# hw definition file for processing by chibios_pins.py # MCU class and specific type MCU STM32F100 STM32F100xB FLASH_RESERVE_START_KB 4 # board ID for firmware load APJ_BOARD_ID 3 # crystal frequency OSCILLATOR_HZ 24000000 define CH_CFG_ST_FREQUENCY 1000 FLASH_SIZE_KB 64 # ChibiOS system timer # order of UARTs SERIAL_ORDER EMPTY EMPTY EMPTY EMPTY define HAL_USE_UART TRUE # UART connected to FMU, uses DMA PA2 USART2_TX USART2 SPEED_HIGH PA3 USART2_RX USART2 SPEED_HIGH define STM32_UART_USE_USART1 FALSE define STM32_UART_USE_USART2 TRUE define STM32_UART_USE_USART3 FALSE # UART for SBUS out, and RC in, no DMA define HAL_USE_SERIAL TRUE PB4 SBUS_OUT_EN OUTPUT LOW GPIO(1) PB10 USART3_TX USART3 SPEED_HIGH LOW PB11 USART3_RX USART3 define STM32_SERIAL_USE_USART1 TRUE define STM32_SERIAL_USE_USART2 FALSE define STM32_SERIAL_USE_USART3 TRUE PA0 TIM2_CH1 TIM2 PWM(1) GPIO(101) PA1 TIM2_CH2 TIM2 PWM(2) GPIO(102) PB8 TIM4_CH3 TIM4 PWM(3) GPIO(103) PB9 TIM4_CH4 TIM4 PWM(4) GPIO(104) PA6 TIM3_CH1 TIM3 PWM(5) GPIO(105) PA7 TIM3_CH2 TIM3 PWM(6) GPIO(106) PB0 TIM3_CH3 TIM3 PWM(7) GPIO(107) PB1 TIM3_CH4 TIM3 PWM(8) GPIO(108) # pins for detecting board type. On a pixhawk2 PC14 is pulled high, # PC15 is pulled low. On a Pixhawk1 they are both floating PC14 IO_HW_DETECT1 INPUT PULLDOWN PC15 IO_HW_DETECT2 INPUT PULLUP PB14 HEATER INPUT PULLUP GPIO(0) # safety button and LED. These do not use the same names # as those for FMU-only boards as we want to handle them specially # inside the iofirmware PB5 SAFETY_INPUT INPUT PULLDOWN PB13 SAFETY_LED OUTPUT HIGH OPENDRAIN # amber LED PB15 AMBER_LED OUTPUT LOW OPENDRAIN # green ring LED on cube PA11 RING_LED OUTPUT LOW OPENDRAIN # UART for DSM input # TX side is for IO debug, and is unused PA9 USART1_TX USART1 SPEED_HIGH PA10 USART1_RX USART1 SPEED_HIGH PC13 SPEKTRUM_PWR_EN OUTPUT LOW define HAL_GPIO_PIN_SPEKTRUM_OUT PAL_LINE(GPIOA,10U) PA8 RCIN INPUT SPEED_HIGH PULLDOWN # RC Input PPM # analog inputs PA4 VSERVO ADC1 PA5 VRSSI ADC1 define HAL_ADC_VSERVO_CHAN ADC_CHANNEL_IN4 define HAL_ADC_VRSSI_CHAN ADC_CHANNEL_IN5 define HAL_USE_ADC TRUE define STM32_ADC_USE_ADC1 TRUE define HAL_DISABLE_ADC_DRIVER TRUE #Manually define ICU settings define HAL_USE_ICU TRUE define STM32_ICU_USE_TIM1 TRUE define RCIN_ICU_TIMER ICUD1 define RCIN_ICU_CHANNEL ICU_CHANNEL_1 define STM32_RCIN_DMA_STREAM STM32_DMA_STREAM_ID(1, 2) #DMA Channel Not relevant for F1 series define STM32_RCIN_DMA_CHANNEL 0 define HAL_USE_EMPTY_STORAGE 1 define HAL_STORAGE_SIZE 16384 define HAL_INS_DEFAULT HAL_INS_NONE define HAL_BARO_DEFAULT HAL_BARO_NONE define HAL_NO_GPIO_IRQ define CH_CFG_ST_TIMEDELTA 0 #define CH_CFG_USE_DYNAMIC FALSE define SERIAL_BUFFERS_SIZE 32 define HAL_USE_EMPTY_IO TRUE define PORT_INT_REQUIRED_STACK 64 # avoid timer and RCIN threads to save memory define HAL_NO_TIMER_THREAD define HAL_NO_RCIN_THREAD define HAL_NO_MONITOR_THREAD define HAL_NO_RCOUT_THREAD define AP_HAL_SHARED_DMA_ENABLED 0 #defined to turn off undef warnings define __FPU_PRESENT 0 define HAL_USE_RTC FALSE define HAL_NO_FLASH_SUPPORT TRUE define HAL_NO_UARTDRIVER TRUE define DISABLE_SERIAL_ESC_COMM TRUE define HAL_LOGGING_ENABLED 0 define DMA_RESERVE_SIZE 0 # reduce memory usage in RCInput define SOFTSIG_MAX_SIGNAL_TRANSITIONS 128 define IOMCU_FW TRUE define AP_FASTBOOT_ENABLED 0 IOMCU_FW 1 MAIN_STACK 0x200 PROCESS_STACK 0x250 define HAL_DISABLE_LOOP_DELAY define AP_BOOTLOADER_FLASHING_ENABLED 0 define AP_RCPROTOCOL_BACKEND_DEFAULT_ENABLED 0 define AP_RCPROTOCOL_PPMSUM_ENABLED 1 define AP_RCPROTOCOL_IBUS_ENABLED 1 define AP_RCPROTOCOL_SBUS_ENABLED 1 define AP_RCPROTOCOL_DSM_ENABLED 1 define AP_RCPROTOCOL_SUMD_ENABLED 1 define AP_RCPROTOCOL_SRXL_ENABLED 1 define AP_RCPROTOCOL_ST24_ENABLED 1 define AP_RCPROTOCOL_FPORT_ENABLED 1 AUTOBUILD_TARGETS iofirmware