// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*- // default sensors are present and healthy: gyro, accelerometer, barometer, rate_control, attitude_stabilization, yaw_position, altitude control, x/y position control, motor_control #define MAVLINK_SENSOR_PRESENT_DEFAULT (MAV_SYS_STATUS_SENSOR_3D_GYRO | MAV_SYS_STATUS_SENSOR_3D_ACCEL | MAV_SYS_STATUS_SENSOR_ABSOLUTE_PRESSURE | MAV_SYS_STATUS_SENSOR_ANGULAR_RATE_CONTROL | MAV_SYS_STATUS_SENSOR_ATTITUDE_STABILIZATION | MAV_SYS_STATUS_SENSOR_YAW_POSITION | MAV_SYS_STATUS_SENSOR_Z_ALTITUDE_CONTROL | MAV_SYS_STATUS_SENSOR_XY_POSITION_CONTROL | MAV_SYS_STATUS_SENSOR_MOTOR_OUTPUTS) // use this to prevent recursion during sensor init static bool in_mavlink_delay; // true when we have received at least 1 MAVLink packet static bool mavlink_active; // true if we are out of time in our event timeslice static bool gcs_out_of_time; // check if a message will fit in the payload space available #define CHECK_PAYLOAD_SIZE(id) if (payload_space < MAVLINK_MSG_ID_ ## id ## _LEN) return false /* * !!NOTE!! * * the use of NOINLINE separate functions for each message type avoids * a compiler bug in gcc that would cause it to use far more stack * space than is needed. Without the NOINLINE we use the sum of the * stack needed for each message type. Please be careful to follow the * pattern below when adding any new messages */ static NOINLINE void send_heartbeat(mavlink_channel_t chan) { uint8_t base_mode = MAV_MODE_FLAG_CUSTOM_MODE_ENABLED; uint8_t system_status = is_flying() ? MAV_STATE_ACTIVE : MAV_STATE_STANDBY; uint32_t custom_mode = control_mode; if (failsafe.state != FAILSAFE_NONE) { system_status = MAV_STATE_CRITICAL; } // work out the base_mode. This value is not very useful // for APM, but we calculate it as best we can so a generic // MAVLink enabled ground station can work out something about // what the MAV is up to. The actual bit values are highly // ambiguous for most of the APM flight modes. In practice, you // only get useful information from the custom_mode, which maps to // the APM flight mode and has a well defined meaning in the // ArduPlane documentation switch (control_mode) { case MANUAL: case TRAINING: case ACRO: base_mode = MAV_MODE_FLAG_MANUAL_INPUT_ENABLED; break; case STABILIZE: case FLY_BY_WIRE_A: case FLY_BY_WIRE_B: case CRUISE: base_mode = MAV_MODE_FLAG_STABILIZE_ENABLED; break; case AUTO: case RTL: case LOITER: case GUIDED: case CIRCLE: base_mode = MAV_MODE_FLAG_GUIDED_ENABLED | MAV_MODE_FLAG_STABILIZE_ENABLED; // note that MAV_MODE_FLAG_AUTO_ENABLED does not match what // APM does in any mode, as that is defined as "system finds its own goal // positions", which APM does not currently do break; case INITIALISING: system_status = MAV_STATE_CALIBRATING; break; } if (!training_manual_pitch || !training_manual_roll) { base_mode |= MAV_MODE_FLAG_STABILIZE_ENABLED; } if (control_mode != MANUAL && control_mode != INITIALISING) { // stabiliser of some form is enabled base_mode |= MAV_MODE_FLAG_STABILIZE_ENABLED; } if (g.stick_mixing != STICK_MIXING_DISABLED && control_mode != INITIALISING) { // all modes except INITIALISING have some form of manual // override if stick mixing is enabled base_mode |= MAV_MODE_FLAG_MANUAL_INPUT_ENABLED; } #if HIL_MODE != HIL_MODE_DISABLED base_mode |= MAV_MODE_FLAG_HIL_ENABLED; #endif // we are armed if we are not initialising if (control_mode != INITIALISING && ahrs.get_armed()) { base_mode |= MAV_MODE_FLAG_SAFETY_ARMED; } // indicate we have set a custom mode base_mode |= MAV_MODE_FLAG_CUSTOM_MODE_ENABLED; mavlink_msg_heartbeat_send( chan, MAV_TYPE_FIXED_WING, MAV_AUTOPILOT_ARDUPILOTMEGA, base_mode, custom_mode, system_status); } static NOINLINE void send_attitude(mavlink_channel_t chan) { Vector3f omega = ahrs.get_gyro(); mavlink_msg_attitude_send( chan, millis(), ahrs.roll, ahrs.pitch - radians(g.pitch_trim_cd*0.01), ahrs.yaw, omega.x, omega.y, omega.z); } #if GEOFENCE_ENABLED == ENABLED static NOINLINE void send_fence_status(mavlink_channel_t chan) { geofence_send_status(chan); } #endif static NOINLINE void send_extended_status1(mavlink_channel_t chan) { uint32_t control_sensors_present; uint32_t control_sensors_enabled; uint32_t control_sensors_health; // default sensors present control_sensors_present = MAVLINK_SENSOR_PRESENT_DEFAULT; // first what sensors/controllers we have if (g.compass_enabled) { control_sensors_present |= MAV_SYS_STATUS_SENSOR_3D_MAG; // compass present } if (airspeed.enabled()) { control_sensors_present |= MAV_SYS_STATUS_SENSOR_DIFFERENTIAL_PRESSURE; } if (gps.status() > AP_GPS::NO_GPS) { control_sensors_present |= MAV_SYS_STATUS_SENSOR_GPS; } if (geofence_present()) { control_sensors_present |= MAV_SYS_STATUS_GEOFENCE; } // all present sensors enabled by default except rate control, attitude stabilization, yaw, altitude, position control, geofence and motor output which we will set individually control_sensors_enabled = control_sensors_present & (~MAV_SYS_STATUS_SENSOR_ANGULAR_RATE_CONTROL & ~MAV_SYS_STATUS_SENSOR_ATTITUDE_STABILIZATION & ~MAV_SYS_STATUS_SENSOR_YAW_POSITION & ~MAV_SYS_STATUS_SENSOR_Z_ALTITUDE_CONTROL & ~MAV_SYS_STATUS_SENSOR_XY_POSITION_CONTROL & ~MAV_SYS_STATUS_SENSOR_MOTOR_OUTPUTS & ~MAV_SYS_STATUS_GEOFENCE); if (airspeed.enabled() && airspeed.use()) { control_sensors_enabled |= MAV_SYS_STATUS_SENSOR_DIFFERENTIAL_PRESSURE; } if (geofence_enabled()) { control_sensors_enabled |= MAV_SYS_STATUS_GEOFENCE; } switch (control_mode) { case MANUAL: break; case ACRO: control_sensors_enabled |= MAV_SYS_STATUS_SENSOR_ANGULAR_RATE_CONTROL; // 3D angular rate control break; case STABILIZE: case FLY_BY_WIRE_A: control_sensors_enabled |= MAV_SYS_STATUS_SENSOR_ANGULAR_RATE_CONTROL; // 3D angular rate control control_sensors_enabled |= MAV_SYS_STATUS_SENSOR_ATTITUDE_STABILIZATION; // attitude stabilisation break; case FLY_BY_WIRE_B: case CRUISE: control_sensors_enabled |= MAV_SYS_STATUS_SENSOR_ANGULAR_RATE_CONTROL; // 3D angular rate control control_sensors_enabled |= MAV_SYS_STATUS_SENSOR_ATTITUDE_STABILIZATION; // attitude stabilisation control_sensors_enabled |= MAV_SYS_STATUS_SENSOR_MOTOR_OUTPUTS; // motor control break; case TRAINING: if (!training_manual_roll || !training_manual_pitch) { control_sensors_enabled |= MAV_SYS_STATUS_SENSOR_ANGULAR_RATE_CONTROL; // 3D angular rate control control_sensors_enabled |= MAV_SYS_STATUS_SENSOR_ATTITUDE_STABILIZATION; // attitude stabilisation } break; case AUTO: case RTL: case LOITER: case GUIDED: case CIRCLE: control_sensors_enabled |= MAV_SYS_STATUS_SENSOR_ANGULAR_RATE_CONTROL; // 3D angular rate control control_sensors_enabled |= MAV_SYS_STATUS_SENSOR_ATTITUDE_STABILIZATION; // attitude stabilisation control_sensors_enabled |= MAV_SYS_STATUS_SENSOR_YAW_POSITION; // yaw position control_sensors_enabled |= MAV_SYS_STATUS_SENSOR_Z_ALTITUDE_CONTROL; // altitude control control_sensors_enabled |= MAV_SYS_STATUS_SENSOR_XY_POSITION_CONTROL; // X/Y position control control_sensors_enabled |= MAV_SYS_STATUS_SENSOR_MOTOR_OUTPUTS; // motor control break; case INITIALISING: break; } // default: all present sensors healthy except 3D_MAG, GPS, DIFFERNTIAL_PRESSURE. GEOFENCE always defaults to healthy. control_sensors_health = control_sensors_present & ~(MAV_SYS_STATUS_SENSOR_3D_MAG | MAV_SYS_STATUS_SENSOR_GPS | MAV_SYS_STATUS_SENSOR_DIFFERENTIAL_PRESSURE); control_sensors_health |= MAV_SYS_STATUS_GEOFENCE; if (g.compass_enabled && compass.healthy(0) && ahrs.use_compass()) { control_sensors_health |= MAV_SYS_STATUS_SENSOR_3D_MAG; } if (gps.status() >= AP_GPS::GPS_OK_FIX_3D) { control_sensors_health |= MAV_SYS_STATUS_SENSOR_GPS; } if (!ins.healthy()) { control_sensors_health &= ~(MAV_SYS_STATUS_SENSOR_3D_GYRO | MAV_SYS_STATUS_SENSOR_3D_ACCEL); } if (airspeed.healthy()) { control_sensors_health |= MAV_SYS_STATUS_SENSOR_DIFFERENTIAL_PRESSURE; } if (geofence_breached()) { control_sensors_health &= ~MAV_SYS_STATUS_GEOFENCE; } int16_t battery_current = -1; int8_t battery_remaining = -1; if (battery.monitoring() == AP_BATT_MONITOR_VOLTAGE_AND_CURRENT) { battery_remaining = battery.capacity_remaining_pct(); battery_current = battery.current_amps() * 100; } mavlink_msg_sys_status_send( chan, control_sensors_present, control_sensors_enabled, control_sensors_health, (uint16_t)(scheduler.load_average(20000) * 1000), battery.voltage() * 1000, // mV battery_current, // in 10mA units battery_remaining, // in % 0, // comm drops %, 0, // comm drops in pkts, 0, 0, 0, 0); } static void NOINLINE send_location(mavlink_channel_t chan) { uint32_t fix_time_ms; // if we have a GPS fix, take the time as the last fix time. That // allows us to correctly calculate velocities and extrapolate // positions. // If we don't have a GPS fix then we are dead reckoning, and will // use the current boot time as the fix time. if (gps.status() >= AP_GPS::GPS_OK_FIX_2D) { fix_time_ms = gps.last_fix_time_ms(); } else { fix_time_ms = hal.scheduler->millis(); } const Vector3f &vel = gps.velocity(); mavlink_msg_global_position_int_send( chan, fix_time_ms, current_loc.lat, // in 1E7 degrees current_loc.lng, // in 1E7 degrees gps.location().alt * 10UL, // millimeters above sea level relative_altitude() * 1.0e3, // millimeters above ground vel.x * 100, // X speed cm/s (+ve North) vel.y * 100, // Y speed cm/s (+ve East) vel.z * -100, // Z speed cm/s (+ve up) ahrs.yaw_sensor); } static void NOINLINE send_nav_controller_output(mavlink_channel_t chan) { mavlink_msg_nav_controller_output_send( chan, nav_roll_cd * 0.01, nav_pitch_cd * 0.01, nav_controller->nav_bearing_cd() * 0.01f, nav_controller->target_bearing_cd() * 0.01f, wp_distance, altitude_error_cm * 0.01, airspeed_error_cm, nav_controller->crosstrack_error()); } static void NOINLINE send_gps_raw(mavlink_channel_t chan) { static uint32_t last_send_time_ms; if (last_send_time_ms == 0 || last_send_time_ms != gps.last_message_time_ms(0)) { last_send_time_ms = gps.last_message_time_ms(0); const Location &loc = gps.location(0); mavlink_msg_gps_raw_int_send( chan, gps.last_fix_time_ms(0)*(uint64_t)1000, gps.status(0), loc.lat, // in 1E7 degrees loc.lng, // in 1E7 degrees loc.alt * 10UL, // in mm gps.get_hdop(0), 65535, gps.ground_speed(0)*100, // cm/s gps.ground_course_cd(0), // 1/100 degrees, gps.num_sats(0)); } #if HAL_CPU_CLASS > HAL_CPU_CLASS_16 static uint32_t last_send_time_ms2; if (gps.num_sensors() > 1 && gps.status(1) > AP_GPS::NO_GPS && (last_send_time_ms2 == 0 || last_send_time_ms2 != gps.last_message_time_ms(1))) { int16_t payload_space = comm_get_txspace(chan) - MAVLINK_NUM_NON_PAYLOAD_BYTES; if (payload_space >= MAVLINK_MSG_ID_GPS2_RAW_LEN) { const Location &loc = gps.location(1); last_send_time_ms = gps.last_message_time_ms(1); mavlink_msg_gps2_raw_send( chan, gps.last_fix_time_ms(1)*(uint64_t)1000, gps.status(1), loc.lat, loc.lng, loc.alt * 10UL, gps.get_hdop(1), 65535, gps.ground_speed(1)*100, // cm/s gps.ground_course_cd(1), // 1/100 degrees, gps.num_sats(1), 0, 0); } } #endif } static void NOINLINE send_system_time(mavlink_channel_t chan) { mavlink_msg_system_time_send( chan, gps.time_epoch_usec(), hal.scheduler->millis()); } #if HIL_MODE != HIL_MODE_DISABLED void NOINLINE send_servo_out(mavlink_channel_t chan) { // normalized values scaled to -10000 to 10000 // This is used for HIL. Do not change without discussing with // HIL maintainers mavlink_msg_rc_channels_scaled_send( chan, millis(), 0, // port 0 10000 * channel_roll->norm_output() * (channel_roll->get_reverse()?-1:1), 10000 * channel_pitch->norm_output() * (channel_pitch->get_reverse()?-1:1), 10000 * channel_throttle->norm_output() * (channel_throttle->get_reverse()?-1:1), 10000 * channel_rudder->norm_output() * (channel_rudder->get_reverse()?-1:1), 0, 0, 0, 0, receiver_rssi); } #endif static void NOINLINE send_radio_in(mavlink_channel_t chan) { mavlink_msg_rc_channels_raw_send( chan, millis(), 0, // port hal.rcin->read(CH_1), hal.rcin->read(CH_2), hal.rcin->read(CH_3), hal.rcin->read(CH_4), hal.rcin->read(CH_5), hal.rcin->read(CH_6), hal.rcin->read(CH_7), hal.rcin->read(CH_8), receiver_rssi); if (hal.rcin->num_channels() > 8 && comm_get_txspace(chan) - MAVLINK_NUM_NON_PAYLOAD_BYTES >= MAVLINK_MSG_ID_RC_CHANNELS_LEN) { mavlink_msg_rc_channels_send( chan, millis(), hal.rcin->num_channels(), hal.rcin->read(CH_1), hal.rcin->read(CH_2), hal.rcin->read(CH_3), hal.rcin->read(CH_4), hal.rcin->read(CH_5), hal.rcin->read(CH_6), hal.rcin->read(CH_7), hal.rcin->read(CH_8), hal.rcin->read(CH_9), hal.rcin->read(CH_10), hal.rcin->read(CH_11), hal.rcin->read(CH_12), hal.rcin->read(CH_13), hal.rcin->read(CH_14), hal.rcin->read(CH_15), hal.rcin->read(CH_16), hal.rcin->read(CH_17), hal.rcin->read(CH_18), receiver_rssi); } } static void NOINLINE send_radio_out(mavlink_channel_t chan) { #if HIL_MODE != HIL_MODE_DISABLED if (!g.hil_servos) { mavlink_msg_servo_output_raw_send( chan, micros(), 0, // port RC_Channel::rc_channel(0)->radio_out, RC_Channel::rc_channel(1)->radio_out, RC_Channel::rc_channel(2)->radio_out, RC_Channel::rc_channel(3)->radio_out, RC_Channel::rc_channel(4)->radio_out, RC_Channel::rc_channel(5)->radio_out, RC_Channel::rc_channel(6)->radio_out, RC_Channel::rc_channel(7)->radio_out); return; } #endif mavlink_msg_servo_output_raw_send( chan, micros(), 0, // port hal.rcout->read(0), hal.rcout->read(1), hal.rcout->read(2), hal.rcout->read(3), hal.rcout->read(4), hal.rcout->read(5), hal.rcout->read(6), hal.rcout->read(7)); } static void NOINLINE send_vfr_hud(mavlink_channel_t chan) { float aspeed; if (airspeed.enabled()) { aspeed = airspeed.get_airspeed(); } else if (!ahrs.airspeed_estimate(&aspeed)) { aspeed = 0; } float throttle_norm = channel_throttle->norm_output() * 100; throttle_norm = constrain_int16(throttle_norm, -100, 100); uint16_t throttle = ((uint16_t)(throttle_norm + 100)) / 2; mavlink_msg_vfr_hud_send( chan, aspeed, gps.ground_speed(), (ahrs.yaw_sensor / 100) % 360, throttle, current_loc.alt / 100.0, barometer.get_climb_rate()); } static void NOINLINE send_raw_imu1(mavlink_channel_t chan) { const Vector3f &accel = ins.get_accel(); const Vector3f &gyro = ins.get_gyro(); const Vector3f &mag = compass.get_field(); mavlink_msg_raw_imu_send( chan, micros(), accel.x * 1000.0 / GRAVITY_MSS, accel.y * 1000.0 / GRAVITY_MSS, accel.z * 1000.0 / GRAVITY_MSS, gyro.x * 1000.0, gyro.y * 1000.0, gyro.z * 1000.0, mag.x, mag.y, mag.z); if (ins.get_gyro_count() <= 1 && ins.get_accel_count() <= 1 && compass.get_count() <= 1) { return; } const Vector3f &accel2 = ins.get_accel(1); const Vector3f &gyro2 = ins.get_gyro(1); const Vector3f &mag2 = compass.get_field(1); mavlink_msg_scaled_imu2_send( chan, millis(), accel2.x * 1000.0f / GRAVITY_MSS, accel2.y * 1000.0f / GRAVITY_MSS, accel2.z * 1000.0f / GRAVITY_MSS, gyro2.x * 1000.0f, gyro2.y * 1000.0f, gyro2.z * 1000.0f, mag2.x, mag2.y, mag2.z); } static void NOINLINE send_raw_imu2(mavlink_channel_t chan) { float pressure = barometer.get_pressure(); mavlink_msg_scaled_pressure_send( chan, millis(), pressure*0.01f, // hectopascal (pressure - barometer.get_ground_pressure())*0.01f, // hectopascal barometer.get_temperature()*100); // 0.01 degrees C } static void NOINLINE send_raw_imu3(mavlink_channel_t chan) { // run this message at a much lower rate - otherwise it // pointlessly wastes quite a lot of bandwidth static uint8_t counter; if (counter++ < 10) { return; } counter = 0; Vector3f mag_offsets = compass.get_offsets(); Vector3f accel_offsets = ins.get_accel_offsets(); Vector3f gyro_offsets = ins.get_gyro_offsets(); mavlink_msg_sensor_offsets_send(chan, mag_offsets.x, mag_offsets.y, mag_offsets.z, compass.get_declination(), barometer.get_pressure(), barometer.get_temperature()*100, gyro_offsets.x, gyro_offsets.y, gyro_offsets.z, accel_offsets.x, accel_offsets.y, accel_offsets.z); } static void NOINLINE send_ahrs(mavlink_channel_t chan) { const Vector3f &omega_I = ahrs.get_gyro_drift(); mavlink_msg_ahrs_send( chan, omega_I.x, omega_I.y, omega_I.z, 0, 0, ahrs.get_error_rp(), ahrs.get_error_yaw()); } #if HIL_MODE != HIL_MODE_DISABLED /* keep last HIL_STATE message to allow sending SIM_STATE */ static mavlink_hil_state_t last_hil_state; #endif // report simulator state static void NOINLINE send_simstate(mavlink_channel_t chan) { #if CONFIG_HAL_BOARD == HAL_BOARD_AVR_SITL sitl.simstate_send(chan); #elif HIL_MODE != HIL_MODE_DISABLED mavlink_msg_simstate_send(chan, last_hil_state.roll, last_hil_state.pitch, last_hil_state.yaw, last_hil_state.xacc*0.001*GRAVITY_MSS, last_hil_state.yacc*0.001*GRAVITY_MSS, last_hil_state.zacc*0.001*GRAVITY_MSS, last_hil_state.rollspeed, last_hil_state.pitchspeed, last_hil_state.yawspeed, last_hil_state.lat, last_hil_state.lon); #endif } static void NOINLINE send_hwstatus(mavlink_channel_t chan) { mavlink_msg_hwstatus_send( chan, hal.analogin->board_voltage()*1000, hal.i2c->lockup_count()); } static void NOINLINE send_wind(mavlink_channel_t chan) { Vector3f wind = ahrs.wind_estimate(); mavlink_msg_wind_send( chan, degrees(atan2f(-wind.y, -wind.x)), // use negative, to give // direction wind is coming from wind.length(), wind.z); } static void NOINLINE send_rangefinder(mavlink_channel_t chan) { if (!sonar.enabled()) { // no sonar to report return; } mavlink_msg_rangefinder_send( chan, sonar.distance_cm() * 0.01f, sonar.voltage()); } static void NOINLINE send_current_waypoint(mavlink_channel_t chan) { uint16_t current_cmd_index; if (mission.state() == AP_Mission::MISSION_RUNNING) { current_cmd_index = mission.get_current_nav_cmd().index; }else{ current_cmd_index = AP_MISSION_CMD_INDEX_NONE; } mavlink_msg_mission_current_send(chan, current_cmd_index); } static void NOINLINE send_statustext(mavlink_channel_t chan) { mavlink_statustext_t *s = &gcs[chan-MAVLINK_COMM_0].pending_status; mavlink_msg_statustext_send( chan, s->severity, s->text); } // are we still delaying telemetry to try to avoid Xbee bricking? static bool telemetry_delayed(mavlink_channel_t chan) { uint32_t tnow = millis() >> 10; if (tnow > (uint32_t)g.telem_delay) { return false; } if (chan == MAVLINK_COMM_0 && hal.gpio->usb_connected()) { // this is USB telemetry, so won't be an Xbee return false; } // we're either on the 2nd UART, or no USB cable is connected // we need to delay telemetry by the TELEM_DELAY time return true; } // try to send a message, return false if it won't fit in the serial tx buffer bool GCS_MAVLINK::try_send_message(enum ap_message id) { int16_t payload_space = comm_get_txspace(chan) - MAVLINK_NUM_NON_PAYLOAD_BYTES; if (telemetry_delayed(chan)) { return false; } // if we don't have at least 1ms remaining before the main loop // wants to fire then don't send a mavlink message. We want to // prioritise the main flight control loop over communications if (!in_mavlink_delay && scheduler.time_available_usec() < 1200) { gcs_out_of_time = true; return false; } switch (id) { case MSG_HEARTBEAT: CHECK_PAYLOAD_SIZE(HEARTBEAT); gcs[chan-MAVLINK_COMM_0].last_heartbeat_time = hal.scheduler->millis(); send_heartbeat(chan); return true; case MSG_EXTENDED_STATUS1: CHECK_PAYLOAD_SIZE(SYS_STATUS); send_extended_status1(chan); CHECK_PAYLOAD_SIZE(POWER_STATUS); gcs[chan-MAVLINK_COMM_0].send_power_status(); break; case MSG_EXTENDED_STATUS2: CHECK_PAYLOAD_SIZE(MEMINFO); gcs[chan-MAVLINK_COMM_0].send_meminfo(); break; case MSG_ATTITUDE: CHECK_PAYLOAD_SIZE(ATTITUDE); send_attitude(chan); break; case MSG_LOCATION: CHECK_PAYLOAD_SIZE(GLOBAL_POSITION_INT); send_location(chan); break; case MSG_NAV_CONTROLLER_OUTPUT: if (control_mode != MANUAL) { CHECK_PAYLOAD_SIZE(NAV_CONTROLLER_OUTPUT); send_nav_controller_output(chan); } break; case MSG_GPS_RAW: CHECK_PAYLOAD_SIZE(GPS_RAW_INT); send_gps_raw(chan); break; case MSG_SYSTEM_TIME: CHECK_PAYLOAD_SIZE(SYSTEM_TIME); send_system_time(chan); break; case MSG_SERVO_OUT: #if HIL_MODE != HIL_MODE_DISABLED CHECK_PAYLOAD_SIZE(RC_CHANNELS_SCALED); send_servo_out(chan); #endif break; case MSG_RADIO_IN: CHECK_PAYLOAD_SIZE(RC_CHANNELS_RAW); send_radio_in(chan); break; case MSG_RADIO_OUT: CHECK_PAYLOAD_SIZE(SERVO_OUTPUT_RAW); send_radio_out(chan); break; case MSG_VFR_HUD: CHECK_PAYLOAD_SIZE(VFR_HUD); send_vfr_hud(chan); break; case MSG_RAW_IMU1: CHECK_PAYLOAD_SIZE(RAW_IMU); send_raw_imu1(chan); break; case MSG_RAW_IMU2: CHECK_PAYLOAD_SIZE(SCALED_PRESSURE); send_raw_imu2(chan); break; case MSG_RAW_IMU3: CHECK_PAYLOAD_SIZE(SENSOR_OFFSETS); send_raw_imu3(chan); break; case MSG_CURRENT_WAYPOINT: CHECK_PAYLOAD_SIZE(MISSION_CURRENT); send_current_waypoint(chan); break; case MSG_NEXT_PARAM: CHECK_PAYLOAD_SIZE(PARAM_VALUE); gcs[chan-MAVLINK_COMM_0].queued_param_send(); break; case MSG_NEXT_WAYPOINT: CHECK_PAYLOAD_SIZE(MISSION_REQUEST); gcs[chan-MAVLINK_COMM_0].queued_waypoint_send(); break; case MSG_STATUSTEXT: CHECK_PAYLOAD_SIZE(STATUSTEXT); send_statustext(chan); break; #if GEOFENCE_ENABLED == ENABLED case MSG_FENCE_STATUS: CHECK_PAYLOAD_SIZE(FENCE_STATUS); send_fence_status(chan); break; #endif case MSG_AHRS: CHECK_PAYLOAD_SIZE(AHRS); send_ahrs(chan); break; case MSG_SIMSTATE: CHECK_PAYLOAD_SIZE(SIMSTATE); send_simstate(chan); CHECK_PAYLOAD_SIZE(AHRS2); gcs[chan-MAVLINK_COMM_0].send_ahrs2(ahrs); break; case MSG_HWSTATUS: CHECK_PAYLOAD_SIZE(HWSTATUS); send_hwstatus(chan); break; case MSG_RANGEFINDER: CHECK_PAYLOAD_SIZE(RANGEFINDER); send_rangefinder(chan); break; case MSG_WIND: CHECK_PAYLOAD_SIZE(WIND); send_wind(chan); break; case MSG_RETRY_DEFERRED: break; // just here to prevent a warning case MSG_LIMITS_STATUS: // unused break; } return true; } /* default stream rates to 1Hz */ const AP_Param::GroupInfo GCS_MAVLINK::var_info[] PROGMEM = { // @Param: RAW_SENS // @DisplayName: Raw sensor stream rate // @Description: Raw sensor stream rate to ground station // @Units: Hz // @Range: 0 10 // @Increment: 1 // @User: Advanced AP_GROUPINFO("RAW_SENS", 0, GCS_MAVLINK, streamRates[0], 1), // @Param: EXT_STAT // @DisplayName: Extended status stream rate to ground station // @Description: Extended status stream rate to ground station // @Units: Hz // @Range: 0 10 // @Increment: 1 // @User: Advanced AP_GROUPINFO("EXT_STAT", 1, GCS_MAVLINK, streamRates[1], 1), // @Param: RC_CHAN // @DisplayName: RC Channel stream rate to ground station // @Description: RC Channel stream rate to ground station // @Units: Hz // @Range: 0 10 // @Increment: 1 // @User: Advanced AP_GROUPINFO("RC_CHAN", 2, GCS_MAVLINK, streamRates[2], 1), // @Param: RAW_CTRL // @DisplayName: Raw Control stream rate to ground station // @Description: Raw Control stream rate to ground station // @Units: Hz // @Range: 0 10 // @Increment: 1 // @User: Advanced AP_GROUPINFO("RAW_CTRL", 3, GCS_MAVLINK, streamRates[3], 1), // @Param: POSITION // @DisplayName: Position stream rate to ground station // @Description: Position stream rate to ground station // @Units: Hz // @Range: 0 10 // @Increment: 1 // @User: Advanced AP_GROUPINFO("POSITION", 4, GCS_MAVLINK, streamRates[4], 1), // @Param: EXTRA1 // @DisplayName: Extra data type 1 stream rate to ground station // @Description: Extra data type 1 stream rate to ground station // @Units: Hz // @Range: 0 10 // @Increment: 1 // @User: Advanced AP_GROUPINFO("EXTRA1", 5, GCS_MAVLINK, streamRates[5], 1), // @Param: EXTRA2 // @DisplayName: Extra data type 2 stream rate to ground station // @Description: Extra data type 2 stream rate to ground station // @Units: Hz // @Range: 0 10 // @Increment: 1 // @User: Advanced AP_GROUPINFO("EXTRA2", 6, GCS_MAVLINK, streamRates[6], 1), // @Param: EXTRA3 // @DisplayName: Extra data type 3 stream rate to ground station // @Description: Extra data type 3 stream rate to ground station // @Units: Hz // @Range: 0 10 // @Increment: 1 // @User: Advanced AP_GROUPINFO("EXTRA3", 7, GCS_MAVLINK, streamRates[7], 1), // @Param: PARAMS // @DisplayName: Parameter stream rate to ground station // @Description: Parameter stream rate to ground station // @Units: Hz // @Range: 0 10 // @Increment: 1 // @User: Advanced AP_GROUPINFO("PARAMS", 8, GCS_MAVLINK, streamRates[8], 10), AP_GROUPEND }; void GCS_MAVLINK::update(void) { // receive new packets mavlink_message_t msg; mavlink_status_t status; status.packet_rx_drop_count = 0; // process received bytes uint16_t nbytes = comm_get_available(chan); for (uint16_t i=0; i 2000U + (stream_slowdown*20)) { waypoint_timelast_request = tnow; send_message(MSG_NEXT_WAYPOINT); } // stop waypoint receiving if timeout if (waypoint_receiving && (millis() - waypoint_timelast_receive) > waypoint_receive_timeout) { waypoint_receiving = false; } } // see if we should send a stream now. Called at 50Hz bool GCS_MAVLINK::stream_trigger(enum streams stream_num) { if (stream_num >= NUM_STREAMS) { return false; } float rate = (uint8_t)streamRates[stream_num].get(); // send at a much lower rate while handling waypoints and // parameter sends if ((stream_num != STREAM_PARAMS) && (waypoint_receiving || _queued_parameter != NULL)) { rate *= 0.25; } if (rate <= 0) { return false; } if (stream_ticks[stream_num] == 0) { // we're triggering now, setup the next trigger point if (rate > 50) { rate = 50; } stream_ticks[stream_num] = (50 / rate) + stream_slowdown; return true; } // count down at 50Hz stream_ticks[stream_num]--; return false; } void GCS_MAVLINK::data_stream_send(void) { gcs_out_of_time = false; if (!in_mavlink_delay) { handle_log_send(DataFlash); } if (_queued_parameter != NULL) { if (streamRates[STREAM_PARAMS].get() <= 0) { streamRates[STREAM_PARAMS].set(10); } if (stream_trigger(STREAM_PARAMS)) { send_message(MSG_NEXT_PARAM); } } if (gcs_out_of_time) return; if (in_mavlink_delay) { #if HIL_MODE != HIL_MODE_DISABLED // in HIL we need to keep sending servo values to ensure // the simulator doesn't pause, otherwise our sensor // calibration could stall if (stream_trigger(STREAM_RAW_CONTROLLER)) { send_message(MSG_SERVO_OUT); } if (stream_trigger(STREAM_RC_CHANNELS)) { send_message(MSG_RADIO_OUT); } #endif // don't send any other stream types while in the delay callback return; } if (gcs_out_of_time) return; if (stream_trigger(STREAM_RAW_SENSORS)) { send_message(MSG_RAW_IMU1); send_message(MSG_RAW_IMU2); send_message(MSG_RAW_IMU3); } if (gcs_out_of_time) return; if (stream_trigger(STREAM_EXTENDED_STATUS)) { send_message(MSG_EXTENDED_STATUS1); send_message(MSG_EXTENDED_STATUS2); send_message(MSG_CURRENT_WAYPOINT); send_message(MSG_GPS_RAW); send_message(MSG_NAV_CONTROLLER_OUTPUT); send_message(MSG_FENCE_STATUS); } if (gcs_out_of_time) return; if (stream_trigger(STREAM_POSITION)) { // sent with GPS read send_message(MSG_LOCATION); } if (gcs_out_of_time) return; if (stream_trigger(STREAM_RAW_CONTROLLER)) { send_message(MSG_SERVO_OUT); } if (gcs_out_of_time) return; if (stream_trigger(STREAM_RC_CHANNELS)) { send_message(MSG_RADIO_OUT); send_message(MSG_RADIO_IN); } if (gcs_out_of_time) return; if (stream_trigger(STREAM_EXTRA1)) { send_message(MSG_ATTITUDE); send_message(MSG_SIMSTATE); } if (gcs_out_of_time) return; if (stream_trigger(STREAM_EXTRA2)) { send_message(MSG_VFR_HUD); } if (gcs_out_of_time) return; if (stream_trigger(STREAM_EXTRA3)) { send_message(MSG_AHRS); send_message(MSG_HWSTATUS); send_message(MSG_WIND); send_message(MSG_RANGEFINDER); send_message(MSG_SYSTEM_TIME); } } /* handle a request to switch to guided mode. This happens via a callback from handle_mission_item() */ void GCS_MAVLINK::handle_guided_request(AP_Mission::Mission_Command &cmd) { guided_WP_loc = cmd.content.location; // add home alt if needed if (guided_WP_loc.flags.relative_alt) { guided_WP_loc.alt += home.alt; } set_mode(GUIDED); // make any new wp uploaded instant (in case we are already in Guided mode) set_guided_WP(); } /* handle a request to change current WP altitude. This happens via a callback from handle_mission_item() */ void GCS_MAVLINK::handle_change_alt_request(AP_Mission::Mission_Command &cmd) { if (cmd.content.location.flags.relative_alt) { cmd.content.location.alt += home.alt; } next_WP_loc.alt = cmd.content.location.alt; } void GCS_MAVLINK::handleMessage(mavlink_message_t* msg) { switch (msg->msgid) { case MAVLINK_MSG_ID_REQUEST_DATA_STREAM: { handle_request_data_stream(msg, true); break; } case MAVLINK_MSG_ID_COMMAND_LONG: { // decode mavlink_command_long_t packet; mavlink_msg_command_long_decode(msg, &packet); if (mavlink_check_target(packet.target_system, packet.target_component)) break; uint8_t result = MAV_RESULT_UNSUPPORTED; // do command send_text_P(SEVERITY_LOW,PSTR("command received: ")); switch(packet.command) { case MAV_CMD_NAV_LOITER_UNLIM: set_mode(LOITER); result = MAV_RESULT_ACCEPTED; break; case MAV_CMD_NAV_RETURN_TO_LAUNCH: set_mode(RTL); result = MAV_RESULT_ACCEPTED; break; case MAV_CMD_MISSION_START: set_mode(AUTO); result = MAV_RESULT_ACCEPTED; break; case MAV_CMD_PREFLIGHT_CALIBRATION: if (packet.param1 == 1 || packet.param2 == 1) { startup_INS_ground(true); } else if (packet.param3 == 1) { init_barometer(); if (airspeed.enabled()) { zero_airspeed(); } } if (packet.param4 == 1) { trim_radio(); } #if !defined( __AVR_ATmega1280__ ) if (packet.param5 == 1) { float trim_roll, trim_pitch; AP_InertialSensor_UserInteract_MAVLink interact(chan); if(ins.calibrate_accel(&interact, trim_roll, trim_pitch)) { // reset ahrs's trim to suggested values from calibration routine ahrs.set_trim(Vector3f(trim_roll, trim_pitch, 0)); } } #endif result = MAV_RESULT_ACCEPTED; break; case MAV_CMD_COMPONENT_ARM_DISARM: if (packet.param1 == 1.0f) { // run pre_arm_checks and arm_checks and display failures if (arming.arm(AP_Arming::MAVLINK)) { //only log if arming was successful channel_throttle->enable_out(); Log_Arm_Disarm(); result = MAV_RESULT_ACCEPTED; } else { result = MAV_RESULT_FAILED; } } else if (packet.param1 == 0.0f) { if (arming.disarm()) { if (arming.arming_required() == AP_Arming::YES_ZERO_PWM) { channel_throttle->disable_out(); } // reset the mission on disarm mission.stop(); //only log if disarming was successful Log_Arm_Disarm(); result = MAV_RESULT_ACCEPTED; } else { result = MAV_RESULT_FAILED; } } else { result = MAV_RESULT_UNSUPPORTED; } break; case MAV_CMD_DO_SET_MODE: switch ((uint16_t)packet.param1) { case MAV_MODE_MANUAL_ARMED: case MAV_MODE_MANUAL_DISARMED: set_mode(MANUAL); result = MAV_RESULT_ACCEPTED; break; case MAV_MODE_AUTO_ARMED: case MAV_MODE_AUTO_DISARMED: set_mode(AUTO); result = MAV_RESULT_ACCEPTED; break; case MAV_MODE_STABILIZE_DISARMED: case MAV_MODE_STABILIZE_ARMED: set_mode(FLY_BY_WIRE_A); result = MAV_RESULT_ACCEPTED; break; default: result = MAV_RESULT_UNSUPPORTED; } break; case MAV_CMD_DO_SET_SERVO: if (ServoRelayEvents.do_set_servo(packet.param1, packet.param2)) { result = MAV_RESULT_ACCEPTED; } break; case MAV_CMD_DO_REPEAT_SERVO: if (ServoRelayEvents.do_repeat_servo(packet.param1, packet.param2, packet.param3, packet.param4*1000)) { result = MAV_RESULT_ACCEPTED; } break; case MAV_CMD_DO_SET_RELAY: if (ServoRelayEvents.do_set_relay(packet.param1, packet.param2)) { result = MAV_RESULT_ACCEPTED; } break; case MAV_CMD_DO_REPEAT_RELAY: if (ServoRelayEvents.do_repeat_relay(packet.param1, packet.param2, packet.param3*1000)) { result = MAV_RESULT_ACCEPTED; } break; case MAV_CMD_PREFLIGHT_REBOOT_SHUTDOWN: if (packet.param1 == 1 || packet.param1 == 3) { // when packet.param1 == 3 we reboot to hold in bootloader hal.scheduler->reboot(packet.param1 == 3); result = MAV_RESULT_ACCEPTED; } break; case MAV_CMD_DO_FENCE_ENABLE: result = MAV_RESULT_ACCEPTED; if (!geofence_present()) { result = MAV_RESULT_FAILED; } switch((uint16_t)packet.param1) { case 0: if (! geofence_set_enabled(false, GCS_TOGGLED)) { result = MAV_RESULT_FAILED; } break; case 1: if (! geofence_set_enabled(true, GCS_TOGGLED)) { result = MAV_RESULT_FAILED; } break; default: result = MAV_RESULT_FAILED; break; } break; default: break; } mavlink_msg_command_ack_send_buf( msg, chan, packet.command, result); break; } case MAVLINK_MSG_ID_SET_MODE: { // decode mavlink_set_mode_t packet; mavlink_msg_set_mode_decode(msg, &packet); if (!(packet.base_mode & MAV_MODE_FLAG_CUSTOM_MODE_ENABLED)) { // we ignore base_mode as there is no sane way to map // from that bitmap to a APM flight mode. We rely on // custom_mode instead. break; } switch (packet.custom_mode) { case MANUAL: case CIRCLE: case STABILIZE: case TRAINING: case ACRO: case FLY_BY_WIRE_A: case FLY_BY_WIRE_B: case CRUISE: case AUTO: case RTL: case LOITER: set_mode((enum FlightMode)packet.custom_mode); break; } break; } // GCS request the full list of commands, we return just the number and leave the GCS to then request each command individually case MAVLINK_MSG_ID_MISSION_REQUEST_LIST: { handle_mission_request_list(mission, msg); break; } // XXX read a WP from EEPROM and send it to the GCS case MAVLINK_MSG_ID_MISSION_REQUEST: { handle_mission_request(mission, msg); break; } case MAVLINK_MSG_ID_MISSION_ACK: { // nothing to do break; } case MAVLINK_MSG_ID_PARAM_REQUEST_LIST: { // mark the firmware version in the tlog send_text_P(SEVERITY_LOW, PSTR(FIRMWARE_STRING)); #if defined(PX4_GIT_VERSION) && defined(NUTTX_GIT_VERSION) send_text_P(SEVERITY_LOW, PSTR("PX4: " PX4_GIT_VERSION " NuttX: " NUTTX_GIT_VERSION)); #endif handle_param_request_list(msg); break; } case MAVLINK_MSG_ID_PARAM_REQUEST_READ: { handle_param_request_read(msg); break; } case MAVLINK_MSG_ID_MISSION_CLEAR_ALL: { handle_mission_clear_all(mission, msg); break; } case MAVLINK_MSG_ID_MISSION_SET_CURRENT: { handle_mission_set_current(mission, msg); if (control_mode == AUTO && mission.state() == AP_Mission::MISSION_STOPPED) { mission.resume(); } break; } // GCS provides the full number of commands it wishes to upload // individual commands will then be sent from the GCS using the MAVLINK_MSG_ID_MISSION_ITEM message case MAVLINK_MSG_ID_MISSION_COUNT: { handle_mission_count(mission, msg); break; } case MAVLINK_MSG_ID_MISSION_WRITE_PARTIAL_LIST: { handle_mission_write_partial_list(mission, msg); break; } #ifdef MAVLINK_MSG_ID_SET_MAG_OFFSETS case MAVLINK_MSG_ID_SET_MAG_OFFSETS: { mavlink_set_mag_offsets_t packet; mavlink_msg_set_mag_offsets_decode(msg, &packet); if (mavlink_check_target(packet.target_system,packet.target_component)) break; compass.set_offsets(Vector3f(packet.mag_ofs_x, packet.mag_ofs_y, packet.mag_ofs_z)); break; } #endif // GCS has sent us a command from GCS, store to EEPROM case MAVLINK_MSG_ID_MISSION_ITEM: { handle_mission_item(msg, mission); break; } #if GEOFENCE_ENABLED == ENABLED // receive a fence point from GCS and store in EEPROM case MAVLINK_MSG_ID_FENCE_POINT: { mavlink_fence_point_t packet; mavlink_msg_fence_point_decode(msg, &packet); if (mavlink_check_target(packet.target_system, packet.target_component)) break; if (g.fence_action != FENCE_ACTION_NONE) { send_text_P(SEVERITY_LOW,PSTR("fencing must be disabled")); } else if (packet.count != g.fence_total) { send_text_P(SEVERITY_LOW,PSTR("bad fence point")); } else { Vector2l point; point.x = packet.lat*1.0e7; point.y = packet.lng*1.0e7; set_fence_point_with_index(point, packet.idx); } break; } // send a fence point to GCS case MAVLINK_MSG_ID_FENCE_FETCH_POINT: { mavlink_fence_fetch_point_t packet; mavlink_msg_fence_fetch_point_decode(msg, &packet); if (mavlink_check_target(packet.target_system, packet.target_component)) break; if (packet.idx >= g.fence_total) { send_text_P(SEVERITY_LOW,PSTR("bad fence point")); } else { Vector2l point = get_fence_point_with_index(packet.idx); mavlink_msg_fence_point_send_buf(msg, chan, msg->sysid, msg->compid, packet.idx, g.fence_total, point.x*1.0e-7, point.y*1.0e-7); } break; } #endif // GEOFENCE_ENABLED // receive a rally point from GCS and store in EEPROM case MAVLINK_MSG_ID_RALLY_POINT: { mavlink_rally_point_t packet; mavlink_msg_rally_point_decode(msg, &packet); if (mavlink_check_target(packet.target_system, packet.target_component)) break; if (packet.idx >= g.rally_total || packet.idx >= MAX_RALLYPOINTS) { send_text_P(SEVERITY_LOW,PSTR("bad rally point message ID")); break; } if (packet.count != g.rally_total) { send_text_P(SEVERITY_LOW,PSTR("bad rally point message count")); break; } RallyLocation rally_point; rally_point.lat = packet.lat; rally_point.lng = packet.lng; rally_point.alt = packet.alt; rally_point.break_alt = packet.break_alt; rally_point.land_dir = packet.land_dir; rally_point.flags = packet.flags; set_rally_point_with_index(packet.idx, rally_point); break; } //send a rally point to the GCS case MAVLINK_MSG_ID_RALLY_FETCH_POINT: { mavlink_rally_fetch_point_t packet; mavlink_msg_rally_fetch_point_decode(msg, &packet); if (mavlink_check_target(packet.target_system, packet.target_component)) break; if (packet.idx > g.rally_total) { send_text_P(SEVERITY_LOW, PSTR("bad rally point index")); break; } RallyLocation rally_point; if (!get_rally_point_with_index(packet.idx, rally_point)) { send_text_P(SEVERITY_LOW, PSTR("failed to set rally point")); break; } mavlink_msg_rally_point_send_buf(msg, chan, msg->sysid, msg->compid, packet.idx, g.rally_total, rally_point.lat, rally_point.lng, rally_point.alt, rally_point.break_alt, rally_point.land_dir, rally_point.flags); break; } case MAVLINK_MSG_ID_PARAM_SET: { handle_param_set(msg, &DataFlash); break; } case MAVLINK_MSG_ID_RC_CHANNELS_OVERRIDE: { // allow override of RC channel values for HIL // or for complete GCS control of switch position // and RC PWM values. if(msg->sysid != g.sysid_my_gcs) break; // Only accept control from our gcs mavlink_rc_channels_override_t packet; int16_t v[8]; mavlink_msg_rc_channels_override_decode(msg, &packet); if (mavlink_check_target(packet.target_system,packet.target_component)) break; v[0] = packet.chan1_raw; v[1] = packet.chan2_raw; v[2] = packet.chan3_raw; v[3] = packet.chan4_raw; v[4] = packet.chan5_raw; v[5] = packet.chan6_raw; v[6] = packet.chan7_raw; v[7] = packet.chan8_raw; hal.rcin->set_overrides(v, 8); // a RC override message is consiered to be a 'heartbeat' from // the ground station for failsafe purposes failsafe.last_heartbeat_ms = millis(); break; } case MAVLINK_MSG_ID_HEARTBEAT: { // We keep track of the last time we received a heartbeat from // our GCS for failsafe purposes if (msg->sysid != g.sysid_my_gcs) break; failsafe.last_heartbeat_ms = millis(); break; } #if HIL_MODE != HIL_MODE_DISABLED case MAVLINK_MSG_ID_HIL_STATE: { mavlink_hil_state_t packet; mavlink_msg_hil_state_decode(msg, &packet); last_hil_state = packet; // set gps hil sensor Location loc; loc.lat = packet.lat; loc.lng = packet.lon; loc.alt = packet.alt/10; Vector3f vel(packet.vx, packet.vy, packet.vz); vel *= 0.01f; gps.setHIL(0, AP_GPS::GPS_OK_FIX_3D, packet.time_usec/1000, loc, vel, 10, 0, true); // rad/sec Vector3f gyros; gyros.x = packet.rollspeed; gyros.y = packet.pitchspeed; gyros.z = packet.yawspeed; // m/s/s Vector3f accels; accels.x = packet.xacc * (GRAVITY_MSS/1000.0); accels.y = packet.yacc * (GRAVITY_MSS/1000.0); accels.z = packet.zacc * (GRAVITY_MSS/1000.0); ins.set_gyro(0, gyros); ins.set_accel(0, accels); barometer.setHIL(packet.alt*0.001f); compass.setHIL(packet.roll, packet.pitch, packet.yaw); airspeed.disable(); // cope with DCM getting badly off due to HIL lag if (g.hil_err_limit > 0 && (fabsf(packet.roll - ahrs.roll) > ToRad(g.hil_err_limit) || fabsf(packet.pitch - ahrs.pitch) > ToRad(g.hil_err_limit) || wrap_PI(fabsf(packet.yaw - ahrs.yaw)) > ToRad(g.hil_err_limit))) { ahrs.reset_attitude(packet.roll, packet.pitch, packet.yaw); } break; } #endif // HIL_MODE #if CAMERA == ENABLED case MAVLINK_MSG_ID_DIGICAM_CONFIGURE: { camera.configure_msg(msg); break; } case MAVLINK_MSG_ID_DIGICAM_CONTROL: { camera.control_msg(msg); break; } #endif // CAMERA == ENABLED #if MOUNT == ENABLED case MAVLINK_MSG_ID_MOUNT_CONFIGURE: { camera_mount.configure_msg(msg); break; } case MAVLINK_MSG_ID_MOUNT_CONTROL: { camera_mount.control_msg(msg); break; } case MAVLINK_MSG_ID_MOUNT_STATUS: { camera_mount.status_msg(msg); break; } #endif // MOUNT == ENABLED case MAVLINK_MSG_ID_RADIO: case MAVLINK_MSG_ID_RADIO_STATUS: { handle_radio_status(msg, DataFlash, should_log(MASK_LOG_PM)); break; } case MAVLINK_MSG_ID_LOG_REQUEST_DATA: case MAVLINK_MSG_ID_LOG_ERASE: in_log_download = true; // fallthru case MAVLINK_MSG_ID_LOG_REQUEST_LIST: if (!in_mavlink_delay) { handle_log_message(msg, DataFlash); } break; case MAVLINK_MSG_ID_LOG_REQUEST_END: in_log_download = false; if (!in_mavlink_delay) { handle_log_message(msg, DataFlash); } break; #if HAL_CPU_CLASS > HAL_CPU_CLASS_16 case MAVLINK_MSG_ID_SERIAL_CONTROL: handle_serial_control(msg, gps); break; #endif default: // forward unknown messages to the other link if there is one for (uint8_t i=0; i ((uint16_t)msg->len) + MAVLINK_NUM_NON_PAYLOAD_BYTES) { _mavlink_resend_uart(out_chan, msg); } } } break; } // end switch } // end handle mavlink /* * a delay() callback that processes MAVLink packets. We set this as the * callback in long running library initialisation routines to allow * MAVLink to process packets while waiting for the initialisation to * complete */ static void mavlink_delay_cb() { static uint32_t last_1hz, last_50hz, last_5s; if (!gcs[0].initialised || in_mavlink_delay) return; in_mavlink_delay = true; uint32_t tnow = millis(); if (tnow - last_1hz > 1000) { last_1hz = tnow; gcs_send_message(MSG_HEARTBEAT); gcs_send_message(MSG_EXTENDED_STATUS1); } if (tnow - last_50hz > 20) { last_50hz = tnow; gcs_update(); gcs_data_stream_send(); notify.update(); } if (tnow - last_5s > 5000) { last_5s = tnow; gcs_send_text_P(SEVERITY_LOW, PSTR("Initialising APM...")); } check_usb_mux(); in_mavlink_delay = false; } /* * send a message on both GCS links */ static void gcs_send_message(enum ap_message id) { for (uint8_t i=0; ivsnprintf_P((char *)gcs[0].pending_status.text, sizeof(gcs[0].pending_status.text), fmt, arg_list); va_end(arg_list); #if LOGGING_ENABLED == ENABLED DataFlash.Log_Write_Message(gcs[0].pending_status.text); #endif gcs[0].send_message(MSG_STATUSTEXT); for (uint8_t i=1; i= MAVLINK_MSG_ID_AIRSPEED_AUTOCAL_LEN) { airspeed.log_mavlink_send((mavlink_channel_t)i, vg); } } } /** retry any deferred messages */ static void gcs_retry_deferred(void) { gcs_send_message(MSG_RETRY_DEFERRED); }