// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-

#if CLI_ENABLED == ENABLED

// Functions called from the setup menu
static int8_t	setup_radio				(uint8_t argc, const Menu::arg *argv);
static int8_t	setup_motors			(uint8_t argc, const Menu::arg *argv);
static int8_t	setup_accel				(uint8_t argc, const Menu::arg *argv);
static int8_t	setup_frame				(uint8_t argc, const Menu::arg *argv);
static int8_t	setup_factory			(uint8_t argc, const Menu::arg *argv);
static int8_t	setup_erase				(uint8_t argc, const Menu::arg *argv);
static int8_t	setup_flightmodes		(uint8_t argc, const Menu::arg *argv);
static int8_t	setup_batt_monitor		(uint8_t argc, const Menu::arg *argv);
static int8_t	setup_sonar				(uint8_t argc, const Menu::arg *argv);
static int8_t	setup_compass			(uint8_t argc, const Menu::arg *argv);
static int8_t	setup_tune				(uint8_t argc, const Menu::arg *argv);
static int8_t	setup_range				(uint8_t argc, const Menu::arg *argv);
//static int8_t	setup_mag_offset		(uint8_t argc, const Menu::arg *argv);
static int8_t	setup_declination		(uint8_t argc, const Menu::arg *argv);
static int8_t	setup_optflow			(uint8_t argc, const Menu::arg *argv);
static int8_t	setup_show				(uint8_t argc, const Menu::arg *argv);

#if FRAME_CONFIG == HELI_FRAME
	static int8_t	setup_heli				(uint8_t argc, const Menu::arg *argv);
	static int8_t	setup_gyro				(uint8_t argc, const Menu::arg *argv);
#endif

// Command/function table for the setup menu
const struct Menu::command setup_menu_commands[] PROGMEM = {
	// command			function called
	// =======        	===============
	{"erase", 			setup_erase},
	{"reset", 			setup_factory},
	{"radio",			setup_radio},
	{"frame",			setup_frame},
	{"motors",			setup_motors},
	{"level",			setup_accel},
	{"modes",			setup_flightmodes},
	{"battery",			setup_batt_monitor},
	{"sonar",			setup_sonar},
	{"compass",			setup_compass},
	{"tune",			setup_tune},
	{"range",			setup_range},
//	{"offsets",			setup_mag_offset},
	{"declination",		setup_declination},
	{"optflow",			setup_optflow},
#if FRAME_CONFIG == HELI_FRAME
	{"heli",			setup_heli},
	{"gyro",			setup_gyro},
#endif
	{"show",			setup_show}
};

// Create the setup menu object.
MENU(setup_menu, "setup", setup_menu_commands);

// Called from the top-level menu to run the setup menu.
static int8_t
setup_mode(uint8_t argc, const Menu::arg *argv)
{
	// Give the user some guidance
	Serial.printf_P(PSTR("Setup Mode\n\n\n"));
						 //"\n"
						 //"IMPORTANT: if you have not previously set this system up, use the\n"
						 //"'reset' command to initialize the EEPROM to sensible default values\n"
						 //"and then the 'radio' command to configure for your radio.\n"
						 //"\n"));

	if(g.rc_1.radio_min >= 1300){
		delay(1000);
		Serial.printf_P(PSTR("\n!Warning, radio not configured!"));
		delay(1000);
		Serial.printf_P(PSTR("\n Type 'radio' now.\n\n"));
	}

	// Run the setup menu.  When the menu exits, we will return to the main menu.
	setup_menu.run();
    return 0;
}

// Print the current configuration.
// Called by the setup menu 'show' command.
static int8_t
setup_show(uint8_t argc, const Menu::arg *argv)
{
	// clear the area
	print_blanks(8);

	report_version();
	report_radio();
	report_frame();
	report_batt_monitor();
	report_sonar();
	//report_gains();
	//report_xtrack();
	//report_throttle();
	report_flight_modes();
	report_imu();
	report_compass();
	report_optflow();

#if FRAME_CONFIG == HELI_FRAME
	report_heli();
	report_gyro();
#endif

    AP_Param::show_all();

	return(0);
}

// Initialise the EEPROM to 'factory' settings (mostly defined in APM_Config.h or via defaults).
// Called by the setup menu 'factoryreset' command.
static int8_t
setup_factory(uint8_t argc, const Menu::arg *argv)
{
	int c;

	Serial.printf_P(PSTR("\n'Y' = factory reset, any other key to abort:\n"));

	do {
		c = Serial.read();
	} while (-1 == c);

	if (('y' != c) && ('Y' != c))
		return(-1);

	AP_Param::erase_all();
	Serial.printf_P(PSTR("\nReboot APM"));

	delay(1000);
	//default_gains();

	for (;;) {
	}
	// note, cannot actually return here
	return(0);
}

// Perform radio setup.
// Called by the setup menu 'radio' command.
static int8_t
setup_radio(uint8_t argc, const Menu::arg *argv)
{
	Serial.println("\n\nRadio Setup:");
	uint8_t i;

	for(i = 0; i < 100;i++){
		delay(20);
		read_radio();
	}

	if(g.rc_1.radio_in < 500){
		while(1){
			//Serial.printf_P(PSTR("\nNo radio; Check connectors."));
			delay(1000);
			// stop here
		}
	}

	g.rc_1.radio_min = g.rc_1.radio_in;
	g.rc_2.radio_min = g.rc_2.radio_in;
	g.rc_3.radio_min = g.rc_3.radio_in;
	g.rc_4.radio_min = g.rc_4.radio_in;
	g.rc_5.radio_min = g.rc_5.radio_in;
	g.rc_6.radio_min = g.rc_6.radio_in;
	g.rc_7.radio_min = g.rc_7.radio_in;
	g.rc_8.radio_min = g.rc_8.radio_in;

	g.rc_1.radio_max = g.rc_1.radio_in;
	g.rc_2.radio_max = g.rc_2.radio_in;
	g.rc_3.radio_max = g.rc_3.radio_in;
	g.rc_4.radio_max = g.rc_4.radio_in;
	g.rc_5.radio_max = g.rc_5.radio_in;
	g.rc_6.radio_max = g.rc_6.radio_in;
	g.rc_7.radio_max = g.rc_7.radio_in;
	g.rc_8.radio_max = g.rc_8.radio_in;

	g.rc_1.radio_trim = g.rc_1.radio_in;
	g.rc_2.radio_trim = g.rc_2.radio_in;
	g.rc_4.radio_trim = g.rc_4.radio_in;
	// 3 is not trimed
	g.rc_5.radio_trim = 1500;
	g.rc_6.radio_trim = 1500;
	g.rc_7.radio_trim = 1500;
	g.rc_8.radio_trim = 1500;


	Serial.printf_P(PSTR("\nMove all controls to extremes. Enter to save: "));
	while(1){

		delay(20);
		// Filters radio input - adjust filters in the radio.pde file
		// ----------------------------------------------------------
		read_radio();

		g.rc_1.update_min_max();
		g.rc_2.update_min_max();
		g.rc_3.update_min_max();
		g.rc_4.update_min_max();
		g.rc_5.update_min_max();
		g.rc_6.update_min_max();
		g.rc_7.update_min_max();
		g.rc_8.update_min_max();

		if(Serial.available() > 0){
			delay(20);
			Serial.flush();

			g.rc_1.save_eeprom();
			g.rc_2.save_eeprom();
			g.rc_3.save_eeprom();
			g.rc_4.save_eeprom();
			g.rc_5.save_eeprom();
			g.rc_6.save_eeprom();
			g.rc_7.save_eeprom();
			g.rc_8.save_eeprom();

			print_done();
			break;
		}
	}
	report_radio();
	return(0);
}

static int8_t
setup_motors(uint8_t argc, const Menu::arg *argv)
{
  Serial.printf_P(PSTR(
        "Now connect the main lipo and follow the instruction on the wiki for your frame setup.\n"
        "For security remember to disconnect the main lipo after the test, then hit any key to exit.\n"
        "Any key to exit.\n"));
	while(1){
		delay(20);
		read_radio();
		motors.output_test();
		if(Serial.available() > 0){
			g.esc_calibrate.set_and_save(0);
			return(0);
		}
	}
}

static int8_t
setup_accel(uint8_t argc, const Menu::arg *argv)
{
    imu.init(IMU::COLD_START, delay, flash_leds, &timer_scheduler);
	imu.init_accel(delay, flash_leds);
	print_accel_offsets();
	report_imu();
	return(0);
}

static int8_t
setup_frame(uint8_t argc, const Menu::arg *argv)
{
	if (!strcmp_P(argv[1].str, PSTR("x"))) {
		g.frame_orientation.set_and_save(X_FRAME);
	} else if (!strcmp_P(argv[1].str, PSTR("p"))) {
		g.frame_orientation.set_and_save(PLUS_FRAME);
	} else if (!strcmp_P(argv[1].str, PSTR("+"))) {
		g.frame_orientation.set_and_save(PLUS_FRAME);
	} else if (!strcmp_P(argv[1].str, PSTR("v"))) {
		g.frame_orientation.set_and_save(V_FRAME);
	}else{
		Serial.printf_P(PSTR("\nOp:[x,+,v]\n"));
		report_frame();
		return 0;
	}

	report_frame();
	return 0;
}

static int8_t
setup_flightmodes(uint8_t argc, const Menu::arg *argv)
{
	byte _switchPosition = 0;
	byte _oldSwitchPosition = 0;
	int8_t mode = 0;

	Serial.printf_P(PSTR("\nMode switch to edit, aileron: select modes, rudder: Simple on/off\n"));
	print_hit_enter();

	while(1){
		delay(20);
		read_radio();
		_switchPosition = readSwitch();


		// look for control switch change
		if (_oldSwitchPosition != _switchPosition){

			mode = flight_modes[_switchPosition];
			mode = constrain(mode, 0, NUM_MODES-1);

			// update the user
			print_switch(_switchPosition, mode, (g.simple_modes & (1<<_switchPosition)));

			// Remember switch position
			_oldSwitchPosition = _switchPosition;
		}

		// look for stick input
		if (abs(g.rc_1.control_in) > 3000){
			mode++;
			if(mode >= NUM_MODES)
				mode = 0;

			// save new mode
			flight_modes[_switchPosition] = mode;

			// print new mode
			print_switch(_switchPosition, mode, (g.simple_modes & (1<<_switchPosition)));
			delay(500);
		}

		// look for stick input
		if (g.rc_4.control_in > 3000){
			g.simple_modes |= (1<<_switchPosition);
			// print new mode
			print_switch(_switchPosition, mode, (g.simple_modes & (1<<_switchPosition)));
			delay(500);
		}

		// look for stick input
		if (g.rc_4.control_in < -3000){
			g.simple_modes &= ~(1<<_switchPosition);
			// print new mode
			print_switch(_switchPosition, mode, (g.simple_modes & (1<<_switchPosition)));
			delay(500);
		}

		// escape hatch
		if(Serial.available() > 0){
			for (mode = 0; mode < 6; mode++)
                flight_modes[mode].save();

			g.simple_modes.save();
			print_done();
			report_flight_modes();
			return (0);
		}
	}
}

static int8_t
setup_declination(uint8_t argc, const Menu::arg *argv)
{
	compass.set_declination(radians(argv[1].f));
	report_compass();
	return 0;
}

static int8_t
setup_tune(uint8_t argc, const Menu::arg *argv)
{
	g.radio_tuning.set_and_save(argv[1].i);
	//g.radio_tuning_high.set_and_save(1000);
	//g.radio_tuning_low.set_and_save(0);
	report_tuning();
	return 0;
}

static int8_t
setup_range(uint8_t argc, const Menu::arg *argv)
{
	Serial.printf_P(PSTR("\nCH 6 Ranges are divided by 1000: [low, high]\n"));

	g.radio_tuning_low.set_and_save(argv[1].i);
	g.radio_tuning_high.set_and_save(argv[2].i);
	report_tuning();
	return 0;
}



static int8_t
setup_erase(uint8_t argc, const Menu::arg *argv)
{
	zero_eeprom();
	return 0;
}

static int8_t
setup_compass(uint8_t argc, const Menu::arg *argv)
{
	if (!strcmp_P(argv[1].str, PSTR("on"))) {
		g.compass_enabled.set_and_save(true);
		init_compass();

	} else if (!strcmp_P(argv[1].str, PSTR("off"))) {
		clear_offsets();
		g.compass_enabled.set_and_save(false);

	}else{
		Serial.printf_P(PSTR("\nOp:[on,off]\n"));
		report_compass();
		return 0;
	}

	g.compass_enabled.save();
	report_compass();
	return 0;
}

static int8_t
setup_batt_monitor(uint8_t argc, const Menu::arg *argv)
{
	if (!strcmp_P(argv[1].str, PSTR("off"))) {
		g.battery_monitoring.set_and_save(0);

	} else if(argv[1].i > 0 && argv[1].i <= 4){
		g.battery_monitoring.set_and_save(argv[1].i);

	} else {
		Serial.printf_P(PSTR("\nOp: off, 3-4"));
	}

	report_batt_monitor();
	return 0;
}

static int8_t
setup_sonar(uint8_t argc, const Menu::arg *argv)
{
	if (!strcmp_P(argv[1].str, PSTR("on"))) {
		g.sonar_enabled.set_and_save(true);

	} else if (!strcmp_P(argv[1].str, PSTR("off"))) {
		g.sonar_enabled.set_and_save(false);

	} else if (argc > 1 && (argv[1].i >= 0 && argv[1].i <= 2)) {
	    g.sonar_enabled.set_and_save(true);  // if you set the sonar type, surely you want it on
		g.sonar_type.set_and_save(argv[1].i);

	}else{
		Serial.printf_P(PSTR("\nOp:[on, off, 0-2]\n"));
		report_sonar();
		return 0;
	}

	report_sonar();
	return 0;
}

#if FRAME_CONFIG == HELI_FRAME

// Perform heli setup.
// Called by the setup menu 'radio' command.
static int8_t
setup_heli(uint8_t argc, const Menu::arg *argv)
{

	uint8_t active_servo = 0;
	int value = 0;
	int temp;
	int state = 0;   // 0 = set rev+pos, 1 = capture min/max
	int max_roll=0, max_pitch=0, min_collective=0, max_collective=0, min_tail=0, max_tail=0;

	// initialise swash plate
	motors.init_swash();

	// source swash plate movements directly from radio
	motors.servo_manual = true;

	// display initial settings
	report_heli();

	// display help
	Serial.printf_P(PSTR("Instructions:"));
	print_divider();
	Serial.printf_P(PSTR("\td\t\tdisplay settings\n"));
	Serial.printf_P(PSTR("\t1~4\t\tselect servo\n"));
	Serial.printf_P(PSTR("\ta or z\t\tmove mid up/down\n"));
	Serial.printf_P(PSTR("\tc\t\tset coll when blade pitch zero\n"));
	Serial.printf_P(PSTR("\tm\t\tset roll, pitch, coll min/max\n"));
	Serial.printf_P(PSTR("\tp<angle>\tset pos (i.e. p0 = front, p90 = right)\n"));
	Serial.printf_P(PSTR("\tr\t\treverse servo\n"));
	Serial.printf_P(PSTR("\tu a|d\t\tupdate rate (a=analog servo, d=digital)\n"));
	Serial.printf_P(PSTR("\tt<angle>\tset trim (-500 ~ 500)\n"));
	Serial.printf_P(PSTR("\tx\t\texit & save\n"));

	// start capturing
	while( value != 'x' ) {

	    // read radio although we don't use it yet
	    read_radio();

		// allow swash plate to move
		motors.output_armed();

		// record min/max
		if( state == 1 ) {
		    if( abs(g.rc_1.control_in) > max_roll )
			    max_roll = abs(g.rc_1.control_in);
			if( abs(g.rc_2.control_in) > max_pitch )
			    max_pitch = abs(g.rc_2.control_in);
			if( g.rc_3.radio_out < min_collective )
			    min_collective = g.rc_3.radio_out;
			if( g.rc_3.radio_out > max_collective )
			    max_collective = g.rc_3.radio_out;
			min_tail = min(g.rc_4.radio_out, min_tail);
			max_tail = max(g.rc_4.radio_out, max_tail);
		}

	    if( Serial.available() ) {
		    value = Serial.read();

			// process the user's input
			switch( value ) {
				case '1':
					active_servo = CH_1;
					break;
				case '2':
					active_servo = CH_2;
					break;
				case '3':
					active_servo = CH_3;
					break;
				case '4':
					active_servo = CH_4;
					break;
				case 'a':
				case 'A':
					heli_get_servo(active_servo)->radio_trim += 10;
					break;
				case 'c':
				case 'C':
				    if( g.rc_3.radio_out >= 900 && g.rc_3.radio_out <= 2100 ) {
						motors.collective_mid = g.rc_3.radio_out;
						Serial.printf_P(PSTR("Collective when blade pitch at zero: %d\n"),(int)motors.collective_mid);
					}
					break;
				case 'd':
				case 'D':
					// display settings
					report_heli();
					break;
				case 'm':
				case 'M':
				    if( state == 0 ) {
					    state = 1;  // switch to capture min/max mode
						Serial.printf_P(PSTR("Move coll, roll, pitch and tail to extremes, press 'm' when done\n"));

						// reset servo ranges
						motors.roll_max = motors.pitch_max = 4500;
						motors.collective_min = 1000;
						motors.collective_max = 2000;
						motors._servo_4->radio_min = 1000;
						motors._servo_4->radio_max = 2000;

						// set sensible values in temp variables
						max_roll = abs(g.rc_1.control_in);
						max_pitch = abs(g.rc_2.control_in);
						min_collective = 2000;
						max_collective = 1000;
						min_tail = max_tail = abs(g.rc_4.radio_out);
					}else{
					    state = 0;  // switch back to normal mode
						// double check values aren't totally terrible
						if( max_roll <= 1000 || max_pitch <= 1000 || (max_collective - min_collective < 200) || (max_tail - min_tail < 200) || min_tail < 1000 || max_tail > 2000 )
						    Serial.printf_P(PSTR("Invalid min/max captured roll:%d,  pitch:%d,  collective min: %d max: %d,  tail min:%d max:%d\n"),max_roll,max_pitch,min_collective,max_collective,min_tail,max_tail);
						else{
						    motors.roll_max = max_roll;
							motors.pitch_max = max_pitch;
							motors.collective_min = min_collective;
							motors.collective_max = max_collective;
							motors._servo_4->radio_min = min_tail;
							motors._servo_4->radio_max = max_tail;

							// reinitialise swash
							motors.init_swash();

							// display settings
							report_heli();
						}
					}
					break;
				case 'p':
				case 'P':
					temp = read_num_from_serial();
					if( temp >= -360 && temp <= 360 ) {
						if( active_servo == CH_1 )
							motors.servo1_pos = temp;
						if( active_servo == CH_2 )
							motors.servo2_pos = temp;
						if( active_servo == CH_3 )
							motors.servo3_pos = temp;
						motors.init_swash();
						Serial.printf_P(PSTR("Servo %d\t\tpos:%d\n"),active_servo+1, temp);
					}
					break;
				case 'r':
				case 'R':
				    heli_get_servo(active_servo)->set_reverse(!heli_get_servo(active_servo)->get_reverse());
					break;
				case 't':
				case 'T':
					temp = read_num_from_serial();
					if( temp > 1000 )
					    temp -= 1500;
					if( temp > -500 && temp < 500 ) {
					    heli_get_servo(active_servo)->radio_trim = 1500 + temp;
						motors.init_swash();
						Serial.printf_P(PSTR("Servo %d\t\ttrim:%d\n"),active_servo+1, 1500 + temp);
					}
					break;
				case 'u':
				case 'U':
				    temp = 0;
					// delay up to 2 seconds for servo type from user
					while( !Serial.available() && temp < 20 ) {
					    temp++;
					    delay(100);
					}
					if( Serial.available() ) {
					    value = Serial.read();
						if( value == 'a' || value == 'A' ) {
							g.rc_speed.set_and_save(AP_MOTORS_HELI_SPEED_ANALOG_SERVOS);
							//motors._speed_hz = AP_MOTORS_HELI_SPEED_ANALOG_SERVOS;  // need to force this update to take effect immediately
							Serial.printf_P(PSTR("Analog Servo %dhz\n"),(int)g.rc_speed);
						}
						if( value == 'd' || value == 'D' ) {
							g.rc_speed.set_and_save(AP_MOTORS_HELI_SPEED_ANALOG_SERVOS);
							//motors._speed_hz = AP_MOTORS_HELI_SPEED_ANALOG_SERVOS;  // need to force this update to take effect immediately
							Serial.printf_P(PSTR("Digital Servo %dhz\n"),(int)g.rc_speed);
						}
					}
					break;
				case 'z':
				case 'Z':
					heli_get_servo(active_servo)->radio_trim -= 10;
					break;
			}
		}

		delay(20);
	}

	// display final settings
	report_heli();

	// save to eeprom
	motors._servo_1->save_eeprom();
	motors._servo_2->save_eeprom();
	motors._servo_3->save_eeprom();
	motors._servo_4->save_eeprom();
	motors.servo1_pos.save();
	motors.servo2_pos.save();
	motors.servo3_pos.save();
	motors.roll_max.save();
	motors.pitch_max.save();
	motors.collective_min.save();
	motors.collective_max.save();
	motors.collective_mid.save();

	// return swash plate movements to attitude controller
	motors.servo_manual = false;

	return(0);
}

// setup for external tail gyro (for heli only)
static int8_t
setup_gyro(uint8_t argc, const Menu::arg *argv)
{
	if (!strcmp_P(argv[1].str, PSTR("on"))) {
		motors.ext_gyro_enabled.set_and_save(true);

		// optionally capture the gain
		if( argc >= 2 && argv[2].i >= 1000 && argv[2].i <= 2000 ) {
		    motors.ext_gyro_gain = argv[2].i;
			motors.ext_gyro_gain.save();
		}

	} else if (!strcmp_P(argv[1].str, PSTR("off"))) {
		motors.ext_gyro_enabled.set_and_save(false);

    // capture gain if user simply provides a number
	} else if( argv[1].i >= 1000 && argv[1].i <= 2000 ) {
	    motors.ext_gyro_enabled.set_and_save(true);
		motors.ext_gyro_gain = argv[1].i;
		motors.ext_gyro_gain.save();

	}else{
		Serial.printf_P(PSTR("\nOp:[on, off] gain\n"));
	}

	report_gyro();
	return 0;
}

#endif // FRAME_CONFIG == HELI

static void clear_offsets()
{
	Vector3f _offsets(0.0,0.0,0.0);
	compass.set_offsets(_offsets);
	compass.save_offsets();
}

/*static int8_t
setup_mag_offset(uint8_t argc, const Menu::arg *argv)
{
	Vector3f _offsets;

	if (!strcmp_P(argv[1].str, PSTR("c"))) {
		clear_offsets();
		report_compass();
		return (0);
	}

	print_hit_enter();
	init_compass();

	int _min[3] = {0,0,0};
	int _max[3] = {0,0,0};

	compass.read();

	while(1){
		delay(50);
        float heading;

		compass.read();
		heading = compass.calculate_heading(0,0);	// roll = 0, pitch = 0

		if(compass.mag_x < _min[0])	_min[0] = compass.mag_x;
		if(compass.mag_y < _min[1])	_min[1] = compass.mag_y;
		if(compass.mag_z < _min[2])	_min[2] = compass.mag_z;

		// capture max
		if(compass.mag_x > _max[0])	_max[0] = compass.mag_x;
		if(compass.mag_y > _max[1])	_max[1] = compass.mag_y;
		if(compass.mag_z > _max[2])	_max[2] = compass.mag_z;

		// calculate offsets
		_offsets.x = (float)(_max[0] + _min[0]) / -2;
		_offsets.y = (float)(_max[1] + _min[1]) / -2;
		_offsets.z = (float)(_max[2] + _min[2]) / -2;

		// display all to user
		Serial.printf_P(PSTR("Heading: %u, \t (%d, %d, %d), (%4.4f, %4.4f, %4.4f)\n"),

				(uint16_t)(wrap_360(ToDeg(heading) * 100)) /100,

				compass.mag_x,
				compass.mag_y,
				compass.mag_z,

				_offsets.x,
				_offsets.y,
				_offsets.z);

		if(Serial.available() > 1){
			compass.set_offsets(_offsets);
			//compass.set_offsets(mag_offset_x, mag_offset_y, mag_offset_z);
			report_compass();
			return 0;
		}
	}
	return 0;
}
*/

static int8_t
setup_optflow(uint8_t argc, const Menu::arg *argv)
{
	#ifdef OPTFLOW_ENABLED
	if (!strcmp_P(argv[1].str, PSTR("on"))) {
		g.optflow_enabled = true;
		init_optflow();

	} else if (!strcmp_P(argv[1].str, PSTR("off"))) {
		g.optflow_enabled = false;

	}else{
		Serial.printf_P(PSTR("\nOp:[on, off]\n"));
		report_optflow();
		return 0;
	}

	g.optflow_enabled.save();
	report_optflow();
	#endif
	return 0;
}



/***************************************************************************/
// CLI reports
/***************************************************************************/

static void report_batt_monitor()
{
	Serial.printf_P(PSTR("\nBatt Mon:\n"));
	print_divider();
	if(g.battery_monitoring == 0)	print_enabled(false);
	if(g.battery_monitoring == 3)	Serial.printf_P(PSTR("volts"));
	if(g.battery_monitoring == 4)	Serial.printf_P(PSTR("volts and cur"));
	print_blanks(2);
}

static void report_wp(byte index = 255)
{
	if(index == 255){
		for(byte i = 0; i < g.command_total; i++){
			struct Location temp = get_cmd_with_index(i);
			print_wp(&temp, i);
		}
	}else{
		struct Location temp = get_cmd_with_index(index);
		print_wp(&temp, index);
	}
}

static void report_sonar()
{
	g.sonar_enabled.load();
	g.sonar_type.load();
	Serial.printf_P(PSTR("Sonar\n"));
	print_divider();
	print_enabled(g.sonar_enabled.get());
	Serial.printf_P(PSTR("Type: %d (0=XL, 1=LV, 2=XLL)"), (int)g.sonar_type);
	print_blanks(2);
}

static void report_frame()
{
	Serial.printf_P(PSTR("Frame\n"));
	print_divider();

#if FRAME_CONFIG == QUAD_FRAME
	Serial.printf_P(PSTR("Quad frame\n"));
#elif FRAME_CONFIG == TRI_FRAME
	Serial.printf_P(PSTR("TRI frame\n"));
#elif FRAME_CONFIG == HEXA_FRAME
	Serial.printf_P(PSTR("Hexa frame\n"));
#elif FRAME_CONFIG == Y6_FRAME
	Serial.printf_P(PSTR("Y6 frame\n"));
#elif FRAME_CONFIG == OCTA_FRAME
	Serial.printf_P(PSTR("Octa frame\n"));
#elif FRAME_CONFIG == HELI_FRAME
	Serial.printf_P(PSTR("Heli frame\n"));
#endif

#if FRAME_CONFIG != HELI_FRAME
	if(g.frame_orientation == X_FRAME)
		Serial.printf_P(PSTR("X mode\n"));
	else if(g.frame_orientation == PLUS_FRAME)
		Serial.printf_P(PSTR("+ mode\n"));
	else if(g.frame_orientation == V_FRAME)
		Serial.printf_P(PSTR("V mode\n"));
#endif

	print_blanks(2);
}

static void report_radio()
{
	Serial.printf_P(PSTR("Radio\n"));
	print_divider();
	// radio
	print_radio_values();
	print_blanks(2);
}

static void report_imu()
{
	Serial.printf_P(PSTR("IMU\n"));
	print_divider();

	print_gyro_offsets();
	print_accel_offsets();
	print_blanks(2);
}

static void report_compass()
{
	Serial.printf_P(PSTR("Compass\n"));
	print_divider();

	print_enabled(g.compass_enabled);

	// mag declination
	Serial.printf_P(PSTR("Mag Dec: %4.4f\n"),
							degrees(compass.get_declination()));

	Vector3f offsets = compass.get_offsets();

	// mag offsets
	Serial.printf_P(PSTR("Mag off: %4.4f, %4.4f, %4.4f"),
							offsets.x,
							offsets.y,
							offsets.z);
	print_blanks(2);
}

static void report_flight_modes()
{
	Serial.printf_P(PSTR("Flight modes\n"));
	print_divider();

	for(int i = 0; i < 6; i++ ){
		print_switch(i, flight_modes[i], (g.simple_modes & (1<<i)));
	}
	print_blanks(2);
}

void report_optflow()
{
	#ifdef OPTFLOW_ENABLED
	Serial.printf_P(PSTR("OptFlow\n"));
	print_divider();

	print_enabled(g.optflow_enabled);

	// field of view
	//Serial.printf_P(PSTR("FOV: %4.0f\n"),
	//						degrees(g.optflow_fov));

	print_blanks(2);
	#endif
}

#if FRAME_CONFIG == HELI_FRAME
static void report_heli()
{
	Serial.printf_P(PSTR("Heli\n"));
	print_divider();

	// main servo settings
	Serial.printf_P(PSTR("Servo \tpos \tmin \tmax \trev\n"));
	Serial.printf_P(PSTR("1:\t%d \t%d \t%d \t%d\n"),(int)motors.servo1_pos, (int)motors._servo_1->radio_min, (int)motors._servo_1->radio_max, (int)motors._servo_1->get_reverse());
	Serial.printf_P(PSTR("2:\t%d \t%d \t%d \t%d\n"),(int)motors.servo2_pos, (int)motors._servo_2->radio_min, (int)motors._servo_2->radio_max, (int)motors._servo_2->get_reverse());
	Serial.printf_P(PSTR("3:\t%d \t%d \t%d \t%d\n"),(int)motors.servo3_pos, (int)motors._servo_3->radio_min, (int)motors._servo_3->radio_max, (int)motors._servo_3->get_reverse());
	Serial.printf_P(PSTR("tail:\t\t%d \t%d \t%d\n"), (int)motors._servo_4->radio_min, (int)motors._servo_4->radio_max, (int)motors._servo_4->get_reverse());

	Serial.printf_P(PSTR("roll max: \t%d\n"), (int)motors.roll_max);
	Serial.printf_P(PSTR("pitch max: \t%d\n"), (int)motors.pitch_max);
	Serial.printf_P(PSTR("coll min:\t%d\t mid:%d\t max:%d\n"),(int)motors.collective_min, (int)motors.collective_mid, (int)motors.collective_max);

	// calculate and print servo rate
	Serial.printf_P(PSTR("servo rate:\t%d hz\n"),(int)g.rc_speed);

	print_blanks(2);
}

static void report_gyro()
{

	Serial.printf_P(PSTR("Gyro:\n"));
	print_divider();

	print_enabled( motors.ext_gyro_enabled );
	if( motors.ext_gyro_enabled )
	    Serial.printf_P(PSTR("gain: %d"),(int)motors.ext_gyro_gain);

	print_blanks(2);
}

#endif // FRAME_CONFIG == HELI_FRAME

/***************************************************************************/
// CLI utilities
/***************************************************************************/

/*static void
print_PID(PI * pid)
{
	Serial.printf_P(PSTR("P: %4.2f, I:%4.2f, IMAX:%ld\n"),
						pid->kP(),
						pid->kI(),
						(long)pid->imax());
}
*/

static void
print_radio_values()
{
	Serial.printf_P(PSTR("CH1: %d | %d\n"), (int)g.rc_1.radio_min, (int)g.rc_1.radio_max);
	Serial.printf_P(PSTR("CH2: %d | %d\n"), (int)g.rc_2.radio_min, (int)g.rc_2.radio_max);
	Serial.printf_P(PSTR("CH3: %d | %d\n"), (int)g.rc_3.radio_min, (int)g.rc_3.radio_max);
	Serial.printf_P(PSTR("CH4: %d | %d\n"), (int)g.rc_4.radio_min, (int)g.rc_4.radio_max);
	Serial.printf_P(PSTR("CH5: %d | %d\n"), (int)g.rc_5.radio_min, (int)g.rc_5.radio_max);
	Serial.printf_P(PSTR("CH6: %d | %d\n"), (int)g.rc_6.radio_min, (int)g.rc_6.radio_max);
	Serial.printf_P(PSTR("CH7: %d | %d\n"), (int)g.rc_7.radio_min, (int)g.rc_7.radio_max);
	//Serial.printf_P(PSTR("CH8: %d | %d\n"), (int)g.rc_8.radio_min, (int)g.rc_8.radio_max);
}

static void
print_switch(byte p, byte m, bool b)
{
	Serial.printf_P(PSTR("Pos %d:\t"),p);
	Serial.print(flight_mode_strings[m]);
	Serial.printf_P(PSTR(",\t\tSimple: "));
	if(b)
		Serial.printf_P(PSTR("ON\n"));
	else
		Serial.printf_P(PSTR("OFF\n"));
}

static void
print_done()
{
	Serial.printf_P(PSTR("\nSaved\n"));
}


static void zero_eeprom(void)
{
	byte b = 0;

	Serial.printf_P(PSTR("\nErasing EEPROM\n"));

	for (int i = 0; i < EEPROM_MAX_ADDR; i++) {
		eeprom_write_byte((uint8_t *) i, b);
	}

	Serial.printf_P(PSTR("done\n"));
}

static void
print_accel_offsets(void)
{
	Serial.printf_P(PSTR("A_off: %4.2f, %4.2f, %4.2f\n"),
						(float)imu.ax(),	// Pitch
						(float)imu.ay(),	// Roll
						(float)imu.az());	// YAW
}

static void
print_gyro_offsets(void)
{
	Serial.printf_P(PSTR("G_off: %4.2f, %4.2f, %4.2f\n"),
						(float)imu.gx(),
						(float)imu.gy(),
						(float)imu.gz());
}

#if FRAME_CONFIG == HELI_FRAME

static RC_Channel *
heli_get_servo(int servo_num){
	if( servo_num == CH_1 )
	    return motors._servo_1;
	if( servo_num == CH_2 )
	    return motors._servo_2;
	if( servo_num == CH_3 )
	    return motors._servo_3;
	if( servo_num == CH_4 )
	    return motors._servo_4;
	return NULL;
}

// Used to read integer values from the serial port
static int read_num_from_serial() {
	byte index = 0;
	byte timeout = 0;
	char data[5] = "";

	do {
		if (Serial.available() == 0) {
			delay(10);
			timeout++;
		}else{
			data[index] = Serial.read();
			timeout = 0;
			index++;
		}
	}while (timeout < 5 && index < 5);

	return atoi(data);
}
#endif

#endif // CLI_ENABLED

static void
print_blanks(int num)
{
	while(num > 0){
		num--;
		Serial.println("");
	}
}

static void
print_divider(void)
{
	for (int i = 0; i < 40; i++) {
		Serial.print("-");
	}
	Serial.println("");
}

static void print_enabled(boolean b)
{
	if(b)
		Serial.printf_P(PSTR("en"));
	else
		Serial.printf_P(PSTR("dis"));
	Serial.printf_P(PSTR("abled\n"));
}


static void
init_esc()
{
	motors.enable();
	motors.armed(true);
	while(1){
		read_radio();
		delay(100);
		dancing_light();
		motors.throttle_pass_through();
	}
}

static void print_wp(struct Location *cmd, byte index)
{
	float t1 = (float)cmd->lat / t7;
	float t2 = (float)cmd->lng / t7;

	Serial.printf_P(PSTR("cmd#: %d id:%d op:%d p1:%d p2:%ld p3:%4.7f p4:%4.7f \n"),
		(int)index,
		(int)cmd->id,
		(int)cmd->options,
		(int)cmd->p1,
		(long)cmd->alt,
		t1,
		t2);
}

static void report_gps()
{
	Serial.printf_P(PSTR("\nGPS\n"));
	print_divider();
	print_enabled(GPS_enabled);
	print_blanks(2);
}

static void report_version()
{
	Serial.printf_P(PSTR("FW Ver: %d\n"),(int)g.format_version.get());
#if QUATERNION_ENABLE == ENABLED
    Serial.printf_P(PSTR("Quaternion test\n"));
#endif
	print_divider();
	print_blanks(2);
}


static void report_tuning()
{
	Serial.printf_P(PSTR("\nTUNE:\n"));
	print_divider();
	if (g.radio_tuning == 0){
		print_enabled(g.radio_tuning.get());
	}else{
		float low  = (float)g.radio_tuning_low.get() / 1000;
		float high = (float)g.radio_tuning_high.get() / 1000;
		Serial.printf_P(PSTR(" %d, Low:%1.4f, High:%1.4f\n"),(int)g.radio_tuning.get(), low, high);
	}
	print_blanks(2);
}