// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*- #ifndef _DEFINES_H #define _DEFINES_H #include // Just so that it's completely clear... #define ENABLED 1 #define DISABLED 0 // this avoids a very common config error #define ENABLE ENABLED #define DISABLE DISABLED // Flight modes // ------------ #define YAW_HOLD 0 // heading hold at heading in nav_yaw but allow input from pilot #define YAW_ACRO 1 // pilot controlled yaw using rate controller #define YAW_LOOK_AT_NEXT_WP 2 // point towards next waypoint (no pilot input accepted) #define YAW_LOOK_AT_LOCATION 3 // point towards a location held in yaw_look_at_WP (no pilot input accepted) #define YAW_LOOK_AT_HOME 4 // point towards home (no pilot input accepted) #define YAW_LOOK_AT_HEADING 5 // point towards a particular angle (not pilot input accepted) #define YAW_LOOK_AHEAD 6 // WARNING! CODE IN DEVELOPMENT NOT PROVEN #define YAW_TOY 7 // THOR This is the Yaw mode #define ROLL_PITCH_STABLE 0 #define ROLL_PITCH_ACRO 1 #define ROLL_PITCH_AUTO 2 #define ROLL_PITCH_STABLE_OF 3 #define ROLL_PITCH_TOY 4 // THOR This is the Roll and Pitch // mode #define THROTTLE_MANUAL 0 // manual throttle mode - pilot input goes directly to motors #define THROTTLE_MANUAL_TILT_COMPENSATED 1 // mostly manual throttle but with some tilt compensation #define THROTTLE_ACCELERATION 2 // pilot inputs the desired acceleration #define THROTTLE_RATE 3 // pilot inputs the desired climb rate. Note: this uses the unstabilized rate controller #define THROTTLE_STABILIZED_RATE 4 // pilot inputs the desired climb rate. Uses stabilized rate controller #define THROTTLE_DIRECT_ALT 5 // pilot inputs a desired altitude from 0 ~ 10 meters #define THROTTLE_HOLD 6 // alt hold plus pilot input of climb rate #define THROTTLE_AUTO 7 // auto pilot altitude controller with target altitude held in next_WP.alt #define THROTTLE_LAND 8 // landing throttle controller // active altitude sensor // ---------------------- #define SONAR 0 #define BARO 1 #define SONAR_SOURCE_ADC 1 #define SONAR_SOURCE_ANALOG_PIN 2 // CH 7 control #define CH7_PWM_TRIGGER 1800 // pwm value above which the channel 7 option will be invoked #define CH7_DO_NOTHING 0 #define CH7_SET_HOVER 1 // deprecated #define CH7_FLIP 2 #define CH7_SIMPLE_MODE 3 #define CH7_RTL 4 #define CH7_SAVE_TRIM 5 #define CH7_ADC_FILTER 6 // deprecated #define CH7_SAVE_WP 7 #define CH7_MULTI_MODE 8 // deprecated #define CH7_CAMERA_TRIGGER 9 // Frame types #define QUAD_FRAME 0 #define TRI_FRAME 1 #define HEXA_FRAME 2 #define Y6_FRAME 3 #define OCTA_FRAME 4 #define HELI_FRAME 5 #define OCTA_QUAD_FRAME 6 #define PLUS_FRAME 0 #define X_FRAME 1 #define V_FRAME 2 // LED output #define NORMAL_LEDS 0 #define SAVE_TRIM_LEDS 1 // Internal defines, don't edit and expect things to work // ------------------------------------------------------- #define TRUE 1 #define FALSE 0 #define ToRad(x) radians(x) // *pi/180 #define ToDeg(x) degrees(x) // *180/pi #define DEBUG 0 #define LOITER_RANGE 60 // for calculating power outside of loiter radius #define T6 1000000 #define T7 10000000 // GPS type codes - use the names, not the numbers #define GPS_PROTOCOL_NONE -1 #define GPS_PROTOCOL_NMEA 0 #define GPS_PROTOCOL_SIRF 1 #define GPS_PROTOCOL_UBLOX 2 #define GPS_PROTOCOL_IMU 3 #define GPS_PROTOCOL_MTK 4 #define GPS_PROTOCOL_HIL 5 #define GPS_PROTOCOL_MTK16 6 #define GPS_PROTOCOL_AUTO 7 // HIL enumerations #define HIL_MODE_DISABLED 0 #define HIL_MODE_ATTITUDE 1 #define HIL_MODE_SENSORS 2 // Altitude status definitions #define REACHED_ALT 0 #define DESCENDING 1 #define ASCENDING 2 // Auto Pilot modes // ---------------- #define STABILIZE 0 // hold level position #define ACRO 1 // rate control #define ALT_HOLD 2 // AUTO control #define AUTO 3 // AUTO control #define GUIDED 4 // AUTO control #define LOITER 5 // Hold a single location #define RTL 6 // AUTO control #define CIRCLE 7 // AUTO control #define POSITION 8 // AUTO control #define LAND 9 // AUTO control #define OF_LOITER 10 // Hold a single location using optical flow // sensor #define TOY_A 11 // THOR Enum for Toy mode #define TOY_M 12 // THOR Enum for Toy mode #define NUM_MODES 13 // CH_6 Tuning // ----------- #define CH6_NONE 0 // no tuning performed #define CH6_STABILIZE_KP 1 // stabilize roll/pitch angle controller's P term #define CH6_STABILIZE_KI 2 // stabilize roll/pitch angle controller's I term #define CH6_STABILIZE_KD 29 // stabilize roll/pitch angle controller's D term #define CH6_YAW_KP 3 // stabilize yaw heading controller's P term #define CH6_YAW_KI 24 // stabilize yaw heading controller's P term #define CH6_ACRO_KP 25 // acro controller's P term. converts pilot input to a desired roll, pitch or yaw rate #define CH6_RATE_KP 4 // body frame roll/pitch rate controller's P term #define CH6_RATE_KI 5 // body frame roll/pitch rate controller's I term #define CH6_RATE_KD 21 // body frame roll/pitch rate controller's D term #define CH6_YAW_RATE_KP 6 // body frame yaw rate controller's P term #define CH6_YAW_RATE_KD 26 // body frame yaw rate controller's D term #define CH6_THR_HOLD_KP 14 // altitude hold controller's P term (alt error to desired rate) #define CH6_THROTTLE_KP 7 // throttle rate controller's P term (desired rate to acceleration or motor output) #define CH6_THROTTLE_KI 33 // throttle rate controller's I term (desired rate to acceleration or motor output) #define CH6_THR_ACCEL_KP 34 // accel based throttle controller's P term #define CH6_THR_ACCEL_KI 35 // accel based throttle controller's I term #define CH6_THR_ACCEL_KD 36 // accel based throttle controller's D term #define CH6_TOP_BOTTOM_RATIO 8 // upper/lower motor ratio (not used) #define CH6_RELAY 9 // switch relay on if ch6 high, off if low #define CH6_TRAVERSE_SPEED 10 // maximum speed to next way point (0 to 10m/s) #define CH6_NAV_KP 11 // navigation rate controller's P term (speed error to tilt angle) #define CH6_NAV_KI 20 // navigation rate controller's I term (speed error to tilt angle) #define CH6_LOITER_KP 12 // loiter distance controller's P term (position error to speed) #define CH6_LOITER_KI 27 // loiter distance controller's I term (position error to speed) #define CH6_HELI_EXTERNAL_GYRO 13 // TradHeli specific external tail gyro gain #define CH6_OPTFLOW_KP 17 // optical flow loiter controller's P term (position error to tilt angle) #define CH6_OPTFLOW_KI 18 // optical flow loiter controller's I term (position error to tilt angle) #define CH6_OPTFLOW_KD 19 // optical flow loiter controller's D term (position error to tilt angle) #define CH6_LOITER_RATE_KP 22 // loiter rate controller's P term (speed error to tilt angle) #define CH6_LOITER_RATE_KI 28 // loiter rate controller's I term (speed error to tilt angle) #define CH6_LOITER_RATE_KD 23 // loiter rate controller's D term (speed error to tilt angle) #define CH6_AHRS_YAW_KP 30 // ahrs's compass effect on yaw angle (0 = very low, 1 = very high) #define CH6_AHRS_KP 31 // accelerometer effect on roll/pitch angle (0=low) #define CH6_INAV_TC 32 // inertial navigation baro/accel and gps/accel time constant (1.5 = strong baro/gps correction on accel estimatehas very strong does not correct accel estimate, 7 = very weak correction) // nav byte mask // ------------- #define NAV_LOCATION 1 #define NAV_ALTITUDE 2 #define NAV_DELAY 4 // Commands - Note that APM now uses a subset of the MAVLink protocol // commands. See enum MAV_CMD in the GCS_Mavlink library #define CMD_BLANK 0 // there is no command stored in the mem location // requested #define NO_COMMAND 0 // Navigation modes held in wp_control variable #define LOITER_MODE 1 #define WP_MODE 2 #define CIRCLE_MODE 3 #define NO_NAV_MODE 4 // Yaw override behaviours - used for setting yaw_override_behaviour #define YAW_OVERRIDE_BEHAVIOUR_AT_NEXT_WAYPOINT 0 // auto pilot takes back yaw control at next waypoint #define YAW_OVERRIDE_BEHAVIOUR_AT_MISSION_RESTART 1 // auto pilot tkaes back control only when mission is restarted // TOY mixing options #define TOY_LOOKUP_TABLE 0 #define TOY_LINEAR_MIXER 1 #define TOY_EXTERNAL_MIXER 2 // Waypoint options #define MASK_OPTIONS_RELATIVE_ALT 1 #define WP_OPTION_ALT_CHANGE 2 #define WP_OPTION_YAW 4 #define WP_OPTION_ALT_REQUIRED 8 #define WP_OPTION_RELATIVE 16 //#define WP_OPTION_ 32 //#define WP_OPTION_ 64 #define WP_OPTION_NEXT_CMD 128 // RTL state #define RTL_STATE_RETURNING_HOME 0 #define RTL_STATE_LOITERING_AT_HOME 1 #define RTL_STATE_FINAL_DESCENT 2 #define RTL_STATE_LAND 3 //repeating events #define RELAY_TOGGLE 5 // GCS Message ID's /// NOTE: to ensure we never block on sending MAVLink messages /// please keep each MSG_ to a single MAVLink message. If need be /// create new MSG_ IDs for additional messages on the same /// stream enum ap_message { MSG_HEARTBEAT, MSG_ATTITUDE, MSG_LOCATION, MSG_EXTENDED_STATUS1, MSG_EXTENDED_STATUS2, MSG_NAV_CONTROLLER_OUTPUT, MSG_CURRENT_WAYPOINT, MSG_VFR_HUD, MSG_RADIO_OUT, MSG_RADIO_IN, MSG_RAW_IMU1, MSG_RAW_IMU2, MSG_RAW_IMU3, MSG_GPS_STATUS, MSG_GPS_RAW, MSG_SERVO_OUT, MSG_NEXT_WAYPOINT, MSG_NEXT_PARAM, MSG_STATUSTEXT, MSG_LIMITS_STATUS, MSG_AHRS, MSG_SIMSTATE, MSG_HWSTATUS, MSG_RETRY_DEFERRED // this must be last }; enum gcs_severity { SEVERITY_LOW=1, SEVERITY_MEDIUM, SEVERITY_HIGH, SEVERITY_CRITICAL }; // Logging parameters #define TYPE_AIRSTART_MSG 0x00 #define TYPE_GROUNDSTART_MSG 0x01 #define LOG_ATTITUDE_MSG 0x01 #define LOG_GPS_MSG 0x02 #define LOG_MODE_MSG 0x03 #define LOG_CONTROL_TUNING_MSG 0x04 #define LOG_NAV_TUNING_MSG 0x05 #define LOG_PERFORMANCE_MSG 0x06 #define LOG_RAW_MSG 0x07 #define LOG_CMD_MSG 0x08 #define LOG_CURRENT_MSG 0x09 #define LOG_STARTUP_MSG 0x0A #define LOG_MOTORS_MSG 0x0B #define LOG_OPTFLOW_MSG 0x0C #define LOG_DATA_MSG 0x0D #define LOG_PID_MSG 0x0E #define LOG_ITERM_MSG 0x0F #define LOG_DMP_MSG 0x10 #define LOG_INAV_MSG 0x11 #define LOG_CAMERA_MSG 0x12 #define LOG_INDEX_MSG 0xF0 #define MAX_NUM_LOGS 50 #define MASK_LOG_ATTITUDE_FAST (1<<0) #define MASK_LOG_ATTITUDE_MED (1<<1) #define MASK_LOG_GPS (1<<2) #define MASK_LOG_PM (1<<3) #define MASK_LOG_CTUN (1<<4) #define MASK_LOG_NTUN (1<<5) #define MASK_LOG_MODE (1<<6) #define MASK_LOG_RAW (1<<7) #define MASK_LOG_CMD (1<<8) #define MASK_LOG_CUR (1<<9) #define MASK_LOG_MOTORS (1<<10) #define MASK_LOG_OPTFLOW (1<<11) #define MASK_LOG_PID (1<<12) #define MASK_LOG_ITERM (1<<13) #define MASK_LOG_INAV (1<<14) #define MASK_LOG_CAMERA (1<<15) // DATA - event logging #define DATA_MAVLINK_FLOAT 1 #define DATA_MAVLINK_INT32 2 #define DATA_MAVLINK_INT16 3 #define DATA_MAVLINK_INT8 4 #define DATA_FAST_LOOP 5 #define DATA_MED_LOOP 6 #define DATA_AP_STATE 7 #define DATA_SIMPLE_BEARING 8 #define DATA_INIT_SIMPLE_BEARING 9 #define DATA_ARMED 10 #define DATA_DISARMED 11 #define DATA_FAILSAFE_ON 12 #define DATA_FAILSAFE_OFF 13 #define DATA_LOW_BATTERY 14 #define DATA_AUTO_ARMED 15 #define DATA_TAKEOFF 16 #define DATA_DID_REACH_ALT 17 #define DATA_LAND_COMPLETE 18 #define DATA_LOST_GPS 19 #define DATA_LOST_COMPASS 20 #define DATA_BEGIN_FLIP 21 #define DATA_END_FLIP 22 #define DATA_EXIT_FLIP 23 #define DATA_FLIP_ABORTED 24 #define DATA_SET_HOME 25 #define DATA_SET_SIMPLE_ON 26 #define DATA_SET_SIMPLE_OFF 27 #define DATA_REACHED_ALT 28 #define DATA_ASCENDING 29 #define DATA_DESCENDING 30 #define DATA_RTL_REACHED_ALT 31 // battery monitoring macros #define BATTERY_VOLTAGE(x) (x*(g.input_voltage/1024.0))*g.volt_div_ratio #define CURRENT_AMPS(x) ((x*(g.input_voltage/1024.0))-CURR_AMPS_OFFSET)*g.curr_amp_per_volt /* ************************************************************** */ /* Expansion PIN's that people can use for various things. */ // AN0 - 7 are located at edge of IMU PCB "above" pressure sensor and // Expansion port // AN0 - 5 are also located next to voltage dividers and sliding SW2 switch // AN0 - 3 has 10kOhm resistor in serial, include 3.9kOhm to make it as // voltage divider // AN4 - 5 are direct GPIO pins from atmega1280 and they are the latest pins // next to SW2 switch // Look more ArduCopter Wiki for voltage dividers and other ports #define AN0 54 // resistor, vdiv use, divider 1 closest to relay #define AN1 55 // resistor, vdiv use, divider 2 #define AN2 56 // resistor, vdiv use, divider 3 #define AN3 57 // resistor, vdiv use, divider 4 closest to SW2 #define AN4 58 // direct GPIO pin, default as analog input, next to SW2 // switch #define AN5 59 // direct GPIO pin, default as analog input, next to SW2 // switch #define AN6 60 // direct GPIO pin, default as analog input, close to // Pressure sensor, Expansion Ports #define AN7 61 // direct GPIO pin, default as analog input, close to // Pressure sensor, Expansion Ports // AN8 - 15 are located at edge of IMU PCB "above" pressure sensor and // Expansion port // AN8 - 15 PINs are not connected anywhere, they are located as last 8 pins // on edge of the board above Expansion Ports // even pins (8,10,12,14) are at edge of board, Odd pins (9,11,13,15) are on // inner row #define AN8 62 // NC #define AN9 63 // NC #define AN10 64 // NC #define AN11 65 // NC #define AN12 66 // NC #define AN13 67 // NC #define AN14 68 // NC #define AN15 69 // NC #define RELAY_PIN 47 #define PIEZO_PIN AN5 //Last pin on the back ADC connector // RADIANS #define RADX100 0.000174532925 #define DEGX100 5729.57795 // EEPROM addresses #define EEPROM_MAX_ADDR 4096 // parameters get the first 1536 bytes of EEPROM, remainder is for waypoints #define WP_START_BYTE 0x600 // where in memory home WP is stored + all other // WP #define WP_SIZE 15 // fence points are stored at the end of the EEPROM #define MAX_FENCEPOINTS 6 #define FENCE_WP_SIZE sizeof(Vector2l) #define FENCE_START_BYTE (EEPROM_MAX_ADDR-(MAX_FENCEPOINTS*FENCE_WP_SIZE)) #define MAX_WAYPOINTS ((FENCE_START_BYTE - WP_START_BYTE) / WP_SIZE) - 1 // - // 1 // to // be // safe // mark a function as not to be inlined #define NOINLINE __attribute__((noinline)) // IMU selection #define CONFIG_IMU_OILPAN 1 #define CONFIG_IMU_MPU6000 2 #define CONFIG_IMU_SITL 3 #define AP_BARO_BMP085 1 #define AP_BARO_MS5611 2 #endif // _DEFINES_H