#pragma once #include #include "AP_HAL_F4Light_Namespace.h" #include "handler.h" #include #include #ifndef HIGH #define HIGH 0x1 #endif #ifndef LOW #define LOW 0x0 #endif #ifndef HAL_GPIO_LED_ON # define HAL_GPIO_LED_ON LOW # define HAL_GPIO_LED_OFF HIGH #endif typedef enum HALPinMode { INPUT = GPIO_INPUT_FLOATING, /**< Basic digital input. The pin voltage is sampled; when it is closer to 3.3v (Vcc) the pin status is high, and when it is closer to 0v (ground) it is low. If no external circuit is pulling the pin voltage to high or low, it will tend to randomly oscillate and be very sensitive to noise (e.g., a breath of air across the pin might cause the state to flip). */ OUTPUT = GPIO_OUTPUT_PP, /* Basic digital output: when the pin is HIGH, the voltage is held at +3.3v (Vcc) and when it is LOW, it is pulled down to ground. */ OUTPUT_ALT = GPIO_AF_OUTPUT_PP, /* basic alternate function mode */ // more complex modes // INPUT_FLOATING = GPIO_INPUT_FLOATING, /**< Synonym for INPUT. */ INPUT_ANALOG = GPIO_INPUT_ANALOG, /**< This is a special mode for when the pin will be used for analog (not digital) reads. Enables ADC conversion to be performed on the voltage at the pin. */ INPUT_PULLDOWN = GPIO_INPUT_PD, /**< The state of the pin in this mode is reported the same way as with INPUT, but the pin voltage is gently "pulled down" towards 0v. This means the state will be low unless an external device is specifically pulling the pin up to 3.3v, in which case the "gentle" pull down will not affect the state of the input. */ INPUT_PULLUP = GPIO_INPUT_PU, /**< The state of the pin in this mode is reported the same way as with INPUT, but the pin voltage is gently "pulled up" towards +3.3v. This means the state will be high unless an external device is specifically pulling the pin down to ground, in which case the "gentle" pull up will not affect the state of the input. */ OUTPUT_OPEN_DRAIN = GPIO_OUTPUT_OD, /**< In open drain mode, the pin indicates "low" by accepting current flow to ground and "high" by providing increased impedance. An example use would be to connect a pin to a bus line (which is pulled up to a positive voltage by a separate supply through a large resistor). When the pin is high, not much current flows through to ground and the line stays at positive voltage; when the pin is low, the bus "drains" to ground with a small amount of current constantly flowing through the large resistor from the external supply. In this mode, no current is ever actually sourced from the pin. */ OUTPUT_OPEN_DRAIN_PU = GPIO_OUTPUT_OD_PU, /**< open drain mode with pull-up */ PWM = GPIO_PIN_MODE_LAST, /**< This is a special mode for when the pin will be used for PWM output (a special case of digital output). */ PWM_OPEN_DRAIN, /**< Like PWM, except that instead of alternating cycles of LOW and HIGH, the voltage on the pin consists of alternating cycles of LOW and floating (disconnected). */ } HAL_PinMode; // HAL_GPIO_INTERRUPT_ not used anywhere typedef enum ExtIntTriggerMode { RISING = (uint8_t)EXTI_RISING, /**< To trigger an interrupt when the pin transitions LOW to HIGH */ FALLING = (uint8_t)EXTI_FALLING, /**< To trigger an interrupt when the pin transitions HIGH to LOW */ CHANGE = (uint8_t)EXTI_RISING_FALLING/**< To trigger an interrupt when the pin transitions from LOW to HIGH or HIGH to LOW (i.e., when the pin changes). */ } ExtIntTriggerMode; class F4Light::DigitalSource : public AP_HAL::DigitalSource { public: DigitalSource(const gpio_dev *device, uint8_t bit): _device(device), _bit(bit){ } void mode(uint8_t output); uint8_t read() { return _read(); } void write(uint8_t value) { _write(value); } inline uint8_t _read() { return gpio_read_bit(_device, _bit) ? HIGH : LOW; } inline void _write(uint8_t value) { gpio_write_bit(_device, _bit, value); } inline void toggle() { gpio_toggle_bit(_device, _bit); } private: const gpio_dev *_device; uint8_t _bit; }; class F4Light::GPIO : public AP_HAL::GPIO { public: GPIO() {}; void init() override { gpio_init_all(); } void pinMode(uint8_t pin, uint8_t output) override; uint8_t read(uint8_t pin) override; void write(uint8_t pin, uint8_t value) override; void toggle(uint8_t pin) override; /* Alternative interface: */ AP_HAL::DigitalSource* channel(uint16_t n); /* Interrupt interface: */ static bool _attach_interrupt(uint8_t pin, Handler h, uint8_t mode, uint8_t priority); inline bool attach_interrupt(uint8_t pin, AP_HAL::MemberProc p, uint8_t mode) { Revo_handler h = { .mp = p }; return _attach_interrupt(pin, h.h, mode, GPIO_INT_PRIORITY); } inline bool attach_interrupt(uint8_t pin, AP_HAL::Proc p, uint8_t mode) { Revo_handler h = { .hp = p }; return _attach_interrupt(pin, h.h, mode, GPIO_INT_PRIORITY); } void detach_interrupt(uint8_t pin); static inline void enable_interrupt(uint8_t pin, bool e) { exti_enable_interrupt((afio_exti_num)(PIN_MAP[pin].gpio_bit), e); } /* return true if USB cable is connected */ inline bool usb_connected(void) override { return gpio_read_bit(PIN_MAP[BOARD_USB_SENSE].gpio_device,PIN_MAP[BOARD_USB_SENSE].gpio_bit); } inline int8_t analogPinToDigitalPin(uint8_t pin) override { return pin; } static inline uint8_t analogPinToDigital(uint8_t pin){ return pin; } // internal usage static versions static void _pinMode(uint8_t pin, uint8_t output); static inline uint8_t _read(uint8_t pin) { const stm32_pin_info &pp = PIN_MAP[pin]; return gpio_read_bit( pp.gpio_device, pp.gpio_bit) ? HIGH : LOW; } static inline void _write(uint8_t pin, uint8_t value) { const stm32_pin_info &pp = PIN_MAP[pin]; gpio_write_bit(pp.gpio_device, pp.gpio_bit, value); } static inline void _toggle(uint8_t pin) { const stm32_pin_info &p = PIN_MAP[pin]; gpio_toggle_bit(p.gpio_device, p.gpio_bit); } static inline void _setSpeed(uint8_t pin, GPIOSpeed_t gpio_speed) { const stm32_pin_info &pp = PIN_MAP[pin]; gpio_set_speed(pp.gpio_device, pp.gpio_bit, gpio_speed);} static inline DigitalSource* get_channel(uint16_t pin) { const stm32_pin_info &pp = PIN_MAP[pin]; return new DigitalSource(pp.gpio_device, pp.gpio_bit); } }; static inline exti_trigger_mode exti_out_mode(ExtIntTriggerMode mode) { return (exti_trigger_mode)mode; } extern "C" { void digitalWrite(uint8_t pin, uint8_t value); uint8_t digitalRead(uint8_t pin); void digitalToggle(uint8_t pin); }