// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*- void init_commands() { // zero is home, but we always load the next command (1), in the code. g.waypoint_index.set_and_save(0); // This are registers for the current may and must commands // setting to zero will allow them to be written to by new commands command_must_index = NO_COMMAND; command_may_index = NO_COMMAND; // clear the command queue clear_command_queue(); } void init_auto() { //if (g.waypoint_index == g.waypoint_total) { // Serial.println("ia_f"); // do_RTL(); //} // initialize commands // ------------------- init_commands(); } // forces the loading of a new command // queue is emptied after a new command is processed void clear_command_queue(){ next_command.id = NO_COMMAND; } // Getters // ------- struct Location get_command_with_index(int i) { struct Location temp; // Find out proper location in memory by using the start_byte position + the index // -------------------------------------------------------------------------------- if (i > g.waypoint_total) { Serial.println("XCD"); // we do not have a valid command to load // return a WP with a "Blank" id temp.id = CMD_BLANK; // no reason to carry on return temp; }else{ Serial.println("LD"); // we can load a command, we don't process it yet // read WP position long mem = (WP_START_BYTE) + (i * WP_SIZE); temp.id = eeprom_read_byte((uint8_t*)mem); mem++; temp.options = eeprom_read_byte((uint8_t*)mem); mem++; temp.p1 = eeprom_read_byte((uint8_t*)mem); mem++; temp.alt = (long)eeprom_read_dword((uint32_t*)mem); // alt is stored in CM! Alt is stored relative! mem += 4; temp.lat = (long)eeprom_read_dword((uint32_t*)mem); // lat is stored in decimal * 10,000,000 mem += 4; temp.lng = (long)eeprom_read_dword((uint32_t*)mem); // lon is stored in decimal * 10,000,000 } // Add on home altitude if we are a nav command (or other command with altitude) and stored alt is relative if((temp.id < MAV_CMD_NAV_LAST || temp.id == MAV_CMD_CONDITION_CHANGE_ALT) && temp.options & WP_OPTION_ALT_RELATIVE){ //temp.alt += home.alt; } Serial.println("ADD ALT"); if(temp.options & WP_OPTION_RELATIVE){ // If were relative, just offset from home temp.lat += home.lat; temp.lng += home.lng; } return temp; } // Setters // ------- void set_command_with_index(struct Location temp, int i) { i = constrain(i, 0, g.waypoint_total.get()); uint32_t mem = WP_START_BYTE + (i * WP_SIZE); eeprom_write_byte((uint8_t *) mem, temp.id); mem++; eeprom_write_byte((uint8_t *) mem, temp.options); mem++; eeprom_write_byte((uint8_t *) mem, temp.p1); mem++; eeprom_write_dword((uint32_t *) mem, temp.alt); // Alt is stored in CM! mem += 4; eeprom_write_dword((uint32_t *) mem, temp.lat); // Lat is stored in decimal degrees * 10^7 mem += 4; eeprom_write_dword((uint32_t *) mem, temp.lng); // Long is stored in decimal degrees * 10^7 } void increment_WP_index() { if (g.waypoint_index < g.waypoint_total) { g.waypoint_index.set_and_save(g.waypoint_index + 1); //SendDebug("MSG WP index is incremented to "); } SendDebugln(g.waypoint_index,DEC); } void decrement_WP_index() { if (g.waypoint_index > 0) { g.waypoint_index.set_and_save(g.waypoint_index - 1); } } long read_alt_to_hold() { if(g.RTL_altitude < 0) return current_loc.alt; else return g.RTL_altitude + home.alt; } //******************************************************************************** // This function sets the waypoint and modes for Return to Launch // It's not currently used //******************************************************************************** Location get_LOITER_home_wp() { //so we know where we are navigating from next_WP = current_loc; // read home position struct Location temp = get_command_with_index(0); // 0 = home temp.id = MAV_CMD_NAV_LOITER_UNLIM; temp.alt = read_alt_to_hold(); return temp; } /* This function sets the next waypoint command It precalculates all the necessary stuff. */ void set_next_WP(struct Location *wp) { SendDebug("MSG wp_index: "); SendDebugln(g.waypoint_index, DEC); gcs.send_message(MSG_COMMAND_LIST, g.waypoint_index); // copy the current WP into the OldWP slot // --------------------------------------- prev_WP = next_WP; // Load the next_WP slot // --------------------- next_WP = *wp; // used to control and limit the rate of climb - not used right now! // ----------------------------------------------------------------- target_altitude = current_loc.alt; // zero out our loiter vals to watch for missed waypoints //loiter_delta = 0; //loiter_sum = 0; //loiter_total = 0; // this is used to offset the shrinking longitude as we go towards the poles float rads = (abs(next_WP.lat)/t7) * 0.0174532925; scaleLongDown = cos(rads); scaleLongUp = 1.0f/cos(rads); // this is handy for the groundstation wp_totalDistance = get_distance(¤t_loc, &next_WP); // this makes the data not log for a GPS read wp_distance = wp_totalDistance; target_bearing = get_bearing(¤t_loc, &next_WP); nav_bearing = target_bearing; // to check if we have missed the WP // ---------------------------- saved_target_bearing = target_bearing; // set a new crosstrack bearing // ---------------------------- crosstrack_bearing = target_bearing; // Used for track following gcs.print_current_waypoints(); } // run this at setup on the ground // ------------------------------- void init_home() { SendDebugln("MSG: init home"); // block until we get a good fix // ----------------------------- while (!g_gps->new_data || !g_gps->fix) { g_gps->update(); } home.id = MAV_CMD_NAV_WAYPOINT; home.lng = g_gps->longitude; // Lon * 10**7 home.lat = g_gps->latitude; // Lat * 10**7 home.alt = max(g_gps->altitude, 0); // we sometimes get negatives from GPS, not valid home_is_set = true; // to point yaw towards home until we set it with Mavlink target_WP = home; //Serial.printf_P(PSTR("gps alt: %ld\n"), home.alt); // Save Home to EEPROM // ------------------- set_command_with_index(home, 0); print_wp(&home, 0); // Save prev loc this makes the calcs look better before commands are loaded next_WP = prev_WP = home; }