// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*- #include "Mavlink_compat.h" // use this to prevent recursion during sensor init static bool in_mavlink_delay; // this costs us 51 bytes, but means that low priority // messages don't block the CPU static mavlink_statustext_t pending_status; // true when we have received at least 1 MAVLink packet static bool mavlink_active; // check if a message will fit in the payload space available #define CHECK_PAYLOAD_SIZE(id) if (payload_space < MAVLINK_MSG_ID_## id ##_LEN) return false /* !!NOTE!! the use of NOINLINE separate functions for each message type avoids a compiler bug in gcc that would cause it to use far more stack space than is needed. Without the NOINLINE we use the sum of the stack needed for each message type. Please be careful to follow the pattern below when adding any new messages */ static NOINLINE void send_heartbeat(mavlink_channel_t chan) { uint8_t base_mode = MAV_MODE_FLAG_CUSTOM_MODE_ENABLED; uint8_t system_status = MAV_STATE_ACTIVE; uint32_t custom_mode = control_mode; // work out the base_mode. This value is not very useful // for APM, but we calculate it as best we can so a generic // MAVLink enabled ground station can work out something about // what the MAV is up to. The actual bit values are highly // ambiguous for most of the APM flight modes. In practice, you // only get useful information from the custom_mode, which maps to // the APM flight mode and has a well defined meaning in the // ArduPlane documentation base_mode = MAV_MODE_FLAG_STABILIZE_ENABLED; switch (control_mode) { case AUTO: case RTL: case LOITER: case GUIDED: case CIRCLE: base_mode |= MAV_MODE_FLAG_GUIDED_ENABLED; // note that MAV_MODE_FLAG_AUTO_ENABLED does not match what // APM does in any mode, as that is defined as "system finds its own goal // positions", which APM does not currently do break; } // all modes except INITIALISING have some form of manual // override if stick mixing is enabled base_mode |= MAV_MODE_FLAG_MANUAL_INPUT_ENABLED; #if HIL_MODE != HIL_MODE_DISABLED base_mode |= MAV_MODE_FLAG_HIL_ENABLED; #endif // we are armed if we are not initialising if (motors.armed()) { base_mode |= MAV_MODE_FLAG_SAFETY_ARMED; } // indicate we have set a custom mode base_mode |= MAV_MODE_FLAG_CUSTOM_MODE_ENABLED; mavlink_msg_heartbeat_send( chan, MAV_TYPE_QUADROTOR, MAV_AUTOPILOT_ARDUPILOTMEGA, base_mode, custom_mode, system_status); } static NOINLINE void send_attitude(mavlink_channel_t chan) { mavlink_msg_attitude_send( chan, millis(), ahrs.roll, ahrs.pitch, ahrs.yaw, omega.x, omega.y, omega.z); } #if AP_LIMITS == ENABLED static NOINLINE void send_limits_status(mavlink_channel_t chan) { limits_send_mavlink_status(chan); } #endif static NOINLINE void send_extended_status1(mavlink_channel_t chan, uint16_t packet_drops) { uint32_t control_sensors_present = 0; uint32_t control_sensors_enabled; uint32_t control_sensors_health; // first what sensors/controllers we have control_sensors_present |= (1<<0); // 3D gyro present control_sensors_present |= (1<<1); // 3D accelerometer present if (g.compass_enabled) { control_sensors_present |= (1<<2); // compass present } control_sensors_present |= (1<<3); // absolute pressure sensor present if (g_gps != NULL && g_gps->status() == GPS::GPS_OK) { control_sensors_present |= (1<<5); // GPS present } control_sensors_present |= (1<<10); // 3D angular rate control control_sensors_present |= (1<<11); // attitude stabilisation control_sensors_present |= (1<<12); // yaw position control_sensors_present |= (1<<13); // altitude control control_sensors_present |= (1<<14); // X/Y position control control_sensors_present |= (1<<15); // motor control // now what sensors/controllers are enabled // first the sensors control_sensors_enabled = control_sensors_present & 0x1FF; // now the controllers control_sensors_enabled = control_sensors_present & 0x1FF; control_sensors_enabled |= (1<<10); // 3D angular rate control control_sensors_enabled |= (1<<11); // attitude stabilisation control_sensors_enabled |= (1<<13); // altitude control control_sensors_enabled |= (1<<15); // motor control switch (control_mode) { case AUTO: case RTL: case LOITER: case GUIDED: case CIRCLE: case POSITION: control_sensors_enabled |= (1<<12); // yaw position control_sensors_enabled |= (1<<14); // X/Y position control break; } // at the moment all sensors/controllers are assumed healthy control_sensors_health = control_sensors_present; uint16_t battery_current = -1; uint8_t battery_remaining = -1; if (current_total1 != 0 && g.pack_capacity != 0) { battery_remaining = (100.0 * (g.pack_capacity - current_total1) / g.pack_capacity); } if (current_total1 != 0) { battery_current = current_amps1 * 100; } if (g.battery_monitoring == 3) { /*setting a out-of-range value. It informs to external devices that it cannot be calculated properly just by voltage*/ battery_remaining = 150; } mavlink_msg_sys_status_send( chan, control_sensors_present, control_sensors_enabled, control_sensors_health, 0, // CPU Load not supported in AC yet battery_voltage1 * 1000, // mV battery_current, // in 10mA units battery_remaining, // in % 0, // comm drops %, 0, // comm drops in pkts, 0, 0, 0, 0); } static void NOINLINE send_meminfo(mavlink_channel_t chan) { extern unsigned __brkval; mavlink_msg_meminfo_send(chan, __brkval, memcheck_available_memory()); } static void NOINLINE send_location(mavlink_channel_t chan) { Matrix3f rot = ahrs.get_dcm_matrix(); // neglecting angle of attack for now mavlink_msg_global_position_int_send( chan, millis(), current_loc.lat, // in 1E7 degrees current_loc.lng, // in 1E7 degrees g_gps->altitude * 10, // millimeters above sea level (current_loc.alt - home.alt) * 10, // millimeters above ground g_gps->ground_speed * rot.a.x, // X speed cm/s g_gps->ground_speed * rot.b.x, // Y speed cm/s g_gps->ground_speed * rot.c.x, g_gps->ground_course); // course in 1/100 degree } static void NOINLINE send_nav_controller_output(mavlink_channel_t chan) { mavlink_msg_nav_controller_output_send( chan, nav_roll / 1.0e2, nav_pitch / 1.0e2, target_bearing / 1.0e2, target_bearing / 1.0e2, wp_distance / 1.0e2, altitude_error / 1.0e2, 0, crosstrack_error); // was 0 } static void NOINLINE send_ahrs(mavlink_channel_t chan) { Vector3f omega_I = ahrs.get_gyro_drift(); mavlink_msg_ahrs_send( chan, omega_I.x, omega_I.y, omega_I.z, 1, 0, ahrs.get_error_rp(), ahrs.get_error_yaw()); } #ifdef DESKTOP_BUILD // report simulator state static void NOINLINE send_simstate(mavlink_channel_t chan) { sitl.simstate_send(chan); } #endif #ifndef DESKTOP_BUILD static void NOINLINE send_hwstatus(mavlink_channel_t chan) { mavlink_msg_hwstatus_send( chan, board_voltage(), I2c.lockup_count()); } #endif static void NOINLINE send_gps_raw(mavlink_channel_t chan) { uint8_t fix = g_gps->status(); if (fix == GPS::GPS_OK) { fix = 3; } mavlink_msg_gps_raw_int_send( chan, g_gps->last_fix_time*(uint64_t)1000, fix, g_gps->latitude, // in 1E7 degrees g_gps->longitude, // in 1E7 degrees g_gps->altitude * 10, // in mm g_gps->hdop, 65535, g_gps->ground_speed, // cm/s g_gps->ground_course, // 1/100 degrees, g_gps->num_sats); } static void NOINLINE send_servo_out(mavlink_channel_t chan) { const uint8_t rssi = 1; // normalized values scaled to -10000 to 10000 // This is used for HIL. Do not change without discussing with HIL maintainers #if FRAME_CONFIG == HELI_FRAME mavlink_msg_rc_channels_scaled_send( chan, millis(), 0, // port 0 g.rc_1.servo_out, g.rc_2.servo_out, g.rc_3.radio_out, g.rc_4.servo_out, 0, 0, 0, 0, rssi); #else #if X_PLANE == ENABLED /* update by JLN for X-Plane HIL */ if(motors.armed() && motors.auto_armed()){ mavlink_msg_rc_channels_scaled_send( chan, millis(), 0, // port 0 g.rc_1.servo_out, g.rc_2.servo_out, 10000 * g.rc_3.norm_output(), g.rc_4.servo_out, 10000 * g.rc_1.norm_output(), 10000 * g.rc_2.norm_output(), 10000 * g.rc_3.norm_output(), 10000 * g.rc_4.norm_output(), rssi); }else{ mavlink_msg_rc_channels_scaled_send( chan, millis(), 0, // port 0 0, 0, -10000, 0, 10000 * g.rc_1.norm_output(), 10000 * g.rc_2.norm_output(), 10000 * g.rc_3.norm_output(), 10000 * g.rc_4.norm_output(), rssi); } #else mavlink_msg_rc_channels_scaled_send( chan, millis(), 0, // port 0 g.rc_1.servo_out, g.rc_2.servo_out, g.rc_3.radio_out, g.rc_4.servo_out, 10000 * g.rc_1.norm_output(), 10000 * g.rc_2.norm_output(), 10000 * g.rc_3.norm_output(), 10000 * g.rc_4.norm_output(), rssi); #endif #endif } static void NOINLINE send_radio_in(mavlink_channel_t chan) { const uint8_t rssi = 1; mavlink_msg_rc_channels_raw_send( chan, millis(), 0, // port g.rc_1.radio_in, g.rc_2.radio_in, g.rc_3.radio_in, g.rc_4.radio_in, g.rc_5.radio_in, g.rc_6.radio_in, g.rc_7.radio_in, g.rc_8.radio_in, rssi); } static void NOINLINE send_radio_out(mavlink_channel_t chan) { mavlink_msg_servo_output_raw_send( chan, micros(), 0, // port motors.motor_out[AP_MOTORS_MOT_1], motors.motor_out[AP_MOTORS_MOT_2], motors.motor_out[AP_MOTORS_MOT_3], motors.motor_out[AP_MOTORS_MOT_4], motors.motor_out[AP_MOTORS_MOT_5], motors.motor_out[AP_MOTORS_MOT_6], motors.motor_out[AP_MOTORS_MOT_7], motors.motor_out[AP_MOTORS_MOT_8]); } static void NOINLINE send_vfr_hud(mavlink_channel_t chan) { mavlink_msg_vfr_hud_send( chan, (float)g_gps->ground_speed / 100.0, (float)g_gps->ground_speed / 100.0, (ahrs.yaw_sensor / 100) % 360, g.rc_3.servo_out/10, current_loc.alt / 100.0, climb_rate / 100.0); } static void NOINLINE send_raw_imu1(mavlink_channel_t chan) { Vector3f accel = imu.get_accel(); Vector3f gyro = imu.get_gyro(); mavlink_msg_raw_imu_send( chan, micros(), accel.x * 1000.0 / gravity, accel.y * 1000.0 / gravity, accel.z * 1000.0 / gravity, gyro.x * 1000.0, gyro.y * 1000.0, gyro.z * 1000.0, compass.mag_x, compass.mag_y, compass.mag_z); } static void NOINLINE send_raw_imu2(mavlink_channel_t chan) { mavlink_msg_scaled_pressure_send( chan, millis(), (float)barometer.get_pressure()/100.0, (float)(barometer.get_pressure() - barometer.get_ground_pressure())/100.0, (int)(barometer.get_temperature()*10)); } static void NOINLINE send_raw_imu3(mavlink_channel_t chan) { Vector3f mag_offsets = compass.get_offsets(); mavlink_msg_sensor_offsets_send(chan, mag_offsets.x, mag_offsets.y, mag_offsets.z, compass.get_declination(), barometer.get_raw_pressure(), barometer.get_raw_temp(), imu.gx(), imu.gy(), imu.gz(), imu.ax(), imu.ay(), imu.az()); } static void NOINLINE send_gps_status(mavlink_channel_t chan) { mavlink_msg_gps_status_send( chan, g_gps->num_sats, NULL, NULL, NULL, NULL, NULL); } static void NOINLINE send_current_waypoint(mavlink_channel_t chan) { mavlink_msg_waypoint_current_send( chan, (uint16_t)g.command_index); } static void NOINLINE send_statustext(mavlink_channel_t chan) { mavlink_msg_statustext_send( chan, pending_status.severity, pending_status.text); } // try to send a message, return false if it won't fit in the serial tx buffer static bool mavlink_try_send_message(mavlink_channel_t chan, enum ap_message id, uint16_t packet_drops) { int payload_space = comm_get_txspace(chan) - MAVLINK_NUM_NON_PAYLOAD_BYTES; if (chan == MAVLINK_COMM_1 && millis() < MAVLINK_TELEMETRY_PORT_DELAY) { // defer any messages on the telemetry port for 1 second after // bootup, to try to prevent bricking of Xbees return false; } switch(id) { case MSG_HEARTBEAT: CHECK_PAYLOAD_SIZE(HEARTBEAT); send_heartbeat(chan); return true; case MSG_EXTENDED_STATUS1: CHECK_PAYLOAD_SIZE(SYS_STATUS); send_extended_status1(chan, packet_drops); break; case MSG_EXTENDED_STATUS2: CHECK_PAYLOAD_SIZE(MEMINFO); send_meminfo(chan); break; case MSG_ATTITUDE: CHECK_PAYLOAD_SIZE(ATTITUDE); send_attitude(chan); break; case MSG_LOCATION: CHECK_PAYLOAD_SIZE(GLOBAL_POSITION_INT); send_location(chan); break; case MSG_NAV_CONTROLLER_OUTPUT: CHECK_PAYLOAD_SIZE(NAV_CONTROLLER_OUTPUT); send_nav_controller_output(chan); break; case MSG_GPS_RAW: CHECK_PAYLOAD_SIZE(GPS_RAW_INT); send_gps_raw(chan); break; case MSG_SERVO_OUT: CHECK_PAYLOAD_SIZE(RC_CHANNELS_SCALED); send_servo_out(chan); break; case MSG_RADIO_IN: CHECK_PAYLOAD_SIZE(RC_CHANNELS_RAW); send_radio_in(chan); break; case MSG_RADIO_OUT: CHECK_PAYLOAD_SIZE(SERVO_OUTPUT_RAW); send_radio_out(chan); break; case MSG_VFR_HUD: CHECK_PAYLOAD_SIZE(VFR_HUD); send_vfr_hud(chan); break; case MSG_RAW_IMU1: CHECK_PAYLOAD_SIZE(RAW_IMU); send_raw_imu1(chan); break; case MSG_RAW_IMU2: CHECK_PAYLOAD_SIZE(SCALED_PRESSURE); send_raw_imu2(chan); break; case MSG_RAW_IMU3: CHECK_PAYLOAD_SIZE(SENSOR_OFFSETS); send_raw_imu3(chan); break; case MSG_GPS_STATUS: CHECK_PAYLOAD_SIZE(GPS_STATUS); send_gps_status(chan); break; case MSG_CURRENT_WAYPOINT: CHECK_PAYLOAD_SIZE(WAYPOINT_CURRENT); send_current_waypoint(chan); break; case MSG_NEXT_PARAM: CHECK_PAYLOAD_SIZE(PARAM_VALUE); if (chan == MAVLINK_COMM_0) { gcs0.queued_param_send(); } else if (gcs3.initialised) { gcs3.queued_param_send(); } break; case MSG_NEXT_WAYPOINT: CHECK_PAYLOAD_SIZE(WAYPOINT_REQUEST); if (chan == MAVLINK_COMM_0) { gcs0.queued_waypoint_send(); } else { gcs3.queued_waypoint_send(); } break; case MSG_STATUSTEXT: CHECK_PAYLOAD_SIZE(STATUSTEXT); send_statustext(chan); break; #if AP_LIMITS == ENABLED case MSG_LIMITS_STATUS: CHECK_PAYLOAD_SIZE(LIMITS_STATUS); send_limits_status(chan); break; #endif case MSG_AHRS: CHECK_PAYLOAD_SIZE(AHRS); send_ahrs(chan); break; case MSG_SIMSTATE: #ifdef DESKTOP_BUILD CHECK_PAYLOAD_SIZE(SIMSTATE); send_simstate(chan); #endif break; case MSG_HWSTATUS: #ifndef DESKTOP_BUILD CHECK_PAYLOAD_SIZE(HWSTATUS); send_hwstatus(chan); #endif break; case MSG_RETRY_DEFERRED: break; // just here to prevent a warning } return true; } #define MAX_DEFERRED_MESSAGES MSG_RETRY_DEFERRED static struct mavlink_queue { enum ap_message deferred_messages[MAX_DEFERRED_MESSAGES]; uint8_t next_deferred_message; uint8_t num_deferred_messages; } mavlink_queue[2]; // send a message using mavlink static void mavlink_send_message(mavlink_channel_t chan, enum ap_message id, uint16_t packet_drops) { uint8_t i, nextid; struct mavlink_queue *q = &mavlink_queue[(uint8_t)chan]; // see if we can send the deferred messages, if any while (q->num_deferred_messages != 0) { if (!mavlink_try_send_message(chan, q->deferred_messages[q->next_deferred_message], packet_drops)) { break; } q->next_deferred_message++; if (q->next_deferred_message == MAX_DEFERRED_MESSAGES) { q->next_deferred_message = 0; } q->num_deferred_messages--; } if (id == MSG_RETRY_DEFERRED) { return; } // this message id might already be deferred for (i=0, nextid = q->next_deferred_message; i < q->num_deferred_messages; i++) { if (q->deferred_messages[nextid] == id) { // its already deferred, discard return; } nextid++; if (nextid == MAX_DEFERRED_MESSAGES) { nextid = 0; } } if (q->num_deferred_messages != 0 || !mavlink_try_send_message(chan, id, packet_drops)) { // can't send it now, so defer it if (q->num_deferred_messages == MAX_DEFERRED_MESSAGES) { // the defer buffer is full, discard return; } nextid = q->next_deferred_message + q->num_deferred_messages; if (nextid >= MAX_DEFERRED_MESSAGES) { nextid -= MAX_DEFERRED_MESSAGES; } q->deferred_messages[nextid] = id; q->num_deferred_messages++; } } void mavlink_send_text(mavlink_channel_t chan, gcs_severity severity, const char *str) { if (chan == MAVLINK_COMM_1 && millis() < MAVLINK_TELEMETRY_PORT_DELAY) { // don't send status MAVLink messages for 2 seconds after // bootup, to try to prevent Xbee bricking return; } if (severity == SEVERITY_LOW) { // send via the deferred queuing system pending_status.severity = (uint8_t)severity; strncpy((char *)pending_status.text, str, sizeof(pending_status.text)); mavlink_send_message(chan, MSG_STATUSTEXT, 0); } else { // send immediately mavlink_msg_statustext_send( chan, severity, str); } } const AP_Param::GroupInfo GCS_MAVLINK::var_info[] PROGMEM = { AP_GROUPINFO("RAW_SENS", 0, GCS_MAVLINK, streamRateRawSensors), AP_GROUPINFO("EXT_STAT", 1, GCS_MAVLINK, streamRateExtendedStatus), AP_GROUPINFO("RC_CHAN", 2, GCS_MAVLINK, streamRateRCChannels), AP_GROUPINFO("RAW_CTRL", 3, GCS_MAVLINK, streamRateRawController), AP_GROUPINFO("POSITION", 4, GCS_MAVLINK, streamRatePosition), AP_GROUPINFO("EXTRA1", 5, GCS_MAVLINK, streamRateExtra1), AP_GROUPINFO("EXTRA2", 6, GCS_MAVLINK, streamRateExtra2), AP_GROUPINFO("EXTRA3", 7, GCS_MAVLINK, streamRateExtra3), AP_GROUPINFO("PARAMS", 8, GCS_MAVLINK, streamRateParams), AP_GROUPEND }; GCS_MAVLINK::GCS_MAVLINK() : packet_drops(0), waypoint_send_timeout(1000), // 1 second waypoint_receive_timeout(1000) // 1 second { } void GCS_MAVLINK::init(FastSerial * port) { GCS_Class::init(port); if (port == &Serial) { mavlink_comm_0_port = port; chan = MAVLINK_COMM_0; }else{ mavlink_comm_1_port = port; chan = MAVLINK_COMM_1; } _queued_parameter = NULL; } void GCS_MAVLINK::update(void) { // receive new packets mavlink_message_t msg; mavlink_status_t status; status.packet_rx_drop_count = 0; // process received bytes while(comm_get_available(chan)) { uint8_t c = comm_receive_ch(chan); #if CLI_ENABLED == ENABLED /* allow CLI to be started by hitting enter 3 times, if no heartbeat packets have been received */ if (mavlink_active == false) { if (c == '\n' || c == '\r') { crlf_count++; } else { crlf_count = 0; } if (crlf_count == 3) { run_cli(); } } #endif // Try to get a new message if (mavlink_parse_char(chan, c, &msg, &status)) { mavlink_active = true; handleMessage(&msg); } } // Update packet drops counter packet_drops += status.packet_rx_drop_count; if (!waypoint_receiving && !waypoint_sending) { return; } uint32_t tnow = millis(); if (waypoint_receiving && waypoint_request_i <= (unsigned)g.command_total && tnow > waypoint_timelast_request + 500 + (stream_slowdown*20)) { waypoint_timelast_request = tnow; send_message(MSG_NEXT_WAYPOINT); } // stop waypoint sending if timeout if (waypoint_sending && (tnow - waypoint_timelast_send) > waypoint_send_timeout){ waypoint_sending = false; } // stop waypoint receiving if timeout if (waypoint_receiving && (tnow - waypoint_timelast_receive) > waypoint_receive_timeout){ waypoint_receiving = false; } } // see if we should send a stream now. Called at 50Hz bool GCS_MAVLINK::stream_trigger(enum streams stream_num) { AP_Int16 *stream_rates = &streamRateRawSensors; uint8_t rate = (uint8_t)stream_rates[stream_num].get(); if (rate == 0) { return false; } if (stream_ticks[stream_num] == 0) { // we're triggering now, setup the next trigger point if (rate > 50) { rate = 50; } stream_ticks[stream_num] = (50 / rate) + stream_slowdown; return true; } // count down at 50Hz stream_ticks[stream_num]--; return false; } void GCS_MAVLINK::data_stream_send(void) { if (waypoint_receiving || waypoint_sending) { // don't interfere with mission transfer return; } if (_queued_parameter != NULL) { if (streamRateParams.get() <= 0) { streamRateParams.set(50); } if (stream_trigger(STREAM_PARAMS)) { send_message(MSG_NEXT_PARAM); } // don't send anything else at the same time as parameters return; } if (in_mavlink_delay) { // don't send any other stream types while in the delay callback return; } if (stream_trigger(STREAM_RAW_SENSORS)) { send_message(MSG_RAW_IMU1); send_message(MSG_RAW_IMU2); send_message(MSG_RAW_IMU3); //Serial.printf("mav1 %d\n", (int)streamRateRawSensors.get()); } if (stream_trigger(STREAM_EXTENDED_STATUS)) { send_message(MSG_EXTENDED_STATUS1); send_message(MSG_EXTENDED_STATUS2); send_message(MSG_CURRENT_WAYPOINT); send_message(MSG_GPS_RAW); // TODO - remove this message after location message is working send_message(MSG_NAV_CONTROLLER_OUTPUT); send_message(MSG_LIMITS_STATUS); if (last_gps_satellites != g_gps->num_sats) { // this message is mostly a huge waste of bandwidth, // except it is the only message that gives the number // of visible satellites. So only send it when that // changes. send_message(MSG_GPS_STATUS); last_gps_satellites = g_gps->num_sats; } } if (stream_trigger(STREAM_POSITION)) { // sent with GPS read //Serial.printf("mav3 %d\n", (int)streamRatePosition.get()); } if (stream_trigger(STREAM_RAW_CONTROLLER)) { send_message(MSG_SERVO_OUT); //Serial.printf("mav4 %d\n", (int)streamRateRawController.get()); } if (stream_trigger(STREAM_RC_CHANNELS)) { send_message(MSG_RADIO_OUT); send_message(MSG_RADIO_IN); //Serial.printf("mav5 %d\n", (int)streamRateRCChannels.get()); } if (stream_trigger(STREAM_EXTRA1)) { send_message(MSG_ATTITUDE); send_message(MSG_SIMSTATE); //Serial.printf("mav6 %d\n", (int)streamRateExtra1.get()); } if (stream_trigger(STREAM_EXTRA2)) { send_message(MSG_VFR_HUD); //Serial.printf("mav7 %d\n", (int)streamRateExtra2.get()); } if (stream_trigger(STREAM_EXTRA3)) { send_message(MSG_AHRS); send_message(MSG_HWSTATUS); } } void GCS_MAVLINK::send_message(enum ap_message id) { mavlink_send_message(chan,id, packet_drops); } void GCS_MAVLINK::send_text(gcs_severity severity, const char *str) { mavlink_send_text(chan,severity,str); } void GCS_MAVLINK::send_text(gcs_severity severity, const prog_char_t *str) { mavlink_statustext_t m; uint8_t i; for (i=0; imsgid) { case MAVLINK_MSG_ID_REQUEST_DATA_STREAM: //66 { // decode mavlink_request_data_stream_t packet; mavlink_msg_request_data_stream_decode(msg, &packet); if (mavlink_check_target(packet.target_system, packet.target_component)) break; int freq = 0; // packet frequency if (packet.start_stop == 0) freq = 0; // stop sending else if (packet.start_stop == 1) freq = packet.req_message_rate; // start sending else break; switch(packet.req_stream_id){ case MAV_DATA_STREAM_ALL: streamRateRawSensors = freq; streamRateExtendedStatus = freq; streamRateRCChannels = freq; streamRateRawController = freq; streamRatePosition = freq; streamRateExtra1 = freq; streamRateExtra2 = freq; //streamRateExtra3.set_and_save(freq); // We just do set and save on the last as it takes care of the whole group. streamRateExtra3 = freq; // Don't save!! break; case MAV_DATA_STREAM_RAW_SENSORS: streamRateRawSensors = freq; // We do not set and save this one so that if HIL is shut down incorrectly // we will not continue to broadcast raw sensor data at 50Hz. break; case MAV_DATA_STREAM_EXTENDED_STATUS: //streamRateExtendedStatus.set_and_save(freq); streamRateExtendedStatus = freq; break; case MAV_DATA_STREAM_RC_CHANNELS: streamRateRCChannels = freq; break; case MAV_DATA_STREAM_RAW_CONTROLLER: streamRateRawController = freq; break; //case MAV_DATA_STREAM_RAW_SENSOR_FUSION: // streamRateRawSensorFusion.set_and_save(freq); // break; case MAV_DATA_STREAM_POSITION: streamRatePosition = freq; break; case MAV_DATA_STREAM_EXTRA1: streamRateExtra1 = freq; break; case MAV_DATA_STREAM_EXTRA2: streamRateExtra2 = freq; break; case MAV_DATA_STREAM_EXTRA3: streamRateExtra3 = freq; break; default: break; } break; } case MAVLINK_MSG_ID_COMMAND_LONG: { // decode mavlink_command_long_t packet; mavlink_msg_command_long_decode(msg, &packet); if (mavlink_check_target(packet.target_system, packet.target_component)) break; uint8_t result; // do command send_text(SEVERITY_LOW,PSTR("command received: ")); switch(packet.command) { case MAV_CMD_NAV_LOITER_UNLIM: set_mode(LOITER); result = MAV_RESULT_ACCEPTED; break; case MAV_CMD_NAV_RETURN_TO_LAUNCH: set_mode(RTL); result = MAV_RESULT_ACCEPTED; break; case MAV_CMD_NAV_LAND: set_mode(LAND); result = MAV_RESULT_ACCEPTED; break; case MAV_CMD_MISSION_START: set_mode(AUTO); result = MAV_RESULT_ACCEPTED; break; case MAV_CMD_PREFLIGHT_CALIBRATION: if (packet.param1 == 1 || packet.param2 == 1 || packet.param3 == 1) { imu.init_accel(mavlink_delay, flash_leds); } if (packet.param4 == 1) { trim_radio(); } result = MAV_RESULT_ACCEPTED; break; default: result = MAV_RESULT_UNSUPPORTED; break; } mavlink_msg_command_ack_send( chan, packet.command, result); break; } case MAVLINK_MSG_ID_SET_MODE: //11 { // decode mavlink_set_mode_t packet; mavlink_msg_set_mode_decode(msg, &packet); if (!(packet.base_mode & MAV_MODE_FLAG_CUSTOM_MODE_ENABLED)) { // we ignore base_mode as there is no sane way to map // from that bitmap to a APM flight mode. We rely on // custom_mode instead. break; } switch (packet.custom_mode) { case STABILIZE: case ACRO: case ALT_HOLD: case AUTO: case GUIDED: case LOITER: case RTL: case CIRCLE: case POSITION: case LAND: case OF_LOITER: set_mode(packet.custom_mode); break; } break; } /*case MAVLINK_MSG_ID_SET_NAV_MODE: { // decode mavlink_set_nav_mode_t packet; mavlink_msg_set_nav_mode_decode(msg, &packet); // To set some flight modes we must first receive a "set nav mode" message and then a "set mode" message mav_nav = packet.nav_mode; break; } */ case MAVLINK_MSG_ID_WAYPOINT_REQUEST_LIST: //43 { //send_text_P(SEVERITY_LOW,PSTR("waypoint request list")); // decode mavlink_waypoint_request_list_t packet; mavlink_msg_waypoint_request_list_decode(msg, &packet); if (mavlink_check_target(packet.target_system, packet.target_component)) break; // Start sending waypoints mavlink_msg_waypoint_count_send( chan,msg->sysid, msg->compid, g.command_total); // includes home waypoint_timelast_send = millis(); waypoint_sending = true; waypoint_receiving = false; waypoint_dest_sysid = msg->sysid; waypoint_dest_compid = msg->compid; break; } // XXX read a WP from EEPROM and send it to the GCS case MAVLINK_MSG_ID_WAYPOINT_REQUEST: // 40 { //send_text_P(SEVERITY_LOW,PSTR("waypoint request")); // Check if sending waypiont //if (!waypoint_sending) break; // 5/10/11 - We are trying out relaxing the requirement that we be in waypoint sending mode to respond to a waypoint request. DEW // decode mavlink_waypoint_request_t packet; mavlink_msg_waypoint_request_decode(msg, &packet); if (mavlink_check_target(packet.target_system, packet.target_component)) break; // send waypoint tell_command = get_cmd_with_index(packet.seq); // set frame of waypoint uint8_t frame; if (tell_command.options & MASK_OPTIONS_RELATIVE_ALT) { frame = MAV_FRAME_GLOBAL_RELATIVE_ALT; // reference frame } else { frame = MAV_FRAME_GLOBAL; // reference frame } float param1 = 0, param2 = 0 , param3 = 0, param4 = 0; // time that the mav should loiter in milliseconds uint8_t current = 0; // 1 (true), 0 (false) if (packet.seq == (uint16_t)g.command_index) current = 1; uint8_t autocontinue = 1; // 1 (true), 0 (false) float x = 0, y = 0, z = 0; if (tell_command.id < MAV_CMD_NAV_LAST) { // command needs scaling x = tell_command.lat/1.0e7; // local (x), global (latitude) y = tell_command.lng/1.0e7; // local (y), global (longitude) // ACM is processing alt inside each command. so we save and load raw values. - this is diffrent to APM z = tell_command.alt/1.0e2; // local (z), global/relative (altitude) } // Switch to map APM command fields into MAVLink command fields switch (tell_command.id) { case MAV_CMD_NAV_LOITER_TURNS: case MAV_CMD_CONDITION_CHANGE_ALT: case MAV_CMD_DO_SET_HOME: param1 = tell_command.p1; break; case MAV_CMD_NAV_ROI: param1 = tell_command.p1; // MAV_ROI (aka roi mode) is held in wp's parameter but we actually do nothing with it because we only support pointing at a specific location provided by x,y and z parameters break; case MAV_CMD_CONDITION_YAW: param3 = tell_command.p1; param1 = tell_command.alt; param2 = tell_command.lat; param4 = tell_command.lng; break; case MAV_CMD_NAV_TAKEOFF: param1 = 0; break; case MAV_CMD_NAV_LOITER_TIME: param1 = tell_command.p1; // ACM loiter time is in 1 second increments break; case MAV_CMD_CONDITION_DELAY: case MAV_CMD_CONDITION_DISTANCE: param1 = tell_command.lat; break; case MAV_CMD_DO_JUMP: param2 = tell_command.lat; param1 = tell_command.p1; break; case MAV_CMD_DO_REPEAT_SERVO: param4 = tell_command.lng; case MAV_CMD_DO_REPEAT_RELAY: case MAV_CMD_DO_CHANGE_SPEED: param3 = tell_command.lat; param2 = tell_command.alt; param1 = tell_command.p1; break; case MAV_CMD_NAV_WAYPOINT: param1 = tell_command.p1; break; case MAV_CMD_DO_SET_PARAMETER: case MAV_CMD_DO_SET_RELAY: case MAV_CMD_DO_SET_SERVO: param2 = tell_command.alt; param1 = tell_command.p1; break; } mavlink_msg_waypoint_send(chan,msg->sysid, msg->compid, packet.seq, frame, tell_command.id, current, autocontinue, param1, param2, param3, param4, x, y, z); // update last waypoint comm stamp waypoint_timelast_send = millis(); break; } case MAVLINK_MSG_ID_WAYPOINT_ACK: //47 { //send_text_P(SEVERITY_LOW,PSTR("waypoint ack")); // decode mavlink_waypoint_ack_t packet; mavlink_msg_waypoint_ack_decode(msg, &packet); if (mavlink_check_target(packet.target_system,packet.target_component)) break; // turn off waypoint send waypoint_sending = false; break; } case MAVLINK_MSG_ID_PARAM_REQUEST_LIST: // 21 { // gcs_send_text_P(SEVERITY_LOW,PSTR("param request list")); // decode mavlink_param_request_list_t packet; mavlink_msg_param_request_list_decode(msg, &packet); if (mavlink_check_target(packet.target_system,packet.target_component)) break; // Start sending parameters - next call to ::update will kick the first one out _queued_parameter = AP_Param::first(&_queued_parameter_token, &_queued_parameter_type); _queued_parameter_index = 0; _queued_parameter_count = _count_parameters(); break; } case MAVLINK_MSG_ID_WAYPOINT_CLEAR_ALL: // 45 { //send_text_P(SEVERITY_LOW,PSTR("waypoint clear all")); // decode mavlink_waypoint_clear_all_t packet; mavlink_msg_waypoint_clear_all_decode(msg, &packet); if (mavlink_check_target(packet.target_system, packet.target_component)) break; // clear all waypoints uint8_t type = 0; // ok (0), error(1) g.command_total.set_and_save(1); // send acknowledgement 3 times to makes sure it is received for (int i=0;i<3;i++) mavlink_msg_waypoint_ack_send(chan, msg->sysid, msg->compid, type); break; } case MAVLINK_MSG_ID_WAYPOINT_SET_CURRENT: // 41 { //send_text_P(SEVERITY_LOW,PSTR("waypoint set current")); // decode mavlink_waypoint_set_current_t packet; mavlink_msg_waypoint_set_current_decode(msg, &packet); if (mavlink_check_target(packet.target_system,packet.target_component)) break; // set current command change_command(packet.seq); mavlink_msg_waypoint_current_send(chan, g.command_index); break; } case MAVLINK_MSG_ID_WAYPOINT_COUNT: // 44 { //send_text_P(SEVERITY_LOW,PSTR("waypoint count")); // decode mavlink_waypoint_count_t packet; mavlink_msg_waypoint_count_decode(msg, &packet); if (mavlink_check_target(packet.target_system,packet.target_component)) break; // start waypoint receiving if (packet.count > MAX_WAYPOINTS) { packet.count = MAX_WAYPOINTS; } g.command_total.set_and_save(packet.count); waypoint_timelast_receive = millis(); waypoint_receiving = true; waypoint_sending = false; waypoint_request_i = 0; waypoint_timelast_request = 0; break; } #ifdef MAVLINK_MSG_ID_SET_MAG_OFFSETS case MAVLINK_MSG_ID_SET_MAG_OFFSETS: { mavlink_set_mag_offsets_t packet; mavlink_msg_set_mag_offsets_decode(msg, &packet); if (mavlink_check_target(packet.target_system,packet.target_component)) break; compass.set_offsets(Vector3f(packet.mag_ofs_x, packet.mag_ofs_y, packet.mag_ofs_z)); break; } #endif // XXX receive a WP from GCS and store in EEPROM case MAVLINK_MSG_ID_WAYPOINT: //39 { // decode mavlink_waypoint_t packet; mavlink_msg_waypoint_decode(msg, &packet); if (mavlink_check_target(packet.target_system,packet.target_component)) break; // defaults tell_command.id = packet.command; /* switch (packet.frame){ case MAV_FRAME_MISSION: case MAV_FRAME_GLOBAL: { tell_command.lat = 1.0e7*packet.x; // in as DD converted to * t7 tell_command.lng = 1.0e7*packet.y; // in as DD converted to * t7 tell_command.alt = packet.z*1.0e2; // in as m converted to cm tell_command.options = 0; // absolute altitude break; } case MAV_FRAME_LOCAL: // local (relative to home position) { tell_command.lat = 1.0e7*ToDeg(packet.x/ (radius_of_earth*cos(ToRad(home.lat/1.0e7)))) + home.lat; tell_command.lng = 1.0e7*ToDeg(packet.y/radius_of_earth) + home.lng; tell_command.alt = packet.z*1.0e2; tell_command.options = MASK_OPTIONS_RELATIVE_ALT; break; } //case MAV_FRAME_GLOBAL_RELATIVE_ALT: // absolute lat/lng, relative altitude default: { tell_command.lat = 1.0e7 * packet.x; // in as DD converted to * t7 tell_command.lng = 1.0e7 * packet.y; // in as DD converted to * t7 tell_command.alt = packet.z * 1.0e2; tell_command.options = MASK_OPTIONS_RELATIVE_ALT; // store altitude relative!! Always!! break; } } */ // we only are supporting Abs position, relative Alt tell_command.lat = 1.0e7 * packet.x; // in as DD converted to * t7 tell_command.lng = 1.0e7 * packet.y; // in as DD converted to * t7 tell_command.alt = packet.z * 1.0e2; tell_command.options = 1; // store altitude relative to home alt!! Always!! switch (tell_command.id) { // Switch to map APM command fields into MAVLink command fields case MAV_CMD_NAV_LOITER_TURNS: case MAV_CMD_DO_SET_HOME: tell_command.p1 = packet.param1; break; case MAV_CMD_NAV_ROI: tell_command.p1 = packet.param1; // MAV_ROI (aka roi mode) is held in wp's parameter but we actually do nothing with it because we only support pointing at a specific location provided by x,y and z parameters break; case MAV_CMD_CONDITION_YAW: tell_command.p1 = packet.param3; tell_command.alt = packet.param1; tell_command.lat = packet.param2; tell_command.lng = packet.param4; break; case MAV_CMD_NAV_TAKEOFF: tell_command.p1 = 0; break; case MAV_CMD_CONDITION_CHANGE_ALT: tell_command.p1 = packet.param1 * 100; break; case MAV_CMD_NAV_LOITER_TIME: tell_command.p1 = packet.param1; // APM loiter time is in ten second increments break; case MAV_CMD_CONDITION_DELAY: case MAV_CMD_CONDITION_DISTANCE: tell_command.lat = packet.param1; break; case MAV_CMD_DO_JUMP: tell_command.lat = packet.param2; tell_command.p1 = packet.param1; break; case MAV_CMD_DO_REPEAT_SERVO: tell_command.lng = packet.param4; case MAV_CMD_DO_REPEAT_RELAY: case MAV_CMD_DO_CHANGE_SPEED: tell_command.lat = packet.param3; tell_command.alt = packet.param2; tell_command.p1 = packet.param1; break; case MAV_CMD_NAV_WAYPOINT: tell_command.p1 = packet.param1; break; case MAV_CMD_DO_SET_PARAMETER: case MAV_CMD_DO_SET_RELAY: case MAV_CMD_DO_SET_SERVO: tell_command.alt = packet.param2; tell_command.p1 = packet.param1; break; } if(packet.current == 2){ //current = 2 is a flag to tell us this is a "guided mode" waypoint and not for the mission guided_WP = tell_command; // add home alt if needed if (guided_WP.options & MASK_OPTIONS_RELATIVE_ALT){ guided_WP.alt += home.alt; } set_mode(GUIDED); // make any new wp uploaded instant (in case we are already in Guided mode) set_next_WP(&guided_WP); // verify we recevied the command mavlink_msg_waypoint_ack_send( chan, msg->sysid, msg->compid, 0); } else { // Check if receiving waypoints (mission upload expected) if (!waypoint_receiving) break; //Serial.printf("req: %d, seq: %d, total: %d\n", waypoint_request_i,packet.seq, g.command_total.get()); // check if this is the requested waypoint if (packet.seq != waypoint_request_i) break; if(packet.seq != 0) set_cmd_with_index(tell_command, packet.seq); // update waypoint receiving state machine waypoint_timelast_receive = millis(); waypoint_timelast_request = 0; waypoint_request_i++; if (waypoint_request_i == (uint16_t)g.command_total){ uint8_t type = 0; // ok (0), error(1) mavlink_msg_waypoint_ack_send( chan, msg->sysid, msg->compid, type); send_text(SEVERITY_LOW,PSTR("flight plan received")); waypoint_receiving = false; // XXX ignores waypoint radius for individual waypoints, can // only set WP_RADIUS parameter } } break; } case MAVLINK_MSG_ID_PARAM_SET: // 23 { AP_Param *vp; enum ap_var_type var_type; // decode mavlink_param_set_t packet; mavlink_msg_param_set_decode(msg, &packet); if (mavlink_check_target(packet.target_system, packet.target_component)) break; // set parameter char key[ONBOARD_PARAM_NAME_LENGTH+1]; strncpy(key, (char *)packet.param_id, ONBOARD_PARAM_NAME_LENGTH); key[ONBOARD_PARAM_NAME_LENGTH] = 0; // find the requested parameter vp = AP_Param::find(key, &var_type); if ((NULL != vp) && // exists !isnan(packet.param_value) && // not nan !isinf(packet.param_value)) { // not inf // add a small amount before casting parameter values // from float to integer to avoid truncating to the // next lower integer value. float rounding_addition = 0.01; // handle variables with standard type IDs if (var_type == AP_PARAM_FLOAT) { ((AP_Float *)vp)->set_and_save(packet.param_value); } else if (var_type == AP_PARAM_INT32) { #if LOGGING_ENABLED == ENABLED Log_Write_Data(1, ((AP_Int32 *)vp)->get()); #endif if (packet.param_value < 0) rounding_addition = -rounding_addition; float v = packet.param_value+rounding_addition; v = constrain(v, -2147483648.0, 2147483647.0); ((AP_Int32 *)vp)->set_and_save(v); } else if (var_type == AP_PARAM_INT16) { #if LOGGING_ENABLED == ENABLED Log_Write_Data(3, (int32_t)((AP_Int16 *)vp)->get()); #endif if (packet.param_value < 0) rounding_addition = -rounding_addition; float v = packet.param_value+rounding_addition; v = constrain(v, -32768, 32767); ((AP_Int16 *)vp)->set_and_save(v); } else if (var_type == AP_PARAM_INT8) { #if LOGGING_ENABLED == ENABLED Log_Write_Data(4, (int32_t)((AP_Int8 *)vp)->get()); #endif if (packet.param_value < 0) rounding_addition = -rounding_addition; float v = packet.param_value+rounding_addition; v = constrain(v, -128, 127); ((AP_Int8 *)vp)->set_and_save(v); } else { // we don't support mavlink set on this parameter break; } // Report back the new value if we accepted the change // we send the value we actually set, which could be // different from the value sent, in case someone sent // a fractional value to an integer type mavlink_msg_param_value_send( chan, key, vp->cast_to_float(var_type), mav_var_type(var_type), _count_parameters(), -1); // XXX we don't actually know what its index is... } break; } // end case case MAVLINK_MSG_ID_RC_CHANNELS_OVERRIDE: //70 { // allow override of RC channel values for HIL // or for complete GCS control of switch position // and RC PWM values. if(msg->sysid != g.sysid_my_gcs) break; // Only accept control from our gcs mavlink_rc_channels_override_t packet; int16_t v[8]; mavlink_msg_rc_channels_override_decode(msg, &packet); if (mavlink_check_target(packet.target_system,packet.target_component)) break; v[0] = packet.chan1_raw; v[1] = packet.chan2_raw; v[2] = packet.chan3_raw; v[3] = packet.chan4_raw; v[4] = packet.chan5_raw; v[5] = packet.chan6_raw; v[6] = packet.chan7_raw; v[7] = packet.chan8_raw; APM_RC.setHIL(v); break; } #if HIL_MODE != HIL_MODE_DISABLED case MAVLINK_MSG_ID_HIL_STATE: { mavlink_hil_state_t packet; mavlink_msg_hil_state_decode(msg, &packet); float vel = sqrt((packet.vx * (float)packet.vx) + (packet.vy * (float)packet.vy)); float cog = wrap_360(ToDeg(atan2(packet.vx, packet.vy)) * 100); // set gps hil sensor g_gps->setHIL(packet.time_usec/1000, packet.lat*1.0e-7, packet.lon*1.0e-7, packet.alt*1.0e-3, vel*1.0e-2, cog*1.0e-2, 0, 10); if (gps_base_alt == 0) { gps_base_alt = g_gps->altitude; } current_loc.lng = g_gps->longitude; current_loc.lat = g_gps->latitude; current_loc.alt = g_gps->altitude - gps_base_alt; if (!home_is_set) { init_home(); } // rad/sec Vector3f gyros; gyros.x = packet.rollspeed; gyros.y = packet.pitchspeed; gyros.z = packet.yawspeed; // m/s/s Vector3f accels; accels.x = (float)packet.xacc / 1000.0; accels.y = (float)packet.yacc / 1000.0; accels.z = (float)packet.zacc / 1000.0; imu.set_gyro(gyros); imu.set_accel(accels); // set AHRS hil sensor ahrs.setHil(packet.roll,packet.pitch,packet.yaw,packet.rollspeed, packet.pitchspeed,packet.yawspeed); break; } #endif // HIL_MODE != HIL_MODE_DISABLED /* case MAVLINK_MSG_ID_HEARTBEAT: { // We keep track of the last time we received a heartbeat from our GCS for failsafe purposes if(msg->sysid != g.sysid_my_gcs) break; rc_override_fs_timer = millis(); break; } #if HIL_MODE != HIL_MODE_DISABLED // This is used both as a sensor and to pass the location // in HIL_ATTITUDE mode. case MAVLINK_MSG_ID_GPS_RAW: { // decode mavlink_gps_raw_t packet; mavlink_msg_gps_raw_decode(msg, &packet); // set gps hil sensor g_gps->setHIL(packet.usec/1000,packet.lat,packet.lon,packet.alt, packet.v,packet.hdg,0,0); break; } #endif */ #if HIL_MODE == HIL_MODE_SENSORS case MAVLINK_MSG_ID_RAW_IMU: // 28 { // decode mavlink_raw_imu_t packet; mavlink_msg_raw_imu_decode(msg, &packet); // set imu hil sensors // TODO: check scaling for temp/absPress float temp = 70; float absPress = 1; // Serial.printf_P(PSTR("accel:\t%d\t%d\t%d\n"), packet.xacc, packet.yacc, packet.zacc); // Serial.printf_P(PSTR("gyro:\t%d\t%d\t%d\n"), packet.xgyro, packet.ygyro, packet.zgyro); // rad/sec Vector3f gyros; gyros.x = (float)packet.xgyro / 1000.0; gyros.y = (float)packet.ygyro / 1000.0; gyros.z = (float)packet.zgyro / 1000.0; // m/s/s Vector3f accels; accels.x = (float)packet.xacc / 1000.0; accels.y = (float)packet.yacc / 1000.0; accels.z = (float)packet.zacc / 1000.0; imu.set_gyro(gyros); imu.set_accel(accels); compass.setHIL(packet.xmag,packet.ymag,packet.zmag); break; } case MAVLINK_MSG_ID_RAW_PRESSURE: //29 { // decode mavlink_raw_pressure_t packet; mavlink_msg_raw_pressure_decode(msg, &packet); // set pressure hil sensor // TODO: check scaling float temp = 70; barometer.setHIL(temp,packet.press_diff1); break; } #endif // HIL_MODE #if CAMERA == ENABLED case MAVLINK_MSG_ID_DIGICAM_CONFIGURE: { g.camera.configure_msg(msg); break; } case MAVLINK_MSG_ID_DIGICAM_CONTROL: { g.camera.control_msg(msg); break; } #endif // CAMERA == ENABLED #if MOUNT == ENABLED case MAVLINK_MSG_ID_MOUNT_CONFIGURE: { camera_mount.configure_msg(msg); break; } case MAVLINK_MSG_ID_MOUNT_CONTROL: { camera_mount.control_msg(msg); break; } case MAVLINK_MSG_ID_MOUNT_STATUS: { camera_mount.status_msg(msg); break; } #endif // MOUNT == ENABLED case MAVLINK_MSG_ID_RADIO: { mavlink_radio_t packet; mavlink_msg_radio_decode(msg, &packet); // use the state of the transmit buffer in the radio to // control the stream rate, giving us adaptive software // flow control if (packet.txbuf < 20 && stream_slowdown < 100) { // we are very low on space - slow down a lot stream_slowdown += 3; } else if (packet.txbuf < 50 && stream_slowdown < 100) { // we are a bit low on space, slow down slightly stream_slowdown += 1; } else if (packet.txbuf > 95 && stream_slowdown > 10) { // the buffer has plenty of space, speed up a lot stream_slowdown -= 2; } else if (packet.txbuf > 90 && stream_slowdown != 0) { // the buffer has enough space, speed up a bit stream_slowdown--; } break; } #ifdef AP_LIMITS // receive an AP_Limits fence point from GCS and store in EEPROM // receive a fence point from GCS and store in EEPROM case MAVLINK_MSG_ID_FENCE_POINT: { mavlink_fence_point_t packet; mavlink_msg_fence_point_decode(msg, &packet); if (packet.count != geofence_limit.fence_total()) { send_text(SEVERITY_LOW,PSTR("bad fence point")); } else { Vector2l point; point.x = packet.lat*1.0e7; point.y = packet.lng*1.0e7; geofence_limit.set_fence_point_with_index(point, packet.idx); } break; } // send a fence point to GCS case MAVLINK_MSG_ID_FENCE_FETCH_POINT: { mavlink_fence_fetch_point_t packet; mavlink_msg_fence_fetch_point_decode(msg, &packet); if (mavlink_check_target(packet.target_system, packet.target_component)) break; if (packet.idx >= geofence_limit.fence_total()) { send_text(SEVERITY_LOW,PSTR("bad fence point")); } else { Vector2l point = geofence_limit.get_fence_point_with_index(packet.idx); mavlink_msg_fence_point_send(chan, 0, 0, packet.idx, geofence_limit.fence_total(), point.x*1.0e-7, point.y*1.0e-7); } break; } #endif // AP_LIMITS ENABLED } // end switch } // end handle mavlink uint16_t GCS_MAVLINK::_count_parameters() { // if we haven't cached the parameter count yet... if (0 == _parameter_count) { AP_Param *vp; AP_Param::ParamToken token; vp = AP_Param::first(&token, NULL); do { _parameter_count++; } while (NULL != (vp = AP_Param::next_scalar(&token, NULL))); } return _parameter_count; } /** * @brief Send the next pending parameter, called from deferred message * handling code */ void GCS_MAVLINK::queued_param_send() { // Check to see if we are sending parameters if (NULL == _queued_parameter) return; AP_Param *vp; float value; // copy the current parameter and prepare to move to the next vp = _queued_parameter; // if the parameter can be cast to float, report it here and break out of the loop value = vp->cast_to_float(_queued_parameter_type); char param_name[ONBOARD_PARAM_NAME_LENGTH]; vp->copy_name(param_name, sizeof(param_name), true); mavlink_msg_param_value_send( chan, param_name, value, mav_var_type(_queued_parameter_type), _queued_parameter_count, _queued_parameter_index); _queued_parameter = AP_Param::next_scalar(&_queued_parameter_token, &_queued_parameter_type); _queued_parameter_index++; } /** * @brief Send the next pending waypoint, called from deferred message * handling code */ void GCS_MAVLINK::queued_waypoint_send() { if (waypoint_receiving && waypoint_request_i < (unsigned)g.command_total) { mavlink_msg_waypoint_request_send( chan, waypoint_dest_sysid, waypoint_dest_compid, waypoint_request_i); } } /* a delay() callback that processes MAVLink packets. We set this as the callback in long running library initialisation routines to allow MAVLink to process packets while waiting for the initialisation to complete */ static void mavlink_delay(unsigned long t) { uint32_t tstart; static uint32_t last_1hz, last_50hz, last_5s; if (in_mavlink_delay) { // this should never happen, but let's not tempt fate by // letting the stack grow too much delay(t); return; } in_mavlink_delay = true; tstart = millis(); do { uint32_t tnow = millis(); if (tnow - last_1hz > 1000) { last_1hz = tnow; gcs_send_message(MSG_HEARTBEAT); gcs_send_message(MSG_EXTENDED_STATUS1); } if (tnow - last_50hz > 20) { last_50hz = tnow; gcs_update(); gcs_data_stream_send(); } if (tnow - last_5s > 5000) { last_5s = tnow; gcs_send_text_P(SEVERITY_LOW, PSTR("Initialising APM...")); } delay(1); #if USB_MUX_PIN > 0 check_usb_mux(); #endif } while (millis() - tstart < t); in_mavlink_delay = false; } /* send a message on both GCS links */ static void gcs_send_message(enum ap_message id) { gcs0.send_message(id); if (gcs3.initialised) { gcs3.send_message(id); } } /* send data streams in the given rate range on both links */ static void gcs_data_stream_send(void) { gcs0.data_stream_send(); if (gcs3.initialised) { gcs3.data_stream_send(); } } /* look for incoming commands on the GCS links */ static void gcs_update(void) { gcs0.update(); if (gcs3.initialised) { gcs3.update(); } } static void gcs_send_text(gcs_severity severity, const char *str) { gcs0.send_text(severity, str); if (gcs3.initialised) { gcs3.send_text(severity, str); } } static void gcs_send_text_P(gcs_severity severity, const prog_char_t *str) { gcs0.send_text(severity, str); if (gcs3.initialised) { gcs3.send_text(severity, str); } } /* send a low priority formatted message to the GCS only one fits in the queue, so if you send more than one before the last one gets into the serial buffer then the old one will be lost */ static void gcs_send_text_fmt(const prog_char_t *fmt, ...) { char fmtstr[40]; va_list ap; uint8_t i; for (i=0; i