#include "Copter.h"

#if MODE_THROW_ENABLED == ENABLED

// throw_init - initialise throw controller
bool ModeThrow::init(bool ignore_checks)
{
#if FRAME_CONFIG == HELI_FRAME
    // do not allow helis to use throw to start
    return false;
#endif

    // do not enter the mode when already armed or when flying
    if (motors->armed()) {
        return false;
    }

    // init state
    stage = Throw_Disarmed;
    nextmode_attempted = false;

    return true;
}

// runs the throw to start controller
// should be called at 100hz or more
void ModeThrow::run()
{
    /* Throw State Machine
    Throw_Disarmed - motors are off
    Throw_Detecting -  motors are on and we are waiting for the throw
    Throw_Uprighting - the throw has been detected and the copter is being uprighted
    Throw_HgtStabilise - the copter is kept level and  height is stabilised about the target height
    Throw_PosHold - the copter is kept at a constant position and height
    */

    if (!motors->armed()) {
        // state machine entry is always from a disarmed state
        stage = Throw_Disarmed;

    } else if (stage == Throw_Disarmed && motors->armed()) {
        gcs().send_text(MAV_SEVERITY_INFO,"waiting for throw");
        stage = Throw_Detecting;

    } else if (stage == Throw_Detecting && throw_detected()){
        gcs().send_text(MAV_SEVERITY_INFO,"throw detected - uprighting");
        stage = Throw_Uprighting;

        // Cancel the waiting for throw tone sequence
        AP_Notify::flags.waiting_for_throw = false;

    } else if (stage == Throw_Uprighting && throw_attitude_good()) {
        gcs().send_text(MAV_SEVERITY_INFO,"uprighted - controlling height");
        stage = Throw_HgtStabilise;

        // initialize vertical speed and acceleration limits
        // use brake mode values for rapid response
        pos_control->set_max_speed_z(BRAKE_MODE_SPEED_Z, BRAKE_MODE_SPEED_Z);
        pos_control->set_max_accel_z(BRAKE_MODE_DECEL_RATE);

        // initialise the demanded height to 3m above the throw height
        // we want to rapidly clear surrounding obstacles
        if (g2.throw_type == ThrowType::Drop) {
            pos_control->set_alt_target(inertial_nav.get_altitude() - 100);
        } else {
            pos_control->set_alt_target(inertial_nav.get_altitude() + 300);
        }

        // set the initial velocity of the height controller demand to the measured velocity if it is going up
        // if it is going down, set it to zero to enforce a very hard stop
        pos_control->set_desired_velocity_z(fmaxf(inertial_nav.get_velocity_z(),0.0f));

        // Set the auto_arm status to true to avoid a possible automatic disarm caused by selection of an auto mode with throttle at minimum
        copter.set_auto_armed(true);

    } else if (stage == Throw_HgtStabilise && throw_height_good()) {
        gcs().send_text(MAV_SEVERITY_INFO,"height achieved - controlling position");
        stage = Throw_PosHold;

        // initialise the loiter target to the current position and velocity
        loiter_nav->clear_pilot_desired_acceleration();
        loiter_nav->init_target();

        // Set the auto_arm status to true to avoid a possible automatic disarm caused by selection of an auto mode with throttle at minimum
        copter.set_auto_armed(true);
    } else if (stage == Throw_PosHold && throw_position_good()) {
        if (!nextmode_attempted) {
            switch ((Mode::Number)g2.throw_nextmode.get()) {
                case Mode::Number::AUTO:
                case Mode::Number::GUIDED:
                case Mode::Number::RTL:
                case Mode::Number::LAND:
                case Mode::Number::BRAKE:
                case Mode::Number::LOITER:
                    set_mode((Mode::Number)g2.throw_nextmode.get(), ModeReason::THROW_COMPLETE);
                    break;
                default:
                    // do nothing
                    break;
            }
            nextmode_attempted = true;
        }
    }

    // Throw State Processing
    switch (stage) {

    case Throw_Disarmed:

        // prevent motors from rotating before the throw is detected unless enabled by the user
        if (g.throw_motor_start == PreThrowMotorState::RUNNING) {
            motors->set_desired_spool_state(AP_Motors::DesiredSpoolState::GROUND_IDLE);
        } else {
            motors->set_desired_spool_state(AP_Motors::DesiredSpoolState::SHUT_DOWN);
        }

        // demand zero throttle (motors will be stopped anyway) and continually reset the attitude controller
        attitude_control->set_yaw_target_to_current_heading();
        attitude_control->reset_rate_controller_I_terms();
        attitude_control->set_throttle_out(0,true,g.throttle_filt);
        break;

    case Throw_Detecting:

        // prevent motors from rotating before the throw is detected unless enabled by the user
        if (g.throw_motor_start == PreThrowMotorState::RUNNING) {
            motors->set_desired_spool_state(AP_Motors::DesiredSpoolState::GROUND_IDLE);
        } else {
            motors->set_desired_spool_state(AP_Motors::DesiredSpoolState::SHUT_DOWN);
        }

        // Hold throttle at zero during the throw and continually reset the attitude controller
        attitude_control->set_yaw_target_to_current_heading();
        attitude_control->reset_rate_controller_I_terms();
        attitude_control->set_throttle_out(0,true,g.throttle_filt);

        // Play the waiting for throw tone sequence to alert the user
        AP_Notify::flags.waiting_for_throw = true;

        break;

    case Throw_Uprighting:

        // set motors to full range
        motors->set_desired_spool_state(AP_Motors::DesiredSpoolState::THROTTLE_UNLIMITED);

        // demand a level roll/pitch attitude with zero yaw rate
        attitude_control->input_euler_angle_roll_pitch_euler_rate_yaw(0.0f, 0.0f, 0.0f);

        // output 50% throttle and turn off angle boost to maximise righting moment
        attitude_control->set_throttle_out(0.5f, false, g.throttle_filt);

        break;

    case Throw_HgtStabilise:

        // set motors to full range
        motors->set_desired_spool_state(AP_Motors::DesiredSpoolState::THROTTLE_UNLIMITED);

        // call attitude controller
        attitude_control->input_euler_angle_roll_pitch_euler_rate_yaw(0.0f, 0.0f, 0.0f);

        // call height controller
        pos_control->set_alt_target_from_climb_rate_ff(0.0f, G_Dt, false);
        pos_control->update_z_controller();

        break;

    case Throw_PosHold:

        // set motors to full range
        motors->set_desired_spool_state(AP_Motors::DesiredSpoolState::THROTTLE_UNLIMITED);

        // run loiter controller
        loiter_nav->update();

        // call attitude controller
        attitude_control->input_euler_angle_roll_pitch_euler_rate_yaw(loiter_nav->get_roll(), loiter_nav->get_pitch(), 0.0f);

        // call height controller
        pos_control->set_alt_target_from_climb_rate_ff(0.0f, G_Dt, false);
        pos_control->update_z_controller();

        break;
    }

    // log at 10hz or if stage changes
    uint32_t now = AP_HAL::millis();
    if ((stage != prev_stage) || (now - last_log_ms) > 100) {
        prev_stage = stage;
        last_log_ms = now;
        const float velocity = inertial_nav.get_velocity().length();
        const float velocity_z = inertial_nav.get_velocity().z;
        const float accel = copter.ins.get_accel().length();
        const float ef_accel_z = ahrs.get_accel_ef().z;
        const bool throw_detect = (stage > Throw_Detecting) || throw_detected();
        const bool attitude_ok = (stage > Throw_Uprighting) || throw_attitude_good();
        const bool height_ok = (stage > Throw_HgtStabilise) || throw_height_good();
        const bool pos_ok = (stage > Throw_PosHold) || throw_position_good();
        
// @LoggerMessage: THRO
// @Description: Throw Mode messages
// @URL: https://ardupilot.org/copter/docs/throw-mode.html
// @Field: TimeUS: Time since system startup
// @Field: Stage: Current stage of the Throw Mode
// @Field: Vel: Magnitude of the velocity vector
// @Field: VelZ: Vertical Velocity
// @Field: Acc: Magnitude of the vector of the current acceleration
// @Field: AccEfZ: Vertical earth frame accelerometer value
// @Field: Throw: True if a throw has been detected since entering this mode
// @Field: AttOk: True if the vehicle is upright 
// @Field: HgtOk: True if the vehicle is within 50cm of the demanded height
// @Field: PosOk: True if the vehicle is within 50cm of the demanded horizontal position
        
        AP::logger().Write(
            "THRO",
            "TimeUS,Stage,Vel,VelZ,Acc,AccEfZ,Throw,AttOk,HgtOk,PosOk",
            "s-nnoo----",
            "F-0000----",
            "QBffffbbbb",
            AP_HAL::micros64(),
            (uint8_t)stage,
            (double)velocity,
            (double)velocity_z,
            (double)accel,
            (double)ef_accel_z,
            throw_detect,
            attitude_ok,
            height_ok,
            pos_ok);
    }
}

bool ModeThrow::throw_detected()
{
    // Check that we have a valid navigation solution
    nav_filter_status filt_status = inertial_nav.get_filter_status();
    if (!filt_status.flags.attitude || !filt_status.flags.horiz_pos_abs || !filt_status.flags.vert_pos) {
        return false;
    }

    // Check for high speed (>500 cm/s)
    bool high_speed = inertial_nav.get_velocity().length() > THROW_HIGH_SPEED;

    // check for upwards or downwards trajectory (airdrop) of 50cm/s
    bool changing_height;
    if (g2.throw_type == ThrowType::Drop) {
        changing_height = inertial_nav.get_velocity().z < -THROW_VERTICAL_SPEED;
    } else {
        changing_height = inertial_nav.get_velocity().z > THROW_VERTICAL_SPEED;
    }

    // Check the vertical acceleraton is greater than 0.25g
    bool free_falling = ahrs.get_accel_ef().z > -0.25 * GRAVITY_MSS;

    // Check if the accel length is < 1.0g indicating that any throw action is complete and the copter has been released
    bool no_throw_action = copter.ins.get_accel().length() < 1.0f * GRAVITY_MSS;

    // High velocity or free-fall combined with increasing height indicate a possible air-drop or throw release
    bool possible_throw_detected = (free_falling || high_speed) && changing_height && no_throw_action;

    // Record time and vertical velocity when we detect the possible throw
    if (possible_throw_detected && ((AP_HAL::millis() - free_fall_start_ms) > 500)) {
        free_fall_start_ms = AP_HAL::millis();
        free_fall_start_velz = inertial_nav.get_velocity().z;
    }

    // Once a possible throw condition has been detected, we check for 2.5 m/s of downwards velocity change in less than 0.5 seconds to confirm
    bool throw_condition_confirmed = ((AP_HAL::millis() - free_fall_start_ms < 500) && ((inertial_nav.get_velocity().z - free_fall_start_velz) < -250.0f));

    // start motors and enter the control mode if we are in continuous freefall
    return throw_condition_confirmed;
}

bool ModeThrow::throw_attitude_good()
{
    // Check that we have uprighted the copter
    const Matrix3f &rotMat = ahrs.get_rotation_body_to_ned();
    return (rotMat.c.z > 0.866f); // is_upright
}

bool ModeThrow::throw_height_good()
{
    // Check that we are within 0.5m of the demanded height
    return (pos_control->get_alt_error() < 50.0f);
}

bool ModeThrow::throw_position_good()
{
    // check that our horizontal position error is within 50cm
    return (pos_control->get_pos_error_xy() < 50.0f);
}
#endif