotating the copter to point at the ROI if our mount type does not support a yaw feature // TO-DO: add support for other features of MAV_CMD_DO_SET_ROI including pointing at a given waypoint void ModeAuto::do_roi(const AP_Mission::Mission_Command& cmd) { auto_yaw.set_roi(cmd.content.location); } // point the camera to a specified angle void ModeAuto::do_mount_control(const AP_Mission::Mission_Command& cmd) { #if HAL_MOUNT_ENABLED // if vehicle has a camera mount but it doesn't do pan control then yaw the entire vehicle instead if ((copter.camera_mount.get_mount_type() != copter.camera_mount.MountType::Mount_Type_None) && !copter.camera_mount.has_pan_control()) { auto_yaw.set_yaw_angle_rate(cmd.content.mount_control.yaw,0.0f); } // pass the target angles to the camera mount copter.camera_mount.set_angle_target(cmd.content.mount_control.roll, cmd.content.mount_control.pitch, cmd.content.mount_control.yaw, false); #endif } #if WINCH_ENABLED == ENABLED // control winch based on mission command void ModeAuto::do_winch(const AP_Mission::Mission_Command& cmd) { // Note: we ignore the gripper num parameter because we only support one gripper switch (cmd.content.winch.action) { case WINCH_RELAXED: g2.winch.relax(); break; case WINCH_RELATIVE_LENGTH_CONTROL: g2.winch.release_length(cmd.content.winch.release_length); break; case WINCH_RATE_CONTROL: g2.winch.set_desired_rate(cmd.content.winch.release_rate); break; default: // do nothing break; } } #endif // do_payload_place - initiate placing procedure void ModeAuto::do_payload_place(const AP_Mission::Mission_Command& cmd) { // if location provided we fly to that location at current altitude if (cmd.content.location.lat != 0 || cmd.content.location.lng != 0) { // set state to fly to location nav_payload_place.state = PayloadPlaceStateType_FlyToLocation; // convert cmd to location class Location target_loc(cmd.content.location); if (!shift_alt_to_current_alt(target_loc)) { // this can only fail due to missing terrain database alt or rangefinder alt // use current alt-above-home and report error target_loc.set_alt_cm(copter.current_loc.alt, Location::AltFrame::ABOVE_HOME); AP::logger().Write_Error(LogErrorSubsystem::TERRAIN, LogErrorCode::MISSING_TERRAIN_DATA); gcs().send_text(MAV_SEVERITY_CRITICAL, "PayloadPlace: no terrain data, using alt-above-home"); } wp_start(target_loc); } else { nav_payload_place.state = PayloadPlaceStateType_Calibrating_Hover_Start; // initialise placing controller payload_place_start(); } nav_payload_place.descend_max = cmd.p1; } // do_RTL - start Return-to-Launch void ModeAuto::do_RTL(void) { // start rtl in auto flight mode rtl_start(); } /********************************************************************************/ // Verify Nav (Must) commands /********************************************************************************/ // verify_takeoff - check if we have completed the takeoff bool ModeAuto::verify_takeoff() { #if LANDING_GEAR_ENABLED == ENABLED // if we have reached our destination if (auto_takeoff_complete) { // retract the landing gear copter.landinggear.retract_after_takeoff(); } #endif return auto_takeoff_complete; } // verify_land - returns true if landing has been completed bool ModeAuto::verify_land() { bool retval = false; switch (state) { case State::FlyToLocation: // check if we've reached the location if (copter.wp_nav->reached_wp_destination()) { // initialise landing controller land_start(); // advance to next state state = State::Descending; } break; case State::Descending: // rely on THROTTLE_LAND mode to correctly update landing status retval = copter.ap.land_complete && (motors->get_spool_state() == AP_Motors::SpoolState::GROUND_IDLE); if (retval && !mission.continue_after_land_check_for_takeoff() && copter.motors->armed()) { /* we want to stop mission processing on land completion. Disarm now, then return false. This leaves mission state machine in the current NAV_LAND mission item. After disarming the mission will reset */ copter.arming.disarm(AP_Arming::Method::LANDED); retval = false; } break; default: // this should never happen INTERNAL_ERROR(AP_InternalError::error_t::flow_of_control); retval = true; break; } // true is returned if we've successfully landed return retval; } #define NAV_PAYLOAD_PLACE_DEBUGGING 0 #if NAV_PAYLOAD_PLACE_DEBUGGING #include #define debug(fmt, args ...) do {::fprintf(stderr,"%s:%d: " fmt "\n", __FUNCTION__, __LINE__, ## args); } while(0) #else #define debug(fmt, args ...) #endif // verify_payload_place - returns true if placing has been completed bool ModeAuto::verify_payload_place() { const uint16_t hover_throttle_calibrate_time = 2000; // milliseconds const uint16_t descend_throttle_calibrate_time = 2000; // milliseconds const uint16_t measure_time = 1000; // milliseconds const float hover_throttle_placed_fraction = 0.7; // i.e. if throttle is less than 70% of hover we have placed const float descent_throttle_placed_fraction = 0.9; // i.e. if throttle is less than 90% of descent throttle we have placed const uint16_t placed_time = 500; // how long we have to be below a throttle threshold before considering placed const float current_throttle_level = motors->get_throttle(); const uint32_t now = AP_HAL::millis(); // if we discover we've landed then immediately release the load: if (copter.ap.land_complete || copter.ap.land_complete_maybe) { switch (nav_payload_place.state) { case PayloadPlaceStateType_FlyToLocation: case PayloadPlaceStateType_Calibrating_Hover_Start: case PayloadPlaceStateType_Calibrating_Hover: case PayloadPlaceStateType_Descending_Start: case PayloadPlaceStateType_Descending: gcs().send_text(MAV_SEVERITY_INFO, "PayloadPlace: landed"); nav_payload_place.state = PayloadPlaceStateType_Releasing_Start; break; case PayloadPlaceStateType_Releasing_Start: case PayloadPlaceStateType_Releasing: case PayloadPlaceStateType_Released: case PayloadPlaceStateType_Ascending_Start: case PayloadPlaceStateType_Ascending: case PayloadPlaceStateType_Done: break; } } switch (nav_payload_place.state) { case PayloadPlaceStateType_FlyToLocation: if (!copter.wp_nav->reached_wp_destination()) { return false; } payload_place_start(); return false; case PayloadPlaceStateType_Calibrating_Hover_Start: // hover for 2 seconds to measure hover thrust debug("Calibrate start"); nav_payload_place.hover_start_timestamp = now; nav_payload_place.hover_throttle_level = 1.0; nav_payload_place.state = PayloadPlaceStateType_Calibrating_Hover; FALLTHROUGH; case PayloadPlaceStateType_Calibrating_Hover: { if (now - nav_payload_place.hover_start_timestamp < hover_throttle_calibrate_time - measure_time) { // waiting for aircraft to settle return false; } if (now - nav_payload_place.hover_start_timestamp < hover_throttle_calibrate_time) { // measure hover thrust nav_payload_place.hover_throttle_level = MIN(nav_payload_place.hover_throttle_level, current_throttle_level); return false; } // hover thrust has been measured gcs().send_text(MAV_SEVERITY_INFO, "PayloadPlace: payload hover throttle: %f", static_cast(nav_payload_place.hover_throttle_level)); nav_payload_place.state = PayloadPlaceStateType_Descending_Start; } FALLTHROUGH; case PayloadPlaceStateType_Descending_Start: nav_payload_place.descend_start_timestamp = now; nav_payload_place.descend_start_altitude = inertial_nav.get_position_z_up_cm(); nav_payload_place.descend_throttle_level = 1.0; nav_payload_place.state = PayloadPlaceStateType_Descending; FALLTHROUGH; case PayloadPlaceStateType_Descending: // make sure we don't descend too far debug("descended: %f cm (%f cm max)", (nav_payload_place.descend_start_altitude - inertial_nav.get_position_z_up_cm()), nav_payload_place.descend_max); if (!is_zero(nav_payload_place.descend_max) && nav_payload_place.descend_start_altitude - inertial_nav.get_position_z_up_cm() > nav_payload_place.descend_max) { nav_payload_place.state = PayloadPlaceStateType_Ascending_Start; gcs().send_text(MAV_SEVERITY_WARNING, "PayloadPlace: Reached maximum descent"); return false; // we'll do any cleanups required next time through the loop } // if the aircraft has been descending long enough, calibrate the decent thrust if ((now - nav_payload_place.descend_start_timestamp > descend_throttle_calibrate_time - measure_time) && (now - nav_payload_place.descend_start_timestamp < descend_throttle_calibrate_time)) { // measure decent thrust nav_payload_place.descend_throttle_level = MIN(nav_payload_place.descend_throttle_level, current_throttle_level); } // check for reduced thrust requirement indicating possible payload touch down if (current_throttle_level > hover_throttle_placed_fraction * nav_payload_place.hover_throttle_level && (now - nav_payload_place.descend_start_timestamp < descend_throttle_calibrate_time || current_throttle_level > descent_throttle_placed_fraction * nav_payload_place.descend_throttle_level)) { // throttle is above both threshold ratios (or above hover threshold ration and descent threshold ratio not yet valid) nav_payload_place.place_start_timestamp = now; return false; } if (now - nav_payload_place.place_start_timestamp < placed_time) { // continue decent debug("Place Timer: %d", now - nav_payload_place.place_start_timestamp); return false; } nav_payload_place.state = PayloadPlaceStateType_Releasing_Start; FALLTHROUGH; case PayloadPlaceStateType_Releasing_Start: // Reinitialise vertical position controller to remove discontinuity due to touch down of payload pos_control->init_z_controller_no_descent(); #if GRIPPER_ENABLED == ENABLED if (g2.gripper.valid()) { gcs().send_text(MAV_SEVERITY_INFO, "PayloadPlace: Releasing the gripper"); g2.gripper.release(); } else { gcs().send_text(MAV_SEVERITY_INFO, "PayloadPlace: Gripper not valid"); nav_payload_place.state = PayloadPlaceStateType_Ascending_Start; return false; } #else gcs().send_text(MAV_SEVERITY_INFO, "Gripper code disabled"); nav_payload_place.state = PayloadPlaceStateType_Ascending_Start; return false; #endif nav_payload_place.state = PayloadPlaceStateType_Releasing; FALLTHROUGH; case PayloadPlaceStateType_Releasing: #if GRIPPER_ENABLED == ENABLED if (g2.gripper.valid() && !g2.gripper.released()) { return false; } #endif nav_payload_place.state = PayloadPlaceStateType_Released; FALLTHROUGH; case PayloadPlaceStateType_Released: { nav_payload_place.state = PayloadPlaceStateType_Ascending_Start; } FALLTHROUGH; case PayloadPlaceStateType_Ascending_Start: { auto_takeoff_start(nav_payload_place.descend_start_altitude, false); nav_payload_place.state = PayloadPlaceStateType_Ascending; } FALLTHROUGH; case PayloadPlaceStateType_Ascending: if (!auto_takeoff_complete) { return false; } nav_payload_place.state = PayloadPlaceStateType_Done; FALLTHROUGH; case PayloadPlaceStateType_Done: return true; default: // this should never happen INTERNAL_ERROR(AP_InternalError::error_t::flow_of_control); return true; } // should never get here return true; } #undef debug bool ModeAuto::verify_loiter_unlimited() { return false; } // verify_loiter_time - check if we have loitered long enough bool ModeAuto::verify_loiter_time(const AP_Mission::Mission_Command& cmd) { // return immediately if we haven't reached our destination if (!copter.wp_nav->reached_wp_destination()) { return false; } // start our loiter timer if ( loiter_time == 0 ) { loiter_time = millis(); } // check if loiter timer has run out if (((millis() - loiter_time) / 1000) >= loiter_time_max) { gcs().send_text(MAV_SEVERITY_INFO, "Reached command #%i",cmd.index); return true; } return false; } // verify_loiter_to_alt - check if we have reached both destination // (roughly) and altitude (precisely) bool ModeAuto::verify_loiter_to_alt() const { if (loiter_to_alt.reached_destination_xy && loiter_to_alt.reached_alt) { return true; } return false; } // verify_RTL - handles any state changes required to implement RTL // do_RTL should have been called once first to initialise all variables // returns true with RTL has completed successfully bool ModeAuto::verify_RTL() { return (copter.mode_rtl.state_complete() && (copter.mode_rtl.state() == ModeRTL::SubMode::FINAL_DESCENT || copter.mode_rtl.state() == ModeRTL::SubMode::LAND) && (motors->get_spool_state() == AP_Motors::SpoolState::GROUND_IDLE)); } /********************************************************************************/ // Verify Condition (May) commands /********************************************************************************/ bool ModeAuto::verify_wait_delay() { if (millis() - condition_start > (uint32_t)MAX(condition_value,0)) { condition_value = 0; return true; } return false; } bool ModeAuto::verify_within_distance() { if (wp_distance() < (uint32_t)MAX(condition_value,0)) { condition_value = 0; return true; } return false; } // verify_yaw - return true if we have reached the desired heading bool ModeAuto::verify_yaw() { // make sure still in fixed yaw mode, the waypoint controller often retakes control of yaw as it executes a new waypoint command auto_yaw.set_mode(AUTO_YAW_FIXED); // check if we are within 2 degrees of the target heading return auto_yaw.fixed_yaw_slew_finished() && (fabsf(wrap_180_cd(ahrs.yaw_sensor-auto_yaw.yaw())) <= 200); } // verify_nav_wp - check if we have reached the next way point bool ModeAuto::verify_nav_wp(const AP_Mission::Mission_Command& cmd) { // check if we have reached the waypoint if ( !copter.wp_nav->reached_wp_destination() ) { return false; } // start timer if necessary if (loiter_time == 0) { loiter_time = millis(); if (loiter_time_max > 0) { // play a tone AP_Notify::events.waypoint_complete = 1; } } // check if timer has run out if (((millis() - loiter_time) / 1000) >= loiter_time_max) { if (loiter_time_max == 0) { // play a tone AP_Notify::events.waypoint_complete = 1; } gcs().send_text(MAV_SEVERITY_INFO, "Reached command #%i",cmd.index); return true; } return false; } // verify_circle - check if we have circled the point enough bool ModeAuto::verify_circle(const AP_Mission::Mission_Command& cmd) { // check if we've reached the edge if (_mode == SubMode::CIRCLE_MOVE_TO_EDGE) { if (copter.wp_nav->reached_wp_destination()) { // start circling circle_start(); } return false; } // check if we have completed circling return fabsf(copter.circle_nav->get_angle_total()/float(M_2PI)) >= LOWBYTE(cmd.p1); } // verify_spline_wp - check if we have reached the next way point using spline bool ModeAuto::verify_spline_wp(const AP_Mission::Mission_Command& cmd) { // check if we have reached the waypoint if ( !copter.wp_nav->reached_wp_destination() ) { return false; } // start timer if necessary if (loiter_time == 0) { loiter_time = millis(); } // check if timer has run out if (((millis() - loiter_time) / 1000) >= loiter_time_max) { gcs().send_text(MAV_SEVERITY_INFO, "Reached command #%i",cmd.index); return true; } return false; } #if NAV_GUIDED == ENABLED // verify_nav_guided - check if we have breached any limits bool ModeAuto::verify_nav_guided_enable(const AP_Mission::Mission_Command& cmd) { // if disabling guided mode then immediately return true so we move to next command if (cmd.p1 == 0) { return true; } // check time and position limits return copter.mode_guided.limit_check(); } #endif // NAV_GUIDED // verify_nav_delay - check if we have waited long enough bool ModeAuto::verify_nav_delay(const AP_Mission::Mission_Command& cmd) { if (millis() - nav_delay_time_start_ms > nav_delay_time_max_ms) { nav_delay_time_max_ms = 0; return true; } return false; } #if AP_SCRIPTING_ENABLED // check if verify_nav_script_time command has completed bool ModeAuto::verify_nav_script_time() { // if done or timeout then return true if (nav_scripting.done || ((nav_scripting.timeout_s > 0) && (AP_HAL::millis() - nav_scripting.start_ms) > (nav_scripting.timeout_s * 1000))) { return true; } return false; } #endif // check if nav_attitude_time command has completed bool ModeAuto::verify_nav_attitude_time(const AP_Mission::Mission_Command& cmd) { return ((AP_HAL::millis() - nav_attitude_time.start_ms) > (cmd.content.nav_attitude_time.time_sec * 1000)); } // pause - Prevent aircraft from progressing along the track bool ModeAuto::pause() { // do not pause if already paused or not in the WP sub mode or already reached to the destination if(wp_nav->paused() || _mode != SubMode::WP || wp_nav->reached_wp_destination()) { return false; } wp_nav->set_pause(); return true; } // resume - Allow aircraft to progress along the track bool ModeAuto::resume() { // do not resume if not paused before if(!wp_nav->paused()) { return false; } wp_nav->set_resume(); return true; } #endif