// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*- #ifndef _DEFINES_H #define _DEFINES_H #include // Just so that it's completely clear... #define ENABLED 1 #define DISABLED 0 // this avoids a very common config error #define ENABLE ENABLED #define DISABLE DISABLED // Flight modes // ------------ #define AUTO_YAW_HOLD 0 // pilot controls the heading #define AUTO_YAW_LOOK_AT_NEXT_WP 1 // point towards next waypoint (no pilot input accepted) #define AUTO_YAW_ROI 2 // point towards a location held in roi_WP (no pilot input accepted) #define AUTO_YAW_LOOK_AT_HEADING 3 // point towards a particular angle (not pilot input accepted) #define AUTO_YAW_LOOK_AHEAD 4 // point in the direction the copter is moving #define AUTO_YAW_RESETTOARMEDYAW 5 // point towards heading at time motors were armed // Ch6, Ch7 and Ch8 aux switch control #define AUX_SWITCH_PWM_TRIGGER_HIGH 1800 // pwm value above which the ch7 or ch8 option will be invoked #define AUX_SWITCH_PWM_TRIGGER_LOW 1200 // pwm value below which the ch7 or ch8 option will be disabled #define CH6_PWM_TRIGGER_HIGH 1800 #define CH6_PWM_TRIGGER_LOW 1200 #define AUX_SWITCH_DO_NOTHING 0 // aux switch disabled #define AUX_SWITCH_SET_HOVER 1 // deprecated #define AUX_SWITCH_FLIP 2 // flip #define AUX_SWITCH_SIMPLE_MODE 3 // change to simple mode #define AUX_SWITCH_RTL 4 // change to RTL flight mode #define AUX_SWITCH_SAVE_TRIM 5 // save current position as level #define AUX_SWITCH_ADC_FILTER 6 // deprecated #define AUX_SWITCH_SAVE_WP 7 // save mission waypoint or RTL if in auto mode #define AUX_SWITCH_MULTI_MODE 8 // depending upon CH6 position Flip (if ch6 is low), RTL (if ch6 in middle) or Save WP (if ch6 is high) #define AUX_SWITCH_CAMERA_TRIGGER 9 // trigger camera servo or relay #define AUX_SWITCH_SONAR 10 // allow enabling or disabling sonar in flight which helps avoid surface tracking when you are far above the ground #define AUX_SWITCH_FENCE 11 // allow enabling or disabling fence in flight #define AUX_SWITCH_RESETTOARMEDYAW 12 // changes yaw to be same as when quad was armed #define AUX_SWITCH_SUPERSIMPLE_MODE 13 // change to simple mode in middle, super simple at top #define AUX_SWITCH_ACRO_TRAINER 14 // low = disabled, middle = leveled, high = leveled and limited #define AUX_SWITCH_SPRAYER 15 // enable/disable the crop sprayer #define AUX_SWITCH_AUTO 16 // change to auto flight mode #define AUX_SWITCH_AUTOTUNE 17 // auto tune #define AUX_SWITCH_LAND 18 // change to LAND flight mode #define AUX_SWITCH_EPM 19 // Operate the EPM cargo gripper low=off, middle=neutral, high=on #define AUX_SWITCH_EKF 20 // Enable NavEKF #define AUX_SWITCH_PARACHUTE_ENABLE 21 // Parachute enable/disable #define AUX_SWITCH_PARACHUTE_RELEASE 22 // Parachute release #define AUX_SWITCH_PARACHUTE_3POS 23 // Parachute disable, enable, release with 3 position switch #define AUX_SWITCH_MISSIONRESET 24 // Reset auto mission to start from first command #define AUX_SWITCH_ATTCON_FEEDFWD 25 // enable/disable the roll and pitch rate feed forward #define AUX_SWITCH_ATTCON_ACCEL_LIM 26 // enable/disable the roll, pitch and yaw accel limiting #define AUX_SWITCH_RETRACT_MOUNT 27 // Retract Mount #define AUX_SWITCH_RELAY 28 // Relay pin on/off (only supports first relay) // values used by the ap.ch7_opt and ap.ch8_opt flags #define AUX_SWITCH_LOW 0 // indicates auxiliar switch is in the low position (pwm <1200) #define AUX_SWITCH_MIDDLE 1 // indicates auxiliar switch is in the middle position (pwm >1200, <1800) #define AUX_SWITCH_HIGH 2 // indicates auxiliar switch is in the high position (pwm >1800) // Frame types #define UNDEFINED_FRAME 0 #define QUAD_FRAME 1 #define TRI_FRAME 2 #define HEXA_FRAME 3 #define Y6_FRAME 4 #define OCTA_FRAME 5 #define HELI_FRAME 6 #define OCTA_QUAD_FRAME 7 #define SINGLE_FRAME 8 #define COAX_FRAME 9 // Internal defines, don't edit and expect things to work // ------------------------------------------------------- #define ToRad(x) radians(x) // *pi/180 #define ToDeg(x) degrees(x) // *180/pi // HIL enumerations #define HIL_MODE_DISABLED 0 #define HIL_MODE_SENSORS 1 // Auto Pilot modes // ---------------- #define STABILIZE 0 // hold level position #define ACRO 1 // rate control #define ALT_HOLD 2 // AUTO control #define AUTO 3 // AUTO control #define GUIDED 4 // AUTO control #define LOITER 5 // Hold a single location #define RTL 6 // AUTO control #define CIRCLE 7 // AUTO control #define LAND 9 // AUTO control #define OF_LOITER 10 // Hold a single location using optical flow sensor #define DRIFT 11 // DRIFT mode (Note: 12 is no longer used) #define SPORT 13 // earth frame rate control #define FLIP 14 // flip the vehicle on the roll axis #define AUTOTUNE 15 // autotune the vehicle's roll and pitch gains #define POSHOLD 16 // position hold with manual override #define NUM_MODES 17 // CH_6 Tuning // ----------- #define CH6_NONE 0 // no tuning performed #define CH6_STABILIZE_ROLL_PITCH_KP 1 // stabilize roll/pitch angle controller's P term #define CH6_RATE_ROLL_PITCH_KP 4 // body frame roll/pitch rate controller's P term #define CH6_RATE_ROLL_PITCH_KI 5 // body frame roll/pitch rate controller's I term #define CH6_RATE_ROLL_PITCH_KD 21 // body frame roll/pitch rate controller's D term #define CH6_STABILIZE_YAW_KP 3 // stabilize yaw heading controller's P term #define CH6_YAW_RATE_KP 6 // body frame yaw rate controller's P term #define CH6_YAW_RATE_KD 26 // body frame yaw rate controller's D term #define CH6_ALTITUDE_HOLD_KP 14 // altitude hold controller's P term (alt error to desired rate) #define CH6_THROTTLE_RATE_KP 7 // throttle rate controller's P term (desired rate to acceleration or motor output) #define CH6_THROTTLE_ACCEL_KP 34 // accel based throttle controller's P term #define CH6_THROTTLE_ACCEL_KI 35 // accel based throttle controller's I term #define CH6_THROTTLE_ACCEL_KD 36 // accel based throttle controller's D term #define CH6_LOITER_POSITION_KP 12 // loiter distance controller's P term (position error to speed) #define CH6_LOITER_RATE_KP 22 // loiter rate controller's P term (speed error to tilt angle) #define CH6_LOITER_RATE_KI 28 // loiter rate controller's I term (speed error to tilt angle) #define CH6_LOITER_RATE_KD 23 // loiter rate controller's D term (speed error to tilt angle) #define CH6_WP_SPEED 10 // maximum speed to next way point (0 to 10m/s) #define CH6_ACRO_RP_KP 25 // acro controller's P term. converts pilot input to a desired roll, pitch or yaw rate #define CH6_ACRO_YAW_KP 40 // acro controller's P term. converts pilot input to a desired roll, pitch or yaw rate #define CH6_RELAY 9 // deprecated -- remove #define CH6_HELI_EXTERNAL_GYRO 13 // TradHeli specific external tail gyro gain #define CH6_OPTFLOW_KP 17 // deprecated -- remove #define CH6_OPTFLOW_KI 18 // deprecated -- remove #define CH6_OPTFLOW_KD 19 // deprecated -- remove #define CH6_AHRS_YAW_KP 30 // ahrs's compass effect on yaw angle (0 = very low, 1 = very high) #define CH6_AHRS_KP 31 // accelerometer effect on roll/pitch angle (0=low) #define CH6_INAV_TC 32 // deprecated -- remove #define CH6_DECLINATION 38 // compass declination in radians #define CH6_CIRCLE_RATE 39 // circle turn rate in degrees (hard coded to about 45 degrees in either direction) #define CH6_SONAR_GAIN 41 // sonar gain #define CH6_EKF_VERTICAL_POS 42 // EKF's baro vs accel (higher rely on accels more, baro impact is reduced). Range should be 0.2 ~ 4.0? 2.0 is default #define CH6_EKF_HORIZONTAL_POS 43 // EKF's gps vs accel (higher rely on accels more, gps impact is reduced). Range should be 1.0 ~ 3.0? 1.5 is default #define CH6_EKF_ACCEL_NOISE 44 // EKF's accel noise (lower means trust accels more, gps & baro less). Range should be 0.02 ~ 0.5 0.5 is default (but very robust at that level) #define CH6_RC_FEEL_RP 45 // roll-pitch input smoothing #define CH6_RATE_PITCH_KP 46 // body frame pitch rate controller's P term #define CH6_RATE_PITCH_KI 47 // body frame pitch rate controller's I term #define CH6_RATE_PITCH_KD 48 // body frame pitch rate controller's D term #define CH6_RATE_ROLL_KP 49 // body frame roll rate controller's P term #define CH6_RATE_ROLL_KI 50 // body frame roll rate controller's I term #define CH6_RATE_ROLL_KD 51 // body frame roll rate controller's D term #define CH6_RATE_PITCH_FF 52 // body frame pitch rate controller FF term #define CH6_RATE_ROLL_FF 53 // body frame roll rate controller FF term #define CH6_RATE_YAW_FF 54 // body frame yaw rate controller FF term // Acro Trainer types #define ACRO_TRAINER_DISABLED 0 #define ACRO_TRAINER_LEVELING 1 #define ACRO_TRAINER_LIMITED 2 // RC Feel roll/pitch definitions #define RC_FEEL_RP_VERY_SOFT 0 #define RC_FEEL_RP_SOFT 25 #define RC_FEEL_RP_MEDIUM 50 #define RC_FEEL_RP_CRISP 75 #define RC_FEEL_RP_VERY_CRISP 100 // Yaw behaviours during missions - possible values for WP_YAW_BEHAVIOR parameter #define WP_YAW_BEHAVIOR_NONE 0 // auto pilot will never control yaw during missions or rtl (except for DO_CONDITIONAL_YAW command received) #define WP_YAW_BEHAVIOR_LOOK_AT_NEXT_WP 1 // auto pilot will face next waypoint or home during rtl #define WP_YAW_BEHAVIOR_LOOK_AT_NEXT_WP_EXCEPT_RTL 2 // auto pilot will face next waypoint except when doing RTL at which time it will stay in it's last #define WP_YAW_BEHAVIOR_LOOK_AHEAD 3 // auto pilot will look ahead during missions and rtl (primarily meant for traditional helicotpers) // Auto modes enum AutoMode { Auto_TakeOff, Auto_WP, Auto_Land, Auto_RTL, Auto_CircleMoveToEdge, Auto_Circle, Auto_Spline, Auto_NavGuided, Auto_Loiter }; // Guided modes enum GuidedMode { Guided_TakeOff, Guided_WP, Guided_Velocity, Guided_Spline }; // RTL states enum RTLState { InitialClimb, ReturnHome, LoiterAtHome, FinalDescent, Land }; // Flip states enum FlipState { Flip_Start, Flip_Roll, Flip_Pitch_A, Flip_Pitch_B, Flip_Recover, Flip_Abandon }; // LAND state #define LAND_STATE_FLY_TO_LOCATION 0 #define LAND_STATE_DESCENDING 1 // Logging parameters #define TYPE_AIRSTART_MSG 0x00 #define TYPE_GROUNDSTART_MSG 0x01 #define LOG_ATTITUDE_MSG 0x01 #define LOG_MODE_MSG 0x03 #define LOG_CONTROL_TUNING_MSG 0x04 #define LOG_NAV_TUNING_MSG 0x05 #define LOG_PERFORMANCE_MSG 0x06 #define LOG_CURRENT_MSG 0x09 #define LOG_STARTUP_MSG 0x0A #define LOG_OPTFLOW_MSG 0x0C #define LOG_EVENT_MSG 0x0D #define LOG_PID_MSG 0x0E // deprecated #define LOG_COMPASS_MSG 0x0F #define LOG_INAV_MSG 0x11 // deprecated #define LOG_CAMERA_MSG_DEPRECATED 0x12 // deprecated #define LOG_ERROR_MSG 0x13 #define LOG_DATA_INT16_MSG 0x14 #define LOG_DATA_UINT16_MSG 0x15 #define LOG_DATA_INT32_MSG 0x16 #define LOG_DATA_UINT32_MSG 0x17 #define LOG_DATA_FLOAT_MSG 0x18 #define LOG_AUTOTUNE_MSG 0x19 #define LOG_AUTOTUNEDETAILS_MSG 0x1A #define LOG_COMPASS2_MSG 0x1B #define LOG_COMPASS3_MSG 0x1C #define MASK_LOG_ATTITUDE_FAST (1<<0) #define MASK_LOG_ATTITUDE_MED (1<<1) #define MASK_LOG_GPS (1<<2) #define MASK_LOG_PM (1<<3) #define MASK_LOG_CTUN (1<<4) #define MASK_LOG_NTUN (1<<5) #define MASK_LOG_RCIN (1<<6) #define MASK_LOG_IMU (1<<7) #define MASK_LOG_CMD (1<<8) #define MASK_LOG_CURRENT (1<<9) #define MASK_LOG_RCOUT (1<<10) #define MASK_LOG_OPTFLOW (1<<11) #define MASK_LOG_PID (1<<12) // deprecated #define MASK_LOG_COMPASS (1<<13) #define MASK_LOG_INAV (1<<14) // deprecated #define MASK_LOG_CAMERA (1<<15) #define MASK_LOG_WHEN_DISARMED (1UL<<16) #define MASK_LOG_ANY 0xFFFF // DATA - event logging #define DATA_MAVLINK_FLOAT 1 #define DATA_MAVLINK_INT32 2 #define DATA_MAVLINK_INT16 3 #define DATA_MAVLINK_INT8 4 #define DATA_AP_STATE 7 #define DATA_INIT_SIMPLE_BEARING 9 #define DATA_ARMED 10 #define DATA_DISARMED 11 #define DATA_AUTO_ARMED 15 #define DATA_TAKEOFF 16 #define DATA_LAND_COMPLETE_MAYBE 17 #define DATA_LAND_COMPLETE 18 #define DATA_NOT_LANDED 28 #define DATA_LOST_GPS 19 #define DATA_FLIP_START 21 #define DATA_FLIP_END 22 #define DATA_SET_HOME 25 #define DATA_SET_SIMPLE_ON 26 #define DATA_SET_SIMPLE_OFF 27 #define DATA_SET_SUPERSIMPLE_ON 29 #define DATA_AUTOTUNE_INITIALISED 30 #define DATA_AUTOTUNE_OFF 31 #define DATA_AUTOTUNE_RESTART 32 #define DATA_AUTOTUNE_SUCCESS 33 #define DATA_AUTOTUNE_FAILED 34 #define DATA_AUTOTUNE_REACHED_LIMIT 35 #define DATA_AUTOTUNE_PILOT_TESTING 36 #define DATA_AUTOTUNE_SAVEDGAINS 37 #define DATA_SAVE_TRIM 38 #define DATA_SAVEWP_ADD_WP 39 #define DATA_SAVEWP_CLEAR_MISSION_RTL 40 #define DATA_FENCE_ENABLE 41 #define DATA_FENCE_DISABLE 42 #define DATA_ACRO_TRAINER_DISABLED 43 #define DATA_ACRO_TRAINER_LEVELING 44 #define DATA_ACRO_TRAINER_LIMITED 45 #define DATA_EPM_GRAB 46 #define DATA_EPM_RELEASE 47 #define DATA_EPM_NEUTRAL 48 // deprecated #define DATA_PARACHUTE_DISABLED 49 #define DATA_PARACHUTE_ENABLED 50 #define DATA_PARACHUTE_RELEASED 51 // Centi-degrees to radians #define DEGX100 5729.57795f // mark a function as not to be inlined #define NOINLINE __attribute__((noinline)) // Error message sub systems and error codes #define ERROR_SUBSYSTEM_MAIN 1 #define ERROR_SUBSYSTEM_RADIO 2 #define ERROR_SUBSYSTEM_COMPASS 3 #define ERROR_SUBSYSTEM_OPTFLOW 4 #define ERROR_SUBSYSTEM_FAILSAFE_RADIO 5 #define ERROR_SUBSYSTEM_FAILSAFE_BATT 6 #define ERROR_SUBSYSTEM_FAILSAFE_GPS 7 #define ERROR_SUBSYSTEM_FAILSAFE_GCS 8 #define ERROR_SUBSYSTEM_FAILSAFE_FENCE 9 #define ERROR_SUBSYSTEM_FLIGHT_MODE 10 #define ERROR_SUBSYSTEM_GPS 11 #define ERROR_SUBSYSTEM_CRASH_CHECK 12 #define ERROR_SUBSYSTEM_FLIP 13 #define ERROR_SUBSYSTEM_AUTOTUNE 14 #define ERROR_SUBSYSTEM_PARACHUTE 15 #define ERROR_SUBSYSTEM_EKFINAV_CHECK 16 #define ERROR_SUBSYSTEM_FAILSAFE_EKFINAV 17 #define ERROR_SUBSYSTEM_BARO 18 #define ERROR_SUBSYSTEM_CPU 19 // general error codes #define ERROR_CODE_ERROR_RESOLVED 0 #define ERROR_CODE_FAILED_TO_INITIALISE 1 // subsystem specific error codes -- radio #define ERROR_CODE_RADIO_LATE_FRAME 2 // subsystem specific error codes -- failsafe_thr, batt, gps #define ERROR_CODE_FAILSAFE_RESOLVED 0 #define ERROR_CODE_FAILSAFE_OCCURRED 1 // subsystem specific error codes -- compass #define ERROR_CODE_COMPASS_FAILED_TO_READ 2 // subsystem specific error codes -- gps #define ERROR_CODE_GPS_GLITCH 2 // subsystem specific error codes -- main #define ERROR_CODE_MAIN_INS_DELAY 1 // subsystem specific error codes -- crash checker #define ERROR_CODE_CRASH_CHECK_CRASH 1 #define ERROR_CODE_CRASH_CHECK_LOSS_OF_CONTROL 2 // subsystem specific error codes -- flip #define ERROR_CODE_FLIP_ABANDONED 2 // subsystem specific error codes -- autotune #define ERROR_CODE_AUTOTUNE_BAD_GAINS 2 // parachute failed to deploy because of low altitude #define ERROR_CODE_PARACHUTE_TOO_LOW 2 // EKF check definitions #define ERROR_CODE_EKFINAV_CHECK_BAD_VARIANCE 2 #define ERROR_CODE_EKFINAV_CHECK_VARIANCE_CLEARED 0 // Baro specific error codes #define ERROR_CODE_BARO_GLITCH 2 // Arming Check Enable/Disable bits #define ARMING_CHECK_NONE 0x00 #define ARMING_CHECK_ALL 0x01 #define ARMING_CHECK_BARO 0x02 #define ARMING_CHECK_COMPASS 0x04 #define ARMING_CHECK_GPS 0x08 #define ARMING_CHECK_INS 0x10 #define ARMING_CHECK_PARAMETERS 0x20 #define ARMING_CHECK_RC 0x40 #define ARMING_CHECK_VOLTAGE 0x80 // Radio failsafe definitions (FS_THR parameter) #define FS_THR_DISABLED 0 #define FS_THR_ENABLED_ALWAYS_RTL 1 #define FS_THR_ENABLED_CONTINUE_MISSION 2 #define FS_THR_ENABLED_ALWAYS_LAND 3 // Battery failsafe definitions (FS_BATT_ENABLE parameter) #define FS_BATT_DISABLED 0 // battery failsafe disabled #define FS_BATT_LAND 1 // switch to LAND mode on battery failsafe #define FS_BATT_RTL 2 // switch to RTL mode on battery failsafe // GPS Failsafe definitions (FS_GPS_ENABLE parameter) #define FS_GPS_DISABLED 0 // GPS failsafe disabled #define FS_GPS_LAND 1 // switch to LAND mode on GPS Failsafe #define FS_GPS_ALTHOLD 2 // switch to ALTHOLD mode on GPS failsafe #define FS_GPS_LAND_EVEN_STABILIZE 3 // switch to LAND mode on GPS failsafe even if in a manual flight mode like Stabilize // for mavlink SET_POSITION_TARGET messages #define MAVLINK_SET_POS_TYPE_MASK_POS_IGNORE ((1<<0) | (1<<1) | (1<<2)) #define MAVLINK_SET_POS_TYPE_MASK_VEL_IGNORE ((1<<3) | (1<<4) | (1<<5)) #define MAVLINK_SET_POS_TYPE_MASK_ACC_IGNORE ((1<<6) | (1<<7) | (1<<8)) #define MAVLINK_SET_POS_TYPE_MASK_FORCE (1<<10) #define MAVLINK_SET_POS_TYPE_MASK_YAW_IGNORE (1<<11) #define MAVLINK_SET_POS_TYPE_MASK_YAW_RATE_IGNORE (1<<12) enum Serial2Protocol { SERIAL2_MAVLINK = 1, SERIAL2_FRSKY_DPORT = 2, SERIAL2_FRSKY_SPORT = 3 // not supported yet }; #endif // _DEFINES_H