#pragma once

#include <AP_HAL/AP_HAL_Boards.h>
#include <AP_Relay/AP_Relay_config.h>

#ifndef HAL_GCS_ENABLED
#define HAL_GCS_ENABLED 1
#endif

#ifndef HAL_MAVLINK_BINDINGS_ENABLED
#define HAL_MAVLINK_BINDINGS_ENABLED HAL_GCS_ENABLED
#endif

// BATTERY2 is slated to be removed:
#ifndef AP_MAVLINK_BATTERY2_ENABLED
#define AP_MAVLINK_BATTERY2_ENABLED 1
#endif

#ifndef HAL_HIGH_LATENCY2_ENABLED
#define HAL_HIGH_LATENCY2_ENABLED 1
#endif

// handling of MISSION_SET_CURRENT (the message) is slated to be
// removed.  It has signficant deficiencies vs MAV_CMD_DO_SET_CURRENT.
// The command was added to the spec in January 2019 and to MAVLink in
// ArduPilot in 4.1.x
#ifndef AP_MAVLINK_MISSION_SET_CURRENT_ENABLED
#define AP_MAVLINK_MISSION_SET_CURRENT_ENABLED 1
#endif

// AUTOPILOT_VERSION_REQUEST is slated to be removed; an instance of
// AUTOPILOT_VERSION can be requested with MAV_CMD_REQUEST_MESSAGE,
// which gets you an ACK/NACK
#ifndef AP_MAVLINK_AUTOPILOT_VERSION_REQUEST_ENABLED
#define AP_MAVLINK_AUTOPILOT_VERSION_REQUEST_ENABLED 1
#endif

// handling of MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES is slated to be
// removed; the message can be requested with MAV_CMD_REQUEST_MESSAGE
#ifndef AP_MAVLINK_MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES_ENABLED
#define AP_MAVLINK_MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES_ENABLED 1
#endif

#ifndef HAL_MAVLINK_INTERVALS_FROM_FILES_ENABLED
#define HAL_MAVLINK_INTERVALS_FROM_FILES_ENABLED ((AP_FILESYSTEM_FATFS_ENABLED || AP_FILESYSTEM_POSIX_ENABLED) && BOARD_FLASH_SIZE > 1024)
#endif

#ifndef AP_MAVLINK_MSG_RELAY_STATUS_ENABLED
#define AP_MAVLINK_MSG_RELAY_STATUS_ENABLED HAL_GCS_ENABLED && AP_RELAY_ENABLED
#endif

// allow removal of developer-centric mavlink commands
#ifndef AP_MAVLINK_FAILURE_CREATION_ENABLED
#define AP_MAVLINK_FAILURE_CREATION_ENABLED 1
#endif

#ifndef AP_MAVLINK_RALLY_POINT_PROTOCOL_ENABLED
#define AP_MAVLINK_RALLY_POINT_PROTOCOL_ENABLED HAL_GCS_ENABLED && HAL_RALLY_ENABLED
#endif

#ifndef AP_MAVLINK_MSG_MOUNT_CONFIGURE_ENABLED
#define AP_MAVLINK_MSG_MOUNT_CONFIGURE_ENABLED HAL_GCS_ENABLED
#endif

#ifndef AP_MAVLINK_MSG_MOUNT_CONTROL_ENABLED
#define AP_MAVLINK_MSG_MOUNT_CONTROL_ENABLED HAL_GCS_ENABLED
#endif

// this is for both read and write messages:
#ifndef AP_MAVLINK_MSG_DEVICE_OP_ENABLED
#define AP_MAVLINK_MSG_DEVICE_OP_ENABLED HAL_GCS_ENABLED
#endif

#ifndef AP_MAVLINK_SERVO_RELAY_ENABLED
#define AP_MAVLINK_SERVO_RELAY_ENABLED HAL_GCS_ENABLED && AP_SERVORELAYEVENTS_ENABLED
#endif

#ifndef AP_MAVLINK_MSG_SERIAL_CONTROL_ENABLED
#define AP_MAVLINK_MSG_SERIAL_CONTROL_ENABLED HAL_GCS_ENABLED
#endif

#ifndef AP_MAVLINK_MSG_UAVIONIX_ADSB_OUT_STATUS_ENABLED
#define AP_MAVLINK_MSG_UAVIONIX_ADSB_OUT_STATUS_ENABLED HAL_ADSB_ENABLED
#endif

// GCS should be using MISSION_REQUEST_INT instead; this is a waste of
// flash.  MISSION_REQUEST was deprecated in June 2020.  We started
// sending warnings to the GCS in Sep 2022 if this command was used.
// Copter 4.4.0 sends this warning.
#ifndef AP_MAVLINK_MSG_MISSION_REQUEST_ENABLED
#define AP_MAVLINK_MSG_MISSION_REQUEST_ENABLED 1
#endif

// all commands can be executed by COMMAND_INT, so COMMAND_LONG isn't
// strictly required.  This option created for 4.5, Nov 2023, and code
// left in place.
#ifndef AP_MAVLINK_COMMAND_LONG_ENABLED
#define AP_MAVLINK_COMMAND_LONG_ENABLED 1
#endif