#include "Copter.h" // Code to detect a crash main ArduCopter code #define LAND_CHECK_ANGLE_ERROR_DEG 30.0f // maximum angle error to be considered landing #define LAND_CHECK_LARGE_ANGLE_CD 1500.0f // maximum angle target to be considered landing #define LAND_CHECK_ACCEL_MOVING 3.0f // maximum acceleration after subtracting gravity // counter to verify landings static uint32_t land_detector_count = 0; // run land and crash detectors // called at MAIN_LOOP_RATE void Copter::update_land_and_crash_detectors() { // update 1hz filtered acceleration Vector3f accel_ef = ahrs.get_accel_ef_blended(); accel_ef.z += GRAVITY_MSS; land_accel_ef_filter.apply(accel_ef, MAIN_LOOP_SECONDS); update_land_detector(); #if PARACHUTE == ENABLED // check parachute parachute_check(); #endif crash_check(); } // update_land_detector - checks if we have landed and updates the ap.land_complete flag // called at MAIN_LOOP_RATE void Copter::update_land_detector() { // land detector can not use the following sensors because they are unreliable during landing // barometer altitude : ground effect can cause errors larger than 4m // EKF vertical velocity or altitude : poor barometer and large acceleration from ground impact // earth frame angle or angle error : landing on an uneven surface will force the airframe to match the ground angle // gyro output : on uneven surface the airframe may rock back an forth after landing // range finder : tend to be problematic at very short distances // input throttle : in slow land the input throttle may be only slightly less than hover if (!motors->armed()) { // if disarmed, always landed. set_land_complete(true); } else if (ap.land_complete) { #if FRAME_CONFIG == HELI_FRAME // if rotor speed and collective pitch are high then clear landing flag if (motors->get_throttle() > get_non_takeoff_throttle() && !motors->limit.throttle_lower && motors->rotor_runup_complete()) { #else // if throttle output is high then clear landing flag if (motors->get_throttle() > get_non_takeoff_throttle()) { #endif set_land_complete(false); } } else { #if FRAME_CONFIG == HELI_FRAME // check that collective pitch is on lower limit (should be constrained by LAND_COL_MIN) bool motor_at_lower_limit = motors->limit.throttle_lower; #else // check that the average throttle output is near minimum (less than 12.5% hover throttle) bool motor_at_lower_limit = motors->limit.throttle_lower && attitude_control->is_throttle_mix_min(); #endif // check that the airframe is not accelerating (not falling or breaking after fast forward flight) bool accel_stationary = (land_accel_ef_filter.get().length() <= LAND_DETECTOR_ACCEL_MAX); // check that vertical speed is within 1m/s of zero bool descent_rate_low = fabsf(inertial_nav.get_velocity_z()) < 100; // if we have a healthy rangefinder only allow landing detection below 2 meters bool rangefinder_check = (!rangefinder_alt_ok() || rangefinder_state.alt_cm_filt.get() < LAND_RANGEFINDER_MIN_ALT_CM); if (motor_at_lower_limit && accel_stationary && descent_rate_low && rangefinder_check) { // landed criteria met - increment the counter and check if we've triggered if( land_detector_count < ((float)LAND_DETECTOR_TRIGGER_SEC)*scheduler.get_loop_rate_hz()) { land_detector_count++; } else { set_land_complete(true); } } else { // we've sensed movement up or down so reset land_detector land_detector_count = 0; } } set_land_complete_maybe(ap.land_complete || (land_detector_count >= LAND_DETECTOR_MAYBE_TRIGGER_SEC*scheduler.get_loop_rate_hz())); } // set land_complete flag and disarm motors if disarm-on-land is configured void Copter::set_land_complete(bool b) { // if no change, exit immediately if( ap.land_complete == b ) return; land_detector_count = 0; if(b){ Log_Write_Event(DATA_LAND_COMPLETE); } else { Log_Write_Event(DATA_NOT_LANDED); } ap.land_complete = b; g2.stats.set_flying(!b); // trigger disarm-on-land if configured bool disarm_on_land_configured = (g.throttle_behavior & THR_BEHAVE_DISARM_ON_LAND_DETECT) != 0; bool mode_disarms_on_land = mode_allows_arming(control_mode,false) && !mode_has_manual_throttle(control_mode); if (ap.land_complete && motors->armed() && disarm_on_land_configured && mode_disarms_on_land) { init_disarm_motors(); } } // set land complete maybe flag void Copter::set_land_complete_maybe(bool b) { // if no change, exit immediately if (ap.land_complete_maybe == b) return; if (b) { Log_Write_Event(DATA_LAND_COMPLETE_MAYBE); } ap.land_complete_maybe = b; } // update_throttle_thr_mix - sets motors throttle_low_comp value depending upon vehicle state // low values favour pilot/autopilot throttle over attitude control, high values favour attitude control over throttle // has no effect when throttle is above hover throttle void Copter::update_throttle_thr_mix() { #if FRAME_CONFIG != HELI_FRAME // if disarmed or landed prioritise throttle if(!motors->armed() || ap.land_complete) { attitude_control->set_throttle_mix_min(); return; } if (mode_has_manual_throttle(control_mode)) { // manual throttle if(channel_throttle->get_control_in() <= 0) { attitude_control->set_throttle_mix_min(); } else { attitude_control->set_throttle_mix_man(); } } else { // autopilot controlled throttle // check for aggressive flight requests - requested roll or pitch angle below 15 degrees const Vector3f angle_target = attitude_control->get_att_target_euler_cd(); bool large_angle_request = (norm(angle_target.x, angle_target.y) > LAND_CHECK_LARGE_ANGLE_CD); // check for large external disturbance - angle error over 30 degrees const float angle_error = attitude_control->get_att_error_angle_deg(); bool large_angle_error = (angle_error > LAND_CHECK_ANGLE_ERROR_DEG); // check for large acceleration - falling or high turbulence Vector3f accel_ef = ahrs.get_accel_ef_blended(); accel_ef.z += GRAVITY_MSS; bool accel_moving = (accel_ef.length() > LAND_CHECK_ACCEL_MOVING); // check for requested decent bool descent_not_demanded = pos_control->get_desired_velocity().z >= 0.0f; if ( large_angle_request || large_angle_error || accel_moving || descent_not_demanded) { attitude_control->set_throttle_mix_max(); } else { attitude_control->set_throttle_mix_min(); } } #endif }