/// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: t -*- /* * ArduPlane parameter definitions * * This firmware is free software; you can redistribute it and/or * modify it under the terms of the GNU Lesser General Public * License as published by the Free Software Foundation; either * version 2.1 of the License, or (at your option) any later version. */ #define GSCALAR(v, name, def) { g.v.vtype, name, Parameters::k_param_ ## v, &g.v, {def_value : def} } #define GGROUP(v, name, class) { AP_PARAM_GROUP, name, Parameters::k_param_ ## v, &g.v, {group_info : class::var_info} } #define GOBJECT(v, name, class) { AP_PARAM_GROUP, name, Parameters::k_param_ ## v, &v, {group_info : class::var_info} } const AP_Param::Info var_info[] PROGMEM = { GSCALAR(format_version, "FORMAT_VERSION", 0), GSCALAR(software_type, "SYSID_SW_TYPE", Parameters::k_software_type), GSCALAR(sysid_this_mav, "SYSID_THISMAV", MAV_SYSTEM_ID), GSCALAR(sysid_my_gcs, "SYSID_MYGCS", 255), // @Param: SERIAL0_BAUD // @DisplayName: USB Console Baud Rate // @Description: The baud rate used on the main uart // @Values: 1:1200,2:2400,4:4800,9:9600,19:19200,38:38400,57:57600,111:111100,115:115200 // @User: Standard GSCALAR(serial0_baud, "SERIAL0_BAUD", SERIAL0_BAUD/1000), // @Param: SERIAL3_BAUD // @DisplayName: Telemetry Baud Rate // @Description: The baud rate used on the telemetry port // @Values: 1:1200,2:2400,4:4800,9:9600,19:19200,38:38400,57:57600,111:111100,115:115200 // @User: Standard GSCALAR(serial3_baud, "SERIAL3_BAUD", SERIAL3_BAUD/1000), // @Param: TELEM_DELAY // @DisplayName: Telemetry startup delay // @Description: The amount of time (in seconds) to delay radio telemetry to prevent an Xbee bricking on power up // @User: Standard // @Units: seconds // @Range: 0 10 // @Increment: 1 GSCALAR(telem_delay, "TELEM_DELAY", 0), // @Param: KFF_PTCHCOMP // @DisplayName: Pitch Compensation // @Description: Adds pitch input to compensate for the loss of lift due to roll control. 0 = 0 %, 1 = 100% // @Range: 0 1 // @Increment: 0.01 // @User: Advanced GSCALAR(kff_pitch_compensation, "KFF_PTCHCOMP", PITCH_COMP), // @Param: KFF_RDDRMIX // @DisplayName: Rudder Mix // @Description: The amount of rudder mix to apply during aileron movement 0 = 0 %, 1 = 100% // @Range: 0 1 // @Increment: 0.01 // @User: Standard GSCALAR(kff_rudder_mix, "KFF_RDDRMIX", RUDDER_MIX), // @Param: KFF_PTCH2THR // @DisplayName: Pitch to Throttle Mix // @Description: Pitch to throttle feed-forward gain. // @Range: 0 5 // @Increment: 0.01 // @User: Advanced GSCALAR(kff_pitch_to_throttle, "KFF_PTCH2THR", P_TO_T), // @Param: KFF_THR2PTCH // @DisplayName: Throttle to Pitch Mix // @Description: Throttle to pitch feed-forward gain. // @Range: 0 5 // @Increment: 0.01 // @User: Advanced GSCALAR(kff_throttle_to_pitch, "KFF_THR2PTCH", T_TO_P), // @Param: MANUAL_LEVEL // @DisplayName: Manual Level // @Description: Setting this to Disabled(0) will enable autolevel on every boot. Setting it to Enabled(1) will do a calibration only when you tell it to // @Values: 0:Disabled,1:Enabled // @User: Advanced GSCALAR(manual_level, "MANUAL_LEVEL", MANUAL_LEVEL), // @Param: STICK_MIXING // @DisplayName: Stick Mixing // @Description: When enabled, this adds user stick input to the control surfaces in auto modes, allowing the user to have some degree of flight control without changing modes // @Values: 0:Disabled,1:Enabled // @User: Advanced GSCALAR(stick_mixing, "STICK_MIXING", 1), // @Param: RUDDER_STEER // @DisplayName: Rudder steering on takeoff and landing // @Description: When enabled, only rudder will be used for steering during takeoff and landing, with the ailerons used to hold the plane level // @Values: 0:Disabled,1:Enabled // @User: User GSCALAR(rudder_steer, "RUDDER_STEER", 0), // @Param: land_pitch_cd // @DisplayName: Landing Pitch // @Description: Used in autoland for planes without airspeed sensors in hundredths of a degree // @Units: centi-Degrees // @User: Advanced GSCALAR(land_pitch_cd, "LAND_PITCH_CD", 0), // @Param: land_flare_alt // @DisplayName: Landing flare altitude // @Description: Altitude in autoland at which to lock heading and flare to the LAND_PITCH_CD pitch // @Units: meters // @Increment: 0.1 // @User: Advanced GSCALAR(land_flare_alt, "LAND_FLARE_ALT", 3.0), // @Param: land_flare_sec // @DisplayName: Landing flare time // @Description: Time before landing point at which to lock heading and flare to the LAND_PITCH_CD pitch // @Units: seconds // @Increment: 0.1 // @User: Advanced GSCALAR(land_flare_sec, "LAND_FLARE_SEC", 2.0), // @Param: XTRK_GAIN_SC // @DisplayName: Crosstrack Gain // @Description: The scale between distance off the line and angle to meet the line (in Degrees * 100) // @Range: 0 2000 // @Increment: 1 // @User: Standard GSCALAR(crosstrack_gain, "XTRK_GAIN_SC", XTRACK_GAIN_SCALED), // @Param: XTRK_ANGLE_CD // @DisplayName: Crosstrack Entry Angle // @Description: Maximum angle used to correct for track following. // @Units: centi-Degrees // @Range: 0 9000 // @Increment: 1 // @User: Standard GSCALAR(crosstrack_entry_angle, "XTRK_ANGLE_CD", XTRACK_ENTRY_ANGLE_CENTIDEGREE), // @Param: XTRK_USE_WIND // @DisplayName: Crosstrack Wind correction // @Description: If enabled, use wind estimation for navigation crosstrack when using a compass for yaw // @Values: 0:Disabled,1:Enabled // @User: Standard GSCALAR(crosstrack_use_wind, "XTRK_USE_WIND", 1), // @Param: XTRK_MIN_DIST // @DisplayName: Crosstrack mininum distance // @Description: Minimum distance in meters between waypoints to do crosstrack correction. // @Units: Meters // @Range: 0 32767 // @Increment: 1 // @User: Standard GSCALAR(crosstrack_min_distance, "XTRK_MIN_DIST", 50), // @Param: ALT_MIX // @DisplayName: Gps to Baro Mix // @Description: The percent of mixing between gps altitude and baro altitude. 0 = 100% gps, 1 = 100% baro // @Units: Percent // @Range: 0 1 // @Increment: 0.1 // @User: Advanced GSCALAR(altitude_mix, "ALT_MIX", ALTITUDE_MIX), // @Param: ALT_CTRL_ALG // @DisplayName: Altitude control algorithm // @Description: This sets what algorithm will be used for altitude control. The default is to select the algorithm based on whether airspeed is enabled. If you set it to 1, then the airspeed based algorithm won't be used for altitude control, but airspeed can be used for other flight control functions // @Values: 0:Default Method,1:non-airspeed // @User: Advanced GSCALAR(alt_control_algorithm, "ALT_CTRL_ALG", ALT_CONTROL_DEFAULT), // @Param: ALT_OFFSET // @DisplayName: Altitude offset // @Description: This is added to the target altitude in automatic flight. It can be used to add a global altitude offset to a mission, or to adjust for barometric pressure changes // @Units: Meters // @Range: -32767 32767 // @Increment: 1 // @User: Advanced GSCALAR(alt_offset, "ALT_OFFSET", 0), GSCALAR(command_total, "CMD_TOTAL", 0), GSCALAR(command_index, "CMD_INDEX", 0), // @Param: WP_RADIUS // @DisplayName: Waypoint Radius // @Description: Defines the distance from a waypoint, that when crossed indicates the wp has been hit. // @Units: Meters // @Range: 1 127 // @Increment: 1 // @User: Standard GSCALAR(waypoint_radius, "WP_RADIUS", WP_RADIUS_DEFAULT), // @Param: WP_LOITER_RAD // @DisplayName: Waypoint Loiter Radius // @Description: Defines the distance from the waypoint center, the plane will maintain during a loiter // @Units: Meters // @Range: 1 32767 // @Increment: 1 // @User: Standard GSCALAR(loiter_radius, "WP_LOITER_RAD", LOITER_RADIUS_DEFAULT), #if GEOFENCE_ENABLED == ENABLED // @Param: FENCE_ACTION // @DisplayName: Action on geofence breach // @Description: What to do on fence breach // @Values: 0:None,1:GuidedMode,2:ReportOnly // @User: Standard GSCALAR(fence_action, "FENCE_ACTION", 0), // @Param: FENCE_TOTAL // @DisplayName: Fence Total // @Description: Number of geofence points currently loaded // @User: Standard GSCALAR(fence_total, "FENCE_TOTAL", 0), // @Param: FENCE_CHANNEL // @DisplayName: Fence Channel // @Description: RC Channel to use to enable geofence. PWM input above 1750 enables the geofence // @User: Standard GSCALAR(fence_channel, "FENCE_CHANNEL", 0), // @Param: FENCE_MINALT // @DisplayName: Fence Minimum Altitude // @Description: Minimum altitude allowed before geofence triggers // @Units: meters // @Range: 0 32767 // @Increment: 1 // @User: Standard GSCALAR(fence_minalt, "FENCE_MINALT", 0), // @Param: FENCE_MAXALT // @DisplayName: Fence Maximum Altitude // @Description: Maximum altitude allowed before geofence triggers // @Units: meters // @Range: 0 32767 // @Increment: 1 // @User: Standard GSCALAR(fence_maxalt, "FENCE_MAXALT", 0), #endif // @Param: ARSPD_FBW_MIN // @DisplayName: Fly By Wire Minimum Airspeed // @Description: Airspeed corresponding to minimum throttle in Fly By Wire B mode. // @Units: m/s // @Range: 5 50 // @Increment: 1 // @User: Standard GSCALAR(flybywire_airspeed_min, "ARSPD_FBW_MIN", AIRSPEED_FBW_MIN), // @Param: ARSPD_FBW_MAX // @DisplayName: Fly By Wire Maximum Airspeed // @Description: Airspeed corresponding to maximum throttle in Fly By Wire B mode. // @Units: m/s // @Range: 5 50 // @Increment: 1 // @User: Standard GSCALAR(flybywire_airspeed_max, "ARSPD_FBW_MAX", AIRSPEED_FBW_MAX), // @Param: FBWB_ELEV_REV // @DisplayName: Fly By Wire elevator reverse // @Description: Reverse sense of elevator in FBWB. When set to 0 up elevator (pulling back on the stick) means to lower altitude. When set to 1, up elevator means to raise altitude. // @Values: 0:Disabled,1:Enabled // @User: Standard GSCALAR(flybywire_elev_reverse, "FBWB_ELEV_REV", 0), // @Param: THR_MIN // @DisplayName: Minimum Throttle // @Description: The minimum throttle setting to which the autopilot will apply. // @Units: Percent // @Range: 0 100 // @Increment: 1 // @User: Standard GSCALAR(throttle_min, "THR_MIN", THROTTLE_MIN), // @Param: THR_MAX // @DisplayName: Maximum Throttle // @Description: The maximum throttle setting to which the autopilot will apply. // @Units: Percent // @Range: 0 100 // @Increment: 1 // @User: Standard GSCALAR(throttle_max, "THR_MAX", THROTTLE_MAX), // @Param: THR_SLEWRATE // @DisplayName: Throttle slew rate // @Description: maximum percentage change in throttle per second. A setting of 10 means to not change the throttle by more than 10% of the full throttle range in one second // @Units: Percent // @Range: 0 100 // @Increment: 1 // @User: Standard GSCALAR(throttle_slewrate, "THR_SLEWRATE", THROTTLE_SLEW_LIMIT), // @Param: THR_SUPP_MAN // @DisplayName: Throttle suppress manual passthru // @Description: When throttle is supressed in auto mode it is normally forced to zero. If you enable this option, then while suppressed it will be manual throttle. This is useful on petrol engines to hold the idle throttle manually while waiting for takeoff // @Values: 0:Disabled,1:Enabled // @User: Advanced GSCALAR(throttle_suppress_manual,"THR_SUPP_MAN", 0), // @Param: THR_PASS_STAB // @DisplayName: Throttle passthru in stabilize // @Description: If this is set then when in STABILIZE or FBWA mode the throttle is a direct passthru from the transmitter. This means the THR_MIN and THR_MAX settings are not used in these modes. This is useful for petrol engines where you setup a throttle cut switch that suppresses the throttle below the normal minimum. // @Values: 0:Disabled,1:Enabled // @User: Advanced GSCALAR(throttle_passthru_stabilize,"THR_PASS_STAB", 0), // @Param: THR_FAILSAFE // @DisplayName: Throttle Failsafe Enable // @Description: The throttle failsafe allows you to configure a software failsafe activated by a setting on the throttle input channel // @Values: 0:Disabled,1:Enabled // @User: Standard GSCALAR(throttle_fs_enabled, "THR_FAILSAFE", THROTTLE_FAILSAFE), // @Param: THR_FS_VALUE // @DisplayName: Throttle Failsafe Value // @Description: The PWM level on channel 3 below which throttle sailsafe triggers // @User: Standard GSCALAR(throttle_fs_value, "THR_FS_VALUE", THROTTLE_FS_VALUE), // @Param: TRIM_THROTTLE // @DisplayName: Throttle cruise percentage // @Description: The target percentage of throttle to apply for normal flight // @Units: Percent // @Range: 0 100 // @Increment: 1 // @User: Standard GSCALAR(throttle_cruise, "TRIM_THROTTLE", THROTTLE_CRUISE), // @Param: THROTTLE_NUDGE // @DisplayName: Throttle nudge enable // @Description: When enabled, this uses the throttle input in auto-throttle modes to 'nudge' the throttle to higher or lower values // @Values: 0:Disabled,1:Enabled // @User: Standard // @User: Standard GSCALAR(throttle_nudge, "THROTTLE_NUDGE", 1), // @Param: FS_SHORT_ACTN // @DisplayName: Short failsafe action // @Description: The action to take on a short (1 second) failsafe event // @Values: 0:None,1:ReturnToLaunch // @User: Standard GSCALAR(short_fs_action, "FS_SHORT_ACTN", SHORT_FAILSAFE_ACTION), // @Param: FS_LONG_ACTN // @DisplayName: Long failsafe action // @Description: The action to take on a long (20 second) failsafe event // @Values: 0:None,1:ReturnToLaunch // @User: Standard GSCALAR(long_fs_action, "FS_LONG_ACTN", LONG_FAILSAFE_ACTION), // @Param: FS_GCS_ENABL // @DisplayName: GCS failsafe enable // @Description: Enable ground control station telemetry failsafe. Failsafe will trigger after 20 seconds of no MAVLink heartbeat messages. WARNING: Enabling this option opens up the possibility of your plane going into failsafe mode and running the motor on the ground it it loses contact with your ground station. If this option is enabled on an electric plane then either use a separate motor arming switch or remove the propeller in any ground testing. // @Values: 0:Disabled,1:Enabled // @User: Standard GSCALAR(gcs_heartbeat_fs_enabled, "FS_GCS_ENABL", GCS_HEARTBEAT_FAILSAFE), // @Param: FLTMODE_CH // @DisplayName: Flightmode channel // @Description: RC Channel to use for flight mode control // @User: Advanced GSCALAR(flight_mode_channel, "FLTMODE_CH", FLIGHT_MODE_CHANNEL), // @Param: FLTMODE1 // @DisplayName: FlightMode1 // @Values: 0:Manual,1:CIRCLE,2:STABILIZE,3:TRAINING,5:FBWA,6:FBWB,10:Auto,11:RTL,12:Loiter,15:Guided // @User: Standard // @Description: Flight mode for switch position 1 (910 to 1230 and above 2049) GSCALAR(flight_mode1, "FLTMODE1", FLIGHT_MODE_1), // @Param: FLTMODE2 // @DisplayName: FlightMode2 // @Description: Flight mode for switch position 2 (1231 to 1360) // @Values: 0:Manual,1:CIRCLE,2:STABILIZE,3:TRAINING,5:FBWA,6:FBWB,10:Auto,11:RTL,12:Loiter,15:Guided // @User: Standard GSCALAR(flight_mode2, "FLTMODE2", FLIGHT_MODE_2), // @Param: FLTMODE3 // @DisplayName: FlightMode3 // @Description: Flight mode for switch position 3 (1361 to 1490) // @Values: 0:Manual,1:CIRCLE,2:STABILIZE,3:TRAINING,5:FBWA,6:FBWB,10:Auto,11:RTL,12:Loiter,15:Guided // @User: Standard GSCALAR(flight_mode3, "FLTMODE3", FLIGHT_MODE_3), // @Param: FLTMODE4 // @DisplayName: FlightMode4 // @Description: Flight mode for switch position 4 (1491 to 1620) // @Values: 0:Manual,1:CIRCLE,2:STABILIZE,3:TRAINING,5:FBWA,6:FBWB,10:Auto,11:RTL,12:Loiter,15:Guided // @User: Standard GSCALAR(flight_mode4, "FLTMODE4", FLIGHT_MODE_4), // @Param: FLTMODE5 // @DisplayName: FlightMode5 // @Description: Flight mode for switch position 5 (1621 to 1749) // @Values: 0:Manual,1:CIRCLE,2:STABILIZE,3:TRAINING,5:FBWA,6:FBWB,10:Auto,11:RTL,12:Loiter,15:Guided // @User: Standard GSCALAR(flight_mode5, "FLTMODE5", FLIGHT_MODE_5), // @Param: FLTMODE6 // @DisplayName: FlightMode6 // @Description: Flight mode for switch position 6 (1750 to 2049) // @Values: 0:Manual,1:CIRCLE,2:STABILIZE,3:TRAINING,5:FBWA,6:FBWB,10:Auto,11:RTL,12:Loiter,15:Guided // @User: Standard GSCALAR(flight_mode6, "FLTMODE6", FLIGHT_MODE_6), // @Param: LIM_ROLL_CD // @DisplayName: Maximum Bank Angle // @Description: The maximum commanded bank angle in either direction // @Units: centi-Degrees // @Range: 0 9000 // @Increment: 1 // @User: Standard GSCALAR(roll_limit_cd, "LIM_ROLL_CD", HEAD_MAX_CENTIDEGREE), // @Param: LIM_PITCH_MAX // @DisplayName: Maximum Pitch Angle // @Description: The maximum commanded pitch up angle // @Units: centi-Degrees // @Range: 0 9000 // @Increment: 1 // @User: Standard GSCALAR(pitch_limit_max_cd, "LIM_PITCH_MAX", PITCH_MAX_CENTIDEGREE), // @Param: LIM_PITCH_MIN // @DisplayName: Minimum Pitch Angle // @Description: The minimum commanded pitch down angle // @Units: centi-Degrees // @Range: -9000 0 // @Increment: 1 // @User: Standard GSCALAR(pitch_limit_min_cd, "LIM_PITCH_MIN", PITCH_MIN_CENTIDEGREE), // @Param: AUTO_TRIM // @DisplayName: Auto trim // @Description: Set RC trim PWM levels to current levels when switching away from manual mode // @Values: 0:Disabled,1:Enabled // @User: Standard GSCALAR(auto_trim, "TRIM_AUTO", AUTO_TRIM), // @Param: MIX_MODE // @DisplayName: Elevon mixing // @Description: Enable elevon mixing // @Values: 0:Disabled,1:Enabled // @User: User GSCALAR(mix_mode, "ELEVON_MIXING", ELEVON_MIXING), // @Param: ELEVON_REVERSE // @DisplayName: Elevon reverse // @Description: Reverse elevon mixing // @Values: 0:Disabled,1:Enabled // @User: User GSCALAR(reverse_elevons, "ELEVON_REVERSE", ELEVON_REVERSE), // @Param: ELEVON_CH1_REV // @DisplayName: Elevon reverse // @Description: Reverse elevon channel 1 // @Values: -1:Disabled,1:Enabled // @User: User GSCALAR(reverse_ch1_elevon, "ELEVON_CH1_REV", ELEVON_CH1_REVERSE), // @Param: ELEVON_CH2_REV // @DisplayName: Elevon reverse // @Description: Reverse elevon channel 2 // @Values: -1:Disabled,1:Enabled // @User: User GSCALAR(reverse_ch2_elevon, "ELEVON_CH2_REV", ELEVON_CH2_REVERSE), // @Param: SYS_NUM_RESETS // @DisplayName: Num Resets // @Description: Number of APM board resets // @User: Advanced GSCALAR(num_resets, "SYS_NUM_RESETS", 0), // @Param: LOG_BITMASK // @DisplayName: Log bitmask // @Description: bitmap of log fields to enable // @User: Advanced GSCALAR(log_bitmask, "LOG_BITMASK", DEFAULT_LOG_BITMASK), // @Param: RST_SWITCH_CH // @DisplayName: Reset Switch Channel // @Description: RC channel to use to reset to last flight mode after geofence takeover. // @User: Advanced GSCALAR(reset_switch_chan, "RST_SWITCH_CH", 0), // @Param: RST_MISSION_CH // @DisplayName: Reset Mission Channel // @Description: RC channel to use to reset the mission to the first waypoint. When this channel goes above 1750 the mission is reset. Set RST_MISSION_CH to 0 to disable. // @User: Advanced GSCALAR(reset_mission_chan, "RST_MISSION_CH", 0), // @Param: TRIM_ARSPD_CM // @DisplayName: Target airspeed // @Description: Airspeed in cm/s to aim for when airspeed is enabled in auto mode // @Units: cm/s // @User: User GSCALAR(airspeed_cruise_cm, "TRIM_ARSPD_CM", AIRSPEED_CRUISE_CM), // @Param: SCALING_SPEED // @DisplayName: speed used for speed scaling calculations // @Description: Airspeed in m/s to use when calculating surface speed scaling. Note that changing this value will affect all PID values // @Units: m/s // @User: Advanced GSCALAR(scaling_speed, "SCALING_SPEED", SCALING_SPEED), // @Param: MIN_GNDSPD_CM // @DisplayName: Minimum ground speed // @Description: Minimum ground speed in cm/s when under airspeed control // @Units: cm/s // @User: Advanced GSCALAR(min_gndspeed_cm, "MIN_GNDSPD_CM", MIN_GNDSPEED_CM), // @Param: TRIM_PITCH_CD // @DisplayName: Pitch angle offset // @Description: offset to add to pitch - used for trimming tail draggers // @Units: centi-Degrees // @User: Advanced GSCALAR(pitch_trim_cd, "TRIM_PITCH_CD", 0), // @Param: ALT_HOLD_RTL // @DisplayName: RTL altitude // @Description: Return to launch target altitude // @Units: centimeters // @User: User GSCALAR(RTL_altitude_cm, "ALT_HOLD_RTL", ALT_HOLD_HOME_CM), GSCALAR(FBWB_min_altitude_cm, "ALT_HOLD_FBWCM", ALT_HOLD_FBW_CM), // @Param: MAG_ENABLE // @DisplayName: Enable Compass // @Description: Setting this to Enabled(1) will enable the compass. Setting this to Disabled(0) will disable the compass // @Values: 0:Disabled,1:Enabled // @User: Standard GSCALAR(compass_enabled, "MAG_ENABLE", MAGNETOMETER), GSCALAR(flap_1_percent, "FLAP_1_PERCNT", FLAP_1_PERCENT), GSCALAR(flap_1_speed, "FLAP_1_SPEED", FLAP_1_SPEED), GSCALAR(flap_2_percent, "FLAP_2_PERCNT", FLAP_2_PERCENT), GSCALAR(flap_2_speed, "FLAP_2_SPEED", FLAP_2_SPEED), GSCALAR(battery_monitoring, "BATT_MONITOR", 0), GSCALAR(volt_div_ratio, "VOLT_DIVIDER", VOLT_DIV_RATIO), // @Param: APM_PER_VOLT // @DisplayName: Apms per volt // @Description: Number of amps that a 1V reading on the current sensor corresponds to // @Units: A/V // @User: Standard GSCALAR(curr_amp_per_volt, "AMP_PER_VOLT", CURR_AMP_PER_VOLT), // @Param: AMP_OFFSET // @DisplayName: AMP offset // @Description: Voltage offset at zero current on current sensor // @Units: Volts // @User: Standard GSCALAR(curr_amp_offset, "AMP_OFFSET", 0), GSCALAR(input_voltage, "INPUT_VOLTS", INPUT_VOLTAGE), // @Param: BATT_CAPACITY // @DisplayName: Battery capacity // @Description: Capacity of the battery in mAh when full // @Units: mAh // @User: Standard GSCALAR(pack_capacity, "BATT_CAPACITY", 1760), // @Param: BATT_VOLT_PIN // @DisplayName: Battery Voltage sensing pin // @Description: Setting this to 0 ~ 13 will enable battery current sensing on pins A0 ~ A13. // @Values: -1:Disabled, 0:A0, 1:A1, 13:A13 // @User: Standard GSCALAR(battery_volt_pin, "BATT_VOLT_PIN", BATTERY_VOLT_PIN), // @Param: BATT_CURR_PIN // @DisplayName: Battery Current sensing pin // @Description: Setting this to 0 ~ 13 will enable battery current sensing on pins A0 ~ A13. // @Values: -1:Disabled, 1:A1, 2:A2, 12:A12 // @User: Standard GSCALAR(battery_curr_pin, "BATT_CURR_PIN", BATTERY_CURR_PIN), // @Param: RSSI_PIN // @DisplayName: Receiver RSSI sensing pin // @Description: This selects an analog pin for the receiver RSSI voltage. It assumes the voltage is 5V for max rssi, 0V for minimum // @Values: -1:Disabled, 0:A0, 1:A1, 13:A13 // @User: Standard GSCALAR(rssi_pin, "RSSI_PIN", -1), GSCALAR(inverted_flight_ch, "INVERTEDFLT_CH", 0), // barometer ground calibration. The GND_ prefix is chosen for // compatibility with previous releases of ArduPlane GOBJECT(barometer, "GND_", AP_Baro), #if CAMERA == ENABLED // @Group: CAM_ // @Path: ../libraries/AP_Camera/AP_Camera.cpp GOBJECT(camera, "CAM_", AP_Camera), #endif // RC channel //----------- // @Group: RC1_ // @Path: ../libraries/RC_Channel/RC_Channel.cpp GGROUP(channel_roll, "RC1_", RC_Channel), // @Group: RC2_ // @Path: ../libraries/RC_Channel/RC_Channel.cpp GGROUP(channel_pitch, "RC2_", RC_Channel), // @Group: RC3_ // @Path: ../libraries/RC_Channel/RC_Channel.cpp GGROUP(channel_throttle, "RC3_", RC_Channel), // @Group: RC4_ // @Path: ../libraries/RC_Channel/RC_Channel.cpp GGROUP(channel_rudder, "RC4_", RC_Channel), // @Group: RC5_ // @Path: ../libraries/RC_Channel/RC_Channel_aux.cpp, ../libraries/RC_Channel/RC_Channel.cpp GGROUP(rc_5, "RC5_", RC_Channel_aux), // @Group: RC6_ // @Path: ../libraries/RC_Channel/RC_Channel_aux.cpp, ../libraries/RC_Channel/RC_Channel.cpp GGROUP(rc_6, "RC6_", RC_Channel_aux), // @Group: RC7_ // @Path: ../libraries/RC_Channel/RC_Channel_aux.cpp, ../libraries/RC_Channel/RC_Channel.cpp GGROUP(rc_7, "RC7_", RC_Channel_aux), // @Group: RC8_ // @Path: ../libraries/RC_Channel/RC_Channel_aux.cpp, ../libraries/RC_Channel/RC_Channel.cpp GGROUP(rc_8, "RC8_", RC_Channel_aux), #if CONFIG_HAL_BOARD == HAL_BOARD_APM2 // @Group: RC9_ // @Path: ../libraries/RC_Channel/RC_Channel_aux.cpp, ../libraries/RC_Channel/RC_Channel.cpp GGROUP(rc_9, "RC9_", RC_Channel_aux), // @Group: RC10_ // @Path: ../libraries/RC_Channel/RC_Channel_aux.cpp, ../libraries/RC_Channel/RC_Channel.cpp GGROUP(rc_10, "RC10_", RC_Channel_aux), // @Group: RC11_ // @Path: ../libraries/RC_Channel/RC_Channel_aux.cpp, ../libraries/RC_Channel/RC_Channel.cpp GGROUP(rc_11, "RC11_", RC_Channel_aux), #endif GGROUP(pidNavRoll, "HDNG2RLL_", PID), GGROUP(pidNavPitchAirspeed, "ARSP2PTCH_", PID), GGROUP(pidTeThrottle, "ENRGY2THR_", PID), GGROUP(pidNavPitchAltitude, "ALT2PTCH_", PID), GGROUP(pidWheelSteer, "WHEELSTEER_",PID), #if APM_CONTROL == DISABLED GGROUP(pidServoRoll, "RLL2SRV_", PID), GGROUP(pidServoPitch, "PTCH2SRV_", PID), GGROUP(pidServoRudder, "YW2SRV_", PID), #else GGROUP(rollController, "RLL_", AP_RollController), GGROUP(pitchController, "PTCH_", AP_PitchController), GGROUP(yawController, "YWCTL_", AP_YawController), #endif // variables not in the g class which contain EEPROM saved variables // @Group: COMPASS_ // @Path: ../libraries/AP_Compass/Compass.cpp GOBJECT(compass, "COMPASS_", Compass), GOBJECT(gcs0, "SR0_", GCS_MAVLINK), GOBJECT(gcs3, "SR3_", GCS_MAVLINK), // @Group: INS_ // @Path: ../libraries/AP_InertialSensor/AP_InertialSensor.cpp GOBJECT(ins, "INS_", AP_InertialSensor), // @Group: AHRS_ // @Path: ../libraries/AP_AHRS/AP_AHRS.cpp GOBJECT(ahrs, "AHRS_", AP_AHRS), // @Group: ARSPD_ // @Path: ../libraries/AP_Airspeed/AP_Airspeed.cpp GOBJECT(airspeed, "ARSPD_", AP_Airspeed), #if MOUNT == ENABLED // @Group: MNT_ // @Path: ../libraries/AP_Mount/AP_Mount.cpp GOBJECT(camera_mount, "MNT_", AP_Mount), #endif #if MOUNT2 == ENABLED // @Group: MNT2_ // @Path: ../libraries/AP_Mount/AP_Mount.cpp GOBJECT(camera_mount2, "MNT2_", AP_Mount), #endif #if CONFIG_HAL_BOARD == HAL_BOARD_AVR_SITL // @Group: SIM_ // @Path: ../libraries/SITL/SITL.cpp GOBJECT(sitl, "SIM_", SITL), #endif #if OBC_FAILSAFE == ENABLED GOBJECT(obc, "FS_", APM_OBC), #endif AP_VAREND }; static void load_parameters(void) { if (!g.format_version.load() || g.format_version != Parameters::k_format_version) { // erase all parameters cliSerial->printf_P(PSTR("Firmware change: erasing EEPROM...\n")); AP_Param::erase_all(); // save the current format version g.format_version.set_and_save(Parameters::k_format_version); cliSerial->println_P(PSTR("done.")); } else { uint32_t before = micros(); // Load all auto-loaded EEPROM variables AP_Param::load_all(); cliSerial->printf_P(PSTR("load_all took %luus\n"), micros() - before); } }