/// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*- /* This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program. If not, see . */ #pragma once /* This is the main Copter class */ //////////////////////////////////////////////////////////////////////////////// // Header includes //////////////////////////////////////////////////////////////////////////////// #include #include #include #include // Common dependencies #include #include #include #include #include // Application dependencies #include #include // Serial manager library #include // ArduPilot GPS library #include // ArduPilot Mega Flash Memory Library #include // ArduPilot Mega Analog to Digital Converter Library #include #include // ArduPilot Mega Magnetometer Library #include // ArduPilot Mega Vector/Matrix math Library #include // interface and maths for accelerometer calibration #include // ArduPilot Mega Inertial Sensor (accel & gyro) Library #include #include #include #include // Mission command library #include // PID library #include // PID library (2-axis) #include // Heli specific Rate PID library #include // P library #include // Attitude control library #include // Attitude control library for traditional helicopter #include // Position control library #include // RC Channel Library #include // AP Motors library #include // Range finder library #include // Optical Flow library #include // RSSI Library #include // Filter library #include // APM FIFO Buffer #include // APM relay #include #include // Photo or video camera #include // Camera/Antenna mount #include // needed for AHRS build #include // needed for AHRS build #include // ArduPilot Mega inertial navigation library #include // ArduCopter waypoint navigation library #include // circle navigation library #include // ArduPilot Mega Declination Helper Library #include // Arducopter Fence library #include // Arducopter stop at fence library #include // main loop scheduler #include // RC input mapping library #include // Notify library #include // Battery monitor library #include // board configuration library #include // Landing Gear library #include #include #include #include // Pilot input handling library #include // Heli specific pilot input handling library #include // Configuration #include "defines.h" #include "config.h" #include "GCS_Mavlink.h" #include "AP_Rally.h" // Rally point library // libraries which are dependent on #defines in defines.h and/or config.h #if SPRAYER == ENABLED #include // crop sprayer library #endif #if EPM_ENABLED == ENABLED #include // EPM cargo gripper stuff #endif #if PARACHUTE == ENABLED #include // Parachute release library #endif #if PRECISION_LANDING == ENABLED #include #include #endif #if FRSKY_TELEM_ENABLED == ENABLED #include #endif #if ADVANCED_FAILSAFE == ENABLED #include "afs_copter.h" #endif // Local modules #include "Parameters.h" #include "avoidance_adsb.h" #if CONFIG_HAL_BOARD == HAL_BOARD_SITL #include #endif class Copter : public AP_HAL::HAL::Callbacks { public: friend class GCS_MAVLINK_Copter; friend class AP_Rally_Copter; friend class Parameters; friend class ParametersG2; friend class AP_Avoidance_Copter; #if ADVANCED_FAILSAFE == ENABLED friend class AP_AdvancedFailsafe_Copter; #endif Copter(void); // HAL::Callbacks implementation. void setup() override; void loop() override; private: // key aircraft parameters passed to multiple libraries AP_Vehicle::MultiCopter aparm; // cliSerial isn't strictly necessary - it is an alias for hal.console. It may // be deprecated in favor of hal.console in later releases. AP_HAL::BetterStream* cliSerial; // Global parameters are all contained within the 'g' class. Parameters g; ParametersG2 g2; // main loop scheduler AP_Scheduler scheduler; // AP_Notify instance AP_Notify notify; // used to detect MAVLink acks from GCS to stop compassmot uint8_t command_ack_counter; // has a log download started? bool in_log_download; // primary input control channels RC_Channel *channel_roll; RC_Channel *channel_pitch; RC_Channel *channel_throttle; RC_Channel *channel_yaw; // Dataflash DataFlash_Class DataFlash; AP_GPS gps; // flight modes convenience array AP_Int8 *flight_modes; AP_Baro barometer; Compass compass; AP_InertialSensor ins; RangeFinder rangefinder {serial_manager}; struct { bool enabled:1; bool alt_healthy:1; // true if we can trust the altitude from the rangefinder int16_t alt_cm; // tilt compensated altitude (in cm) from rangefinder uint32_t last_healthy_ms; LowPassFilterFloat alt_cm_filt; // altitude filter } rangefinder_state = { false, false, 0, 0 }; AP_RPM rpm_sensor; // Inertial Navigation EKF NavEKF EKF{&ahrs, barometer, rangefinder}; NavEKF2 EKF2{&ahrs, barometer, rangefinder}; AP_AHRS_NavEKF ahrs{ins, barometer, gps, rangefinder, EKF, EKF2, AP_AHRS_NavEKF::FLAG_ALWAYS_USE_EKF}; #if CONFIG_HAL_BOARD == HAL_BOARD_SITL SITL::SITL sitl; #endif // Mission library AP_Mission mission; // Optical flow sensor #if OPTFLOW == ENABLED OpticalFlow optflow{ahrs}; #endif // gnd speed limit required to observe optical flow sensor limits float ekfGndSpdLimit; // scale factor applied to velocity controller gain to prevent optical flow noise causing excessive angle demand noise float ekfNavVelGainScaler; // system time in milliseconds of last recorded yaw reset from ekf uint32_t ekfYawReset_ms = 0; // GCS selection AP_SerialManager serial_manager; static const uint8_t num_gcs = MAVLINK_COMM_NUM_BUFFERS; GCS_MAVLINK_Copter gcs[MAVLINK_COMM_NUM_BUFFERS]; // User variables #ifdef USERHOOK_VARIABLES # include USERHOOK_VARIABLES #endif // Documentation of GLobals: union { struct { uint8_t unused1 : 1; // 0 uint8_t simple_mode : 2; // 1,2 // This is the state of simple mode : 0 = disabled ; 1 = SIMPLE ; 2 = SUPERSIMPLE uint8_t pre_arm_rc_check : 1; // 3 // true if rc input pre-arm checks have been completed successfully uint8_t pre_arm_check : 1; // 4 // true if all pre-arm checks (rc, accel calibration, gps lock) have been performed uint8_t auto_armed : 1; // 5 // stops auto missions from beginning until throttle is raised uint8_t logging_started : 1; // 6 // true if dataflash logging has started uint8_t land_complete : 1; // 7 // true if we have detected a landing uint8_t new_radio_frame : 1; // 8 // Set true if we have new PWM data to act on from the Radio uint8_t usb_connected : 1; // 9 // true if APM is powered from USB connection uint8_t rc_receiver_present : 1; // 10 // true if we have an rc receiver present (i.e. if we've ever received an update uint8_t compass_mot : 1; // 11 // true if we are currently performing compassmot calibration uint8_t motor_test : 1; // 12 // true if we are currently performing the motors test uint8_t initialised : 1; // 13 // true once the init_ardupilot function has completed. Extended status to GCS is not sent until this completes uint8_t land_complete_maybe : 1; // 14 // true if we may have landed (less strict version of land_complete) uint8_t throttle_zero : 1; // 15 // true if the throttle stick is at zero, debounced, determines if pilot intends shut-down when not using motor interlock uint8_t system_time_set : 1; // 16 // true if the system time has been set from the GPS uint8_t gps_base_pos_set : 1; // 17 // true when the gps base position has been set (used for RTK gps only) enum HomeState home_state : 2; // 18,19 // home status (unset, set, locked) uint8_t using_interlock : 1; // 20 // aux switch motor interlock function is in use uint8_t motor_emergency_stop : 1; // 21 // motor estop switch, shuts off motors when enabled uint8_t land_repo_active : 1; // 22 // true if the pilot is overriding the landing position uint8_t motor_interlock_switch : 1; // 23 // true if pilot is requesting motor interlock enable uint8_t in_arming_delay : 1; // 24 // true while we are armed but waiting to spin motors }; uint32_t value; } ap; // This is the state of the flight control system // There are multiple states defined such as STABILIZE, ACRO, control_mode_t control_mode; mode_reason_t control_mode_reason = MODE_REASON_UNKNOWN; control_mode_t prev_control_mode; mode_reason_t prev_control_mode_reason = MODE_REASON_UNKNOWN; // Structure used to detect changes in the flight mode control switch struct { int8_t debounced_switch_position; // currently used switch position int8_t last_switch_position; // switch position in previous iteration uint32_t last_edge_time_ms; // system time that switch position was last changed } control_switch_state; struct { bool running; float max_speed; float alt_delta; uint32_t start_ms; } takeoff_state; uint32_t precland_last_update_ms; // altitude below which we do no navigation in auto takeoff float auto_takeoff_no_nav_alt_cm; RCMapper rcmap; // board specific config AP_BoardConfig BoardConfig; // receiver RSSI uint8_t receiver_rssi; // Failsafe struct { uint8_t rc_override_active : 1; // 0 // true if rc control are overwritten by ground station uint8_t radio : 1; // 1 // A status flag for the radio failsafe uint8_t battery : 1; // 2 // A status flag for the battery failsafe uint8_t gcs : 1; // 4 // A status flag for the ground station failsafe uint8_t ekf : 1; // 5 // true if ekf failsafe has occurred uint8_t terrain : 1; // 6 // true if the missing terrain data failsafe has occurred uint8_t adsb : 1; // 7 // true if an adsb related failsafe has occurred int8_t radio_counter; // number of iterations with throttle below throttle_fs_value uint32_t last_heartbeat_ms; // the time when the last HEARTBEAT message arrived from a GCS - used for triggering gcs failsafe uint32_t terrain_first_failure_ms; // the first time terrain data access failed - used to calculate the duration of the failure uint32_t terrain_last_failure_ms; // the most recent time terrain data access failed } failsafe; // sensor health for logging struct { uint8_t baro : 1; // true if baro is healthy uint8_t compass : 1; // true if compass is healthy } sensor_health; // setup FRAME_MAV_TYPE #if (FRAME_CONFIG == QUAD_FRAME) #define FRAME_MAV_TYPE MAV_TYPE_QUADROTOR #elif (FRAME_CONFIG == TRI_FRAME) #define FRAME_MAV_TYPE MAV_TYPE_TRICOPTER #elif (FRAME_CONFIG == HEXA_FRAME || FRAME_CONFIG == Y6_FRAME) #define FRAME_MAV_TYPE MAV_TYPE_HEXAROTOR #elif (FRAME_CONFIG == OCTA_FRAME || FRAME_CONFIG == OCTA_QUAD_FRAME) #define FRAME_MAV_TYPE MAV_TYPE_OCTOROTOR #elif (FRAME_CONFIG == HELI_FRAME) #define FRAME_MAV_TYPE MAV_TYPE_HELICOPTER #elif (FRAME_CONFIG == SINGLE_FRAME || FRAME_CONFIG == COAX_FRAME) //because mavlink did not define a singlecopter, we use a quad #define FRAME_MAV_TYPE MAV_TYPE_QUADROTOR #else #error Unrecognised frame type #endif // Motor Output #if FRAME_CONFIG == QUAD_FRAME #define MOTOR_CLASS AP_MotorsQuad #elif FRAME_CONFIG == TRI_FRAME #define MOTOR_CLASS AP_MotorsTri #elif FRAME_CONFIG == HEXA_FRAME #define MOTOR_CLASS AP_MotorsHexa #elif FRAME_CONFIG == Y6_FRAME #define MOTOR_CLASS AP_MotorsY6 #elif FRAME_CONFIG == OCTA_FRAME #define MOTOR_CLASS AP_MotorsOcta #elif FRAME_CONFIG == OCTA_QUAD_FRAME #define MOTOR_CLASS AP_MotorsOctaQuad #elif FRAME_CONFIG == HELI_FRAME #define MOTOR_CLASS AP_MotorsHeli_Single #elif FRAME_CONFIG == SINGLE_FRAME #define MOTOR_CLASS AP_MotorsSingle #elif FRAME_CONFIG == COAX_FRAME #define MOTOR_CLASS AP_MotorsCoax #else #error Unrecognised frame type #endif MOTOR_CLASS motors; // GPS variables // Sometimes we need to remove the scaling for distance calcs float scaleLongDown; // Location & Navigation int32_t wp_bearing; // The location of home in relation to the copter in centi-degrees int32_t home_bearing; // distance between plane and home in cm int32_t home_distance; // distance between plane and next waypoint in cm. uint32_t wp_distance; LandStateType land_state = LandStateType_FlyToLocation; // records state of land (flying to location, descending) // Auto AutoMode auto_mode; // controls which auto controller is run // Guided GuidedMode guided_mode; // controls which controller is run (pos or vel) // RTL RTLState rtl_state; // records state of rtl (initial climb, returning home, etc) bool rtl_state_complete; // set to true if the current state is completed struct { // NEU w/ Z element alt-above-ekf-origin unless use_terrain is true in which case Z element is alt-above-terrain Location_Class origin_point; Location_Class climb_target; Location_Class return_target; Location_Class descent_target; bool land; bool terrain_used; } rtl_path; // Circle bool circle_pilot_yaw_override; // true if pilot is overriding yaw // SIMPLE Mode // Used to track the orientation of the copter for Simple mode. This value is reset at each arming // or in SuperSimple mode when the copter leaves a 20m radius from home. float simple_cos_yaw; float simple_sin_yaw; int32_t super_simple_last_bearing; float super_simple_cos_yaw; float super_simple_sin_yaw; // Stores initial bearing when armed - initial simple bearing is modified in super simple mode so not suitable int32_t initial_armed_bearing; // Throttle variables int16_t desired_climb_rate; // pilot desired climb rate - for logging purposes only // Loiter control uint16_t loiter_time_max; // How long we should stay in Loiter Mode for mission scripting (time in seconds) uint32_t loiter_time; // How long have we been loitering - The start time in millis // Brake uint32_t brake_timeout_start; uint32_t brake_timeout_ms; // Delay the next navigation command int32_t nav_delay_time_max; // used for delaying the navigation commands (eg land,takeoff etc.) uint32_t nav_delay_time_start; // Flip Vector3f flip_orig_attitude; // original copter attitude before flip // throw mode state struct { ThrowModeStage stage; ThrowModeStage prev_stage; uint32_t last_log_ms; bool nextmode_attempted; uint32_t free_fall_start_ms; // system time free fall was detected float free_fall_start_velz; // vertical velocity when free fall was detected } throw_state = {Throw_Disarmed, Throw_Disarmed, 0, false, 0, 0.0f}; // Battery Sensors AP_BattMonitor battery; // FrSky telemetry support #if FRSKY_TELEM_ENABLED == ENABLED AP_Frsky_Telem frsky_telemetry; #endif // Altitude // The cm/s we are moving up or down based on filtered data - Positive = UP int16_t climb_rate; float target_rangefinder_alt; // desired altitude in cm above the ground int32_t baro_alt; // barometer altitude in cm above home float baro_climbrate; // barometer climbrate in cm/s LowPassFilterVector3f land_accel_ef_filter; // accelerations for land and crash detector tests // filtered pilot's throttle input used to cancel landing if throttle held high LowPassFilterFloat rc_throttle_control_in_filter; // 3D Location vectors // Current location of the copter (altitude is relative to home) Location_Class current_loc; // Navigation Yaw control // auto flight mode's yaw mode uint8_t auto_yaw_mode; // Yaw will point at this location if auto_yaw_mode is set to AUTO_YAW_ROI Vector3f roi_WP; // bearing from current location to the yaw_look_at_WP float yaw_look_at_WP_bearing; // yaw used for YAW_LOOK_AT_HEADING yaw_mode int32_t yaw_look_at_heading; // Deg/s we should turn int16_t yaw_look_at_heading_slew; // heading when in yaw_look_ahead_bearing float yaw_look_ahead_bearing; // Delay Mission Scripting Command int32_t condition_value; // used in condition commands (eg delay, change alt, etc.) uint32_t condition_start; // IMU variables // Integration time (in seconds) for the gyros (DCM algorithm) // Updated with the fast loop float G_Dt; // Inertial Navigation AP_InertialNav_NavEKF inertial_nav; // Attitude, Position and Waypoint navigation objects // To-Do: move inertial nav up or other navigation variables down here #if FRAME_CONFIG == HELI_FRAME AC_AttitudeControl_Heli attitude_control; #else AC_AttitudeControl_Multi attitude_control; #endif AC_PosControl pos_control; AC_Avoid avoid; AC_WPNav wp_nav; AC_Circle circle_nav; // Performance monitoring int16_t pmTest1; // System Timers // -------------- // Time in microseconds of main control loop uint32_t fast_loopTimer; // Counter of main loop executions. Used for performance monitoring and failsafe processing uint16_t mainLoop_count; // Loiter timer - Records how long we have been in loiter uint32_t rtl_loiter_start_time; // arm_time_ms - Records when vehicle was armed. Will be Zero if we are disarmed. uint32_t arm_time_ms; // Used to exit the roll and pitch auto trim function uint8_t auto_trim_counter; // Reference to the relay object AP_Relay relay; // handle repeated servo and relay events AP_ServoRelayEvents ServoRelayEvents; // Reference to the camera object (it uses the relay object inside it) #if CAMERA == ENABLED AP_Camera camera; #endif // Camera/Antenna mount tracking and stabilisation stuff #if MOUNT == ENABLED // current_loc uses the baro/gps soloution for altitude rather than gps only. AP_Mount camera_mount; #endif // AC_Fence library to reduce fly-aways #if AC_FENCE == ENABLED AC_Fence fence; #endif // Rally library #if AC_RALLY == ENABLED AP_Rally_Copter rally; #endif // RSSI AP_RSSI rssi; // Crop Sprayer #if SPRAYER == ENABLED AC_Sprayer sprayer; #endif // EPM Cargo Griper #if EPM_ENABLED == ENABLED AP_EPM epm; #endif // Parachute release #if PARACHUTE == ENABLED AP_Parachute parachute; #endif // Landing Gear Controller AP_LandingGear landinggear; // terrain handling #if AP_TERRAIN_AVAILABLE && AC_TERRAIN AP_Terrain terrain; #endif // Precision Landing #if PRECISION_LANDING == ENABLED AC_PrecLand precland; #endif // Pilot Input Management Library // Only used for Helicopter for AC3.3, to be expanded to include Multirotor // child class for AC3.4 #if FRAME_CONFIG == HELI_FRAME AC_InputManager_Heli input_manager; #endif AP_ADSB adsb {ahrs}; // avoidance of adsb enabled vehicles (normally manned vheicles) AP_Avoidance_Copter avoidance_adsb{ahrs, adsb}; // use this to prevent recursion during sensor init bool in_mavlink_delay; // true if we are out of time in our event timeslice bool gcs_out_of_time; // last valid RC input time uint32_t last_radio_update_ms; // Top-level logic // setup the var_info table AP_Param param_loader; #if FRAME_CONFIG == HELI_FRAME // Mode filter to reject RC Input glitches. Filter size is 5, and it draws the 4th element, so it can reject 3 low glitches, // and 1 high glitch. This is because any "off" glitches can be highly problematic for a helicopter running an ESC // governor. Even a single "off" frame can cause the rotor to slow dramatically and take a long time to restart. ModeFilterInt16_Size5 rotor_speed_deglitch_filter {4}; // Tradheli flags struct { uint8_t dynamic_flight : 1; // 0 // true if we are moving at a significant speed (used to turn on/off leaky I terms) uint8_t init_targets_on_arming : 1; // 1 // true if we have been disarmed, and need to reset rate controller targets when we arm } heli_flags; int16_t hover_roll_trim_scalar_slew; #endif // ground effect detector struct { bool takeoff_expected; bool touchdown_expected; uint32_t takeoff_time_ms; float takeoff_alt_cm; } gndeffect_state; static const AP_Scheduler::Task scheduler_tasks[]; static const AP_Param::Info var_info[]; static const struct LogStructure log_structure[]; void compass_accumulate(void); void compass_cal_update(void); void barometer_accumulate(void); void perf_update(void); void fast_loop(); void rc_loop(); void throttle_loop(); void update_mount(); void update_trigger(void); void update_batt_compass(void); void ten_hz_logging_loop(); void twentyfive_hz_logging(); void three_hz_loop(); void one_hz_loop(); void update_GPS(void); void init_simple_bearing(); void update_simple_mode(void); void update_super_simple_bearing(bool force_update); void read_AHRS(void); void update_altitude(); void set_home_state(enum HomeState new_home_state); bool home_is_set(); void set_auto_armed(bool b); void set_simple_mode(uint8_t b); void set_failsafe_radio(bool b); void set_failsafe_battery(bool b); void set_failsafe_gcs(bool b); void set_land_complete(bool b); void set_land_complete_maybe(bool b); void set_pre_arm_check(bool b); void set_pre_arm_rc_check(bool b); bool rc_calibration_checks(bool display_failure); bool gps_checks(bool display_failure); bool fence_checks(bool display_failure); bool compass_checks(bool display_failure); bool ins_checks(bool display_failure); bool board_voltage_checks(bool display_failure); bool parameter_checks(bool display_failure); bool pilot_throttle_checks(bool display_failure); bool barometer_checks(bool display_failure); void update_using_interlock(); void set_motor_emergency_stop(bool b); float get_smoothing_gain(); void get_pilot_desired_lean_angles(float roll_in, float pitch_in, float &roll_out, float &pitch_out, float angle_max); float get_pilot_desired_yaw_rate(int16_t stick_angle); void check_ekf_yaw_reset(); float get_roi_yaw(); float get_look_ahead_yaw(); void update_throttle_hover(); void set_throttle_takeoff(); float get_pilot_desired_throttle(int16_t throttle_control); float get_pilot_desired_climb_rate(float throttle_control); float get_non_takeoff_throttle(); float get_surface_tracking_climb_rate(int16_t target_rate, float current_alt_target, float dt); void auto_takeoff_set_start_alt(void); void auto_takeoff_attitude_run(float target_yaw_rate); void set_accel_throttle_I_from_pilot_throttle(float pilot_throttle); void update_poscon_alt_max(); void rotate_body_frame_to_NE(float &x, float &y); void gcs_send_heartbeat(void); void gcs_send_deferred(void); void send_heartbeat(mavlink_channel_t chan); void send_attitude(mavlink_channel_t chan); void send_limits_status(mavlink_channel_t chan); void send_extended_status1(mavlink_channel_t chan); void send_location(mavlink_channel_t chan); void send_nav_controller_output(mavlink_channel_t chan); void send_simstate(mavlink_channel_t chan); void send_hwstatus(mavlink_channel_t chan); void send_servo_out(mavlink_channel_t chan); void send_vfr_hud(mavlink_channel_t chan); void send_current_waypoint(mavlink_channel_t chan); void send_rangefinder(mavlink_channel_t chan); void send_rpm(mavlink_channel_t chan); void rpm_update(); void button_update(); void send_pid_tuning(mavlink_channel_t chan); void gcs_send_message(enum ap_message id); void gcs_send_mission_item_reached_message(uint16_t mission_index); void gcs_data_stream_send(void); void gcs_check_input(void); void gcs_send_text(MAV_SEVERITY severity, const char *str); void do_erase_logs(void); void Log_Write_AutoTune(uint8_t axis, uint8_t tune_step, float meas_target, float meas_min, float meas_max, float new_gain_rp, float new_gain_rd, float new_gain_sp, float new_ddt); void Log_Write_AutoTuneDetails(float angle_cd, float rate_cds); void Log_Write_Current(); void Log_Write_Optflow(); void Log_Write_Nav_Tuning(); void Log_Write_Control_Tuning(); void Log_Write_Performance(); void Log_Write_Attitude(); void Log_Write_MotBatt(); void Log_Write_Event(uint8_t id); void Log_Write_Data(uint8_t id, int32_t value); void Log_Write_Data(uint8_t id, uint32_t value); void Log_Write_Data(uint8_t id, int16_t value); void Log_Write_Data(uint8_t id, uint16_t value); void Log_Write_Data(uint8_t id, float value); void Log_Write_Error(uint8_t sub_system, uint8_t error_code); void Log_Write_Baro(void); void Log_Write_Parameter_Tuning(uint8_t param, float tuning_val, int16_t control_in, int16_t tune_low, int16_t tune_high); void Log_Write_Home_And_Origin(); void Log_Sensor_Health(); #if FRAME_CONFIG == HELI_FRAME void Log_Write_Heli(void); #endif void Log_Write_Precland(); void Log_Write_GuidedTarget(uint8_t target_type, const Vector3f& pos_target, const Vector3f& vel_target); void Log_Write_Throw(ThrowModeStage stage, float velocity, float velocity_z, float accel, float ef_accel_z, bool throw_detect, bool attitude_ok, bool height_ok, bool position_ok); void Log_Write_Vehicle_Startup_Messages(); void Log_Read(uint16_t log_num, uint16_t start_page, uint16_t end_page); void start_logging() ; void load_parameters(void); void convert_pid_parameters(void); void userhook_init(); void userhook_FastLoop(); void userhook_50Hz(); void userhook_MediumLoop(); void userhook_SlowLoop(); void userhook_SuperSlowLoop(); void update_home_from_EKF(); void set_home_to_current_location_inflight(); bool set_home_to_current_location(); bool set_home_to_current_location_and_lock(); bool set_home_and_lock(const Location& loc); bool set_home(const Location& loc); bool far_from_EKF_origin(const Location& loc); void set_system_time_from_GPS(); void exit_mission(); void do_RTL(void); bool verify_takeoff(); bool verify_land(); bool verify_loiter_unlimited(); bool verify_loiter_time(); bool verify_RTL(); bool verify_wait_delay(); bool verify_within_distance(); bool verify_yaw(); void do_take_picture(); void log_picture(); uint8_t mavlink_compassmot(mavlink_channel_t chan); void delay(uint32_t ms); bool acro_init(bool ignore_checks); void acro_run(); void get_pilot_desired_angle_rates(int16_t roll_in, int16_t pitch_in, int16_t yaw_in, float &roll_out, float &pitch_out, float &yaw_out); bool althold_init(bool ignore_checks); void althold_run(); bool auto_init(bool ignore_checks); void auto_run(); void auto_takeoff_start(const Location& dest_loc); void auto_takeoff_run(); void auto_wp_start(const Vector3f& destination); void auto_wp_start(const Location_Class& dest_loc); void auto_wp_run(); void auto_spline_run(); void auto_land_start(); void auto_land_start(const Vector3f& destination); void auto_land_run(); void auto_rtl_start(); void auto_rtl_run(); void auto_circle_movetoedge_start(const Location_Class &circle_center, float radius_m); void auto_circle_start(); void auto_circle_run(); void auto_nav_guided_start(); void auto_nav_guided_run(); bool auto_loiter_start(); void auto_loiter_run(); uint8_t get_default_auto_yaw_mode(bool rtl); void set_auto_yaw_mode(uint8_t yaw_mode); void set_auto_yaw_look_at_heading(float angle_deg, float turn_rate_dps, int8_t direction, uint8_t relative_angle); void set_auto_yaw_roi(const Location &roi_location); float get_auto_heading(void); bool autotune_init(bool ignore_checks); void autotune_stop(); bool autotune_start(bool ignore_checks); void autotune_run(); void autotune_attitude_control(); void autotune_backup_gains_and_initialise(); void autotune_load_orig_gains(); void autotune_load_tuned_gains(); void autotune_load_intra_test_gains(); void autotune_load_twitch_gains(); void autotune_save_tuning_gains(); void autotune_update_gcs(uint8_t message_id); bool autotune_roll_enabled(); bool autotune_pitch_enabled(); bool autotune_yaw_enabled(); void autotune_twitching_test(float measurement, float target, float &measurement_min, float &measurement_max); void autotune_updating_d_up(float &tune_d, float tune_d_min, float tune_d_max, float tune_d_step_ratio, float &tune_p, float tune_p_min, float tune_p_max, float tune_p_step_ratio, float target, float measurement_min, float measurement_max); void autotune_updating_d_down(float &tune_d, float tune_d_min, float tune_d_step_ratio, float &tune_p, float tune_p_min, float tune_p_max, float tune_p_step_ratio, float target, float measurement_min, float measurement_max); void autotune_updating_p_down(float &tune_p, float tune_p_min, float tune_p_step_ratio, float target, float measurement_max); void autotune_updating_p_up(float &tune_p, float tune_p_max, float tune_p_step_ratio, float target, float measurement_max); void autotune_updating_p_up_d_down(float &tune_d, float tune_d_min, float tune_d_step_ratio, float &tune_p, float tune_p_min, float tune_p_max, float tune_p_step_ratio, float target, float measurement_min, float measurement_max); void autotune_twitching_measure_acceleration(float &rate_of_change, float rate_measurement, float &rate_measurement_max); void avoidance_adsb_update(void); #if ADVANCED_FAILSAFE == ENABLED void afs_fs_check(void); #endif bool brake_init(bool ignore_checks); void brake_run(); void brake_timeout_to_loiter_ms(uint32_t timeout_ms); bool circle_init(bool ignore_checks); void circle_run(); bool drift_init(bool ignore_checks); void drift_run(); float get_throttle_assist(float velz, float pilot_throttle_scaled); bool flip_init(bool ignore_checks); void flip_run(); bool guided_init(bool ignore_checks); bool guided_takeoff_start(float final_alt_above_home); void guided_pos_control_start(); void guided_vel_control_start(); void guided_posvel_control_start(); void guided_angle_control_start(); bool guided_set_destination(const Vector3f& destination); bool guided_set_destination(const Location_Class& dest_loc); void guided_set_velocity(const Vector3f& velocity); void guided_set_destination_posvel(const Vector3f& destination, const Vector3f& velocity); void guided_set_angle(const Quaternion &q, float climb_rate_cms, bool use_yaw_rate, float yaw_rate_rads); void guided_run(); void guided_takeoff_run(); void guided_pos_control_run(); void guided_vel_control_run(); void guided_posvel_control_run(); void guided_angle_control_run(); void guided_set_desired_velocity_with_accel_and_fence_limits(const Vector3f& vel_des); void guided_limit_clear(); void guided_limit_set(uint32_t timeout_ms, float alt_min_cm, float alt_max_cm, float horiz_max_cm); void guided_limit_init_time_and_pos(); bool guided_limit_check(); bool guided_nogps_init(bool ignore_checks); void guided_nogps_run(); bool land_init(bool ignore_checks); void land_run(); void land_gps_run(); void land_nogps_run(); int32_t land_get_alt_above_ground(void); void land_run_vertical_control(bool pause_descent = false); void land_run_horizontal_control(); void land_do_not_use_GPS(); void set_mode_land_with_pause(mode_reason_t reason); bool landing_with_GPS(); bool loiter_init(bool ignore_checks); void loiter_run(); bool poshold_init(bool ignore_checks); void poshold_run(); void poshold_update_pilot_lean_angle(float &lean_angle_filtered, float &lean_angle_raw); int16_t poshold_mix_controls(float mix_ratio, int16_t first_control, int16_t second_control); void poshold_update_brake_angle_from_velocity(int16_t &brake_angle, float velocity); void poshold_update_wind_comp_estimate(); void poshold_get_wind_comp_lean_angles(int16_t &roll_angle, int16_t &pitch_angle); void poshold_roll_controller_to_pilot_override(); void poshold_pitch_controller_to_pilot_override(); // Throw to launch functionality bool throw_init(bool ignore_checks); void throw_run(); bool throw_detected(); bool throw_attitude_good(); bool throw_height_good(); bool throw_position_good(); bool rtl_init(bool ignore_checks); void rtl_restart_without_terrain(); void rtl_run(); void rtl_climb_start(); void rtl_return_start(); void rtl_climb_return_run(); void rtl_loiterathome_start(); void rtl_loiterathome_run(); void rtl_descent_start(); void rtl_descent_run(); void rtl_land_start(); void rtl_land_run(); void rtl_build_path(bool terrain_following_allowed); void rtl_compute_return_target(bool terrain_following_allowed); bool sport_init(bool ignore_checks); void sport_run(); bool stabilize_init(bool ignore_checks); void stabilize_run(); void crash_check(); void parachute_check(); void parachute_release(); void parachute_manual_release(); // support for AP_Avoidance custom flight mode, AVOID_ADSB bool avoid_adsb_init(bool ignore_checks); void avoid_adsb_run(); bool avoid_adsb_set_velocity(const Vector3f& velocity_neu); void ekf_check(); bool ekf_over_threshold(); void failsafe_ekf_event(); void failsafe_ekf_off_event(void); void esc_calibration_startup_check(); void esc_calibration_passthrough(); void esc_calibration_auto(); bool should_disarm_on_failsafe(); void failsafe_radio_on_event(); void failsafe_radio_off_event(); void failsafe_battery_event(void); void failsafe_gcs_check(); void failsafe_gcs_off_event(void); void failsafe_terrain_check(); void failsafe_terrain_set_status(bool data_ok); void failsafe_terrain_on_event(); void set_mode_RTL_or_land_with_pause(mode_reason_t reason); void update_events(); void failsafe_enable(); void failsafe_disable(); void fence_check(); void fence_send_mavlink_status(mavlink_channel_t chan); bool set_mode(control_mode_t mode, mode_reason_t reason); bool gcs_set_mode(uint8_t mode) { return set_mode((control_mode_t)mode, MODE_REASON_GCS_COMMAND); } void update_flight_mode(); void exit_mode(control_mode_t old_control_mode, control_mode_t new_control_mode); bool mode_requires_GPS(control_mode_t mode); bool mode_has_manual_throttle(control_mode_t mode); bool mode_allows_arming(control_mode_t mode, bool arming_from_gcs); void notify_flight_mode(control_mode_t mode); void heli_init(); void check_dynamic_flight(void); void update_heli_control_dynamics(void); void heli_update_landing_swash(); void heli_update_rotor_speed_targets(); bool heli_acro_init(bool ignore_checks); void heli_acro_run(); bool heli_stabilize_init(bool ignore_checks); void heli_stabilize_run(); void read_inertia(); bool land_complete_maybe(); void update_land_and_crash_detectors(); void update_land_detector(); void update_throttle_thr_mix(); void update_ground_effect_detector(void); void landinggear_update(); void update_notify(); void motor_test_output(); bool mavlink_motor_test_check(mavlink_channel_t chan, bool check_rc); uint8_t mavlink_motor_test_start(mavlink_channel_t chan, uint8_t motor_seq, uint8_t throttle_type, uint16_t throttle_value, float timeout_sec); void motor_test_stop(); void arm_motors_check(); void auto_disarm_check(); bool init_arm_motors(bool arming_from_gcs); void update_arming_checks(void); bool all_arming_checks_passing(bool arming_from_gcs); bool pre_arm_checks(bool display_failure); void pre_arm_rc_checks(); bool pre_arm_gps_checks(bool display_failure); bool pre_arm_ekf_attitude_check(); bool pre_arm_terrain_check(bool display_failure); bool arm_checks(bool display_failure, bool arming_from_gcs); void init_disarm_motors(); void motors_output(); void lost_vehicle_check(); void run_nav_updates(void); void calc_distance_and_bearing(); void calc_wp_distance(); void calc_wp_bearing(); void calc_home_distance_and_bearing(); void run_autopilot(); void perf_info_reset(); void perf_ignore_this_loop(); void perf_info_check_loop_time(uint32_t time_in_micros); uint16_t perf_info_get_num_loops(); uint32_t perf_info_get_max_time(); uint32_t perf_info_get_min_time(); uint16_t perf_info_get_num_long_running(); uint32_t perf_info_get_num_dropped(); Vector3f pv_location_to_vector(const Location& loc); float pv_alt_above_origin(float alt_above_home_cm); float pv_alt_above_home(float alt_above_origin_cm); float pv_get_bearing_cd(const Vector3f &origin, const Vector3f &destination); float pv_get_horizontal_distance_cm(const Vector3f &origin, const Vector3f &destination); float pv_distance_to_home_cm(const Vector3f &destination); void default_dead_zones(); void init_rc_in(); void init_rc_out(); void enable_motor_output(); void read_radio(); void set_throttle_and_failsafe(uint16_t throttle_pwm); void set_throttle_zero_flag(int16_t throttle_control); void radio_passthrough_to_motors(); void init_barometer(bool full_calibration); void read_barometer(void); void init_rangefinder(void); void read_rangefinder(void); bool rangefinder_alt_ok(); void init_compass(); void init_optflow(); void update_optical_flow(void); void init_precland(); void update_precland(); void read_battery(void); void read_receiver_rssi(void); void epm_update(); void terrain_update(); void terrain_logging(); bool terrain_use(); void report_batt_monitor(); void report_frame(); void report_radio(); void report_ins(); void report_flight_modes(); void report_optflow(); void print_radio_values(); void print_switch(uint8_t p, uint8_t m, bool b); void print_accel_offsets_and_scaling(void); void print_gyro_offsets(void); void report_compass(); void print_blanks(int16_t num); void print_divider(void); void print_enabled(bool b); void report_version(); void read_control_switch(); bool check_if_auxsw_mode_used(uint8_t auxsw_mode_check); bool check_duplicate_auxsw(void); void reset_control_switch(); uint8_t read_3pos_switch(int16_t radio_in); void read_aux_switches(); void init_aux_switches(); void init_aux_switch_function(int8_t ch_option, uint8_t ch_flag); void do_aux_switch_function(int8_t ch_function, uint8_t ch_flag); void save_trim(); void auto_trim(); void init_ardupilot(); void startup_INS_ground(); bool calibrate_gyros(); bool position_ok(); bool ekf_position_ok(); bool optflow_position_ok(); void update_auto_armed(); void check_usb_mux(void); bool should_log(uint32_t mask); bool current_mode_has_user_takeoff(bool must_navigate); bool do_user_takeoff(float takeoff_alt_cm, bool must_navigate); void takeoff_timer_start(float alt_cm); void takeoff_stop(); void takeoff_get_climb_rates(float& pilot_climb_rate, float& takeoff_climb_rate); void print_hit_enter(); void tuning(); void gcs_send_text_fmt(MAV_SEVERITY severity, const char *fmt, ...); bool start_command(const AP_Mission::Mission_Command& cmd); bool verify_command(const AP_Mission::Mission_Command& cmd); bool verify_command_callback(const AP_Mission::Mission_Command& cmd); bool do_guided(const AP_Mission::Mission_Command& cmd); void do_takeoff(const AP_Mission::Mission_Command& cmd); void do_nav_wp(const AP_Mission::Mission_Command& cmd); void do_land(const AP_Mission::Mission_Command& cmd); void do_loiter_unlimited(const AP_Mission::Mission_Command& cmd); void do_circle(const AP_Mission::Mission_Command& cmd); void do_loiter_time(const AP_Mission::Mission_Command& cmd); void do_spline_wp(const AP_Mission::Mission_Command& cmd); #if NAV_GUIDED == ENABLED void do_nav_guided_enable(const AP_Mission::Mission_Command& cmd); void do_guided_limits(const AP_Mission::Mission_Command& cmd); #endif void do_nav_delay(const AP_Mission::Mission_Command& cmd); void do_wait_delay(const AP_Mission::Mission_Command& cmd); void do_within_distance(const AP_Mission::Mission_Command& cmd); void do_yaw(const AP_Mission::Mission_Command& cmd); void do_change_speed(const AP_Mission::Mission_Command& cmd); void do_set_home(const AP_Mission::Mission_Command& cmd); void do_roi(const AP_Mission::Mission_Command& cmd); void do_mount_control(const AP_Mission::Mission_Command& cmd); #if CAMERA == ENABLED void do_digicam_configure(const AP_Mission::Mission_Command& cmd); void do_digicam_control(const AP_Mission::Mission_Command& cmd); #endif #if PARACHUTE == ENABLED void do_parachute(const AP_Mission::Mission_Command& cmd); #endif #if EPM_ENABLED == ENABLED void do_gripper(const AP_Mission::Mission_Command& cmd); #endif bool verify_nav_wp(const AP_Mission::Mission_Command& cmd); bool verify_circle(const AP_Mission::Mission_Command& cmd); bool verify_spline_wp(const AP_Mission::Mission_Command& cmd); #if NAV_GUIDED == ENABLED bool verify_nav_guided_enable(const AP_Mission::Mission_Command& cmd); #endif bool verify_nav_delay(const AP_Mission::Mission_Command& cmd); void auto_spline_start(const Location_Class& destination, bool stopped_at_start, AC_WPNav::spline_segment_end_type seg_end_type, const Location_Class& next_destination); void print_flight_mode(AP_HAL::BetterStream *port, uint8_t mode); void log_init(void); void run_cli(AP_HAL::UARTDriver *port); void init_capabilities(void); void dataflash_periodic(void); void accel_cal_update(void); public: void mavlink_delay_cb(); void failsafe_check(); int8_t dump_log(uint8_t argc, const Menu::arg *argv); int8_t erase_logs(uint8_t argc, const Menu::arg *argv); int8_t select_logs(uint8_t argc, const Menu::arg *argv); bool print_log_menu(void); int8_t process_logs(uint8_t argc, const Menu::arg *argv); int8_t main_menu_help(uint8_t, const Menu::arg*); int8_t setup_mode(uint8_t argc, const Menu::arg *argv); int8_t setup_factory(uint8_t argc, const Menu::arg *argv); int8_t setup_set(uint8_t argc, const Menu::arg *argv); int8_t setup_show(uint8_t argc, const Menu::arg *argv); int8_t esc_calib(uint8_t argc, const Menu::arg *argv); int8_t test_mode(uint8_t argc, const Menu::arg *argv); int8_t test_baro(uint8_t argc, const Menu::arg *argv); int8_t test_compass(uint8_t argc, const Menu::arg *argv); int8_t test_ins(uint8_t argc, const Menu::arg *argv); int8_t test_optflow(uint8_t argc, const Menu::arg *argv); int8_t test_relay(uint8_t argc, const Menu::arg *argv); int8_t test_shell(uint8_t argc, const Menu::arg *argv); int8_t test_rangefinder(uint8_t argc, const Menu::arg *argv); int8_t reboot_board(uint8_t argc, const Menu::arg *argv); }; #define MENU_FUNC(func) FUNCTOR_BIND(&copter, &Copter::func, int8_t, uint8_t, const Menu::arg *) extern const AP_HAL::HAL& hal; extern Copter copter; using AP_HAL::millis; using AP_HAL::micros;