#include <AP_HAL/AP_HAL.h>
#include "AC_PosControl.h"
#include <AP_Math/AP_Math.h>
#include <AP_Logger/AP_Logger.h>

extern const AP_HAL::HAL& hal;

#if APM_BUILD_TYPE(APM_BUILD_ArduPlane)
 // default gains for Plane
 # define POSCONTROL_POS_Z_P                    1.0f    // vertical position controller P gain default
 # define POSCONTROL_VEL_Z_P                    5.0f    // vertical velocity controller P gain default
 # define POSCONTROL_VEL_Z_IMAX                 1000.0f // vertical velocity controller IMAX gain default
 # define POSCONTROL_VEL_Z_FILT_HZ              5.0f    // vertical velocity controller input filter
 # define POSCONTROL_VEL_Z_FILT_D_HZ            5.0f    // vertical velocity controller input filter for D
 # define POSCONTROL_ACC_Z_P                    0.3f    // vertical acceleration controller P gain default
 # define POSCONTROL_ACC_Z_I                    1.0f    // vertical acceleration controller I gain default
 # define POSCONTROL_ACC_Z_D                    0.0f    // vertical acceleration controller D gain default
 # define POSCONTROL_ACC_Z_IMAX                 800     // vertical acceleration controller IMAX gain default
 # define POSCONTROL_ACC_Z_FILT_HZ              10.0f   // vertical acceleration controller input filter default
 # define POSCONTROL_ACC_Z_DT                   0.02f   // vertical acceleration controller dt default
 # define POSCONTROL_POS_XY_P                   1.0f    // horizontal position controller P gain default
 # define POSCONTROL_VEL_XY_P                   1.4f    // horizontal velocity controller P gain default
 # define POSCONTROL_VEL_XY_I                   0.7f    // horizontal velocity controller I gain default
 # define POSCONTROL_VEL_XY_D                   0.35f   // horizontal velocity controller D gain default
 # define POSCONTROL_VEL_XY_IMAX                1000.0f // horizontal velocity controller IMAX gain default
 # define POSCONTROL_VEL_XY_FILT_HZ             5.0f    // horizontal velocity controller input filter
 # define POSCONTROL_VEL_XY_FILT_D_HZ           5.0f    // horizontal velocity controller input filter for D
#elif APM_BUILD_TYPE(APM_BUILD_ArduSub)
 // default gains for Sub
 # define POSCONTROL_POS_Z_P                    3.0f    // vertical position controller P gain default
 # define POSCONTROL_VEL_Z_P                    8.0f    // vertical velocity controller P gain default
 # define POSCONTROL_VEL_Z_IMAX                 1000.0f // vertical velocity controller IMAX gain default
 # define POSCONTROL_VEL_Z_FILT_HZ              5.0f    // vertical velocity controller input filter
 # define POSCONTROL_VEL_Z_FILT_D_HZ            5.0f    // vertical velocity controller input filter for D
 # define POSCONTROL_ACC_Z_P                    0.5f    // vertical acceleration controller P gain default
 # define POSCONTROL_ACC_Z_I                    0.1f    // vertical acceleration controller I gain default
 # define POSCONTROL_ACC_Z_D                    0.0f    // vertical acceleration controller D gain default
 # define POSCONTROL_ACC_Z_IMAX                 100     // vertical acceleration controller IMAX gain default
 # define POSCONTROL_ACC_Z_FILT_HZ              20.0f   // vertical acceleration controller input filter default
 # define POSCONTROL_ACC_Z_DT                   0.0025f // vertical acceleration controller dt default
 # define POSCONTROL_POS_XY_P                   1.0f    // horizontal position controller P gain default
 # define POSCONTROL_VEL_XY_P                   1.0f    // horizontal velocity controller P gain default
 # define POSCONTROL_VEL_XY_I                   0.5f    // horizontal velocity controller I gain default
 # define POSCONTROL_VEL_XY_D                   0.0f    // horizontal velocity controller D gain default
 # define POSCONTROL_VEL_XY_IMAX                1000.0f // horizontal velocity controller IMAX gain default
 # define POSCONTROL_VEL_XY_FILT_HZ             5.0f    // horizontal velocity controller input filter
 # define POSCONTROL_VEL_XY_FILT_D_HZ           5.0f    // horizontal velocity controller input filter for D
#else
 // default gains for Copter / TradHeli
 # define POSCONTROL_POS_Z_P                    1.0f    // vertical position controller P gain default
 # define POSCONTROL_VEL_Z_P                    5.0f    // vertical velocity controller P gain default
 # define POSCONTROL_VEL_Z_IMAX                 1000.0f // vertical velocity controller IMAX gain default
 # define POSCONTROL_VEL_Z_FILT_HZ              5.0f    // vertical velocity controller input filter
 # define POSCONTROL_VEL_Z_FILT_D_HZ            5.0f    // vertical velocity controller input filter for D
 # define POSCONTROL_ACC_Z_P                    0.5f    // vertical acceleration controller P gain default
 # define POSCONTROL_ACC_Z_I                    1.0f    // vertical acceleration controller I gain default
 # define POSCONTROL_ACC_Z_D                    0.0f    // vertical acceleration controller D gain default
 # define POSCONTROL_ACC_Z_IMAX                 800     // vertical acceleration controller IMAX gain default
 # define POSCONTROL_ACC_Z_FILT_HZ              20.0f   // vertical acceleration controller input filter default
 # define POSCONTROL_ACC_Z_DT                   0.0025f // vertical acceleration controller dt default
 # define POSCONTROL_POS_XY_P                   1.0f    // horizontal position controller P gain default
 # define POSCONTROL_VEL_XY_P                   2.0f    // horizontal velocity controller P gain default
 # define POSCONTROL_VEL_XY_I                   1.0f    // horizontal velocity controller I gain default
 # define POSCONTROL_VEL_XY_D                   0.5f    // horizontal velocity controller D gain default
 # define POSCONTROL_VEL_XY_IMAX                1000.0f // horizontal velocity controller IMAX gain default
 # define POSCONTROL_VEL_XY_FILT_HZ             5.0f    // horizontal velocity controller input filter
 # define POSCONTROL_VEL_XY_FILT_D_HZ           5.0f    // horizontal velocity controller input filter for D
#endif

// vibration compensation gains
#define POSCONTROL_VIBE_COMP_P_GAIN 0.250f
#define POSCONTROL_VIBE_COMP_I_GAIN 0.125f

const AP_Param::GroupInfo AC_PosControl::var_info[] = {
    // 0 was used for HOVER

    // @Param: _ACC_XY_FILT
    // @DisplayName: XY Acceleration filter cutoff frequency
    // @Description: Lower values will slow the response of the navigation controller and reduce twitchiness
    // @Units: Hz
    // @Range: 0.5 5
    // @Increment: 0.1
    // @User: Advanced

    // @Param: _POSZ_P
    // @DisplayName: Position (vertical) controller P gain
    // @Description: Position (vertical) controller P gain.  Converts the difference between the desired altitude and actual altitude into a climb or descent rate which is passed to the throttle rate controller
    // @Range: 1.000 3.000
    // @User: Standard
    AP_SUBGROUPINFO(_p_pos_z, "_POSZ_", 2, AC_PosControl, AC_P_1D),

    // @Param: _VELZ_P
    // @DisplayName: Velocity (vertical) controller P gain
    // @Description: Velocity (vertical) controller P gain.  Converts the difference between desired vertical speed and actual speed into a desired acceleration that is passed to the throttle acceleration controller
    // @Range: 1.000 8.000
    // @User: Standard

    // @Param: _VELZ_I
    // @DisplayName: Velocity (vertical) controller I gain
    // @Description: Velocity (vertical) controller I gain.  Corrects long-term difference in desired velocity to a target acceleration
    // @Range: 0.02 1.00
    // @Increment: 0.01
    // @User: Advanced

    // @Param: _VELZ_IMAX
    // @DisplayName: Velocity (vertical) controller I gain maximum
    // @Description: Velocity (vertical) controller I gain maximum.  Constrains the target acceleration that the I gain will output
    // @Range: 1.000 8.000
    // @User: Standard

    // @Param: _VELZ_D
    // @DisplayName: Velocity (vertical) controller D gain
    // @Description: Velocity (vertical) controller D gain.  Corrects short-term changes in velocity
    // @Range: 0.00 1.00
    // @Increment: 0.001
    // @User: Advanced

    // @Param: _VELZ_FF
    // @DisplayName: Velocity (vertical) controller Feed Forward gain
    // @Description: Velocity (vertical) controller Feed Forward gain.  Produces an output that is proportional to the magnitude of the target
    // @Range: 0 1
    // @Increment: 0.01
    // @User: Advanced

    // @Param: _VELZ_FLTE
    // @DisplayName: Velocity (vertical) error filter
    // @Description: Velocity (vertical) error filter.  This filter (in Hz) is applied to the input for P and I terms
    // @Range: 0 100
    // @Units: Hz
    // @User: Advanced

    // @Param: _VELZ_FLTD
    // @DisplayName: Velocity (vertical) input filter for D term
    // @Description: Velocity (vertical) input filter for D term.  This filter (in Hz) is applied to the input for D terms
    // @Range: 0 100
    // @Units: Hz
    // @User: Advanced
    AP_SUBGROUPINFO(_pid_vel_z, "_VELZ_", 3, AC_PosControl, AC_PID_Basic),

    // @Param: _ACCZ_P
    // @DisplayName: Acceleration (vertical) controller P gain
    // @Description: Acceleration (vertical) controller P gain.  Converts the difference between desired vertical acceleration and actual acceleration into a motor output
    // @Range: 0.200 1.500
    // @Increment: 0.05
    // @User: Standard

    // @Param: _ACCZ_I
    // @DisplayName: Acceleration (vertical) controller I gain
    // @Description: Acceleration (vertical) controller I gain.  Corrects long-term difference in desired vertical acceleration and actual acceleration
    // @Range: 0.000 3.000
    // @User: Standard

    // @Param: _ACCZ_IMAX
    // @DisplayName: Acceleration (vertical) controller I gain maximum
    // @Description: Acceleration (vertical) controller I gain maximum.  Constrains the maximum pwm that the I term will generate
    // @Range: 0 1000
    // @Units: d%
    // @User: Standard

    // @Param: _ACCZ_D
    // @DisplayName: Acceleration (vertical) controller D gain
    // @Description: Acceleration (vertical) controller D gain.  Compensates for short-term change in desired vertical acceleration vs actual acceleration
    // @Range: 0.000 0.400
    // @User: Standard

    // @Param: _ACCZ_FF
    // @DisplayName: Acceleration (vertical) controller feed forward
    // @Description: Acceleration (vertical) controller feed forward
    // @Range: 0 0.5
    // @Increment: 0.001
    // @User: Standard

    // @Param: _ACCZ_FLTT
    // @DisplayName: Acceleration (vertical) controller target frequency in Hz
    // @Description: Acceleration (vertical) controller target frequency in Hz
    // @Range: 1 50
    // @Increment: 1
    // @Units: Hz
    // @User: Standard

    // @Param: _ACCZ_FLTE
    // @DisplayName: Acceleration (vertical) controller error frequency in Hz
    // @Description: Acceleration (vertical) controller error frequency in Hz
    // @Range: 1 100
    // @Increment: 1
    // @Units: Hz
    // @User: Standard

    // @Param: _ACCZ_FLTD
    // @DisplayName: Acceleration (vertical) controller derivative frequency in Hz
    // @Description: Acceleration (vertical) controller derivative frequency in Hz
    // @Range: 1 100
    // @Increment: 1
    // @Units: Hz
    // @User: Standard

    // @Param: _ACCZ_SMAX
    // @DisplayName: Accel (vertical) slew rate limit
    // @Description: Sets an upper limit on the slew rate produced by the combined P and D gains. If the amplitude of the control action produced by the rate feedback exceeds this value, then the D+P gain is reduced to respect the limit. This limits the amplitude of high frequency oscillations caused by an excessive gain. The limit should be set to no more than 25% of the actuators maximum slew rate to allow for load effects. Note: The gain will not be reduced to less than 10% of the nominal value. A value of zero will disable this feature.
    // @Range: 0 200
    // @Increment: 0.5
    // @User: Advanced

    AP_SUBGROUPINFO(_pid_accel_z, "_ACCZ_", 4, AC_PosControl, AC_PID),

    // @Param: _POSXY_P
    // @DisplayName: Position (horizontal) controller P gain
    // @Description: Position controller P gain.  Converts the distance (in the latitude direction) to the target location into a desired speed which is then passed to the loiter latitude rate controller
    // @Range: 0.500 2.000
    // @User: Standard
    AP_SUBGROUPINFO(_p_pos_xy, "_POSXY_", 5, AC_PosControl, AC_P_2D),

    // @Param: _VELXY_P
    // @DisplayName: Velocity (horizontal) P gain
    // @Description: Velocity (horizontal) P gain.  Converts the difference between desired and actual velocity to a target acceleration
    // @Range: 0.1 6.0
    // @Increment: 0.1
    // @User: Advanced

    // @Param: _VELXY_I
    // @DisplayName: Velocity (horizontal) I gain
    // @Description: Velocity (horizontal) I gain.  Corrects long-term difference between desired and actual velocity to a target acceleration
    // @Range: 0.02 1.00
    // @Increment: 0.01
    // @User: Advanced

    // @Param: _VELXY_D
    // @DisplayName: Velocity (horizontal) D gain
    // @Description: Velocity (horizontal) D gain.  Corrects short-term changes in velocity
    // @Range: 0.00 1.00
    // @Increment: 0.001
    // @User: Advanced

    // @Param: _VELXY_IMAX
    // @DisplayName: Velocity (horizontal) integrator maximum
    // @Description: Velocity (horizontal) integrator maximum.  Constrains the target acceleration that the I gain will output
    // @Range: 0 4500
    // @Increment: 10
    // @Units: cm/s/s
    // @User: Advanced

    // @Param: _VELXY_FILT
    // @DisplayName: Velocity (horizontal) input filter
    // @Description: Velocity (horizontal) input filter.  This filter (in Hz) is applied to the input for P and I terms
    // @Range: 0 100
    // @Units: Hz
    // @User: Advanced

    // @Param: _VELXY_D_FILT
    // @DisplayName: Velocity (horizontal) input filter
    // @Description: Velocity (horizontal) input filter.  This filter (in Hz) is applied to the input for D term
    // @Range: 0 100
    // @Units: Hz
    // @User: Advanced

    // @Param: _VELXY_FF
    // @DisplayName: Velocity (horizontal) feed forward gain
    // @Description: Velocity (horizontal) feed forward gain.  Converts the difference between desired velocity to a target acceleration
    // @Range: 0 6
    // @Increment: 0.01
    // @User: Advanced
    AP_SUBGROUPINFO(_pid_vel_xy, "_VELXY_", 6, AC_PosControl, AC_PID_2D),

    // @Param: _ANGLE_MAX
    // @DisplayName: Position Control Angle Max
    // @Description: Maximum lean angle autopilot can request.  Set to zero to use ANGLE_MAX parameter value
    // @Units: deg
    // @Range: 0 45
    // @Increment: 1
    // @User: Advanced
    AP_GROUPINFO("_ANGLE_MAX", 7, AC_PosControl, _lean_angle_max, 0.0f),

    // @Param: _TC_XY
    // @DisplayName: Time constant for the horizontal kinimatic input shaping
    // @Description: Time constant of the horizontal kinimatic path generation used to determine how quickly the aircraft varies the acceleration target
    // @Units: s
    // @Range: 0.25 2
    // @Increment: 0.01
    // @User: Advanced
    AP_GROUPINFO("_TC_XY", 8, AC_PosControl, _shaping_tc_xy_s, POSCONTROL_DEFAULT_SHAPER_TC),

    // @Param: _TC_Z
    // @DisplayName: Time constant for the vertical kinimatic input shaping
    // @Description: Time constant of the vertical kinimatic path generation used to determine how quickly the aircraft varies the acceleration target
    // @Units: s
    // @Range: 0.1 1
    // @Increment: 0.01
    // @User: Advanced
    AP_GROUPINFO("_TC_Z", 9, AC_PosControl, _shaping_tc_z_s, POSCONTROL_DEFAULT_SHAPER_TC),

    AP_GROUPEND
};

// Default constructor.
// Note that the Vector/Matrix constructors already implicitly zero
// their values.
//
AC_PosControl::AC_PosControl(AP_AHRS_View& ahrs, const AP_InertialNav& inav,
                             const AP_Motors& motors, AC_AttitudeControl& attitude_control, float dt) :
    _ahrs(ahrs),
    _inav(inav),
    _motors(motors),
    _attitude_control(attitude_control),
    _p_pos_z(POSCONTROL_POS_Z_P, dt),
    _pid_vel_z(POSCONTROL_VEL_Z_P, 0.0f, 0.0f, 0.0f, POSCONTROL_VEL_Z_IMAX, POSCONTROL_VEL_Z_FILT_HZ, POSCONTROL_VEL_Z_FILT_D_HZ, dt),
    _pid_accel_z(POSCONTROL_ACC_Z_P, POSCONTROL_ACC_Z_I, POSCONTROL_ACC_Z_D, 0.0f, POSCONTROL_ACC_Z_IMAX, 0.0f, POSCONTROL_ACC_Z_FILT_HZ, 0.0f, dt),
    _p_pos_xy(POSCONTROL_POS_XY_P, dt),
    _pid_vel_xy(POSCONTROL_VEL_XY_P, POSCONTROL_VEL_XY_I, POSCONTROL_VEL_XY_D, 0.0f, POSCONTROL_VEL_XY_IMAX, POSCONTROL_VEL_XY_FILT_HZ, POSCONTROL_VEL_XY_FILT_D_HZ, dt),
    _dt(dt),
    _vel_max_down_cms(POSCONTROL_SPEED_DOWN),
    _vel_max_up_cms(POSCONTROL_SPEED_UP),
    _vel_max_xy_cms(POSCONTROL_SPEED),
    _accel_max_z_cmss(POSCONTROL_ACCEL_Z),
    _accel_max_xy_cmss(POSCONTROL_ACCEL_XY),
    _tc_xy_s(POSCONTROL_DEFAULT_SHAPER_TC),
    _tc_z_s(POSCONTROL_DEFAULT_SHAPER_TC)
{
    AP_Param::setup_object_defaults(this, var_info);

    // initialise flags
    _limit.pos_xy = true;
    _limit.pos_up = true;
    _limit.pos_down = true;
}


///
/// 3D position shaper
///

/// input_pos_vel_accel_xyz - calculate a jerk limited path from the current position, velocity and acceleration to an input position velocity and acceleration.
///     The function takes the current position, velocity, and acceleration and calculates the required jerk limited adjustment to the acceleration for the next time dt.
///     The kinematic path is constrained by the maximum acceleration and time constant set using the function set_max_speed_accel_xy and time constant.
///     The time constant defines the acceleration error decay in the kinematic path as the system approaches constant acceleration.
///     The time constant also defines the time taken to achieve the maximum acceleration.
///     The function alters the input velocity to be the velocity that the system could reach zero acceleration in the minimum time.
void AC_PosControl::input_pos_vel_accel_xyz(const Vector3f& pos)
{
    // check for ekf xy position reset
    handle_ekf_xy_reset();
    handle_ekf_z_reset();
    Vector3f dest_vector = pos - _pos_target;

    // calculated increased maximum acceleration if over speed
    float accel_z_cmss = _accel_max_z_cmss;
    if (_vel_desired.z < _vel_max_down_cms && !is_zero(_vel_max_down_cms)) {
        accel_z_cmss *= POSCONTROL_OVERSPEED_GAIN_Z * _vel_desired.z / _vel_max_down_cms;
    }
    if (_vel_desired.z > _vel_max_up_cms && !is_zero(_vel_max_up_cms)) {
        accel_z_cmss *= POSCONTROL_OVERSPEED_GAIN_Z * _vel_desired.z / _vel_max_up_cms;
    }

    update_pos_vel_accel_xy(_pos_target, _vel_desired, _accel_desired, _dt, _limit_vector);

    // adjust desired alt if motors have not hit their limits
    update_pos_vel_accel_z(_pos_target, _vel_desired, _accel_desired, _dt, _limit_vector);

    float vel_max_xy_cms = _vel_max_xy_cms;
    float vel_max_z_cms = 0.0f;
    if (is_positive(dest_vector.length_squared()) ) {
        dest_vector.normalize();
        float dest_vector_xy_length = Vector2f{dest_vector.x, dest_vector.y}.length();

        float vel_max_cms = kinematic_limit(dest_vector, _vel_max_xy_cms, _vel_max_up_cms, _vel_max_down_cms);
        vel_max_xy_cms = vel_max_cms * dest_vector_xy_length;
        vel_max_z_cms = vel_max_cms * dest_vector.z;
    }


    Vector3f vel;
    Vector3f accel;
    shape_pos_vel_accel_xy(pos, vel, accel, _pos_target, _vel_desired, _accel_desired,
        vel_max_xy_cms, _vel_max_xy_cms, _accel_max_xy_cmss, _tc_xy_s, _dt);
    shape_pos_vel_accel_z(pos, vel, accel,
        _pos_target, _vel_desired, _accel_desired,
        vel_max_z_cms, _vel_max_down_cms, _vel_max_up_cms,
        -constrain_float(accel_z_cmss, 0.0f, 750.0f), accel_z_cmss,
        _tc_z_s, _dt);
}


///
/// Lateral position controller
///

/// set_max_speed_accel_xy - set the maximum horizontal speed in cm/s and acceleration in cm/s/s and position controller correction acceleration limit
void AC_PosControl::set_max_speed_accel_xy(float speed_cms, float accel_cmss, float accel_limit_cmss)
{
    // return immediately if no change
    if (is_equal(_vel_max_xy_cms, speed_cms) && is_equal(_accel_max_xy_cmss, accel_cmss) && is_equal(_accel_limit_xy_cmss, accel_limit_cmss)) {
        return;
    }
    _vel_max_xy_cms = speed_cms;
    _accel_max_xy_cmss = accel_cmss;
    _accel_limit_xy_cmss = accel_limit_cmss;

    if (is_positive(_accel_limit_xy_cmss)) {
        // Use half the maximum acceleration for the position controller approach limit to ensure velocity controller has sufficient head room to operate effectively.
        accel_cmss = MIN(_accel_max_xy_cmss, 0.5f * _accel_limit_xy_cmss);
    }

    _p_pos_xy.set_limits(_vel_max_xy_cms, accel_cmss, 0.0f);

    // ensure the horizontal time constant is not less than the vehicle is capable of
    const float lean_angle = _accel_max_xy_cmss / (GRAVITY_MSS * 100.0 * M_PI / 18000.0);
    const float angle_accel = MIN(_attitude_control.get_accel_pitch_max(), _attitude_control.get_accel_roll_max());
    if (is_positive(angle_accel)) {
        _tc_xy_s = MAX(_shaping_tc_xy_s, 2.0 * sqrtf(lean_angle / angle_accel));
    } else {
        _tc_xy_s = _shaping_tc_xy_s;
    }
}

/// init_xy_controller - initialise the position controller to the current position, velocity, acceleration and attitude.
///     This function is the default initialisation for any position control that provides position, velocity and acceleration.
void AC_PosControl::init_xy_controller()
{
    init_xy();

    // set resultant acceleration to current attitude target
    Vector3f accel_target;
    lean_angles_to_accel_xy(accel_target.x, accel_target.y);
    _pid_vel_xy.set_integrator(accel_target - _accel_desired);
}

/// init_xy_controller_stopping_point - initialise the position controller to the stopping point with zero velocity and acceleration.
///     This function should be used when the expected kinimatic path assumes a stationary initial condition but does not specify a specific starting position.
///     The starting position can be retrieved by getting the position target using get_pos_target_cm() after calling this function.
void AC_PosControl::init_xy_controller_stopping_point()
{
    init_xy();
    get_stopping_point_xy_cm(_pos_target);
    _vel_desired.x = 0.0f;
    _vel_desired.y = 0.0f;
    _accel_desired.x = 0.0f;
    _accel_desired.y = 0.0f;

    // set resultant acceleration to current attitude target
    Vector3f accel_target;
    lean_angles_to_accel_xy(accel_target.x, accel_target.y);
    _pid_vel_xy.set_integrator(accel_target);
}

// relax_velocity_controller_xy - initialise the position controller to the current position and velocity with decaying acceleration.
///     This function decays the output acceleration by 95% every half second to achieve a smooth transition to zero requested acceleration.
void AC_PosControl::relax_velocity_controller_xy()
{
    init_xy();

    // decay resultant acceleration and therefore current attitude target to zero
    float decay = 1.0 - _dt / (_dt + POSCONTROL_RELAX_TC);
    _accel_target.x *= decay;
    _accel_target.y *= decay;
    _accel_desired.x = _accel_target.x;
    _accel_desired.y = _accel_target.y;
}

/// init_xy - initialise the position controller to the current position, velocity and acceleration.
///     This function is private and contains all the shared xy axis initialisation functions
void AC_PosControl::init_xy()
{
    // set roll, pitch lean angle targets to current attitude
    const Vector3f &att_target_euler_cd = _attitude_control.get_att_target_euler_cd();
    _roll_target = att_target_euler_cd.x;
    _pitch_target = att_target_euler_cd.y;
    _yaw_target = att_target_euler_cd.z; // todo: this should be thrust vector heading, not yaw.
    _yaw_rate_target = 0.0f;

    const Vector3f curr_pos = _inav.get_position();
    _pos_target.x = curr_pos.x;
    _pos_target.y = curr_pos.y;

    const Vector3f &curr_vel = _inav.get_velocity();
    _vel_desired.x = curr_vel.x;
    _vel_desired.y = curr_vel.y;
    _vel_target.x = curr_vel.x;
    _vel_target.y = curr_vel.y;

    // initialise I terms from lean angles
    _pid_vel_xy.reset_filter();
    _pid_vel_xy.reset_I();

    const Vector3f &curr_accel = _ahrs.get_accel_ef_blended() * 100.0f;
    _accel_desired.x = curr_accel.x;
    _accel_desired.y = curr_accel.y;
    _accel_target.x = curr_accel.x;
    _accel_target.y = curr_accel.y;

    // initialise ekf xy reset handler
    init_ekf_xy_reset();

    // initialise z_controller time out
    _last_update_xy_us = AP_HAL::micros64();
}

/// input_vel_accel_xy - calculate a jerk limited path from the current position, velocity and acceleration to an input velocity and acceleration.
///     The vel is projected forwards in time based on a time step of dt and acceleration accel.
///     The function takes the current position, velocity, and acceleration and calculates the required jerk limited adjustment to the acceleration for the next time dt.
///     The kinematic path is constrained by the maximum acceleration and time constant set using the function set_max_speed_accel_xy and time constant.
///     The time constant defines the acceleration error decay in the kinematic path as the system approaches constant acceleration.
///     The time constant also defines the time taken to achieve the maximum acceleration.
void AC_PosControl::input_vel_accel_xy(Vector3f& vel, const Vector3f& accel)
{
    // check for ekf xy position reset
    handle_ekf_xy_reset();

    update_pos_vel_accel_xy(_pos_target, _vel_desired, _accel_desired, _dt, _limit_vector);

    shape_vel_accel_xy(vel, accel, _vel_desired, _accel_desired,
        _vel_max_xy_cms, _accel_max_xy_cmss, _tc_xy_s, _dt);

    update_vel_accel_xy(vel, accel, _dt, Vector3f());
}

/// input_pos_vel_accel_xy - calculate a jerk limited path from the current position, velocity and acceleration to an input position velocity and acceleration.
///     The pos and vel are projected forwards in time based on a time step of dt and acceleration accel.
///     The function takes the current position, velocity, and acceleration and calculates the required jerk limited adjustment to the acceleration for the next time dt.
///     The kinematic path is constrained by the maximum acceleration and time constant set using the function set_max_speed_accel_xy and time constant.
///     The time constant defines the acceleration error decay in the kinematic path as the system approaches constant acceleration.
///     The time constant also defines the time taken to achieve the maximum acceleration.
void AC_PosControl::input_pos_vel_accel_xy(Vector3f& pos, Vector3f& vel, const Vector3f& accel)
{
    // check for ekf xy position reset
    handle_ekf_xy_reset();

    update_pos_vel_accel_xy(_pos_target, _vel_desired, _accel_desired, _dt, _limit_vector);

    shape_pos_vel_accel_xy(pos, vel, accel, _pos_target, _vel_desired, _accel_desired,
        _vel_max_xy_cms, _vel_max_xy_cms, _accel_max_xy_cmss, _tc_xy_s, _dt);

    update_pos_vel_accel_xy(pos, vel, accel, _dt, Vector3f());
}

/// stop_pos_xy_stabilisation - sets the target to the current position to remove any position corrections from the system
void AC_PosControl::stop_pos_xy_stabilisation()
{
    const Vector3f& curr_pos = _inav.get_position();
    _pos_target.x = curr_pos.x;
    _pos_target.y = curr_pos.y;
}

/// stop_vel_xy_stabilisation - sets the target to the current position and velocity to the current velocity to remove any position and velocity corrections from the system
void AC_PosControl::stop_vel_xy_stabilisation()
{
    const Vector3f curr_pos = _inav.get_position();
    _pos_target.x = curr_pos.x;
    _pos_target.y = curr_pos.y;

    const Vector3f &curr_vel = _inav.get_velocity();
    _vel_desired.x = curr_vel.x;
    _vel_desired.y = curr_vel.y;
    _vel_target.x = curr_vel.x;
    _vel_target.y = curr_vel.y;

    // initialise I terms from lean angles
    _pid_vel_xy.reset_filter();
    _pid_vel_xy.reset_I();
}

// is_active_xy - returns true if the xy position controller has been run in the previous 5 loop times
bool AC_PosControl::is_active_xy() const
{
    return ((AP_HAL::micros64() - _last_update_xy_us) <= _dt * 5000000.0);
}

/// update_xy_controller - runs the horizontal position controller correcting position, velocity and acceleration errors.
///     Position and velocity errors are converted to velocity and acceleration targets using PID objects
///     Desired velocity and accelerations are added to these corrections as they are calculated
///     Kinematically consistent target position and desired velocity and accelerations should be provided before calling this function
void AC_PosControl::update_xy_controller()
{
    // Check for position control time out
    if ( !is_active_xy() ) {
        init_xy_controller();
        if (has_good_timing()) {
            // call internal error because initialisation has not been done
            INTERNAL_ERROR(AP_InternalError::error_t::flow_of_control);
        }
    }
    _last_update_xy_us = AP_HAL::micros64();

    float ekfGndSpdLimit, ekfNavVelGainScaler;
    AP::ahrs_navekf().getEkfControlLimits(ekfGndSpdLimit, ekfNavVelGainScaler);

    // Position Controller

    const Vector3f &curr_pos = _inav.get_position();
    Vector2f vel_target = _p_pos_xy.update_all(_pos_target.x, _pos_target.y, curr_pos, _limit.pos_xy);

    // add velocity feed-forward scaled to compensate for optical flow measurement induced EKF noise
    vel_target *= ekfNavVelGainScaler;
    _vel_target.x = vel_target.x;
    _vel_target.y = vel_target.y;
    _vel_target.x += _vel_desired.x;
    _vel_target.y += _vel_desired.y;

    // Velocity Controller

    // check if vehicle velocity is being overridden
    // todo: remove this and use input shaping
    if (_flags.vehicle_horiz_vel_override) {
        _flags.vehicle_horiz_vel_override = false;
    } else {
        _vehicle_horiz_vel.x = _inav.get_velocity().x;
        _vehicle_horiz_vel.y = _inav.get_velocity().y;
    }
    Vector2f accel_target = _pid_vel_xy.update_all(Vector2f{_vel_target.x, _vel_target.y}, _vehicle_horiz_vel, Vector2f(_limit_vector.x, _limit_vector.y));
    // acceleration to correct for velocity error and scale PID output to compensate for optical flow measurement induced EKF noise
    accel_target *= ekfNavVelGainScaler;

    _limit_vector.x = 0.0f;
    _limit_vector.y = 0.0f;
    if (!is_zero(_accel_limit_xy_cmss)) {
        if (accel_target.limit_length(_accel_limit_xy_cmss)) {
            _limit_vector.x = accel_target.x;
            _limit_vector.y = accel_target.y;
        }
    }

    // pass the correction acceleration to the target acceleration output
    _accel_target.x = accel_target.x;
    _accel_target.y = accel_target.y;

    // Add feed forward into the target acceleration output
    _accel_target.x += _accel_desired.x;
    _accel_target.y += _accel_desired.y;

    // Acceleration Controller

    // limit acceleration using maximum lean angles
    float angle_max = MIN(_attitude_control.get_althold_lean_angle_max(), get_lean_angle_max_cd());
    float accel_max = GRAVITY_MSS * 100.0f * tanf(ToRad(angle_max * 0.01f));
    if (_accel_target.limit_length_xy(accel_max)) {
        _limit_vector.x = _accel_target.x;
        _limit_vector.y = _accel_target.y;
    }

    // update angle targets that will be passed to stabilize controller
    accel_to_lean_angles(_accel_target.x, _accel_target.y, _roll_target, _pitch_target);
    calculate_yaw_and_rate_yaw();
}


///
/// Vertical position controller
///

/// set_max_speed_accel_z - set the maximum vertical speed in cm/s and acceleration in cm/s/s and position controller correction acceleration limit
///     speed_down can be positive or negative but will always be interpreted as a descent speed
void AC_PosControl::set_max_speed_accel_z(float speed_down, float speed_up, float accel_cmss)
{
    // ensure speed_down is always negative
    speed_down = -fabsf(speed_down);

    // exit immediately if no change in speed up or down
    if (is_equal(_vel_max_down_cms, speed_down) && is_equal(_vel_max_up_cms, speed_up) && is_equal(_accel_max_z_cmss, accel_cmss)) {
        return;
    }

    // sanity check and update
    if (is_negative(speed_down)) {
        _vel_max_down_cms = speed_down;
    }
    if (is_positive(speed_up)) {
        _vel_max_up_cms = speed_up;
    }
    if (is_positive(accel_cmss)) {
        _accel_max_z_cmss = accel_cmss;
    }
    // define maximum position error and maximum first and second differential limits
    _p_pos_z.set_limits(-fabsf(_vel_max_down_cms), _vel_max_up_cms, _accel_max_z_cmss, 0.0f);

    // ensure the vertical time constant is not less than the filters in the _pid_accel_z object
    _tc_z_s = _shaping_tc_z_s;
    if (is_positive(_pid_accel_z.filt_T_hz())) {
        _tc_z_s = MAX(_tc_z_s, 2.0f/(M_2PI*_pid_accel_z.filt_T_hz()));
    }
    if (is_positive(_pid_accel_z.filt_E_hz())) {
        _tc_z_s = MAX(_tc_z_s, 2.0f/(M_2PI*_pid_accel_z.filt_E_hz()));
    }
}

/// init_z_controller - initialise the position controller to the current position, velocity, acceleration and attitude.
///     This function is the default initialisation for any position control that provides position, velocity and acceleration.
void AC_PosControl::init_z_controller()
{
    // Initialise the position controller to the current position, velocity and acceleration.
    init_z();

    // Set accel PID I term based on the current throttle
    _pid_accel_z.set_integrator((_attitude_control.get_throttle_in() - _motors.get_throttle_hover()) * 1000.0f);
}

/// init_z_controller - initialise the position controller to the current position, velocity, acceleration and attitude.
///     This function is the default initialisation for any position control that provides position, velocity and acceleration.
///     This function does not allow any negative velocity or acceleration
void AC_PosControl::init_z_controller_no_descent()
{
    // Initialise the position controller to the current throttle, position, velocity and acceleration.
    init_z_controller();

    // remove all descent if present
    _vel_desired.z = MAX(0.0f, _vel_desired.z);
    _vel_target.z = MAX(0.0f, _vel_target.z);
    _accel_desired.z = MAX(GRAVITY_MSS * 100.0f, _accel_desired.z);
    _accel_target.z = MAX(GRAVITY_MSS * 100.0f, _accel_target.z);
}

/// init_z_controller_stopping_point - initialise the position controller to the stopping point with zero velocity and acceleration.
///     This function should be used when the expected kinimatic path assumes a stationary initial condition but does not specify a specific starting position.
///     The starting position can be retrieved by getting the position target using get_pos_target_cm() after calling this function.
void AC_PosControl::init_z_controller_stopping_point()
{
    // Initialise the position controller to the current throttle, position, velocity and acceleration.
    init_z_controller();

    get_stopping_point_z_cm(_pos_target);
    _vel_target.z = 0.0f;

    // Set accel PID I term based on the current throttle
    _pid_accel_z.set_integrator((_attitude_control.get_throttle_in() - _motors.get_throttle_hover()) * 1000.0f);
}

// relax_z_controller - initialise the position controller to the current position and velocity with decaying acceleration.
///     This function decays the output acceleration by 95% every half second to achieve a smooth transition to zero requested acceleration.
void AC_PosControl::relax_z_controller(float throttle_setting)
{
    // Initialise the position controller to the current position, velocity and acceleration.
    init_z();

    // Set accel PID I term based on the requested throttle
    float throttle = _attitude_control.get_throttle_in();
    throttle_setting = throttle + (throttle_setting - throttle) * (_dt / (_dt + POSCONTROL_RELAX_TC));
    _pid_accel_z.set_integrator((throttle_setting - _motors.get_throttle_hover()) * 1000.0f);
}

/// init_z - initialise the position controller to the current position, velocity and acceleration.
///     This function is private and contains all the shared z axis initialisation functions
void AC_PosControl::init_z()
{
    const Vector3f curr_pos = _inav.get_position();
    _pos_target.z = curr_pos.z;

    const Vector3f &curr_vel = _inav.get_velocity();
    _vel_desired.z = curr_vel.z;
    _vel_target.z = curr_vel.z;

    const Vector3f &curr_accel = _ahrs.get_accel_ef_blended();

    // Reset I term of velocity PID
    _pid_vel_z.reset_filter();
    _pid_vel_z.set_integrator(0.0f);

    _accel_desired.z = -(curr_accel.z + GRAVITY_MSS) * 100.0f;
    _accel_target.z = -(curr_accel.z + GRAVITY_MSS) * 100.0f;
    _pid_accel_z.reset_filter();

    // initialise ekf z reset handler
    init_ekf_z_reset();

    // initialise z_controller time out
    _last_update_z_us = AP_HAL::micros64();
}

/// input_vel_accel_z - calculate a jerk limited path from the current position, velocity and acceleration to an input velocity and acceleration.
///     The vel is projected forwards in time based on a time step of dt and acceleration accel.
///     The function takes the current position, velocity, and acceleration and calculates the required jerk limited adjustment to the acceleration for the next time dt.
///     The kinematic path is constrained by the maximum acceleration and time constant set using the function set_max_speed_accel_z and time constant.
///     The time constant defines the acceleration error decay in the kinematic path as the system approaches constant acceleration.
///     The time constant also defines the time taken to achieve the maximum acceleration.
void AC_PosControl::input_vel_accel_z(Vector3f& vel, const Vector3f& accel, bool force_descend)
{
    // check for ekf z position reset
    handle_ekf_z_reset();

    if (force_descend) {
        // turn off limits in the negative z direction
        _limit_vector.z = MAX(_limit_vector.z, 0.0f);
    }

    // calculated increased maximum acceleration if over speed
    float accel_z_cmss = _accel_max_z_cmss;
    if (_vel_desired.z < _vel_max_down_cms && !is_zero(_vel_max_down_cms)) {
        accel_z_cmss *= POSCONTROL_OVERSPEED_GAIN_Z * _vel_desired.z / _vel_max_down_cms;
    }
    if (_vel_desired.z > _vel_max_up_cms && !is_zero(_vel_max_up_cms)) {
        accel_z_cmss *= POSCONTROL_OVERSPEED_GAIN_Z * _vel_desired.z / _vel_max_up_cms;
    }

    // adjust desired alt if motors have not hit their limits
    update_pos_vel_accel_z(_pos_target, _vel_desired, _accel_desired, _dt, _limit_vector);

    shape_vel_accel_z(vel, accel,
        _vel_desired, _accel_desired,
        _vel_max_down_cms, _vel_max_up_cms,
        -constrain_float(accel_z_cmss, 0.0f, 750.0f), accel_z_cmss,
        _tc_z_s, _dt);

    update_vel_accel_z(vel, accel, _dt, Vector3f());
}

/// set_pos_target_z_from_climb_rate_cm - adjusts target up or down using a commanded climb rate in cm/s
///     using the default position control kinimatic path.
void AC_PosControl::set_pos_target_z_from_climb_rate_cm(const float vel, bool force_descend)
{
    Vector3f vel_3f = Vector3f{0.0f, 0.0f, vel};
    input_vel_accel_z(vel_3f, Vector3f{0.0f, 0.0f, 0.0f}, force_descend);
}

/// input_pos_vel_accel_z - calculate a jerk limited path from the current position, velocity and acceleration to an input position velocity and acceleration.
///     The pos and vel are projected forwards in time based on a time step of dt and acceleration accel.
///     The function takes the current position, velocity, and acceleration and calculates the required jerk limited adjustment to the acceleration for the next time dt.
///     The kinematic path is constrained by the maximum acceleration and time constant set using the function set_max_speed_accel_z and time constant.
///     The time constant defines the acceleration error decay in the kinematic path as the system approaches constant acceleration.
///     The time constant also defines the time taken to achieve the maximum acceleration.
void AC_PosControl::input_pos_vel_accel_z(Vector3f& pos, Vector3f& vel, const Vector3f& accel)
{
    // check for ekf z position reset
    handle_ekf_z_reset();

    // calculated increased maximum acceleration if over speed
    float accel_z_cmss = _accel_max_z_cmss;
    if (_vel_desired.z < _vel_max_down_cms && !is_zero(_vel_max_down_cms)) {
        accel_z_cmss *= POSCONTROL_OVERSPEED_GAIN_Z * _vel_desired.z / _vel_max_down_cms;
    }
    if (_vel_desired.z > _vel_max_up_cms && !is_zero(_vel_max_up_cms)) {
        accel_z_cmss *= POSCONTROL_OVERSPEED_GAIN_Z * _vel_desired.z / _vel_max_up_cms;
    }

    // adjust desired alt if motors have not hit their limits
    update_pos_vel_accel_z(_pos_target, _vel_desired, _accel_desired, _dt, _limit_vector);

    shape_pos_vel_accel_z(pos, vel, accel,
        _pos_target, _vel_desired, _accel_desired,
        0.0f, _vel_max_down_cms, _vel_max_up_cms,
        -constrain_float(accel_z_cmss, 0.0f, 750.0f), accel_z_cmss,
        _tc_z_s, _dt);

    update_pos_vel_accel_z(pos, vel, accel, _dt, Vector3f());
}

/// set_alt_target_with_slew - adjusts target up or down using a commanded altitude in cm
///     using the default position control kinimatic path.
void AC_PosControl::set_alt_target_with_slew(const float& pos)
{
    Vector3f pos_3f = Vector3f{0.0f, 0.0f, pos};
    Vector3f zero;
    input_pos_vel_accel_z(pos_3f, zero, zero);
}

// is_active_z - returns true if the z position controller has been run in the previous 5 loop times
bool AC_PosControl::is_active_z() const
{
    return ((AP_HAL::micros64() - _last_update_z_us) <= _dt * 5000000.0);
}

/// update_z_controller - runs the vertical position controller correcting position, velocity and acceleration errors.
///     Position and velocity errors are converted to velocity and acceleration targets using PID objects
///     Desired velocity and accelerations are added to these corrections as they are calculated
///     Kinematically consistent target position and desired velocity and accelerations should be provided before calling this function
void AC_PosControl::update_z_controller()
{
    // Check for z_controller time out
    if (!is_active_z()) {
        init_z_controller();
        if (has_good_timing()) {
            // call internal error because initialisation has not been done
            INTERNAL_ERROR(AP_InternalError::error_t::flow_of_control);
        }
    }
    _last_update_z_us = AP_HAL::micros64();

    const float curr_alt = _inav.get_position().z;
    // calculate the target velocity correction
    _vel_target.z = _p_pos_z.update_all(_pos_target.z, curr_alt, _limit.pos_down, _limit.pos_up);

    // add feed forward component
    _vel_target.z += _vel_desired.z;

    // Velocity Controller

    const Vector3f& curr_vel = _inav.get_velocity();
    _accel_target.z = _pid_vel_z.update_all(_vel_target.z, curr_vel.z, _motors.limit.throttle_lower, _motors.limit.throttle_upper);

    _accel_target.z += _accel_desired.z;

    // Acceleration Controller

    // Calculate vertical acceleration
    const float z_accel_meas = get_z_accel_cmss();

    // ensure imax is always large enough to overpower hover throttle
    if (_motors.get_throttle_hover() * 1000.0f > _pid_accel_z.imax()) {
        _pid_accel_z.imax(_motors.get_throttle_hover() * 1000.0f);
    }
    float thr_out;
    if (_vibe_comp_enabled) {
        thr_out = get_throttle_with_vibration_override();
    } else {
        thr_out = _pid_accel_z.update_all(_accel_target.z, z_accel_meas, (_motors.limit.throttle_lower || _motors.limit.throttle_upper)) * 0.001f;
        thr_out += _pid_accel_z.get_ff() * 0.001f;
    }
    thr_out += _motors.get_throttle_hover();

    // Actuator commands

    // send throttle to attitude controller with angle boost
    _attitude_control.set_throttle_out(thr_out, true, POSCONTROL_THROTTLE_CUTOFF_FREQ_HZ);

    // Check for vertical controller health

    // _speed_down_cms is checked to be non-zero when set
    float error_ratio = _vel_error.z / _vel_max_down_cms;
    _vel_z_control_ratio += _dt * 0.1f * (0.5 - error_ratio);
    _vel_z_control_ratio = constrain_float(_vel_z_control_ratio, 0.0f, 2.0f);

    // set vertical component of the limit vector
    if (_motors.limit.throttle_upper) {
        _limit_vector.z = 1.0f;
    } else if (_motors.limit.throttle_lower) {
        _limit_vector.z = -1.0f;
    } else {
        _limit_vector.z = 0.0f;
    }
}


///
/// Accessors
///

/// get_stopping_point_z_cm - calculates stopping point in NEU cm based on current position, velocity, vehicle acceleration
void AC_PosControl::get_stopping_point_z_cm(Vector3f& stopping_point) const
{
    const float curr_pos_z = _inav.get_position().z;
    float curr_vel_z = _inav.get_velocity().z;

    // if position controller is active add current velocity error to avoid sudden jump in acceleration
    if (is_active_z()) {
        curr_vel_z -= _vel_desired.z;
    }

    // avoid divide by zero by using current position if kP is very low or acceleration is zero
    if (!is_positive(_p_pos_z.kP()) || !is_positive(_accel_max_z_cmss)) {
        stopping_point.z = curr_pos_z;
        return;
    }

    stopping_point.z = curr_pos_z + constrain_float(stopping_distance(curr_vel_z, _p_pos_z.kP(), _accel_max_z_cmss), - POSCONTROL_STOPPING_DIST_DOWN_MAX, POSCONTROL_STOPPING_DIST_UP_MAX);
}

/// get_lean_angle_max_cd - returns the maximum lean angle the autopilot may request
float AC_PosControl::get_lean_angle_max_cd() const
{
    if (is_zero(_lean_angle_max)) {
        return _attitude_control.lean_angle_max();
    }
    return _lean_angle_max * 100.0f;
}

/// set position, velocity and acceleration targets
void AC_PosControl::set_pos_vel_accel(const Vector3f& pos, const Vector3f& vel, const Vector3f& accel)
{
    _pos_target = pos;
    _vel_desired = vel;
    _accel_desired = accel;
}

/// set position, velocity and acceleration targets
void AC_PosControl::set_pos_vel_accel_xy(const Vector2f& pos, const Vector2f& vel, const Vector2f& accel)
{
    _pos_target.x = pos.x;
    _pos_target.y = pos.y;
    _vel_desired.x = vel.x;
    _vel_desired.y = vel.y;
    _accel_desired.x = accel.x;
    _accel_desired.y = accel.y;
}

// get_lean_angles_to_accel - convert roll, pitch lean target angles to lat/lon frame accelerations in cm/s/s
Vector3f AC_PosControl::lean_angles_to_accel(const Vector3f& att_target_euler) const
{
    // rotate our roll, pitch angles into lat/lon frame
    const float sin_roll = sinf(att_target_euler.x);
    const float cos_roll = cosf(att_target_euler.x);
    const float sin_pitch = sinf(att_target_euler.y);
    const float cos_pitch = cosf(att_target_euler.y);
    const float sin_yaw = sinf(att_target_euler.z);
    const float cos_yaw = cosf(att_target_euler.z);

    return Vector3f{
        (GRAVITY_MSS * 100) * (-cos_yaw * sin_pitch * cos_roll - sin_yaw * sin_roll) / MAX(cos_roll * cos_pitch, 0.1f),
        (GRAVITY_MSS * 100) * (-sin_yaw * sin_pitch * cos_roll + cos_yaw * sin_roll) / MAX(cos_roll * cos_pitch, 0.1f),
        (GRAVITY_MSS * 100)
    };
}

// returns the NED target acceleration vector for attitude control
Vector3f AC_PosControl::get_thrust_vector() const
{
    Vector3f accel_target = get_accel_target_cmss();
    accel_target.z = -GRAVITY_MSS * 100.0f;
    return accel_target;
}

/// get_stopping_point_xy_cm - calculates stopping point in NEU cm based on current position, velocity, vehicle acceleration
///    function does not change the z axis
void AC_PosControl::get_stopping_point_xy_cm(Vector3f &stopping_point) const
{
    const Vector3f curr_pos = _inav.get_position();
    stopping_point.x = curr_pos.x;
    stopping_point.y = curr_pos.y;
    float kP = _p_pos_xy.kP();

    Vector3f curr_vel = _inav.get_velocity();

    // add velocity error to current velocity
    if (is_active_xy()) {
        curr_vel.x += _vel_error.x;
        curr_vel.y += _vel_error.y;
    }

    // calculate current velocity
    float vel_total = norm(curr_vel.x, curr_vel.y);

    if (!is_positive(vel_total)) {
        return;
    }

    const float stopping_dist = stopping_distance(constrain_float(vel_total, 0.0, _vel_max_xy_cms), kP, _accel_max_xy_cmss);
    if (!is_positive(stopping_dist)) {
        return;
    }

    // convert the stopping distance into a stopping point using velocity vector
    const float t = stopping_dist / vel_total;
    stopping_point.x += t * curr_vel.x;
    stopping_point.y += t * curr_vel.y;
}

/// get_bearing_to_target_cd - get bearing to target position in centi-degrees
int32_t AC_PosControl::get_bearing_to_target_cd() const
{
    return get_bearing_cd(_inav.get_position(), _pos_target);
}


///
/// System methods
///

// get throttle using vibration-resistant calculation (uses feed forward with manually calculated gain)
float AC_PosControl::get_throttle_with_vibration_override()
{
    _accel_desired.z = 0.0f;
    const float thr_per_accelz_cmss = _motors.get_throttle_hover() / (GRAVITY_MSS * 100.0f);
    // during vibration compensation use feed forward with manually calculated gain
    // ToDo: clear pid_info P, I and D terms for logging
    if (!(_motors.limit.throttle_lower || _motors.limit.throttle_upper) || ((is_positive(_pid_accel_z.get_i()) && is_negative(_vel_error.z)) || (is_negative(_pid_accel_z.get_i()) && is_positive(_vel_error.z)))) {
        _pid_accel_z.set_integrator(_pid_accel_z.get_i() + _dt * thr_per_accelz_cmss * 1000.0f * _vel_error.z * _pid_vel_z.kP() * POSCONTROL_VIBE_COMP_I_GAIN);
    }
    return POSCONTROL_VIBE_COMP_P_GAIN * thr_per_accelz_cmss * _accel_target.z + _pid_accel_z.get_i() * 0.001f;
}

/// standby_xyz_reset - resets I terms and removes position error
///     This function will let Loiter and Alt Hold continue to operate
///     in the event that the flight controller is in control of the
///     aircraft when in standby.
void AC_PosControl::standby_xyz_reset()
{
    // Set _pid_accel_z integrator to zero.
    _pid_accel_z.set_integrator(0.0f);

    // Set the target position to the current pos.
    _pos_target = _inav.get_position();

    // Set _pid_vel_xy integrator and derivative to zero.
    _pid_vel_xy.reset_filter();

    // initialise ekf xy reset handler
    init_ekf_xy_reset();
}

// write PSC and/or PSCZ logs
void AC_PosControl::write_log()
{
    if (is_active_xy()) {
        float accel_x, accel_y;
        lean_angles_to_accel_xy(accel_x, accel_y);
        AP::logger().Write_PSC(get_pos_target_cm(), _inav.get_position(), get_vel_target_cms(), _inav.get_velocity(), get_accel_target_cmss(), accel_x, accel_y);
    }

    if (is_active_z()) {
        AP::logger().Write_PSCZ(get_pos_target_cm().z, _inav.get_position().z,
                                get_vel_desired_cms().z, get_vel_target_cms().z, _inav.get_velocity().z,
                                _accel_desired.z, get_accel_target_cmss().z, get_z_accel_cmss(), _attitude_control.get_throttle_in());
    }
}

///
/// private methods
///

// get_lean_angles_to_accel - convert roll, pitch lean angles to NE frame accelerations in cm/s/s
void AC_PosControl::accel_to_lean_angles(float accel_x_cmss, float accel_y_cmss, float& roll_target, float& pitch_target) const
{
    // rotate accelerations into body forward-right frame
    const float accel_forward = accel_x_cmss * _ahrs.cos_yaw() + accel_y_cmss * _ahrs.sin_yaw();
    const float accel_right = -accel_x_cmss * _ahrs.sin_yaw() + accel_y_cmss * _ahrs.cos_yaw();

    // update angle targets that will be passed to stabilize controller
    pitch_target = atanf(-accel_forward / (GRAVITY_MSS * 100.0f)) * (18000.0f / M_PI);
    float cos_pitch_target = cosf(pitch_target * M_PI / 18000.0f);
    roll_target = atanf(accel_right * cos_pitch_target / (GRAVITY_MSS * 100.0f)) * (18000.0f / M_PI);
}

// lean_angles_to_accel_xy - convert roll, pitch lean target angles to NE frame accelerations in cm/s/s
// todo: this should be based on thrust vector attitude control
void AC_PosControl::lean_angles_to_accel_xy(float& accel_x_cmss, float& accel_y_cmss) const
{
    // rotate our roll, pitch angles into lat/lon frame
    Vector3f att_target_euler = _attitude_control.get_att_target_euler_rad();
    att_target_euler.z = _ahrs.yaw;
    Vector3f accel_cmss = lean_angles_to_accel(att_target_euler);

    accel_x_cmss = accel_cmss.x;
    accel_y_cmss = accel_cmss.y;
}

// calculate_yaw_and_rate_yaw - update the calculated the vehicle yaw and rate of yaw.
bool AC_PosControl::calculate_yaw_and_rate_yaw()
{
    // Calculate the turn rate
    float turn_rate = 0.0f;
    const Vector2f vel_desired_xy(_vel_desired.x, _vel_desired.y);
    const Vector2f accel_desired_xy(_accel_desired.x, _accel_desired.y);
    const float vel_desired_xy_len = vel_desired_xy.length();
    if (is_positive(vel_desired_xy_len)) {
        const float accel_forward = (accel_desired_xy.x * vel_desired_xy.x + accel_desired_xy.y * vel_desired_xy.y)/vel_desired_xy_len;
        const Vector2f accel_turn = accel_desired_xy - vel_desired_xy * accel_forward / vel_desired_xy_len;
        const float accel_turn_xy_len = accel_turn.length();
        turn_rate = accel_turn_xy_len / vel_desired_xy_len;
        if ((accel_turn.y * vel_desired_xy.x - accel_turn.x * vel_desired_xy.y) < 0.0) {
            turn_rate = -turn_rate;
        }
    }

    // update the target yaw if origin and destination are at least 2m apart horizontally
    if (vel_desired_xy_len > _vel_max_xy_cms * 0.05f) {
        _yaw_target = degrees(vel_desired_xy.angle()) * 100.0f;
        _yaw_rate_target = turn_rate*degrees(100.0f);
        return true;
    }
    return false;
}

/// initialise ekf xy position reset check
void AC_PosControl::init_ekf_xy_reset()
{
    Vector2f pos_shift;
    _ekf_xy_reset_ms = _ahrs.getLastPosNorthEastReset(pos_shift);
}

/// handle_ekf_xy_reset - check for ekf position reset and adjust loiter or brake target position
void AC_PosControl::handle_ekf_xy_reset()
{
    // check for position shift
    Vector2f pos_shift;
    uint32_t reset_ms = _ahrs.getLastPosNorthEastReset(pos_shift);
    if (reset_ms != _ekf_xy_reset_ms) {

        const Vector3f& curr_pos = _inav.get_position();
        _pos_target.x = curr_pos.x + _p_pos_xy.get_error().x;
        _pos_target.y = curr_pos.y + _p_pos_xy.get_error().y;

        const Vector3f& curr_vel = _inav.get_velocity();
        _vel_target.x = curr_vel.x + _pid_vel_xy.get_error().x;
        _vel_target.y = curr_vel.y + _pid_vel_xy.get_error().y;

        _ekf_xy_reset_ms = reset_ms;
    }
}

/// initialise ekf z axis reset check
void AC_PosControl::init_ekf_z_reset()
{
    float alt_shift;
    _ekf_z_reset_ms = _ahrs.getLastPosDownReset(alt_shift);
}

/// handle_ekf_z_reset - check for ekf position reset and adjust loiter or brake target position
void AC_PosControl::handle_ekf_z_reset()
{
    // check for position shift
    float alt_shift;
    uint32_t reset_ms = _ahrs.getLastPosDownReset(alt_shift);
    if (reset_ms != 0 && reset_ms != _ekf_z_reset_ms) {

        const Vector3f& curr_pos = _inav.get_position();
        _pos_target.z = curr_pos.z + _p_pos_z.get_error();

        const Vector3f& curr_vel = _inav.get_velocity();
        _vel_target.z = curr_vel.z + _pid_vel_z.get_error();

        _ekf_z_reset_ms = reset_ms;
    }
}

bool AC_PosControl::pre_arm_checks(const char *param_prefix,
                                   char *failure_msg,
                                   const uint8_t failure_msg_len)
{
    if (!is_positive(get_pos_xy_p().kP())) {
        hal.util->snprintf(failure_msg, failure_msg_len, "%s_POSXY_P must be > 0", param_prefix);
        return false;
    }
    if (!is_positive(get_pos_z_p().kP())) {
        hal.util->snprintf(failure_msg, failure_msg_len, "%s_POSZ_P must be > 0", param_prefix);
        return false;
    }
    if (!is_positive(get_vel_z_pid().kP())) {
        hal.util->snprintf(failure_msg, failure_msg_len, "%s_VELZ_P must be > 0", param_prefix);
        return false;
    }
    if (!is_positive(get_accel_z_pid().kP())) {
        hal.util->snprintf(failure_msg, failure_msg_len, "%s_ACCZ_P must be > 0", param_prefix);
        return false;
    }
    if (!is_positive(get_accel_z_pid().kI())) {
        hal.util->snprintf(failure_msg, failure_msg_len, "%s_ACCZ_I must be > 0", param_prefix);
        return false;
    }

    return true;
}

// return true if on a real vehicle or SITL with lock-step scheduling
bool AC_PosControl::has_good_timing(void) const
{
#if CONFIG_HAL_BOARD == HAL_BOARD_SITL
    auto *sitl = AP::sitl();
    if (sitl) {
        return sitl->state.is_lock_step_scheduled;
    }
#endif
    // real boards are assumed to have good timing
    return true;
}