// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*- // update_navigation - checks for new GPS updates and invokes navigation routines // called at 50hz static void update_navigation() { static uint32_t nav_last_update = 0; // the system time of the last time nav was run update bool pos_updated = false; bool log_output = false; #if INERTIAL_NAV_XY == ENABLED static uint8_t nav_counter = 0; // used to slow down the navigation to 10hz // check for inertial nav updates if( inertial_nav.position_ok() ) { nav_counter++; if( nav_counter >= 5) { nav_counter = 0; // calculate time since nav controllers last ran dTnav = (float)(millis() - nav_last_update)/ 1000.0f; nav_last_update = millis(); // prevent runnup in dTnav value dTnav = min(dTnav, 1.0f); // signal to run nav controllers pos_updated = true; // signal to create log entry log_output = true; } } #else static uint32_t nav_last_gps_time = 0; // the time according to the gps // check for new gps data if( g_gps->fix && g_gps->time != nav_last_gps_time ) { // used to calculate speed in X and Y, iterms // ------------------------------------------ dTnav = (float)(millis() - nav_last_update)/ 1000.0f; nav_last_update = millis(); // prevent runup from bad GPS dTnav = min(dTnav, 1.0f); // save GPS time nav_last_gps_time = g_gps->time; // signal to run nav controllers pos_updated = true; // signal to create log entry log_output = true; } #endif // setup to calculate new navigation values and run controllers if // we've received a position update if( pos_updated ) { nav_updates.need_velpos = 1; nav_updates.need_dist_bearing = 1; nav_updates.need_nav_controllers = 1; nav_updates.need_nav_pitch_roll = 1; // update log if (log_output && (g.log_bitmask & MASK_LOG_NTUN) && motors.armed()) { Log_Write_Nav_Tuning(); } } // reduce nav outputs to zero if we have not seen a position update in 2 seconds if( millis() - nav_last_update > 2000 ) { // after 12 reads we guess we may have lost GPS signal, stop navigating // we have lost GPS signal for a moment. Reduce our error to avoid flyaways auto_roll >>= 1; auto_pitch >>= 1; } } /* run navigation updates from nav_updates. Only run one at a time to prevent too much cpu usage hurting the main loop */ static void run_nav_updates(void) { if (nav_updates.need_velpos) { calc_velocity_and_position(); nav_updates.need_velpos = 0; } else if (nav_updates.need_dist_bearing) { calc_distance_and_bearing(); nav_updates.need_dist_bearing = 0; } else if (nav_updates.need_nav_controllers) { run_autopilot(); update_nav_mode(); nav_updates.need_nav_controllers = 0; } else if (nav_updates.need_nav_pitch_roll) { calc_nav_pitch_roll(); nav_updates.need_nav_pitch_roll = 0; } } //******************************************************************************************************* // calc_velocity_and_filtered_position - velocity in lon and lat directions calculated from GPS position // and accelerometer data // lon_speed expressed in cm/s. positive numbers mean moving east // lat_speed expressed in cm/s. positive numbers when moving north // Note: we use gps locations directly to calculate velocity instead of asking gps for velocity because // this is more accurate below 1.5m/s // Note: even though the positions are projected using a lead filter, the velocities are calculated // from the unaltered gps locations. We do not want noise from our lead filter affecting velocity //******************************************************************************************************* static void calc_velocity_and_position(){ #if INERTIAL_NAV_XY == ENABLED if( inertial_nav.position_ok() ) { // pull velocity from interial nav library lon_speed = inertial_nav.get_longitude_velocity(); lat_speed = inertial_nav.get_latitude_velocity(); // pull position from interial nav library current_loc.lng = inertial_nav.get_longitude(); current_loc.lat = inertial_nav.get_latitude(); } #else static int32_t last_gps_longitude = 0; static int32_t last_gps_latitude = 0; // initialise last_longitude and last_latitude if( last_gps_longitude == 0 && last_gps_latitude == 0 ) { last_gps_longitude = g_gps->longitude; last_gps_latitude = g_gps->latitude; } // this speed is ~ in cm because we are using 10^7 numbers from GPS float tmp = 1.0f/dTnav; // calculate velocity lon_speed = (float)(g_gps->longitude - last_gps_longitude) * scaleLongDown * tmp; lat_speed = (float)(g_gps->latitude - last_gps_latitude) * tmp; // calculate position from gps + expected travel during gps_lag current_loc.lng = xLeadFilter.get_position(g_gps->longitude, lon_speed, g_gps->get_lag()); current_loc.lat = yLeadFilter.get_position(g_gps->latitude, lat_speed, g_gps->get_lag()); // store gps lat and lon values for next iteration last_gps_longitude = g_gps->longitude; last_gps_latitude = g_gps->latitude; #endif } //**************************************************************** // Function that will calculate the desired direction to fly and distance //**************************************************************** static void calc_distance_and_bearing() { // waypoint distance from plane in cm // --------------------------------------- wp_distance = get_distance_cm(¤t_loc, &next_WP); home_distance = get_distance_cm(¤t_loc, &home); // wp_bearing is bearing to next waypoint // -------------------------------------------- wp_bearing = get_bearing_cd(¤t_loc, &next_WP); home_bearing = get_bearing_cd(¤t_loc, &home); // update super simple bearing (if required) because it relies on home_bearing update_super_simple_beading(); // bearing to target (used when yaw_mode = YAW_LOOK_AT_LOCATION) yaw_look_at_WP_bearing = get_bearing_cd(¤t_loc, &yaw_look_at_WP); } static void calc_location_error(struct Location *next_loc) { /* * Becuase we are using lat and lon to do our distance errors here's a quick chart: * 100 = 1m * 1000 = 11m = 36 feet * 1800 = 19.80m = 60 feet * 3000 = 33m * 10000 = 111m */ // X Error long_error = (float)(next_loc->lng - current_loc.lng) * scaleLongDown; // 500 - 0 = 500 Go East // Y Error lat_error = next_loc->lat - current_loc.lat; // 500 - 0 = 500 Go North } // run_autopilot - highest level call to process mission commands static void run_autopilot() { switch( control_mode ) { case AUTO: // majority of command logic is in commands_logic.pde verify_commands(); break; case GUIDED: // switch to loiter once we've reached the target location and altitude if(verify_nav_wp()) { set_nav_mode(NAV_LOITER); } case RTL: verify_RTL(); break; } } // set_nav_mode - update nav mode and initialise any variables as required static bool set_nav_mode(uint8_t new_nav_mode) { // boolean to ensure proper initialisation of nav modes bool nav_initialised = false; // return immediately if no change if( new_nav_mode == nav_mode ) { return true; } switch( new_nav_mode ) { case NAV_NONE: nav_initialised = true; break; case NAV_CIRCLE: // start circling around current location set_next_WP(¤t_loc); circle_WP = next_WP; circle_angle = 0; nav_initialised = true; break; case NAV_LOITER: // set target to current position next_WP.lat = current_loc.lat; next_WP.lng = current_loc.lng; nav_initialised = true; break; case NAV_WP: nav_initialised = true; break; case NAV_LOITER_INAV: loiter_set_target(inertial_nav.get_latitude_diff(), inertial_nav.get_longitude_diff()); nav_initialised = true; break; } // if initialisation has been successful update the yaw mode if( nav_initialised ) { nav_mode = new_nav_mode; } // return success or failure return nav_initialised; } // update_nav_mode - run navigation controller based on nav_mode static void update_nav_mode() { int16_t loiter_delta; int16_t speed; switch( nav_mode ) { case NAV_NONE: // do nothing break; case NAV_CIRCLE: // check if we have missed the WP loiter_delta = (wp_bearing - old_wp_bearing)/100; // reset the old value old_wp_bearing = wp_bearing; // wrap values if (loiter_delta > 180) loiter_delta -= 360; if (loiter_delta < -180) loiter_delta += 360; // sum the angle around the WP loiter_sum += loiter_delta; circle_angle += (circle_rate * dTnav); //1 degree = 0.0174532925 radians // wrap if (circle_angle > 6.28318531f) circle_angle -= 6.28318531f; next_WP.lng = circle_WP.lng + (g.circle_radius * 100 * cosf(1.57f - circle_angle) * scaleLongUp); next_WP.lat = circle_WP.lat + (g.circle_radius * 100 * sinf(1.57f - circle_angle)); // use error as the desired rate towards the target // nav_lon, nav_lat is calculated // if the target location is >4m use waypoint controller if(wp_distance > 400) { calc_nav_rate(get_desired_speed(g.waypoint_speed_max)); }else{ // calc the lat and long error to the target calc_location_error(&next_WP); // call loiter controller calc_loiter(long_error, lat_error); } break; case NAV_LOITER: // check if user is overriding the loiter controller if((abs(g.rc_2.control_in) + abs(g.rc_1.control_in)) > 500) { if(wp_distance > 500){ ap.loiter_override = true; } } // check if user has release sticks if(ap.loiter_override) { if(g.rc_2.control_in == 0 && g.rc_1.control_in == 0) { ap.loiter_override = false; // reset LOITER to current position next_WP.lat = current_loc.lat; next_WP.lng = current_loc.lng; } // We bring copy over our Iterms for wind control, but we don't navigate nav_lon = g.pid_loiter_rate_lon.get_integrator(); nav_lat = g.pid_loiter_rate_lon.get_integrator(); nav_lon = constrain(nav_lon, -2000, 2000); nav_lat = constrain(nav_lat, -2000, 2000); }else{ // calc error to target calc_location_error(&next_WP); // use error as the desired rate towards the target calc_loiter(long_error, lat_error); } break; case NAV_WP: // calc position error to target calc_location_error(&next_WP); // calc speed to target speed = get_desired_speed(g.waypoint_speed_max); // use error as the desired rate towards the target calc_nav_rate(speed); break; case NAV_LOITER_INAV: get_loiter_pos_lat_lon(loiter_lat_from_home_cm, loiter_lon_from_home_cm, 0.1f); break; } /* // To-Do: check that we haven't broken toy mode case TOY_A: case TOY_M: set_nav_mode(NAV_NONE); update_nav_wp(); break; } */ } static bool check_missed_wp() { int32_t temp; temp = wp_bearing - original_wp_bearing; temp = wrap_180(temp); return (labs(temp) > 9000); // we passed the waypoint by 100 degrees } //////////////////////////////////////////////////////////////// // Loiter controller (based on GPS position) //////////////////////////////////////////////////////////////// #define NAV_ERR_MAX 600 #define NAV_RATE_ERR_MAX 250 static void calc_loiter(int16_t x_error, int16_t y_error) { int32_t p,i,d; // used to capture pid values for logging int32_t output; int32_t x_target_speed, y_target_speed; // East / West x_target_speed = g.pi_loiter_lon.get_p(x_error); // calculate desired speed from lon error #if LOGGING_ENABLED == ENABLED // log output if PID logging is on and we are tuning the yaw if( g.log_bitmask & MASK_LOG_PID && (g.radio_tuning == CH6_LOITER_KP || g.radio_tuning == CH6_LOITER_KI) ) { Log_Write_PID(CH6_LOITER_KP, x_error, x_target_speed, 0, 0, x_target_speed, tuning_value); } #endif // calculate rate error x_rate_error = x_target_speed - lon_speed; // calc the speed error p = g.pid_loiter_rate_lon.get_p(x_rate_error); i = g.pid_loiter_rate_lon.get_i(x_rate_error + x_error, dTnav); d = g.pid_loiter_rate_lon.get_d(x_error, dTnav); d = constrain(d, -2000, 2000); // get rid of noise if(abs(lon_speed) < 50) { d = 0; } output = p + i + d; nav_lon = constrain(output, -4500, 4500); // constrain max angle to 45 degrees #if LOGGING_ENABLED == ENABLED // log output if PID logging is on and we are tuning the yaw if( g.log_bitmask & MASK_LOG_PID && (g.radio_tuning == CH6_LOITER_RATE_KP || g.radio_tuning == CH6_LOITER_RATE_KI || g.radio_tuning == CH6_LOITER_RATE_KD) ) { Log_Write_PID(CH6_LOITER_RATE_KP, x_rate_error, p, i, d, nav_lon, tuning_value); } #endif // North / South y_target_speed = g.pi_loiter_lat.get_p(y_error); // calculate desired speed from lat error #if LOGGING_ENABLED == ENABLED // log output if PID logging is on and we are tuning the yaw if( g.log_bitmask & MASK_LOG_PID && (g.radio_tuning == CH6_LOITER_KP || g.radio_tuning == CH6_LOITER_KI) ) { Log_Write_PID(CH6_LOITER_KP+100, y_error, y_target_speed, 0, 0, y_target_speed, tuning_value); } #endif // calculate rate error y_rate_error = y_target_speed - lat_speed; // calc the speed error p = g.pid_loiter_rate_lat.get_p(y_rate_error); i = g.pid_loiter_rate_lat.get_i(y_rate_error + y_error, dTnav); d = g.pid_loiter_rate_lat.get_d(y_error, dTnav); d = constrain(d, -2000, 2000); // get rid of noise if(abs(lat_speed) < 50) { d = 0; } output = p + i + d; nav_lat = constrain(output, -4500, 4500); // constrain max angle to 45 degrees #if LOGGING_ENABLED == ENABLED // log output if PID logging is on and we are tuning the yaw if( g.log_bitmask & MASK_LOG_PID && (g.radio_tuning == CH6_LOITER_RATE_KP || g.radio_tuning == CH6_LOITER_RATE_KI || g.radio_tuning == CH6_LOITER_RATE_KD) ) { Log_Write_PID(CH6_LOITER_RATE_KP+100, y_rate_error, p, i, d, nav_lat, tuning_value); } #endif // copy over I term to Nav_Rate g.pid_nav_lon.set_integrator(g.pid_loiter_rate_lon.get_integrator()); g.pid_nav_lat.set_integrator(g.pid_loiter_rate_lat.get_integrator()); } /////////////////////////////////////////////////////////// // Waypoint controller (based on GPS position) /////////////////////////////////////////////////////////// static void calc_nav_rate(int16_t max_speed) { float temp, temp_x, temp_y; // push us towards the original track update_crosstrack(); int16_t cross_speed = crosstrack_error * -g.crosstrack_gain; // scale down crosstrack_error in cm cross_speed = constrain(cross_speed, -150, 150); // rotate by 90 to deal with trig functions temp = (9000l - wp_bearing) * RADX100; temp_x = cosf(temp); temp_y = sinf(temp); // rotate desired spped vector: int32_t x_target_speed = max_speed * temp_x - cross_speed * temp_y; int32_t y_target_speed = cross_speed * temp_x + max_speed * temp_y; // East / West // calculate rate error x_rate_error = x_target_speed - lon_speed; x_rate_error = constrain(x_rate_error, -500, 500); nav_lon = g.pid_nav_lon.get_pid(x_rate_error, dTnav); int32_t tilt = (x_target_speed * x_target_speed * (int32_t)g.tilt_comp) / 10000; if(x_target_speed < 0) tilt = -tilt; nav_lon += tilt; // North / South // calculate rate error y_rate_error = y_target_speed - lat_speed; y_rate_error = constrain(y_rate_error, -500, 500); // added a rate error limit to keep pitching down to a minimum nav_lat = g.pid_nav_lat.get_pid(y_rate_error, dTnav); tilt = (y_target_speed * y_target_speed * (int32_t)g.tilt_comp) / 10000; if(y_target_speed < 0) tilt = -tilt; nav_lat += tilt; // copy over I term to Loiter_Rate g.pid_loiter_rate_lon.set_integrator(g.pid_nav_lon.get_integrator()); g.pid_loiter_rate_lat.set_integrator(g.pid_nav_lat.get_integrator()); } // this calculation rotates our World frame of reference to the copter's frame of reference // We use the DCM's matrix to precalculate these trig values at 50hz static void calc_nav_pitch_roll() { // To-Do: remove this hack dependent upon nav_mode if( nav_mode != NAV_LOITER_INAV ) { // rotate the vector auto_roll = (float)nav_lon * sin_yaw_y - (float)nav_lat * cos_yaw_x; auto_pitch = (float)nav_lon * cos_yaw_x + (float)nav_lat * sin_yaw_y; // flip pitch because forward is negative auto_pitch = -auto_pitch; // constrain maximum roll and pitch angles to 45 degrees auto_roll = constrain(auto_roll, -4500, 4500); auto_pitch = constrain(auto_pitch, -4500, 4500); } } static int16_t get_desired_speed(int16_t max_speed) { /* Based on Equation by Bill Premerlani & Robert Lefebvre (sq(V2)-sq(V1))/2 = A(X2-X1) derives to: V1 = sqrt(sq(V2) - 2*A*(X2-X1)) */ if(ap.fast_corner) { // don't slow down }else{ if(wp_distance < 20000){ // limit the size of numbers we're dealing with to avoid overflow // go slower int32_t temp = 2 * 100 * (int32_t)(wp_distance - g.waypoint_radius * 100); int32_t s_min = WAYPOINT_SPEED_MIN; temp += s_min * s_min; if( temp < 0 ) temp = 0; // check to ensure we don't try to take the sqrt of a negative number max_speed = sqrtf((float)temp); max_speed = min(max_speed, g.waypoint_speed_max); } } max_speed = min(max_speed, max_speed_old + (100 * dTnav));// limit going faster max_speed = max(max_speed, WAYPOINT_SPEED_MIN); // don't go too slow max_speed_old = max_speed; return max_speed; } static void reset_desired_speed() { max_speed_old = 0; } static void update_crosstrack(void) { // Crosstrack Error // ---------------- if (wp_distance >= (unsigned long)max((g.crosstrack_min_distance * 100),0) && abs(wrap_180(wp_bearing - original_wp_bearing)) < 4500) { float temp = (wp_bearing - original_wp_bearing) * RADX100; crosstrack_error = sinf(temp) * wp_distance; // Meters we are off track line }else{ // fade out crosstrack crosstrack_error >>= 1; } } static void force_new_altitude(int32_t new_alt) { next_WP.alt = new_alt; set_alt_change(REACHED_ALT); } static void set_new_altitude(int32_t new_alt) { // if no change exit immediately if(new_alt == next_WP.alt) { return; } // update new target altitude next_WP.alt = new_alt; if(next_WP.alt > (current_loc.alt + 80)) { // we are below, going up set_alt_change(ASCENDING); }else if(next_WP.alt < (current_loc.alt - 80)) { // we are above, going down set_alt_change(DESCENDING); }else{ // No Change set_alt_change(REACHED_ALT); } } static void verify_altitude() { if(alt_change_flag == ASCENDING) { // we are below, going up if(current_loc.alt > next_WP.alt - 50) { set_alt_change(REACHED_ALT); } }else if (alt_change_flag == DESCENDING) { // we are above, going down if(current_loc.alt <= next_WP.alt + 50){ set_alt_change(REACHED_ALT); } } } // Keeps old data out of our calculation / logs static void reset_nav_params(void) { // always start Circle mode at same angle circle_angle = 0; // We must be heading to a new WP, so XTrack must be 0 crosstrack_error = 0; // Will be set by new command wp_bearing = 0; // Will be set by new command wp_distance = 0; // Will be set by new command, used by loiter long_error = 0; lat_error = 0; nav_lon = 0; nav_lat = 0; nav_roll = 0; nav_pitch = 0; auto_roll = 0; auto_pitch = 0; } static int32_t wrap_360(int32_t error) { if (error > 36000) error -= 36000; if (error < 0) error += 36000; return error; } static int32_t wrap_180(int32_t error) { if (error > 18000) error -= 36000; if (error < -18000) error += 36000; return error; } // get_yaw_slew - reduces rate of change of yaw to a maximum // assumes it is called at 100hz so centi-degrees and update rate cancel each other out static int32_t get_yaw_slew(int32_t current_yaw, int32_t desired_yaw, int16_t deg_per_sec) { return wrap_360(current_yaw + constrain(wrap_180(desired_yaw - current_yaw), -deg_per_sec, deg_per_sec)); } //////////////////////////////////////////////////// // Loiter controller using inertial nav //////////////////////////////////////////////////// // get_loiter_accel - loiter acceration controllers with desired accelerations provided in forward/right directions in cm/s/s static void get_loiter_accel(int16_t accel_req_forward, int16_t accel_req_right) { static float z_accel_meas = 0; // The acceleration error in cm. static float accel_forward = 0; // The acceleration error in cm. static float accel_right = 0; // The acceleration error in cm. z_accel_meas = -AP_INTERTIALNAV_GRAVITY * 100; // calculate accel and filter with fc = 2 Hz // 100hz sample rate, 2hz filter, alpha = 0.11164f // 20hz sample rate, 2hz filter, alpha = 0.38587f // 10hz sample rate, 2hz filter, alpha = 0.55686f accel_forward = accel_forward + 0.55686f * (accel_req_forward - accel_forward); accel_right = accel_right + 0.55686f * (accel_req_right - accel_right); // update angle targets that will be passed to stabilize controller auto_roll = constrain((accel_right/(-z_accel_meas))*(18000/M_PI), -4500, 4500); auto_pitch = constrain((-accel_forward/(-z_accel_meas*cos_roll_x))*(18000/M_PI), -4500, 4500); } // get_loiter_accel_lat_lon - loiter acceration controller with desired accelerations provided in lat/lon directions in cm/s/s static void get_loiter_accel_lat_lon(int16_t accel_lat, int16_t accel_lon) { float accel_forward; float accel_right; accel_forward = accel_lat*cos_yaw + accel_lon*sin_yaw; accel_right = -accel_lat*sin_yaw + accel_lon*cos_yaw; get_loiter_accel(accel_forward, accel_right); } // get_loiter_vel_lat_lon - loiter velocity controller with desired velocity provided in lat/lon directions in cm/s #define MAX_LOITER_VEL_ACCEL 400 // should be 1.5 times larger than MAX_LOITER_POS_ACCEL static void get_loiter_vel_lat_lon(int16_t vel_lat, int16_t vel_lon, float dt) { static float speed_error_lat = 0; // The velocity in cm/s. static float speed_error_lon = 0; // The velocity in cm/s. float speed_lat = inertial_nav.get_latitude_velocity(); float speed_lon = inertial_nav.get_longitude_velocity(); int32_t accel_lat; int32_t accel_lon; int32_t accel_total; int16_t lat_p,lat_i,lat_d; int16_t lon_p,lon_i,lon_d; // calculate vel error and Filter with fc = 2 Hz // 100hz sample rate, 2hz filter, alpha = 0.11164f // 20hz sample rate, 2hz filter, alpha = 0.38587f // 10hz sample rate, 2hz filter, alpha = 0.55686f speed_error_lat = speed_error_lat + 0.55686f * ((vel_lat - speed_lat) - speed_error_lat); speed_error_lon = speed_error_lon + 0.55686f * ((vel_lon - speed_lon) - speed_error_lon); lat_p = g.pid_loiter_rate_lat.get_p(speed_error_lat); lat_i = g.pid_loiter_rate_lat.get_i(speed_error_lat, dt); lat_d = g.pid_loiter_rate_lat.get_d(speed_error_lat, dt); lon_p = g.pid_loiter_rate_lon.get_p(speed_error_lon); lon_i = g.pid_loiter_rate_lon.get_i(speed_error_lon, dt); lon_d = g.pid_loiter_rate_lon.get_d(speed_error_lon, dt); accel_lat = (lat_p+lat_i+lat_d); accel_lon = (lon_p+lon_i+lon_d); accel_total = safe_sqrt(accel_lat*accel_lat + accel_lon*accel_lon); if( accel_total > MAX_LOITER_VEL_ACCEL ) { accel_lat = MAX_LOITER_VEL_ACCEL * accel_lat/accel_total; accel_lon = MAX_LOITER_VEL_ACCEL * accel_lon/accel_total; } get_loiter_accel_lat_lon(accel_lat, accel_lon); } // get_loiter_pos_lat_lon - loiter position controller with desired position provided as distance from home in lat/lon directions in cm #define MAX_LOITER_POS_VELOCITY 750 // should be 1.5 ~ 2.0 times the pilot input's max velocity #define MAX_LOITER_POS_ACCEL 250 static void get_loiter_pos_lat_lon(int32_t target_lat, int32_t target_lon, float dt) { static float dist_error_lat; int32_t desired_vel_lat; static float dist_error_lon; int32_t desired_vel_lon; int32_t dist_error_total; int16_t vel_sqrt; int32_t vel_total; int16_t linear_distance; // the distace we swap between linear and sqrt. // calculate distance error and Filter with fc = 2 Hz // 100hz sample rate, 2hz filter, alpha = 0.11164f // 20hz sample rate, 2hz filter, alpha = 0.38587f // 10hz sample rate, 2hz filter, alpha = 0.55686f dist_error_lat = dist_error_lat + 0.55686f * ((target_lat - inertial_nav.get_latitude_diff()) - dist_error_lat); dist_error_lon = dist_error_lon + 0.55686f * ((target_lon - inertial_nav.get_longitude_diff()) - dist_error_lon); linear_distance = MAX_LOITER_POS_ACCEL/(2*g.pi_loiter_lat.kP()*g.pi_loiter_lat.kP()); dist_error_total = safe_sqrt(dist_error_lat*dist_error_lat + dist_error_lon*dist_error_lon); if( dist_error_total > 2*linear_distance ) { vel_sqrt = constrain(safe_sqrt(2*MAX_LOITER_POS_ACCEL*(dist_error_total-linear_distance)),0,1000); desired_vel_lat = vel_sqrt * dist_error_lat/dist_error_total; desired_vel_lon = vel_sqrt * dist_error_lon/dist_error_total; }else{ desired_vel_lat = g.pi_loiter_lat.get_p(dist_error_lat); desired_vel_lon = g.pi_loiter_lon.get_p(dist_error_lon); } vel_total = safe_sqrt(desired_vel_lat*desired_vel_lat + desired_vel_lon*desired_vel_lon); if( vel_total > MAX_LOITER_POS_VELOCITY ) { desired_vel_lat = MAX_LOITER_POS_VELOCITY * desired_vel_lat/vel_total; desired_vel_lon = MAX_LOITER_POS_VELOCITY * desired_vel_lon/vel_total; } get_loiter_vel_lat_lon(desired_vel_lat, desired_vel_lon, dt); } #define MAX_LOITER_POS_VEL_VELOCITY 1000 // loiter_set_pos_from_velocity - loiter velocity controller with desired velocity provided in front/right directions in cm/s static void loiter_set_pos_from_velocity(int16_t vel_forward_cms, int16_t vel_right_cms, float dt) { int32_t vel_lat; int32_t vel_lon; int32_t vel_total; vel_lat = vel_forward_cms*cos_yaw - vel_right_cms*sin_yaw; vel_lon = vel_forward_cms*sin_yaw + vel_right_cms*cos_yaw; // constrain the velocity vector and scale if necessary vel_total = safe_sqrt(vel_lat*vel_lat + vel_lon*vel_lon); if( vel_total > MAX_LOITER_POS_VEL_VELOCITY ) { vel_lat = MAX_LOITER_POS_VEL_VELOCITY * vel_lat/vel_total; vel_lon = MAX_LOITER_POS_VEL_VELOCITY * vel_lon/vel_total; } // update loiter target position loiter_lat_from_home_cm += vel_lat * dt; loiter_lon_from_home_cm += vel_lon * dt; // update next_WP location for reporting purposes next_WP.lat = home.lat + loiter_lat_from_home_cm; next_WP.lng = home.lng + loiter_lat_from_home_cm * scaleLongUp; } // loiter_set_target - set loiter's target position from home in cm static void loiter_set_target(float lat_from_home_cm, float lon_from_home_cm) { loiter_lat_from_home_cm = lat_from_home_cm; loiter_lon_from_home_cm = lon_from_home_cm; // update next_WP location for reporting purposes next_WP.lat = home.lat + loiter_lat_from_home_cm; next_WP.lng = home.lng + loiter_lat_from_home_cm * scaleLongUp; }