ArduPilot Copter Release Notes: ------------------------------------------------------------------ Copter 4.0.3 28-Feb-2020 / 4.0.3-rc1 20-Feb-2020 Changes from 4.0.2 1) Bug Fixes: a) "RCInput: decoding" message watchdog reset when using MAVLink signing (Critical Fix) b) HeliQuad yaw control fix c) Do-Set-Servo commands can affect sprayer, gripper outputs d) BLHeli passthrough fix for H7 boards (CubeOrange, Holybro Durandal) 2) USB IDs updated for "composite" devices (fixes GCS<->autopilot connection issues for boards which present 2 USB ports) 3) RCOut banner helps confirm correct setup for pwm, oneshot, dshot 4) ZigZag mode supports arming, takeoff and landing ------------------------------------------------------------------ Copter 4.0.2 11-Feb-2020 Changes from 4.0.2-rc4 1) MAVFTP stack size increased to 3k (fixes reboot when using MAVFTP) ------------------------------------------------------------------ Copter 4.0.2 11-Feb-2020 / 4.0.2-rc4 05-Feb-2020 Changes from 4.0.2-rc3 1) Bug Fixes: a) Spektrum receivers decoding fix for Pixracer b) Current Alt frame always relative to home (RTL could return at wrong alt) c) Circle mode pitch control direction fixed d) EKF only uses world magnetic tables if COMPASS_SCALE is set e) Logging reliability improvements especially for FRAM logs f) RangeFinders using PWM interface use RNGFNDx_OFFSET param (attempt2) g) SpeedyBeeF5 probes all I2C ports for external baro 2) Rangefinder fallback support (both must have same _ORIENT) ------------------------------------------------------------------ Copter 4.0.2-rc3 01-Feb-2020 Changes from 4.0.2-rc2 1) Bug Fixes: a) AutoTune fix to restore original gains when AutoTune completes ------------------------------------------------------------------ Copter 4.0.2-rc2 31-Jan-2020 Changes from 4.0.1 1) Bug Fixes: b) IO CPU timing fix which reduces ESC sync issues c) PX4Flow driver probes all I2C ports on Hex Cubes d) RangeFinders using PWM interface (like Garmin LidarLite) use RNGFNDx_OFFSET param e) RC override fix when RC_OVERRIDE_TIME=-1 (allows disabling timeout when using joystick) f) TradHeli attitude control parameter description fixes (does not affect flight) g) cygwin compiler fix (affects developers only) 2) Minor enhancements: a) GCS failsafe warning lights and tones b) Circle mode pitch control direction swapped ------------------------------------------------------------------ Copter 4.0.1 25-Jan-2020 / 4.0.1-rc3 19-Jan-2020 Changes from 4.0.1-rc2 1) Bug Fixes: a) Semaphore fixes for Logging, Filesystem and UAVCAN Dyanmic Node Allocation b) RangeFinder parameter fix (4th rangefinder was using 1st rangefinder's params) c) TradHeli STB_COL_x parameter description fixed 2) Minor Enhancements: a) Autorotate flight mode renamed to Heli_Autorotate b) Solo default parameters updated c) "Prepared log system" initialisation message removed ------------------------------------------------------------------ Copter 4.0.1-rc2 10-Jan-2020 Changes from 4.0.1-rc1 1) FrSky telemetry status text handling fix (Critical Fix) ------------------------------------------------------------------ Copter 4.0.1-rc1 10-Jan-2020 Changes from 4.0.0 1) Circle mode allows pilot control of radius and rotation speed 2) CAN servo feedback logged 3) Magnetic declination tables updated 4) Serial0 protocol forced to MAVLink (avoids accidental disabling of USB port) 5) Bug Fixes: a) TradHeli RSC RC passthrough fixed b) CubeOrange and Durandal I2C timing fixed (was running slow) c) Compass calibration auto orientation skips "pitch 7" which could cause cal to fail d) Durandal's fourth I2C port fixed e) Linux boards with CAN support fixed f) Neopixel added to SERVOx_FUNCTION param description g) NMEA Output fixed (was sending an extra CR) h) Optflow messages sent even if EKF has no height estimate i) SkyViper build fixed j) Spektrum/DSM 22ms RC input fixed k) "UC Node Down" message removed (was unnecessarily scary) ------------------------------------------------------------------ Copter 4.0.0 29-Dec-2019 / 4.0.0-rc6 28-Dec-2019 Changes from 4.0.0-rc5 1) Compiler updated to gcc 6.3.1 (2nd attempt) ------------------------------------------------------------------ Copter 4.0.0-rc5 23-Dec-2019 Changes from 4.0.0-rc4 1) RM3100 compass enabled on all boards 2) GCS failsafe disabled by default (see FS_GCS_ENABLE parameter) 3) Bug Fixes a) Bootloader fix for H7 boards (could brick CubeOrange, CUAV V5 Nano, etc) b) OmnibusF4pro GPS fix c) MatekF405-Wing missing serial ports restored d) MatekF765-Wing RTSCTS parameter defaults set correctly e) CUAV V5 Nano battery monitor param defaults improved ------------------------------------------------------------------ Copter 4.0.0-rc4 20-Dec-2019 Changes from 4.0.0-rc3 1) Compiler updated to gcc 6.3.1 2) Solo default parameters updated 3) Bug Fix to RCMAP channel number sanity check ------------------------------------------------------------------ Copter 4.0.0-rc3 16-Dec-2019 Changes from 4.0.0-rc2 1) Flight mode and control improvements: a) Auto mode Takeoff getting stuck fixed (very rare) b) AutoTune protection against ESC sync loss at beginning of a twitch c) SystemID mode parameters hidden by default (set SID_AXIS to non-zero to see all) d) Takeoff from slanted surfaces improved by reducing I-term build-up in attitude controllers 2) Lua Script related enhancements: a) MAV FTP support to ease uploading and downloading Lua scripts b) NeoPixel/WS2812 LED control from Lua scripts c) Pre-arm check that Lua scripting feature has enough memory 3) TradHeli enhancements: a) Autonomous autorotation (compile time option, not available in stable firmware) b) CCW Direct Drive Fixed Pitch tail support (see H_TAIL_TYPE parameter) c) Parameter description improvements d) STAB_COL_1/2/3 param range changed to 0 to 100 (was 0 to 1000) 4) Lightware SF40c driver for latest sensors with "streaming" protocol 5) Board/Frame specfic fixes: a) Hex CubeOrange IMU heater control gain tuning improvement b) Holybro Durandal IMUs ordering fix so EKx_IMU_MASK bits are intuitive c) Holybro Pixhawk4 B/E LED fix (was flickering) d) MatekF765 PWM outputs 5 and 6 now functional e) MatekF765, MatekF405 time wrap CRITICAL fix for vehicles flying more than 72min f) MatekF765 LED fixes g) mRobotics ControlZeroF7 I2C bus numbering fix h) Solo default params updated for 4.0.0 i) Bootloaders for boards using STM32H7 CPUs j) Bootloader protection against line noise that could cause the board to get stuck during bootup k) LED timing fix for FMUv5 boards with LEDs on one of first four auxiliary PWM outputs 6) Minor Enhancements and Bug Fixes a) I2C storm High level protection b) Internal errors (like I2C storms) reported to GCS by setting Heartbeat status to Critical c) Dataflash Logging CTUN.TAlt and SAlt scaling fixed d) DO_DIGICAM_CONTROL messages are sent using Mavlink1/2 as specified by SERIALx_PROTOCOL e) DO_SET_SPEED sanity check fixed to protect against negative speeds f) FrSky telemetry scheduling improvement (fixes issue in which GPS data would not be sent) g) GPS auto configuration fix for non-Ublox-F9 (F9 config was interfering with other Ublox GPSs) h) Landing gear DEPLOY message fix (could be displayed multiple times or when gear not configured) i) Pre-arm check of position estimate when arming in Loiter even if arming is "forced" j) Pre-arm check that Terrain database has enough memory k) RangeFinder parameter conversion fix (some parameters were not upgraded from 3.6.x to 4.0.0) l) RangeFinder TYPE parameter descriptions clarified for LidarLite and Benewake Lidars m) Serial parameters hidden if they do not exist on the particular board n) UAVCAN GPS fix for GPSs that don't provide "Aux" message (like the Here2) o) NMEA Output bug fix (output was stopping after 90 seconds) ------------------------------------------------------------------ Copter 4.0.0-rc2 04-Nov-2019 Changes from 4.0.0-rc1 1) Failsafe changes: a) GCS failsafe triggers when telemetry connection is lost (previously only triggered when using joystick) b) FS_OPTION parameter allows continue-in-auto and continue-in-pilot-modes for RC/Radio and GCS failsafe 2) Dynamic Notch Filter supports filter range based on BLHeli ESC feedback 3) Improved protection against high roll/pitch gains affecting altitude control 4) Bug Fixes: a) Altitude control param conversion fix (PSC_ACCZ_FILT converted to PSC_ACCZ_FLTE) b) BLHeli fix to RPM calcs and telemetry (aka 0x8000 error) c) ChibiOS SPI timeout fix (non-critical) d) Fence upload is less strict about altitude types (fences don't have altitudes) e) Motor loss detection bug fix (would sometimes think the wrong motor had failed) f) Pre-arm message fix to reports AHRS/EKF issue (was blank) g) Sparky2 autopilot firmware available h) Startup message "AK09916: Unable to get bus semaphore" removed (was not an error) i) Yaw control fix for fast descent and after large attitude disturbances ------------------------------------------------------------------ Copter 4.0.0-rc1 25-Oct-2019 Changes from 3.6.11 1) Path Planning for Object Avoidance (aka Bendy Ruler and Dijkstra's) replaces "Dodge" avoidance 2) Complex Fence support (aka stay-out zones) 3) Lua scripting support on the flight controller 4) New flight controllers: a) Hex Cube Orange b) Holybro Durandal 5) Attitude Control changes: a) Attitude Control filters on target, Error and D-term (see ATC_RAT_x_FLTT/FLTE/FLTD) b) Harmonic notch filter 6) Flight mode changes: a) ZigZag mode (designed for crop spraying) b) SystemId for "chirping" attitude controllers to determine vehicle response c) StandBy mode for vehicles with multiple flight controllers d) SmartRTL provides warnings when buffer is nearly full e) Follow mode offsets reset to zero when vehicle leaves follow mode f) Upward facing surface tracking using lidar g) Circle mode points more accurately towards center 7) Traditional Heli: a) Removed the parameter H_LAND_COL_MIN and functionality now uses H_COL_MID. CAUTION: ensure H_COL_MID is set to collective blade pitch that produces zero thrust b) Incorporated a rotor speed governor in rotor speed control (RSC) c) Moved all RSC parameters to the RSC library d) Converted throttle curve parameters to percent e) Converted RSC_CRITICAL, RSC_IDLE, and RSC_SETPOINT to percent f) Created swashplate library that has presaved swashplate types for use with Heli_Single and Heli_Dual frames g) Motor interlock with passthrough settable through RC option feature h) Removed collective too high pre-arm check i) Added virtual flybar for Acro flight mode j) Fixed H_SV_MAN minimum and maximum settings for Heli_Dual 8) Frames: a) BiCopter support b) OctoV mixing improvements 9) RC input/output changes: a) Serial protocols supported on any serial port b) IBUS R/C input support c) DO_SET_SERVO and manual passthrough can operate on the same channel 10) Battery improvements: a) Up to 10 batteries can be monitored b) "Sum" type consolidates monitoring across batteries c) Fuel flow battery (for use with gas tanks) 11) Sensor/Accessory changes: a) Robotis servo support b) KDECAN ESCs c) ToshibaCAN ESCs d) BenewakeTF03 lidar e) SD Card reliability improvements (if card removed, logging restarts) f) Yaw from some GPS (including uBlox RTK GPS with moving baseline) g) WS2812 LEDs (aka NeoPixel LEDs) h) NTF_BUZZ_VOLUME allows controlling buzzer volume 12) Landing Gear: a) Retracts automatically after Takeoff in Auto completes b) Deployed automatically using SRTM database or Lidar 13) UAVCAN improvements: a) dynamic node allocation b) SLCAN pass-through c) support for UAVCAN rangefinders, buzzers, safety switch, safety LED 14) Serial and Telemetry: a) MAVLink Message-Interval allows reducing telemetry bandwidth requirements b) SERIALn_OPTIONS for inversion, half-duplex and swap 15) Safety Improvements: a) Vibration failsafe (switches to vibration resistant estimation and control) b) Independent WatchDog gets improved logging c) EKF failsafe triggers slightly more quickly ------------------------------------------------------------------ Copter 3.6.11 01-Oct-2019 / 3.6.11-rc1 16-Sep-2019 Changes from 3.6.10 1) EKF and IMU improvements: a) IMU3 enabled by default if present b) IMU3 fast sampling enabled by default on Cube autopilots c) EKF protection against large baro spikes causing attitude error d) EKF origin fixes (consistent across cores, set externally only when not using GPS) e) EKF logging of 3rd core 2) Minor enhancements: a) Land mode supports heading requests (ie. ROI) b) Support Hexa-H frame c) MatekF405-STD binaries created d) Benewake TFminiPlus lidar support 3) Bug Fixes a) Barometer health checks include sanity check of temperature b) Lightware serial driver handles invalid distances c) IO firmware fix involving delayed writes to serial ports (ChibiOS only) d) CAN Compass fis to for unintialised device IDs e) mRo x2.1-777 USB ID fix f) ChibiOS fix for I2C storm ------------------------------------------------------------------ Copter 3.6.10 29-Jul-2019 / 3.6.10-rc2 2-Jul-2019 Changes from 3.6.10-rc1 1) mRobotics ControlZeroF7 board support 2) Motor Test fixed by removing delay that triggered CPU Watch Dog ------------------------------------------------------------------ Copter 3.6.10-rc1 08-Jul-2019 Changes from 3.6.9 1) EKF improvements: a) learns biases even for inactive IMUs b) EKF uses earth magnetic field model to reduce in-flight compass errors c) EKF switches to first healthy IMU when disarmed d) IMU fix for dropped samples during high CPU usage e) Optical flow fusion start fix when some gyros disabled 2) Ublox F9 GPS support 3) Integrated CPU Watch Dog for STM boards including logging of reset reason 4) ChibiOS I/O firmware for ChibiOS builds to support Spektrum binding 5) Auxiliary switch changes always logged 6) CUAVv5 Nano LED fix 7) Solo Gimbal fix when some gyros disabled ------------------------------------------------------------------ Copter 3.6.9 27-May-2019 / 3.6.9-rc1/rc2 30-Apr-2019 Changes from 3.6.8 1) CX-OF flow sensor enabled on all boards 2) CUAVv5 Nano board support added 3) RangeFinders supported on all I2C ports 4) Compass maximum acceptable offsets increased 5) Septentrio GPS driver loses logging of camera feedback which could cause lag 6) Bug Fixes: a) Acro mode leveling fix for when ACRO_TRAINER was 1 b) Tradheli collective position pre-arm check removed c) Fallback to microSD for storage fixed d) GPS blending memory access fix that could lead to unhealthy GPS e) fixed POWR flags for 2nd power module on fmuv3 boards 7) bootloader binary update for many boards ------------------------------------------------------------------ Copter 3.6.8 26-Apr-2019 / 3.6.8-rc1 24-Apr-2019 Changes from 3.6.7 1) Safety fixes a) Prevent loss of active IMU from causing loss of attitude control b) Added startup check for Hex CubeBlack sensor failure c) don't reset INS_ENABLE_MASK based on found IMUs ------------------------------------------------------------------ Copter 3.6.7 06-Mar-2019 / 3.6.7-rc1 28-Feb-2019 Changes from 3.6.6 1) Bug fixes and minor enhancements a) Matek405-Wing compass fix (thread initialisation fix) b) Landing flips reduced by reducing I-term build-up c) Land mission command slows down less aggressively d) Lightware LW20 lidar more reliably switches to serial mode ------------------------------------------------------------------ Copter 3.6.6 15-Feb-2019 / Copter 3.6.6-rc2 09-Feb-2019 Changes from 3.6.6-rc1 1) Bug fixes a) EKF compass switching fix for vehicles with 3 compasses b) CAN fixed on Pixhawk4 and PH4-mini c) Mini-pix uart telem1 and telem2 reversed d) Divide-by-zero protection if _FILT_HZ params set to zero e) Guided_NoGPS skips GPS pre-arm check ------------------------------------------------------------------ Copter 3.6.6-rc1 02-Feb-2019 Changes from 3.6.5 1) AP_RSSI fixes and minor enhancements a) RSSI pwm input driver for ChibiOS b) add V5 Nano to RSSI_ANA_PIN parameter description 2) Bug fixes and minor enhancements a) TradHeli roll trim ramp time fix b) First Spline waypoint no longer skipped c) RC override (from GCS Joystick) disable fix (command to disable overrides could be interpreted as real input) ------------------------------------------------------------------ Copter 3.6.5 24-Jan-2019 / 3.6.5-rc3 21-Jan-2019 Changes from 3.6.5-rc2 1) Bug fixes: a) Pixhawk4 SBUS input and Serial6 pin mapping conflict resolved ------------------------------------------------------------------ Copter 3.6.5-rc2 15-Jan-2019 Changes from 3.6.5-rc1 1) Bug fixes and minor enhancements a) RC DSM sync bug fix (channel 8 could temporarily become zero, ChibiOS only) b) Pixhawk board LED fix (ChibiOS only) ------------------------------------------------------------------ Copter 3.6.5-rc1 11-Jan-2019 Changes from 3.6.4 1) Bug fixes and minor enhancements a) SD Card reliability improvement (BRD_SD_SLOWDOWN param) and allow re-inserting card after boot b) Mode and Auxiliary switch range check to protect during FrSky SBUS failsafe recovery c) Follow mode reports target distance and heading to ground station d) Pixhawk4-mini safety switch and LED fix e) Bebop2 build fix 2) RC protocol decoding for SRXL, SUMD and ST24 extended to all boards including pixracer and ChibiOS-only boards 3) DrotekP3 Pro support 4) Cube Purple support ------------------------------------------------------------------ Copter 3.6.4 27-Dec-2018 / 3.6.4-rc1 20-Dec-2018 Changes from 3.6.3 1) Bug fixes and minor enhancements a) Detect and clear stuck I2C bus when using ChibiOS b) Pixhawk4 fix for battery monitor voltage scaling c) TradHeli Dual (aka Chinook) fix for scaling of second swashplate movement d) Omnibus F7 IMU orientation fix e) Gimbal fix to avoid extreme movement if pilot's transmitter is off at startup f) Follow mode fix to obey FOLL_SYSID parameter (controls which vehicle to follow) 2) Cheerson CX-OF optical flow sensor support ------------------------------------------------------------------ Copter 3.6.3 04-Dec-2018 / 3.6.3-rc1 01-Dec-2018 Changes from 3.6.2 1) Bug fixes and minor enhancements a) Pixhawk4 RC input fix b) TradHeli parameter default fixes for Loiter and PosHold c) Onboard OSD fix for MatekSys 405 d) Solo power off button delay time increased ------------------------------------------------------------------ Copter 3.6.2 24-Nov-2018 / 3.6.2-rc4 22-Nov-2018 Changes from 3.6.2-rc3 1) Bug fixes and minor changes: a) Benewake TFmini short range scaling fix b) Fix alt drop after quick switch from RTL to stabilize to RTL c) Winch removed from build by default ------------------------------------------------------------------ Copter 3.6.2-rc3 19-Nov-2018 Changes from 3.6.2-rc2 1) Bug fixes: a) Benewake TFmini and TF02 driver reliability fix b) Spektrum RC parsing fix when more than 7 channels 2) remove bootloader from px4-v2 builds (reduces firmware size) ------------------------------------------------------------------ Copter 3.6.2-rc1/rc2 15-Nov-2018 Changes from 3.6.1 1) Bug fixes: a) Benewake TFmini and TF02 driver checksum fix (was missing many sensor readings) b) Range finders report healthy to GCS when out-of-range c) RPM sensor reliability fix by initialising analog input pin ------------------------------------------------------------------ Copter 3.6.1 10-Nov-2018 / 3.6.1-rc1 06-Nov-2018 Changes from 3.6.0 1) Garmin LidarLite V3HP support 2) VFR HUD messages send relative altitude if DEV_OPTIONS = 2. Useful for older OSDs and GCSs 3) Bug fixes: a) Battery failsafe voltage parameter conversion fix b) Safety switch startup fix (was occasionally not initialised properly) c) Benewake TFmini and TF02 driver discards distances over 327m (avoids reporting 655m when can't read distance) d) Dataflash erase only availabled when disarmed (avoids crash if user attempted to erase logs while flying) 4) ChibiOS fixes and enhancements: a) Pixracer LEDs colours fixed b) Terrain support fixed on Pixracer, MindPx-v2, Radiolink mini-pix c) RC input processing fix to avoid memory corruption in some rare cases d) FuriousFPV F-35 Lightning board support e) SpeedyBee F4 board support f) Bootloaders for OmnibusF4v6, mRoX2.1-777, Radiolink mini-pix g) Revo-mini support for external barometer h) Pins numbers made consistent across boards (setup of some features now more consistent across boards) i) enable safety switch on Pixhawk family f7 boards ------------------------------------------------------------------ Copter 3.6.0 26-Oct-2018 Changes from 3.6.0-rc12 1) Bug Fixes: a) Object avoidance fix when using 360 Lidar (mini fence was not including first distance) b) Flowhold mode descending fix 2) ChibiOS related fixes: a) Kakutef7 support pin mapping fixes b) PixRacer LED fix c) I2C Lidar driver fix to avoid freeze at startup if sensor not connected ------------------------------------------------------------------ Copter 3.6.0-rc12 05-Oct-2018 Changes from 3.6.0-rc11 1) Bug Fixes: a) DSHot ESC driver race condition fix (could result in board freezing up) b) EKF fix to rounding off home altitude (could result in slightly inaccurate home altitude) c) Pixracer safety switch fix (BRD_SAFETYOPTION parameter was handled incorrectly) ------------------------------------------------------------------ Copter 3.6.0-rc11 01-Oct-2018 Changes from 3.6.0-rc10 1) Bug Fixes: a) PosHold fix to initialise desired accelerations b) Automatic compass orientation fix to account for equivalent rotations c) ChibiOS fix to RSSI voltage reading ------------------------------------------------------------------ Copter 3.6.0-rc10 15-Sep-2018 Changes from 3.6.0-rc9 1) Arming/disarming from transmitter can be disabled with ARMING_RUDDER parameter 2) ChibiOS fixes: a) UART baud rate rounding fix (allow 921600 baud to work) b) ADC fix to allow more simultaneous channels 3) Bug Fixes: a) Lean angle limit (to maintain altitude) always allows at least 10deg of lean b) Attitude Control and PID initialisation fix to reduce twitches when switching modes ------------------------------------------------------------------ Copter 3.6.0-rc9 08-Sep-2018 Changes from 3.6.0-rc8 1) Landing gear can be operated using AIRFRAME_CONFIGURATION mavlink messages 2) Support playing tunes received via MAVLink (i.e. from GCS) 3) Bug Fixes: a) Twitch reduced when entering Loiter at high speed b) Safety switch state fix when Pixhawk/Cube I/O board reset in flight c) External display fix to allow plugging into either I2C port ------------------------------------------------------------------ Copter 3.6.0-rc8 28-Aug-2018 Changes from 3.6.0-rc7 1) TeraRanger Tower EVO lidar support added 2) PCA9685 and NCA5623 LED support added (replacements for Toshiba LED that is becoming end-of-life) 3) Missions can start with DO_ commands (first NAV command must still be takeoff) 4) ChibiOS fixes: a) DShot and BLHeli stability improvements b) added OmnibusNanoV6 bootloader 5) Bug fixes: a) AP_Stat only saves values to eeprom if they change (reduces CPU impact) b) boost throttle respects safety switch c) TradHeli reduce chance of tip-over when landed in Loiter ------------------------------------------------------------------ Copter 3.6.0-rc7 01-Aug-2018 Changes from 3.6.0-rc6 1) Compass rotation detection during calibration (see COMPASS_AUTO_ROT param) 2) Tone alarm system consistent on all boards and support for playing tones from GCS 3) OnBoard OSD improvements including showing dir to home (ChibiOS only) 4) External compass support and microSD improvements for many ChibiOS-only boards including Kakute F4, Mateksys F405-Wing, Airbot F4, Crazyflie2, MindPXv2, Mini-PIX, Omnibus F7 5) Bug fixes: a) Battery monitor parameter fix to support BLHeli ESCs b) Ch12 auxiliary function fixed c) compassmot fix d) Pixracer external compass fix e) Pre-arm failure regarding RCx_TRIM removed for non critical channels f) SBUS failsafe fix when receiver configured to "hold" g) UART flow control fixes (ChibiOS only) h) VL53L0X lidar fix 6) Minor enhancements: a) Compass device IDs (i.e. COMPASS_DEVID) set to zero if no compass detected b) Fence action "Always Land" option added c) Motor test maximum time extended to 10min d) Receiver RSSI pwm input on AUX5,6 e) USB Serial port protocol default set to Mavlink2 7) TradHeli fixes: a) "Channel already assigned" message fixed b) External gyro output method PWM based c) Swash servo output properly accounts for servo trim ------------------------------------------------------------------ Copter 3.6.0-rc6 16-Jul-2018 Changes from 3.6.0-rc5 1) ChibiOS small enhancement and fixes: a) KakuteF4 UART order fix b) mRobotics bootloader and autobuild of binaries for AUAV2.1 and Pixracer c) Mateksys F405-Wing uart reorder to better match labels on board 2) Improve telemetry/GPS detection by only clearing UART when baud rate changes ------------------------------------------------------------------ Copter 3.6.0-rc5 07-Jul-2018 Changes from 3.6.0-rc4 1) Support new boards CubeBlack and HolyBro Pixhawk4-mini 2) ChibiOS small enhancement and fixes: a) make board serial number match NuttX b) relay fix for Pixhawk boards by defaulting BRD_PWM_COUNT to 4 (same as NuttX) c) MatekF405-Wing default compass orientation fix d) Pixhawk4 default compass orientation fix e) Omnibus F4 Pro I2C fix 3) Bug fixes: a) Telemetry baud rate fix b) RC failsafe fix to RTL in all modes except Auto when FS_THR_ENABLE is continue-with-mission c) waypoint navigation related safety check that PSC_POS_XY_P is non-zero d) aerofc-v1 update bootloader utility fix ------------------------------------------------------------------ Copter 3.6.0-rc4 05-Jul-2018 Changes from 3.6.0-rc3 1) add support for Cube Black and Cube Orange 2) Built-in OSD improvements including home direction fix, altitude fix 3) Bug fixes: a) ESC Telemetry current scaling fix b) LED pre-arm GPS colour fix if glitch occurs ------------------------------------------------------------------ Copter 3.6.0-rc3 02-Jul-2018 Changes from 3.6.0-rc2 1) ChibiOS: a) airbotf4, matekF405, matekF405-wing, omnibusf4pro, mini-pix, omnibusf7v2, revo-mini, sparky2 binaries built on firmware.ardupilot.org b) STM32F7 support including the CUAV v5 Autopilot and the PixHawk 4 (aka fmuv5) c) fixed dataflash logfile dates d) bootloader included in firmware for easier uploading e) additional UART added to fmuv4 and fmuv5 (STM32 F7 boards) f) ChibiOS version written to dataflash log files 2) TradHeli a) fix collective jump on rotor shutdown in AltHold and Loiter b) fix interlock pre-arm check 3) Follow uses relative altitudes (FOLL_ALT_TYPE param allows specifying relative or absolute alts) 4) Auxiliary switch de-bounced to avoid false positives 5) Bug fixes and minor enhancements: a) ESC calibration fix b) ESC_TELEMETRY messages sent to ground station ------------------------------------------------------------------ Copter 3.6.0-rc2 01-Jun-2018 Changes from 3.6.0-rc1 1) ChibiOS support for Holybro Kakute F4 2) Range finders: a) Benewake TFmini and TF02 support b) WASP200 laser range finder support 3) D-Shot and ESC telemetry support 4) Vision-position-estimate support for use with ROS 5) Bug fixes and minor enhancements: a) TradHeli swash plate servo trim fixes b) SmartRTL gives pilot yaw control c) marvelmind reliability improvements d) CoaxCopter and SingleCopter output fixes e) Maxbotics I2C sonar health fix 6) Safety fixes/improvements: a) GPS/EKF failsafe disabled in Acro/Stabilize modes b) interlock switch arming check fixed c) Auxiliary switch de-bouncing d) pre-arm check for GPS/AHRS difference changed to 2D (to avoid false positives) e) startup crash fixed when VL53L0X lidar configured but not connected ------------------------------------------------------------------ Copter 3.6.0-rc1 19-Apr-2018 Changes from 3.5.5 1) ChibiOS support including F4BY, OpenPilot Revo Mini, TauLabs Sparky2 boards 2) Flight mode changes: a) New Loiter with faster roll and pitch response, braking b) SmartRTL (returns home using outgoing path) c) Follow mode (allows following without relying on ground station commands) d) FlowHold (position hold with optical flow without lidar) 3) Battery failsafe allows two stages of actions and monitoring of multiple batteries 4) New sensors/drivers: a) Marvelmind for Non-GPS navigation b) RPLidarA2/A3 for object avoidance c) Winch for lowering packages without landing d) Septentrio GPS driver robustness improved 5) New frames: a) dodeca-hexa copter (12 motors on 6 arms) b) Variable pitch quadcopter support (aka HeliQuad) c) multicopters with vertical boosting motor (see MOT_BOOST_SCALE parameter) 6) Miscellaneous changes and enhancements: a) Auxiliary switch to enable/disable RC overrides from ground station joystick b) Barometer temperature calibration learning (see TCAL_ENABLED parameter) c) Camera triggering by distance only in Auto mode if CAM_AUTO_ONLY set to 1 d) Compass noise rejection using COMPASS_FLTR_RNG parameter e) Compass interference compensation for up to 4 motors (see COMPASS_PMOT parameters) f) Command Line Interface (aka CLI) removed to reduce firmware size g) Flight mode channel can be changed using FLTMODE_CH parameter h) IMU notch filter to ignore specific frequencies (use INS_NOTCH_ENABLE parameter) i) LAND_ALT_LOW parameter allows setting altitude at which vehicle slows to LAND_SPEED in Land and RTL modes j) Mission cleared automatically on each reboot if MIS_OPTIONS parameter set to 1 k) Object avoidance configurable to "stick" to barriers (previously would always slide past) l) PILOT_SPEED_UP, PILOT_SPEED_DN allow different max climb and descent rates in AltHold, Loiter, PosHold m) Safety switch configurable (i.e. only allow arming but not disarming via switch) n) Servo output rate configurable (see SERVO_RATE parameter) o) Vehicle rotation rate limits (see ATC_RATE_P/R/Y_MAX parameters) p) SI units in parameters, mavlink messages and dataflash logs 7) TradHeli improvements: a) H3-135/140 swashplate support b) Reversed collective option for leading/trailing edge control c) AltHold angle limiter fix d) Five point spline-smoothed throttle curve 8) parameter and log message name changes: a) ACCEL_Z_ renamed to PSC_ACCZ_ b) ACC_ parameters renamed to PSC_ACC c) POS_ parameters renamed to PSC_POS d) VEL_ parameters renamed to PSC_VEL e) FS_BATT_ renamed to BATT_FS_ f) BATT_AMP_PERVOLT renamed to BATT_AMP_PERVLT g) PILOT_VELZ_MAX to PILOT_SPEED_UP (and PILOT_SPEED_DN) h) RC_FEEL_RP replaced with ATC_INPUT_TC (functionality is same, scaling is different) i) WPNAV_LOIT_ params renamed to LOIT_ j) NTUN dataflash message renamed to PSC ------------------------------------------------------------------ Copter 3.5.7 17-Jul-2018 / 3.5.7-rc1 12-Jul-2018 Changes from 3.5.6 1) Bug fix to ESC calibration safety switch issue ------------------------------------------------------------------ Copter 3.5.6 11-Jul-2018 / 3.5.6-rc1 07-Jul-2018 Changes from 3.5.5 1) Safety switch fix to refuse presses once armed (BRD_SAFETYOPTION controls behaviour) ------------------------------------------------------------------ Copter 3.5.5 31-Jan-2018 / 3.5.5-rc1 24-Jan-2018 Changes from 3.5.4 1) ICM20948 compass orientation fix 2) LIS3MDL compass support on Pixracer 3) support for easy embedding of defaults in firmware binary 4) do-mount-control control command sets copter yaw when using 2-axis gimbal 5) TradHeli fix for direct drive variable pitch tail rotors ------------------------------------------------------------------ Copter 3.5.4 23-Nov-2017 / 3.5.4-rc2 17-Nov-2017 Changes from 3.5.3 1) Compass improvements / bug fixes: a) probe for LIS3MDL on I2C address 0x1e b) bug fix pixracer compass detection ------------------------------------------------------------------ Copter 3.5.4-rc1 08-Nov-2017 Changes from 3.5.3 1) Compass improvements: a) support added for QMC5883L, LIS3MDL, IST8310 b) COMPASS_TYPEMASK parameter allows enabling/disabling individual compass drivers 2) LightWare and MaxBotix range finders supported on both I2C buses 3) Serial port 5 can be used for telemetry or sensors (previously was only for NuttX console) 4) px4pro flight controller supported 5) TradHeli fixes: a) motor runup check applies to all flight modes (previously only loiter, poshold, althold) b) swashplate behaviour changes when on ground in acro, stabilize and althold c) servo test function fixed d) direct drive fixed pitch tail fix e) Z-axis Accel P gain default lowered to 0.3 6) EKF origin set using SET_GPS_GLOBAL_ORIGIN mavlink message instead of SET_HOME_POSITION 7) Intel Aero supports 921600 baud rate between main flight controller and companion computer 8) Bug fix to I2C race condition on Pixhawk that could occasionally cause I2C device to not be detected ------------------------------------------------------------------ Copter 3.5.3 21-Sep-2017 / Copter 3.5.3-rc1 12-Sep-2017 Changes from 3.5.2 1) Guided mode support yaw and yaw-rate fields from set-position-target message 2) Optical Flow startup retries 10 times 3) Bug fixes: a) Septentrio RTK GPS driver robustness improvements for long messages b) dataflash not-logging checks if not initialised c) fix reporting of relative-position-NE-to-home (most users will not notice this difference) ------------------------------------------------------------------ Copter 3.5.2 14-Aug-2017 / Copter 3.5.2-rc1 05-Aug-2017 Changes from 3.5.1 1) GPS glitch arming check and notification (flashing blue-yellow LED, message on HUD) 2) Arming check for minimum voltage (see ARMING_VOLT_MIN parameter) 3) Landing Gear startup behaviour now configurable (see LGR_STARTUP parameter) 4) Solo LED fix when using "boat" mode 5) Intel Aero RTF gets one more I2C bus 6) Bug fixes: a) resolve barometer floating point exception when ground pressure set to be negative b) resolve freeze if SERVOx_FUNCTION is set above 80 ------------------------------------------------------------------ Copter 3.5.1 31-July-2017 / 3.5.1-rc1 24-July-2017 Changes from 3.5.0 1) fix to RC input corruption when using Spektrum DSMx with Pixracer ------------------------------------------------------------------ Copter 3.5.0 17-July-2017 / 3.5.0-rc11 12-July-2017 Changes from 3.5-rc10 1) GPS fixes: a) Re-enable auto detection of NMEA GPS (revert change from -rc9) b) Fix SBF race condition on start (this should resolve SBF GPS detection issues for some users) 2) SF40c driver fix to ignore zero distances ------------------------------------------------------------------ Copter 3.5.0-rc10 08-July-2017 Changes from 3.5-rc9 1) Intel Aero build and default parameter updates 2) EKF final yaw reset lowered from 5m to 2.5m to speed up bad compass detection after takeoff ------------------------------------------------------------------ Copter 3.5.0-rc9 03-July-2017 Changes from 3.5-rc8 1) AutoTune improvement when using position hold (twitches in body-frame instead of earth-frame) 2) GPS fixes: a) RTK GPS fix when large RTK correction messages are sent b) auto-detection for NMEA disabled (NMEA users must explicitly set GPS_TYPE to 5) 3) EKF bug fixes: a) fix bug preventing use of optical flow for terrain height estimation b) fix bug affecting accuracy of optical flow estimated height during climb/descent c) fix range beacon fusion bugs 4) return accel filter (INS_ACCEL_FILT) to 20hz (some users were seeing oscillations at 10hz) ------------------------------------------------------------------ Copter 3.5.0-rc8 15-Jun-2017 Changes from 3.5-rc7 1) Solo on Master: a) add/fix tones and LED support b) resolve dataflash health reporting issue 2) Allow flight controller to boot even if critical sensors fail (previously stopped at startup and displayed message people could rarely see) 3) Minor enhancements: a) Landing Gear retracts/deploys only when pilot first moves switch (previously would always deploy on startup) b) BeagleBoneBlue supports external compass, OLED display 4) Bug fixes: a) increase pilot stick dead zones for roll, pitch and yaw (still slightly more narrow than AC3.4) b) increase default roll, pitch and yaw rate IMAX values to 0.5, reduce default yaw rate filter to 2.5hz c) reduce accel filter from 20hz to 10hz (smoothes throttle in AltHold) d) fix EKF declination fusion e) object avoidance fix to ignore old distance measurements and out-of-range distances from range finder f) fix poxyz west-east processing (it was backwards) ------------------------------------------------------------------ Copter 3.5-rc7 25-May-2017 Changes from 3.5-rc6 1) Bug fixes and minor enhancements: a) fix OneShot ESC calibration and compass-mot calibration b) fix Navio2 and ErleBrain crashes caused by insufficient memory allocated to scheduler c) AutoTune with position hold only resets target position when roll and/or pitch sticks moved d) fix Acro, Sport trainer mode to stop attitude targets going beyond angle limits e) sanity check WPNAV_RADIUS is non-zero f) MarvelMind driver fixes (still a work-in-progress) g) Sanity check command when resuming mission in Auto ------------------------------------------------------------------ Copter 3.5-rc6 15-May-2017 Changes from 3.5-rc5 1) Bug fixes and minor enhancements: a) ESC calibration fix when not using safety switch (was waiting for safety switch to be pushed) b) Parameter loading improvements (responds sooner after startup, counts parameters in separate thread) c) Pilot radio passthrough fix for tradheli, single copter, coax copter ------------------------------------------------------------------ Copter 3.5-rc5 03-May-2017 Changes from 3.5-rc4 1) Intel Aero RTF support 2) Smart battery fetches serial number, temperature and individual cell voltages 3) Vehicle heads towards target point instead of next waypoint during straight line waypoint mission commands in AUTO 4) Visual Odometry supported using VISION_POSITION_DELTA mavlink message 5) Do-Set-Home sets EKF origin allowing user to specify vehicle starting position without GPS 6) Object avoidance parameter (AVOID_MARGIN) allows configuring distance to maintain from objects 7) Motor output can be duplicated to multiple channels 8) IRLock can be connected to any I2C bus 9) Piksi "Multi" GPS support 10) Performance Improvements: a) inter-EKF scheduling cooperation (improves load balancing when using multiple EKFs) b) parameter requests from GCS processed asynchronously (resolves bad flight behaviour when fetching params in-flight) c) display performance improvements 1) Bug fixes including: a) LSM303D (Pixhawk's backup IMU) timing fixes b) auxiliary PWM outputs update even when RC input stops c) dataflash log over mavlink fixes d) EKF recovery from severe errors e) reduce twitch when transitioning from spline to straight line waypoints in AUTO f) enable motors after initialisation completes (resolves some BLHeli ESC initialisation and calibration issues) ------------------------------------------------------------------ Copter 3.5-rc4 08-Apr-2017 Changes from 3.5-rc3 1) Bug fixes including: a) Baro based altitude estimate fixes including limiting ground temperature to reasonable value b) Fix 0.6ms lag reduction c) Fix Invensense IMU driver temperature reading d) Fix semaphore take during interrupts that may have caused very occasional main loop rate issues e) Return Home if GCS asks for first (i.e. zero-ith) mission command (required for Solo) ------------------------------------------------------------------ Copter 3.5-rc3 24-Mar-2017 Changes from 3.5-rc2 1) OLED Display fixes: a) can be connected to either I2C bus b) last character on line correctly cleared 2) bug fix to detect SBUS failsafe on Pixracer 3) bug fix to Gimbal servo reversing 4) ensure WPNAV_LOIT_SPEED is non-zero to avoid divide-by-zero 5) Fence pre-arm check failure messages clarified ------------------------------------------------------------------ Copter 3.5-rc2 13-Mar-2017 Changes from 3.5-rc1 1) Improved dual GPS support including blending (set GPS_TYPE2=1, GPS_AUTO_SWITCH=2) 2) AutoTune with position hold (enter AutoTune from Loiter or PosHold modes to enable light position hold) 3) New boards/drivers: a) PixhawkMini support b) AUAV2.1 board support (for AUAV2.1 set BRD_TYPE to 20 to distinguish from PixhawkMini) c) Garmin LidarLiteV3 support d) Maxell Smart Battery support e) Invensense ICM-20602 IMU and ST L3GD20H gyro drivers added 4) IMU to Motor lag reduced by 0.6ms 5) Object Avoidance: a) support TeraRanger Tower sensor b) support using normal (1-dimensional lidar/sonar) 6) Minor changes/enhancements: a) add MOT_SPOOL_TIME parameter to allow users to control spool-up time of motors b) remove Solo gimbal from -v2 because of 1MB Flash limit on many Pixhawk1s c) altitude check for Guided mode takeoff (must be at least 1m) d) auxiliary switch to arm/disarm vehicle (set CH7_OPT to 41) e) change battery alarm tone to reduce impact on IMU f) add battery monitor health reporting g) support DO-FENCE-ENABLE mission command to enable/disable fence during missions 7) Bug Fixes: a) OLED Display clears messages after 10seconds b) Servo Gimbal output range fix (could attempt to push servos beyond their limits) c) fix do-set-servo d) fix dataflash log time (was always appearing as 1970) ------------------------------------------------------------------ Copter 3.5-rc1 28-Jan-2017 Changes from 3.4.4 1) Multicopter firmware consolidated into single binary, users must set FRAME_CLASS parameter (1:Quad, 2:Hexa, 3:Octa, 4:OctaQuad, 5:Y6, 7:Tri) 2) PixRacer specific items: a) board LEDs supported b) ESC calibration start problem resolved (was sometimes not detecting high throttle from pilot) 3) Relaxed compass calibration and compass consistency checks 4) Sensor and Optional Hardware Improvements: a) IMU sampling rate for MPU9250, ICM20608 IMUs to 8kHz for improved vibration resistance (Pixracer, Pixhawk2) b) Onboard Display (http://ardupilot.org/copter/docs/common-display-onboard.html) c) Here+ RTK GPS (UBlox M8P RTK) support d) LightWare I2C drivers usable on Copter (thanks to in-tree drivers below) e) MaxBotix sonar with serial interface now supported f) Bebop optical flow (but sonar not yet operational making this feature currently impossible to use) 5) Precision Loiter using IRLock sensor (set CH7_OPT to 39) 6) Delivery improvements: a) Servo gripper (http://ardupilot.org/copter/docs/common-gripper-servo.html) b) Package_Place mission command (drops package without vehicle landing) 7) Pozyx support for Non-GPS flight (http://ardupilot.org/copter/docs/common-pozyx.html) 8) EKF improvements: a) improved blending of optical flow and GPS b) EKF3 added in ride-along. Enable by setting EK3_ENABLE=1 c) improvements when using range finder as primary height reference 9) Object Avoidance improvements (http://ardupilot.org/dev/docs/code-overview-object-avoidance.html): a) uses mini-fence b) accepts MAVLink distance-sensor messages c) simple avoidance in AltHold mode 10) Other improvements: a) pre-arm check that logging is working b) better reporting of battery failsafe to ground stations c) reduced minimum waypoint speed to 20cm/s d) Flight time recorder (http://ardupilot.org/copter/docs/common-flight-time-recorder.html) e) UBlox GPS baud rate fix (was occasionally selecting wrong rate) 11) Technical improvements (users may not see a functional change): a) in-tree drivers lead to improved sharing of drivers with Linux boards b) copter arming checks consolidated with other vehicles ------------------------------------------------------------------ Copter 3.4.6 15-Mar-2017 Changes from 3.4.5 1) ensure WPNAV_LOIT_SPEED is non-zero to avoid divide-by-zero ------------------------------------------------------------------ Copter 3.4.5 11-Feb-2017 Changes from 3.4.4 1) Bug fix to Guided mode that could lead to crash after take-off completes if MOT_THST_HOVER too high ------------------------------------------------------------------ Copter 3.4.4 06-Jan-2017 / Copter 3.4.4-rc1 21-Dec-2016 Changes from 3.4.3 1) Bug Fixes / Minor Enhancements: a) prevent unwanted EKF core switching at startup b) helicopter prevented from taking off in position hold mode before rotors at full speed c) battery resistance calculations fixed d) avoid unnecessary parameter change notifications to ground station e) default power module definitions for Navio boards f) on-board compass calibration capability bit added (tells ground stations that onboard calibration is supported) ------------------------------------------------------------------ Copter 3.4.3 08-Dec-2016 / Copter 3.4.3-rc1 01-Dec-2016 Changes from 3.4.2 1) Bug Fixes: a) reduce unnecessary EKF core switching and fix position reset b) attitude control does not limit rate if ATC_ACCEL_MAX is zero c) ignore arm command from GCS if already armed d) set land-complete to false during auto takeoff e) onboard compass calibration memory init fix that could lead to failure to complete 2) Minor Improvements: a) LeddarOne driver robustness improvements b) allow MOT_THR_MIX_MAX to be as high as 2.0 c) uavcan bus settle time increased to 2sec d) helicopters do not hold position during auto takeoff until rotor is at full speed ------------------------------------------------------------------ Copter 3.4.2 16-Nov-2016 / Copter 3.4.2-rc1/rc2 07-Nov-2016 Changes from 3.4.1 1) Minor Improvements: a) ACRO_Y_EXPO applies to all flight modes (but is defaulted to zero) b) Autotune timeout increased (helps with large copters) c) AltHold filter applied to P (was previously only for D) d) arming check for compass health (was previously only a pre-arm check) 2) Bug Fixes: a) compass calibration (onboard) fix to return completion status b) LeddarOne driver busy-wait fix c) SBF GPS altitude and accuracy reporting fix d) MAV GPS uses existing configured baud rate instead of auto detecting ------------------------------------------------------------------ Copter 3.4.1 01-Nov-2016 Changes from 3.4.0 1) Pixracer PPM RC input fix ------------------------------------------------------------------ Copter 3.4.0 31-Oct-2016 Changes from 3.4.0-rc7 1) Disabled LeddarOne driver (will be fixed in AC3.4.1 within a couple of weeks) ------------------------------------------------------------------ Copter 3.4.0-rc7 25-Oct-2016 Changes from 3.4.0-rc6 1) Bug fixes, minor improvements: a) more DSM binding fixes for pixracer b) allow non-motor channels to move before safety switch is pressed c) fix Bebop motor order d) fix MAVLink system id for first few messages e) fix throw mode throttle while rotating to level ------------------------------------------------------------------ Copter 3.4.0-rc6 15-Oct-2016 Changes from 3.4.0-rc5 1) Object Avoidance with SF40c 360 lidar 2) ACRO_Y_EXPO parameter allows exponential yaw in ACRO mode (slow yaw at mid stick but fast response at full stick) 3) ACRO_THR_MID parameter allows custom mid throttle for ACRO mode 4) Precision Landing reliability and accuracy improvements using mini EKF and adding IRLock lens distortion correction 5) Bug fixes, minor improvements: a) fix DSM binding on Pixracer b) resolved position jump caused by EKF core change (also added logging and reporting to GCS) c) EKF failsafe while in LAND triggers non-GPS LAND d) small throttle jump removed when switching between AltHold, Loiter 6) Safety: a) EKF falls back to optical flow if GPS fails b) pre-arm check that GPS configuration has completed ------------------------------------------------------------------ Copter 3.4.0-rc5 14-Sep-2016 Changes from 3.4.0-rc4 1) Sprayer enabled by default 2) Bug fixes, minor improvements: a) EKF fix for yaw angle reset fix when switching between cores (AC3.4 runs multiple EKFs simultaneously) b) EKF fixes when fusing range finder into height estimate c) pixracer clone board IMU hardware issue work around d) dataflash time-going-backwards fix e) fix rate PID conversion (AC3.3->AC3.4) for single, coax and tricopters ------------------------------------------------------------------ Copter 3.4.0-rc4 06-Sep-2016 Changes from 3.4.0-rc3 1) Intel Aero flight controller support (not Intel Aero RTF, that was done in a later release) 2) Bug fixes, minor improvements: a) resolve unlikely endless-climb in AltHold, Loiter by ensuring Z-axis accelerometer IMAX can always overpower hover throttle b) fix auto build issue that could lead to parameter corruption c) fix EKF2 gyro estimation error when switching between IMUs d) sanity check MOT_THST_MIX_MIN, MAX parameters e) increase likelihood that parachute will release by reducing counter instead of resetting counter if vehicle becomes temporarily upright ------------------------------------------------------------------ Copter 3.4.0-rc3 31-Aug-2016 Changes from 3.4.0-rc2 1) Landing detector improvements: a) checks that descent rate is less than 1m/s (avoids disarms when vehicle is obviously still descending) b) tradheli fix for landing detector 2) WP_NAVALT_MIN parameter limits maximum lean angle when vehicle is below the specified alt while taking off or landing. Only applies in LAND mode, final stage of RTL and during take-off in AUTO mode 3) GND_EFFECT_COMP parameter allows turning on EKF compensation for ground effect during take-off and landing 4) Advanced Failsafe for use in OutBack challenge (see http://ardupilot.org/plane/docs/advanced-failsafe-configuration.html) 5) AutoTune minor improvement to reduce step size on vehicles with very low hover throttle (i.e. high power-to-weight ratio) 6) Bug fixes, minor improvement: a) OneShot ESC calibration fix b) LAND_SPEED_HIGH allows specifying vertical descent speed separate from WPNAV_SPEED_DN during the initial descent in LAND mode (and final stage of RTL) c) improved USB driver reliability for windows users (NuttX change) d) report dataflash logging health to ground station e) Guided mode accepts yaw rate from SET_ATTITUDE_TARGET message ------------------------------------------------------------------ Copter 3.4.0-rc2 08-Aug-2016 Changes from 3.4.0-rc1 1) ADSB based avoidance of manned aircraft 2) Polygon fence (works seamlessly with circular and altitude fences) 3) Throttle related changes: a) motors speed feedback to pilot while landed - motors only spin up to minimum throttle as throttle stick is brought to mid (previously spun up to 25%) b) MOT_HOVER_LEARN allows MOT_THST_HOVER to be learned in flight c) THR_MIN becomes MOT_SPIN_MIN d) THR_MID becomes MOT_THST_HOVER 4) Precision landing: a) control improved by reducing lag from sensor and correcting math errors b) descent rate slows to allow time to correct horizontal position error 5) Guided mode: a) velocity controller accelerates/decelerates smoothly to target b) Guided_NoGPS flight mode added to allow companion computer control in non-GPS environments c) stop at fence if using velocity controller, reject points outside fence if using position controller 6) Throw Mode: a) THROW_NEXTMODE parameter allows copter to switch to Auto, Guided, RTL, Land or Brake after throw is complete b) Throw mode fixes so motors reliably start 7) Attitude controller: a) use Quaternions instead of Euler angles b) ATC_ANG_LIM_TC allows controlling rate at which lean angles are limited to preserve altitude in AltHold, Loiter 8) EKF can use range finder as primary height source if EKF2_RNG_USE_HGT parameter is set to 70 9) Bug fixes a) AutoTune fix so that gains don't fall too low b) Rally points with altitudes no longer cause vehicle to climb above fence during RTL c) various EKF fixes including bug in initialisation of declination co-variances d) SingleCopter, CoaxCopter flag gains 10) Small enhancements: a) Rally points outside fence are ignored b) AP_Button support added to allow ground station to see if user has pushed a button on the flight controller c) support for PLAY_TUNE and LED_CONTROL mavlink messages to cause vehicle to play tune or change colour of LED d) support for GPS_INPUT mavlink message to allow supplying vehicle position data from other sources e) NAV_DELAY mission command to delay start of mission (or individual command) until a specified absolute time e) TKOFF_NAV_ALT param allows take-off with no horizontal position hold until vehicle reaches specified altitude (intended mostly for helicopters) f) SCHED_LOOP_RATE param allows slowing main loop rate from default of 400 (intended for developers only) 11) Safety (in addition to Fence improvements above): a) Motors begin spinning 2 seconds after arming (previously motors spun immediately) ------------------------------------------------------------------ Copter 3.4.0-rc1 28-May-2016 Changes from 3.3.3 1) EKF2 allows "boat mode" (attitude initialisation without gyro calibration) 2) Throw mode 3) Terrain following: a) support terrain altitudes during missions using GCS's map data or rangefinder (i.e. Lidar) b) LightWare range finder driver fixes (I2C works) c) Bebop sonar support 4) Precision Landing using IRLock sensor 5) Attitude controller re-organisation (all parameter changes automatically moved and scales adjusted) a) RATE_ parameters become ATC_RAT_ (i.e. RATE_RLL_P becomes ATC_RAT_RLL_P) b) Rate Roll, Pitch, Yaw P, D are reduced by 10% for X, V, H frames, increased by 27% for all other frames c) STB_ parameters becomes ATC_ANG_ (i.e. STB_RLL_P becomes ATC_ANG_RLL_P) 6) Motors library improvements: a) support OneShot ESCs (set MOT_PWM_TYPE to 0 for Normal, 1 for OneShot or 2 for OneShot125) b) TriCopter compensates for tail servo angle c) SingleCopter, CoaxCopter adjust control surfaces based on throttle output d) MOT_PWM_MIN, MAX allow specifying output ranges to ESCs which are difference from throttle input channel (i.e. RC3) e) TradHeli servo objects moved into heli class (HSV_ parameters become H_SV_) 7) uAvionix Ping sensor support (ADS-B vehicles appear on GCS, avoidance will come in future release) 8) Safety: a) warning if GPS update rate is slow (under 5hz, does not stop arming) ------------------------------------------------------------------ Copter 3.3.3 24-Feb-2016 / 3.3.3-rc2 27-Jan-2016 Changes from 3.3.3-rc1 1) bug fix to Guided mode's velocity controller to run at 400hz 2) bug fix to MAVLink routing to allow camera messages to reach MAVLink enabled cameras and gimbals (including SToRM32) ------------------------------------------------------------------ Copter 3.3.3-rc1 4-Jan-2016 Changes from 3.3.2 1) Restrict mode changes in helicopter when rotor is not at speed 2) add ATC_ANGLE_BOOST param to allow disabling angle boost for all flight modes 3) add LightWare range finder support ------------------------------------------------------------------ Copter 3.3.2 01-Dec-2015 / 3.3.2-rc2 18-Nov-2015 Changes from 3.3.2-rc1 1) Bug fix for desired climb rate initialisation that could lead to drop when entering AltHold, Loiter, PosHold 2) Fix to hard landings when WPNAV_SPEED_DN set high in RTL, Auto (resolved by using non-feedforward alt hold) 3) Reduce Bad AHRS by filtering innovations 4) Allow arming without GPS if using Optical Flow 5) Smoother throttle output in Guided mode's velocity control (z-axis now 400hz) ------------------------------------------------------------------ Copter 3.3.2-rc1 4-Nov-2015 Changes from 3.3.1 1) Helicopter Improvements: a) Fix Arming race condition b) Fix servos to move after arming in Stabilize and Acro c) Implement Pirouette Compensation d) Add Rate I-Leak-Min functionality e) Add new Stab Collective and Acro Expo Col functions f) Add circular swashplate limits (Cyclic Ring) g) Add new H_SV_Man functions h) Add Hover Roll Trim function i) Add Engine Run Enable Aux Channel function j) Add servo boot test function h) Add Disarm Delay parameter ------------------------------------------------------------------ Copter 3.3.1 26-Oct-2015 / 3.3.1-rc1 20-Oct-2015 Changes from 3.3 1) Bug fix to prevent potential crash if Follow-Me is used after an aborted takeoff 2) compiler upgraded to 4.9.3 (runs slightly faster than 4.7.2 which was used previously) ------------------------------------------------------------------ Copter 3.3 29-Sep-2015 / 3.3-rc12 22-Sep-2015 Changes from 3.3-rc11 1) EKF recovers from pre-arm "Compass variance" failure if compasses are consistent ------------------------------------------------------------------ Copter 3.3-rc11 10-Sep-2015 Changes from 3.3-rc10 1) PreArm "Need 3D Fix" message replaced with detailed reason from EKF ------------------------------------------------------------------ Copter 3.3-rc10 28-Aug-2015 Changes from 3.3-rc9 1) EKF improvements: a) simpler optical flow takeoff check 2) Bug Fixes/Minor enhancements: a) fix INS3_USE parameter eeprom location b) fix SToRM32 serial protocol driver to work with recent versions c) increase motor pwm->thrust conversion (aka MOT_THST_EXPO) to 0.65 (was 0.50) d) Firmware version sent to GCS in AUTOPILOT_VERSION message 3) Safety: a) pre-arm check of compass variance if arming in Loiter, PosHold, Guided b) always check GPS before arming in Loiter (previously could be disabled if ARMING_CHECK=0) c) sanity check locations received from GCS for follow-me, do-set-home, do-set-ROI d) fix optical flow failsafe (was not always triggering LAND when optical flow failed) e) failsafe RTL vs LAND decision based on hardcoded 5m from home check (previously used WPNAV_RADIUS parameter) ------------------------------------------------------------------ Copter 3.3-rc9 19-Aug-2015 Changes from 3.3-rc8 1) EKF improvements: a) IMU weighting based on vibration levels (previously used accel clipping) b) fix blended acceleration (used for altitude control) in cases where first IMU fails c) ensure unhealthy barometer values are never consumed 2) TradHeli: remove acceleration feed forward 3) Safety: a) check accel, gyro and baro are healthy when arming (previously was only checked pre-arm) b) Guided mode velocity controller timeout (vehicle stops) after 3 seconds with no update from GCS 4) Minor enhancements: a) fix for AUAV board's usb-connected detection b) add Lidar-Lite-V2 support c) MOT_THR_MIN_MAX param added to control prioritisation of throttle vs attitude during dynamic flight d) RALLY_INCL_HOME param allows always including home when using rally points e) DO_FLIGHT_TERMINATION message from GCS acts as kill switch 5) Bug Fixes: a) fix to ensure motors start slowly on 2nd spin-up b) fix RTL_CLIMB_MIN feature (vehicle climbed too high above home) ------------------------------------------------------------------ Copter 3.3-rc8 25-Jul-2015 Changes from 3.3-rc7 1) EKF improvements: a) de-weight accelerometers that are clipping to improve resistance to high vibration b) fix EKF to use primary compass instead of first compass (normally the same) 2) UBlox "HDOP" corrected to actually be hdop (was pdop) which leads to 40% lower value reported 3) TradHeli: a) Motors library split into "Multicopter" and "TradHeli" so TradHeli does not see multicopter parameters b) Heading target reset during landing to reduce vehicle fighting to rotate while on the ground 4) Minor enhancements: a) SToRM32 gimbal can be connected to any serial port b) log when baro, compass become unhealthy c) ESC_CALIBRATION parameter can be set to "9" to disable esc calibration startup check d) Circle rate adjustment with ch6 takes effect immediately e) log home and origin f) pre-arm check of battery voltage and fence g) RTL_CLIMB_MIN parameter forces vehicle to climb at least this many cm when RTL is engaged (default is zero) 5) Bug fixes: a) fix THR_MIN being incorrectly scaled as pwm value during low-throttle check b) fence distance calculated from home (was incorrectly calculated from ekf-origin) c) When flying with joystick and joystick is disconnected, control returns immediately to regular TX d) dataflash's ATT yaw fixed to report heading as 0 ~ 360 e) fix to mission's first command being run multiple times during mission if it was a do-command f) ekf-check is enabled only after ekf-origin is set (stops red-yellow flashing led when flying without GPS lock) g) fix initialisation of mount's mode h) start-up logging so parameters only logged once, mission always written 6) Linux: a) bebop support ------------------------------------------------------------------ Copter 3.3-rc7 28-Jun-2015 Changes from 3.3-rc6 1) reduce EKF gyro bias uncertainty that caused attitude estimate errors 2) force 400hz IMU logging on (temporary for release candidate testing) ------------------------------------------------------------------ Copter 3.3-rc6 25-Jun-2015 Changes from 3.3-rc5 1) EKF related changes: a) reset altitude even when arming without GPS lock b) fix yaw twitch caused by EKF heading estimate reset c) fix IMU time scaling bug that caused height estimate to deviate from the baro 2) AutoTune improvements: a) improved yaw tuning by increasing yaw step magnitude b) added logging of accelerations c) improvements to step tests 3) Improved crash check: a) allow triggering even if pilot doesn't move throttle to zero b) easier triggering by removing baro check and using angle error instead of absolute tilt angle 4) TradHeli: a) swash moves while landed in AltHold mode b) improvements to land detector c) fixed RSC Runup Time calculation d) Rate FF Low-pass Filter changed from 5Hz to 10Hz, more responsive 5) support Linux builds for NAVIO+ and Erle-Brain (http://firmware.diydrones.com/Copter/beta/) 6) Other improvements / Bug Fixes: a) sonar pre-arm checks only enforced if using optical flow b) fix EKF failsafe bug that would not allow recovery c) full rate IMU logging for improved vibration analysis (set LOG_BITMASK to All+FullIMU) d) new VIBE dataflash message records vibration levels e) default MNT_TYPE to "1" if servo gimbal rc outputs were defined f) RC_FEEL defaults to medium g) addition of SToRM32 serial support (supports mount angle feedback to GCS) h) new tricopter's tail servo parameters (MOT_YAW_SV_MIN, MAX, TRIM, REV) ------------------------------------------------------------------ Copter 3.3-rc5 23-May-2015 Changes from 3.3-rc4 1) Fix AHRS bad gyro health message caused by timing jitter and log IMU health 2) TradHeli: a) better default rate PIDs b) Collective pitch output now operates even when disarmed 3) Small changes/fixes: a) GCS can use MAV_CMD_MISSION_START to start mission in AUTO even without pilot raising throttle b) GCS can force disarming even in flight by setting param2 to "21196" c) rc-override timeout reduced from 2 seconds to 1 (applies when using GCS joysticks to control vehicle) d) do-set-speed fix so it takes effect immediately during missions e) GCS failsafe disarms vehicle if already landed (previously it could RTL) ------------------------------------------------------------------ Copter 3.3-rc4 17-May-2015 Changes from 3.3-rc3 1) AutoTune: a) save roll, pitch, yaw rate acceleration limits along with gains b) more conservative gains 2) Roll, pitch rate control feed-forward now on by default (set ATC_RATE_FF_ENAB to "0" to disable) 3) Serial ports increased to maximum of 4 (set SERIALX_PROTOCOL to 1) 4) MOT_THR_MIX_MIN param to control minimum throttle vs attitude during landing (higher = more attitude control but bumpier landing) 5) EKF fixes/improvements a) prevent yaw errors during fast spins b) bug fix preventing external selection of optical flow mode 6) Parachute: a) servo/relay held open for 2sec when deploying (was 1sec) b) fix altitude check to be alt-above-home (was alt-above ekf origin which could be slightly different) 7) TradHeli: a) parameters moved to stop possibility of corruption if board is switched between tradheli and multicopter firmware. Heli users may need to re-setup some heli-specific params. b) H_COLYAW param can be float 8) Small Improvements / Bug Fixes: a) reduced spline overshoot after very long track followed by very short track b) log entire mission to dataflash whenever it's uploaded c) altitude reported if vehicle takes off before GPS lock d) high speed logging of IMU e) STOP flight mode renamed to BRAKE and aux switch option added ------------------------------------------------------------------ Copter 3.3-rc2/rc3 02-May-2015 Changes from 3.3-rc1 1) AutoTune reliability fixes (improved filtering to reduce noise interference) 2) Optical flow improvements: a) Range Finder pre-arm check - lift vehicle between 50cm ~ 2m before arming. Can be disabled by setting ARMING_CHECK to "Skip Params/Sonar" b) Vehicle altitude limited to range finder altitude when optical flow is enabled 3) AltHold & Take-off changes: a) feed-forward controller and jerk limiting should result in slightly snappier performance and smoother take-offs b) vehicle climbs automatically to PILOT_TKOFF_ALT alt when taking off in Loiter, AltHold, PosHold, Sport (disabled by default, pilot's throttle input overrides takeoff) c) PILOT_THR_FILT allows enforcing smoother throttle response in manual flight modes (defaults to 0 = off) d) TX with sprung throttle can set PILOT_THR_BHV to "1" so motor feedback when landed starts from mid-stick instead of bottom of stick e) GCS can initiate takeoff even in Loiter, AltHold, PosHold and sport by issuing NAV_TAKEOFF mavlink command 4) Stop flight mode - causes vehicle to stop quickly, and does not respond to user input or waypoint movement via MAVLink. Requires GPS, will be renamed to Brake mode. 5) Aux channel features: a) Emergency Stop - stops all motors immediately and disarms in 5 seconds b) Motor Interlock - opposite of Emergency Stop, must be on to allow motors to spin motors, must be off to arm 6) Air pressure gain scaling (of roll, pitch, yaw) should mostly remove need to re-tune when flying at very different altitudes 7) landing detector simplified to only check vehicle is not accelerating & motors have hit their lower limit 8) Loiter tuning params to remove "freight train" stops: raising WPNAV_LOIT_MAXA makes vehicle start and stop faster raising WPNAV_LOIT_MINA makes vehicle stop more quickly when sticks centered 9) Other items: a) faster EKF startup b) Camera control messages sent via MAVLink to smart cameras. Allow control of camera zoom for upcoming IntelEdison/Sony QX1 camera control board c) Lost Copter Alarm can be triggered by holding throttle down, roll right, pitch back 10) Bug fixes: a) Home position set to latest arm position (it was being set to previous disarm location or first GPS lock position) b) bug fix to mission Jump to command zero ------------------------------------------------------------------ Copter 3.3-rc1 11-Apr-2015 Changes from 3.2.1 1) Only support fast CPUs boards (Pixhawk, VRBrain, etc) and drop support for APM1, APM2 (sorry!) 2) AutoTune for yaw 3) Smooth throttle curve which should reduce wobbles during fast climbs and descents 4) ch7/ch8 aux switches expanded to ch9 ~ ch12 (see CH9_OPT ~ CH12_OPT params) 5) PX4Flow support in Loiter mode (still somewhat experimental) 6) Safety features: a) EKF on by default replacing DCM/InertialNav which should improve robustness b) increased accelerometer range from 8G to 16G to reduce chance of climb due to high vibrations (requires accel calibration) 7) Landing features: a) improved landing on slopes b) retractable landing gear (see LGR_ parameters) 8) Camera Gimbal features: a) SToRM32 gimbal support (using MAVLink) b) AlexMos gimbal support (using AlexMos serial interface) c) do-mount-control commands supported in missions (allows controlling gimbal angle in missions) 9) Battery related features: a) PID scaling for battery voltage (disabled by default, see MOT_THST_BAT_ parameters) b) smart battery support 10) Other: a) support do-set-home command (allows return-to-me and locked home position once GCS enhancements are completed) b) performance improvements for Pixhawk reduce CPU load from 80% to 15% c) firmware string name changed from ArduCopter to APM:Copter ------------------------------------------------------------------ ArduCopter 3.2.1 11-Feb-2015 / 3.2.1-rc2 30-Jan-2015 Changes from 3.2.1-rc1 1) Bug Fixes: a) prevent infinite loop with linked jump commands b) Pixhawk memory corruption fix when connecting via USB c) vehicle stops at fence altitude limit in Loiter, AltHold, PosHold d) protect against multiple arming messages from GCS causing silent gyro calibration failure ------------------------------------------------------------------ ArduCopter 3.2.1-rc1 08-Jan-2015 Changes from 3.2 1) Enhancements: a) reduced twitch when passing Spline waypoints b) Faster disarm after landing in Auto, Land, RTL c) Pixhawk LED turns green before arming only after GPS HDOP falls below 2.3 (only in flight modes requiring GPS) 2) Safety Features: a) Add desired descent rate check to reduce chance of false-positive on landing check b) improved MPU6k health monitoring and re-configuration in case of in-flight failure c) Rally point distance check reduced to 300m (reduces chance of RTL to far away forgotten Rally point) d) auto-disarm if vehicle is landed for 15seconds even in Auto, Guided, RTL, Circle e) fence breach while vehicle is landed causes vehicle to disarm (previously did RTL) 3) Bug Fixes: a) Check flight mode even when arming from GCS (previously it was possible to arm in RTL mode if arming was initiated from GCS) b) Send vehicle target destination in RTL, Guided (allows GCS to show where vehicle is flying to in these modes) c) PosHold wind compensation fix ------------------------------------------------------------------ ArduCopter 3.2 07-Nov2014 / 3.2-rc14 31-Oct-2014 Changes from 3.2-rc13 1) Safety Features: a) fail to arm if second gyro calibration fails (can be disabled with ARMING_CHECK) 2) Bug fixes: a) DCM-check to require one continuous second of bad heading before triggering LAND b) I2C bug that could lead to Pixhawk freezing up if I2C bus is noisy c) reset DCM and EKF gyro bias estimates after gyro calibration (DCM heading could drift after takeoff due to sudden change in gyro values) d) use primary GPS for LED status (instead of always using first GPS) ------------------------------------------------------------------ ArduCopter 3.2-rc13 23-Oct-2014 Changes from 3.2-rc12 1) DCM check triggers LAND if yaw disagrees with GPS by > 60deg (configure with DCM_CHECK_THRESH param) and in Loiter, PosHold, Auto, etc 2) Safety features: a) landing detector checks baro climbrate between -1.5 ~ +1.5 m/s b) sanity check AHRS_RP_P and AHRS_YAW_P are never less than 0.05 c) check set-mode requests from GCS are for this vehicle 3) Bug fixes: a) fix ch6 tuning of wp-speed (was getting stuck at zero) b) parachute servo set to off position on startup c) Auto Takeoff timing bug fix that could cause severe lean on takeoff d) timer fix for "slow start" of motors on Pixhawk (timer was incorrectly based on 100hz APM2 main loop speed) 4) reduced number of relays from 4 to 2 (saves memory and flash required on APM boards) 5) reduced number of range finders from 2 to 1 (saves memory and flash on APM boards) 6) allow logging from startup when LOG_BITMASK set to "All+DisarmedLogging" ------------------------------------------------------------------ ArduCopter 3.2-rc12 10-Oct-2014 Changes from 3.2-rc11 1) disable sonar on APM1 and TradHeli (APM1 & APM2) to allow code to fit 2) Add pre-arm and health check that gyro calibration succeeded 3) Bug fix to EKF reporting invalid position and velocity when switched on in flight with Ch7/Ch8 switch ------------------------------------------------------------------ ArduCopter 3.2-rc11 06-Oct-2014 Changes from 3.2-rc10 1) reduce lean on take-off in Auto by resetting horizontal position targets 2) TradHeli landing check ignores overall throttle output 3) reduce AHRS bad messages by delaying 20sec after init to allow EKF to settle (Pixhawk only) 4) Bug fixes: a) fix THR_MIN scaling issue that could cause landing-detector to fail to detect landing when ch3 min~max > 1000 pwm b) fix Mediatek GPS configuration so update rate is set correctly to 5hz c) fix to Condition-Yaw mission command to support relative angles d) EKF bug fixes when recovering from GPS glitches (affects only Pixhawks using EKF) ------------------------------------------------------------------ ArduCopter 3.2-rc10 24-Sep-2014 Changes from 3.2-rc9 1) two-stage land-detector to reduce motor run-up when landing in Loiter, PosHold, RTL, Auto 2) Allow passthrough from input to output of channels 9 ~ 14 (thanks Emile!) 3) Add 4hz filter to vertical velocity error during AltHold 4) Safety Feature: a) increase Alt Disparity pre-arm check threshold to 2m (was 1m) b) reset battery failsafe after disarming/arming (thanks AndKe!) c) EKF only apply centrifugal corrections when GPS has at least 6 satellites (Pixhawk with EKF enabled only) 5) Bug fixes: a) to default compass devid to zero when no compass connected b) reduce motor run-up while landing in RTL ------------------------------------------------------------------ ArduCopter 3.2-rc9 11-Sep-2014 Changes from 3.2-rc8 1) FRAM bug fix that could stop Mission or Parameter changes from being saved (Pixhawk, VRBrain only) ------------------------------------------------------------------ ArduCopter 3.2-rc8 11-Sep-2014 Changes from 3.2-rc7 1) EKF reduced ripple to resolve copter motor pulsing 2) Default Param changes: a) AltHold Rate P reduced from 6 to 5 b) AltHold Accel P reduced from 0.75 to 0.5, I from 1.5 to 1.0 c) EKF check threshold increased from 0.6 to 0.8 to reduce false positives 3) sensor health flags sent to GCS only after initialisation to remove false alerts 4) suppress bad terrain data alerts 5) Bug Fix: a)PX4 dataflash RAM usage reduced to 8k so it works again ------------------------------------------------------------------ ArduCopter 3.2-rc7 04-Sep-2014 Changes from 3.2-rc6 1) Safety Items: a) Landing check made more strict (climb rate requirement reduced to 30cm/s, overall throttle < 25%, rotation < 20deg/sec) b) pre-arm check that accels are consistent (Pixhawk only, must be within 1m/sec/sec of each other) c) pre-arm check that gyros are consistent (Pixhawk only, must be within 20deg/sec of each other) d) report health of all accels and gyros (not just primary) to ground station ------------------------------------------------------------------ ArduCopter 3.2-rc6 31-Aug-2014 Changes from 3.2-rc5 1) Spline twitch when passing through a waypoint largely resolved 2) THR_DZ param added to allow user configuration of throttle deadzone during AltHold, Loiter, PosHold 3) Landing check made more strict (climb rate must be -40~40cm/s for 1 full second) 4) LAND_REPOSITION param default set to 1 5) TradHeli with flybar passes through pilot inputs directly to swash when in ACRO mode 6) Safety Items: a) EKF check disabled when using inertial nav (caused too many false positives) b) pre-arm check of internal vs external compass direction (must be within 45deg of each other) 7) Bug Fixes: a) resolve NaN in angle targets when vehicle hits gimbal lock in ACRO mode b) resolve GPS driver buffer overflow that could lead to missed GPS messages on Pixhawk/PX4 boards c) resolve false "compass not calibrated" warnings on Pixhawk/PX4 caused by missing device id initialisation ------------------------------------------------------------------ ArduCopter 3.2-rc5 15-Aug-2014 Changes from 3.2-rc4 1) Pixhawk's max num waypoints increased to 718 2) Smoother take-off in AltHold, Loiter, PosHold (including removing initial 20cm jump when taking off) 3) ACRO mode roll, pitch, yaw EXPO added for faster rotation when sticks are at extremes (see ACRO_EXPO parameter) 4) ch7/ch8 relay option replaces ch6 option (ch6 is reserved for tuning not switching things on/off) 5) Safety Items: a) Baro glitch check relaxed to 5m distance, 15m/s/s max acceleration b) EKF/INav check relaxed to 80cm/s/s acceleration correct (default remains as 0.6 but this now means 80cm/s/s) c) When GPS or Baro glitch clears, the inertial nav velocities are *not* reset reducing chance of sudden vehicle lean d) Baro altitude calculation checked for divide-by-zero and infinity 6) Bug Fixes: a) AltHold jump bug fixed (altitude target reset when landed) b) Rally point bug fix so it does not climb excessively before flying to rally point c) body-frame rate controller z-axis bug fix (fast rotation in z-axis would cause wobble in roll, pitch) ------------------------------------------------------------------ ArduCopter 3.2-rc4 01-Aug-2014 Changes from 3.2-rc3 1) Pre-takeoff throttle feedback in AltHold, Loiter, PosHold 2) Terrain altitude retrieval from ground station (informational purposes only so far, Pixhawk only) 3) Safety Items: a) "EKF check" will switch to LAND mode if EKF's compass or velocity variance over 0.6 (configurable with EKFCHECK_THRESH param) When EKF is not used inertial nav's accelerometer corrections are used as a substitute b) Barometer glitch protection added. BAROGLTCH_DIST and BAROGLTCH_ACCEL parameters control sensitivity similar to GPSGLITCH protection When glitching occurs barometer values are temporarily ignored c) Throttle/radio and battery failsafes now disarm vehicle when landed regardless of pilot's throttle position d) auto-disarm extended to Drift, Sport and OF_Loiter flight modes e) APM2 buzzer notification added for arming failure f) APM2 arming buzz made longer (now matches Pixhawk) g) do-set-servo commands cannot interfere with motor output 4) Bug Fixes: a) Drift slow yaw response fixed b) AC3.2-rc3 failsafe bug resolved. In -rc3 the throttle failsafe could be triggered even when disabled or motors armed (although vehicle would not takeoff) ------------------------------------------------------------------ ArduCopter 3.2-rc3 16-Jul-2014 Changes from 3.2-rc2 1) Hybrid renamed to PosHold 2) Sonar (analog, i2c) and PulsedLight Range Finders enabled on Pixhawk (Allyson, Tridge) 3) Landing changes: a) disable pilot repositioning while landing in RTL, Auto (set LAND_REPOSITION to 1 to re-enable) (JonathanC) b) delay 4 seconds before landing due to failsafe (JonathanC) 4) Secondary compass calibration enabled, pre-arm check that offsets match current devices (Randy, Tridge, MichaelO) 5) Control improvements: a) use bias adjusted gyro rates - helps in cases of severe gyro drift (Jonathan) b) bug-fixes when feed-forward turned off (Leonard) 6) TradHeli improvements (RobL): a) bug fix to use full collective range in stabilize and acro flight modes b) filter added to main rotor input (ch8) to ensure momentary blip doesn't affect main rotor speed 7) Safety items: a) increased default circular Fence radius to 300m to reduce chance of breach when GPS lock first acquired b) radio failsafe timeout for late frames reduced to 0.5sec for normal receivers or 2.0sec when flying with joystick (Craig) c) accelerometer pre-arm check for all active accelerometers (previously only checked the primary accelerometer) 8) Other features: a) ch7/ch8 option to retract mount (svefro) b) Do-Set-ROI supported in Guided, RTL mode c) Condition-Yaw accepted in Guided, RTL modes (MoussSS) d) CAMERA dataflash message includes relative and absolute altitude (Craig) 9) Red Balloon Popper support (Randy, Leonard): a) Velocity controller added to Guided mode b) NAV_GUIDED mission command added 10) Bug fixes: a) bug fix to flip on take-off in stabilize mode when landing flag cleared slowly (JonathanC) b) allow disarming in AutoTune (JonathanC) c) bug fix to unpredictable behaviour when two spline points placed directly ontop of each other ------------------------------------------------------------------ ArduCopter 3.2-rc2 27-May-2014 Changes from 3.2-rc1 1) Hybrid mode initialisation bug fix 2) Throttle pulsing bug fix on Pixhawk 3) Parachute enabled on Pixhawk 4) Rally Points enabled on Pixhawk ------------------------------------------------------------------ ArduCopter 3.2-rc1 9-May-2014 Changes from 3.1.4 1) Hybrid mode - position hold mode but with direct response to pilot input during repositioning (JulienD, SandroT) 2) Spline waypoints (created by David Dewey, modified and integrated by Leonard, Randy) 3) Drift mode uses "throttle assist" for altitude control (Jason) 4) Extended Kalman Filter for potentially more reliable attitude and position control (Pixhawk only) (Paul Riseborough). Set AHRS_EKF_USE to 1 to enable or use Ch7/8 switch to enable/disable in flight. 5) Manual flight smoothness: a) Smoother roll, pitch response using RC_FEEL_RP parameter (100 = crisp, 0 = extremely soft) b) Adjustable max rotation rate (ATC_RATE_RP_MAX, ATC_RATE_Y_MAX) and acceleration (ATC_ACCEL_RP_MAX, ATC_ACCEL_Y_MAX) 6) Autopilot smoothness: a) Vertical acceleration in AltHold, Loiter, Hybrid modes can be configured with PILOT_ACCEL_Z parameter (higher = faster acceleration) b) Maximum roll and pitch angle acceleration in Loiter mode can be configured with WPNAV_LOIT_JERK (higher = more responsive but potentially jerky) c) Yaw speed can be adjusted with ATC_SLEW_YAW parameter (higher = faster) d) smoother takeoff with configurable acceleration using WPNAV_ACCEL_Z parameter e) Twitches removed during guided mode or when entering Loiter or RTL from high speeds 7) Mission improvements: a) mission will be resumed from last active command when pilot switches out and then back into Auto mode (prev behaviour can be restored by setting MIS_RESTART param to 1) b) DO_SET_ROI persistent across waypoints. All-zero DO_SET_ROI command restores default yaw behaviour c) do-jump fixed d) conditional_distance fixed e) conditional_delay fixed f) do-change-speed command takes effect immediately during mission g) vehicle faces directly at next waypoint (previously it could be about 10deg off) h) loiter turns fix to ensure it will circle around lat/lon point specified in mission command (previously it could be off by CIRCLE_RADIUS) 8) Safety improvements: a) After a fence breach, if the pilot re-takes control he/she will be given a minimum of 10 seconds and 20m to recover before the autopilot will invoke RTL or LAND b) Parachute support including automatic deployment during mechanical failures 9) Other enhancements: a) V-tail quad support b) Dual GPS support (secondary GPS output is simply logged, not actually used yet) c) Electro Permanent Magnet (aka Gripper) support d) Servo pass through for channels 6 ~ 8 (set RC6_FUNCTION to 1) e) Remove 80m limit on RTL's return altitude but never let it be above fence's max altitude 10) Other bug fixes: a) Bug fix for LAND sometimes getting stuck at 10m b) During missions, vehicle will maintain altitude even if WPNAV_SPEED is set above the vehicle's capabilities c) when autopilot controls throttle (i.e. Loiter, Auto, etc) vehicle will reach speeds specified in PILOT_VELZ_MAX and WPNAV_SPEED_UP, WPNAV_SPEED_DN parameters 11) CLI removed from APM1/2 to save flash space, critical functions moved to MAVLink: a) Individual motor tests (see MP's Initial Setup > Optional Hardware > Motor Test) b) compassmot (see MP's Initial Setup > Optional Hardware > Compass/Motor Calib) c) parameter reset to factory defautls (see MP's Config/Tuning > Full Parameter List > Reset to Default) ------------------------------------------------------------------ ArduCopter 3.1.5 27-May-2014 / 3.1.5-rc2 20-May-2014 Changes from 3.1.5-rc1 1) Bug Fix to broken loiter (pixhawk only) 2) Workaround to read from FRAM in 128byte chunks to resolve a few users boot issues (Pixhawk only) ------------------------------------------------------------------ ArduCopter 3.1.5-rc1 14-May-2014 Changes from 3.1.4 1) Bug Fix to ignore roll and pitch inputs to loiter controller when in radio failsafe 2) Bug Fix to allow compassmot to work on Pixhawk ------------------------------------------------------------------ ArduCopter 3.1.4 8-May-2014 / 3.1.4-rc1 2-May-2014 Changes from 3.1.3 1) Bug Fix for Pixhawk/PX4 NuttX I2C memory corruption when errors are found on I2C bus ------------------------------------------------------------------ ArduCopter 3.1.3 7-Apr-2014 Changes from 3.1.2 1) Stability patch fix which could cause motors to go to min at full throttle and with large roll/pitch inputs ------------------------------------------------------------------ ArduCopter 3.1.2 13-Feb-2014 / ArduCopter 3.1.2-rc2 12-Feb-2014 Changes from 3.1.2-rc1 1) GPS Glitch detection disabled when connected via USB 2) RC_FEEL_RP param added for adjusting responsiveness to pilot roll/pitch input in Stabilize, Drift, AltHold modes ------------------------------------------------------------------ ArduCopter 3.1.2-rc1 30-Jan-2014 Changes from 3.1.1 1) Pixhawk baro bug fix to SPI communication which could cause large altitude estimate jumps at high temperatures ------------------------------------------------------------------ ArduCopter 3.1.1 26-Jan-2014 / ArduCopter 3.1.1-rc2 21-Jan-2014 Changes from 3.1.1-rc1 1) Pixhawk improvements (available for APM2 when AC3.2 is released): a) Faster arming b) AHRS_TRIM fix - reduces movement in loiter when yawing c) AUX Out 5 & 6 turned into general purpose I/O pins d) Three more relays added (relays are pins that can be set to 0V or 5V) e) do-set-servo fix to allow servos to be controlled from ground station f) Motorsync CLI test g) PX4 parameters moved from SD card to eeprom h) additional pre-arm checks for baro & inertial nav altitude and lean angle ------------------------------------------------------------------ ArduCopter 3.1.1-rc1 14-Jan-2014 Changes from 3.1 1) Pixhawk improvements: a) Telemetry port 2 enabled (for MinimOSD) b) SD card reliability improvements c) parameters moved to FRAM d) faster parameter loading via USB e) Futaba SBUS receiver support 2) Bug fixes: a) Loiter initialisation fix (Loiter would act like AltHold until flight mode switch changed position) b) ROI commands were not returning Lat, Lon, Alt to mission planner when mission was loaded from APM 3) TradHeli only fixes: a) Drift now uses same (reduced) collective range as stabilize mode b) AutoTune disabled (for tradheli only) c) Landing collective (smaller than normal collective) used whenever copter is not moving ------------------------------------------------------------------ ArduCopter 3.1 14-Dec-2013 Changes from 3.1-rc8 1) Pixhawk improvements: a) switch to use MPU6k as main accel/gyro b) auto loading of IO-board firmware on startup 2) RTL fixes: a) initialise waypoint leash length (first RTL stop would be more aggressive than 2nd) b) reduce projected stopping distance for higher speed stops ------------------------------------------------------------------ ArduCopter 3.1-rc8 9-Dec-2013 Changes from 3.1-rc7 1) add Y6 motor mapping with all top props CW, bottom pros CCW (set FRAME = 10) 2) Safety Changes: a) ignore yaw input during radio failsafe (previously the copter could return home spinning if yaw was full over at time of failsafe) b) Reduce GPSGLITCH_RADIUS to 2m (was 5m) to catch glitches faster 3) Bug fixes: a) Optical flow SPI bus rates b) TradHeli main rotor ramp up speed fix ------------------------------------------------------------------ ArduCopter 3.1-rc7 22-Nov-2013 Changes from 3.1-rc6 1) MOT_SPIN_ARMED default to 70 2) Smoother inertial nav response to missed GPS messages 3) Safety related changes a) radio and battery failsafe disarm copter if landed in Loiter or AltHold (previously they would RTL) b) Pre-Arm check failure warning output to ground station every 30 seconds until they pass c) INS and inertial nav errors logged to dataflash's PM message d) pre-arm check for ACRO_BAL_ROLL, ACRO_BAL_PITCH ------------------------------------------------------------------ ArduCopter 3.1-rc6 16-Nov-2013 Improvements over 3.1-rc5 1) Heli improvements: a) support for direct drive tails (uses TAIL_TYPE and TAIL_SPEED parameters) b) smooth main rotor ramp-up for those without external govenor (RSC_RAMP_TIME) c) internal estimate of rotor speed configurable with RSC_RUNUP_TIME parameter to ensure rotor at top speed before starting missions d) LAND_COL_MIN collective position used when landed (reduces chance copter will push too hard into the ground when landing or before starting missions) e) reduced collective while in stabilize mode (STAB_COL_MIN, STAB_COL_MAX) for more precise throttle control f) external gyro parameter range changed from 1000~2000 to 0~1000 (more consistent with other parameters) g) dynamic flight detector switches on/off leaky-i term depending on copter speed 2) SingleCopter airframe support (contribution from Bill King) 3) Drift mode replaces TOY 4) MPU6k SPI bus speed decreased to 500khz after 4 errors 5) Safety related changes: a) crash detector cuts motors if copter upside down for more than 2 seconds b) INS (accel and gyro) health check in pre-arm checks c) ARMING_CHECK allows turning on/off individual checks for baro, GPS, compass, parameters, board voltage, radio d) detect Ublox GPS running at less than 5hz and resend configuration e) GPSGlitch acceptable radius reduced to 5m (stricter detection of glitches) f) range check roll, pitch input to ensure crazy radio values don't get through to stabilize controller g) GPS failsafe options to trigger AltHold instead of LAND or to trigger LAND even if in flight mode that does not require GPS h) Battery failsafe option to trigger RTL instead of LAND i) MOT_SPIN_ARMED set to zero by default 6) Bug fixes: a) missing throttle controller initialisation would mean Stabilize mode's throttle could be non-tilt-compensated b) inertial nav baro and gps delay compensation fix (contribution from Neurocopter) c) GPS failsafe was invoking LAND mode which still used GPS for horizontal control ------------------------------------------------------------------ ArduCopter 3.1-rc5 22-Oct-2013 Improvements over 3.1-rc4 1) Pixhawk USB reliability improvements 2) AutoTune changes: a) enabled by default b) status output to GCS c) use 2 pos switch only 3) ch7/ch8 LAND 4) Tricopter stability patch improvements [thanks to texlan] 5) safety improvements: a) slower speed up of motors after arming b) pre-arm check that copter is moving less than 50cm/s if arming in Loiter or fence enabled ------------------------------------------------------------------ ArduCopter 3.1-rc4 13-Oct-2013 Improvements over 3.1-rc3 1) Performance improvements to resolve APM alt hold issues for Octacopters: a) SPI bus speed increased from 500khz to 8Mhz b) Telemetry buffer increased to 512bytes c) broke up medium and slow loops into individual scheduled tasks and increased priority of alt hold tasks 2) Bug fix for Pixhawk USB connection 3) GPS Glitch improvements: a) added GPS glitch check to arming check b) parameters for vehicle max acceleration (GPSGLITCH_ACCEL) and always-ok radius (GPSGLICH_RADIUS) ------------------------------------------------------------------ ArduCopter 3.1-rc3 09-Oct-2013 Improvements over 3.1-rc2 1) GPS Glitch protection - gps positions are compared with the previous gps position. Position accepted if within 10m or copter could have reached the position with max accel of 10m/s/s. 2) Bug fix for pixhawk SPI bus contention that could lead to corrupted accelerometer values on pixhawk resolved 3) Auto Tuning (compile time option only add "#define AUTOTUNE ENABLED" to APM_Config.h and set CH7_Opt or CH8_Opt parameter to 17) 4) CPU Performance improvement when reading from MPU6k for APM 5) SUPER_SIMPLE parameter changed to a bit map to allow some flight modes to use super simpler while others use regular simple (MP release to allow easier selection will go out with AC3.1 official release) 6) Safety changes: a) safety button must be pushed before arming on pixhawk b) RGB LED (aka toshiba led) changed so that disarmed flashes, armed is either blue (if no gps lock) or green (if gps lock) c) sensor health bitmask sent to groundstations ------------------------------------------------------------------ ArduCopter 3.1-rc2 18-Sep-2013 Improvements over 3.1-rc1 1) bug fix for MOT_SPIN_ARMED to allow it to be higher than 127 2) PX4/pixhawk auto-detect internal/external compass so COMPASS_ORIENT should be set to ORIENTATION_NONE if using GPS+compass module ------------------------------------------------------------------ ArduCopter 3.1-rc1 9-Sep-2013 Improvements over 3.0.1 1) Support for Pixhawks board 2) Arm, Disarm, Land and Takeoff in Loiter and AltHold 3) Improved Acro a) ACRO_RP_P, ACRO_YAW_P parameters added to control speed of rotation b) ACRO_BAL_ROLL, ACRO_BAL_PITCH controls speed at which copter returns to level c) ACRO_TRAINER can be set to 0:disable trainer, 1:auto leveling when sticks released, 2:auto leveling and lean angle limited to ANGLE_MAX d) Ch7 & Ch8 switch to set ACRO_TRAINER options in-flight 4) SPORT mode - equivalent of earth frame Acro with support for simple mode 5) Sonar ground tracking improvements and bug fixes that reduce reaction to bad sonar data 6) Safety improvements a) motors always spin when armed (speed can be controlled with MOT_SPIN_ARMED, set to 0 to disable) b) vehicle's maximum lean angle can be reduced (or increased) with the ANGLE_MAX parameter c) arming check that GPS hdop is > 2.0 (disable by setting GPS_HDOP parameter to 900) d) slow take-off in AUTO, LOITER, ALTHOLD to reduce chance of motor/esc burn-out on large copters 7) Bug fixes: a) Optical flow sensor initialisation fix b) altitude control fix for Loiter_turns mission command (i.e. mission version of CIRCLE mode) c) DO_SET_ROI fix (do not use "ROI") 8) Distribute Loiter & Navigation calcs over 4 cycles to reduce impact on a single 100hz loop 9) RCMAP_ parameters allow remapping input channels 1 ~ 4 ------------------------------------------------------------------ ArduCopter 3.0.1-rc2 / 3.0.1 11-Jul-2013 Improvements over 3.0.1-rc1 1) Rate Roll, Pitch and Yaw I fix when we hit motor limits 2) pre-arm check changes: a) double flash arming light when pre-arm checks fail b) relax mag field checks to 35% min, 165% max of expected field 3) loiter and auto changes: a) reduced Loiter speed to 5 m/s b) reduced WP_ACCEL to 1 m/s/s (was 2.5 m/s/s) c) rounding error fix in loiter controller d) bug fix to stopping point calculation for RTL and loiter during missions 4) Stability Patch fix which was freezing Rate Taw I term and allowing uncommanded Yaw ------------------------------------------------------------------ ArduCopter 3.0.1-rc1 26-Jun-2013 Improvements over 3.0.0 1) bug fix to Fence checking position after GPS lock was lost 2) bug fix to LAND so that it does not attempt to maintain horizontal position without GPS lock ------------------------------------------------------------------ ArduCopter 3.0.0 / 3.0.0-rc6 16-Jun-2013 Improvements over 3.0.0-rc5 1) bug fix to Circle mode's start position (was moving to last loiter target) 2) WP_ACCEL parameter added to allow user to adjust acceleration during missions 3) loiter acceleration set to half of LOIT_SPEED parameter value (was hard-coded) 4) reduce AltHold P to 1.0 (was 2.0) ------------------------------------------------------------------ ArduCopter 3.0.0-rc5 04-Jun-2013 Improvements over 3.0.0-rc4 1) bug fix to LAND flight mode in which it could try to fly to mission's next waypoint location 2) bug fix to Circle mode to allow counter-clockwise rotation 3) bug fix to heading change in Loiter, RTL, Missions when pilot's throttle is zero 4) bug fix for mission sticking at take-off command when pilot's throttle is zero 5) bug fix for parameters not saving when new value is same as default value 6) reduce pre-arm board min voltage check to 4.3V (was 4.5V) 7) remove throttle controller's ability to limit lean angle in loiter, rtl, auto ------------------------------------------------------------------ ArduCopter 3.0.0-rc4 02-Jun-2013 Improvements over 3.0.0-rc3 1) loiter improvements: i) repositioning enhanced with feed forward ii) use tan to convert desired accel to lean angle 2) stability patch improvements for high powered copters or those with roll-pitch rate gains set too high 3) auto mode vertical speed fix (it was not reaching the desired speeds) 4) alt hold smoothed by filtering feed forward input 5) circle mode fix to initial position and smoother initialisation 6) RTL returns to initial yaw heading before descending 7) safe features: i) check for gps lock when entering failsafe ii) pre-arm check for mag field length iii) pre-arm check for board voltage between 4.5v ~ 5.8V iv) beep twice during arming v) GPS failsafe enabled by default (will LAND if loses GPS in Loiter, AUTO, Guided modes) vi) bug fix for alt-hold mode spinning motors before pilot has raised throttle 8) bug fixes: i) fixed position mode so it responding to pilot input ii) baro cli test iii) moved cli motor test to test sub menu and minor change to throttle output iv) guided mode yaw control fix ------------------------------------------------------------------ ArduCopter 3.0.0-rc3 22-May-2013 Improvements over 3.0.0-rc2 1) bug fix for dataflash erasing unnecessarily 2) smoother transition to waypoints, loiter: intermediate point's speed initialised from copter's current speed 3) Ch8 auxiliary function switch (same features as Ch7) 4) safety checks: Warning to GCS of reason for pre-arm check failure ARMING_CHECK parameter added to allow disabling pre-arm checks Added compass health and offset check to pre-arm check compassmot procedure displays interference as percentage of total mag field 5) WPNAV dataflash message combined into NTUN message 6) allow TriCopters to use ESC calibration ------------------------------------------------------------------ ArduCopter 3.0.0-rc2 13-May-2013 Improvements over 3.0.0-rc1: 1) smoother transition to waypoints, loiter: reduced loiter max acceleration to smooth waypoints bug fix to uninitialised roll/pitch when entering RTL, AUTO, LOITER 2) fast waypoints - copter does not stop at waypoints unless delay is specified 3) WPNAV_LOIT_SPEED added to allow faster/slower loiter repositioning 4) removed speed limits on auto missions 5) enhance LAND mission command takes lat/lon coordinates 6) bug fix for RTL not pointing home sometimes 7) centrifugal correction disabled when copter is disarmed to stop HUD moving 8) centrifugal correction disabled when sat count less than 6 (AHRS_GPS_MINSATS) 9) compass calibration reliability improvements when run from mission planner 10) bug fix to allow compassmot to be run from mission planner terminal screen 11) add support for H-quad frame 12) add COMPASS_ORIENT parameter to support external compass in any orientation ------------------------------------------------------------------ ArduCopter 3.0.0-rc1 01-May-2013 Improvements over 2.9.1b: 1) Inertial navigation for X & Y axis (Randy/Leonard/Jonathan) 2) 3D waypoint navigation library (Leonard/Randy) WPNAV_SPEED, WPNAV_SPEED_UP, WPNAV_SPEED_DN control target speeds during missions and RTL WP_YAW_BEHAVIOR to allow disabling yaw during missions and RTL 3) PX4 support (some features still not available) (Tridge/Pat/PX4Dev Team) 4) Safety improvements: Tin-can shaped fence (set FENCE_ENABLED to 1 and copter will RTL if alt > 150m or horizontal distance from home > 300m) (Randy/Tridge/Leonard) GCS failsafe (set FS_GCS_ENABLED to 1 and if you are using a tablet to fly your copter it will RTL and return control to the radio 3 seconds after losing telemetry) (Randy) pre-arm checks to ensure accelerometer and radio calibration has been performed before arming (Randy) 5) motor interference compensation for compass (Jonathan/Randy) 6) Circle mode improvements: set CIRCLE_RADIUS to zero to do panorama shots in circle mode (copter does not move in a circle but instead slowly rotates) CIRCLE_RATE parameter allows controlling direction and speed of rotation in CIRCLE mode and LOITER_TURNS (can also be adjusted in flight from CH6 knob) 7) SONAR_GAIN parameter add to allow reducing the response to objects sensed by sonar (Randy) 8) support for trapezoidal quads (aka V shaped or FPV quads) (Leonard/Craig) 9) performance improvements to dataflash logging (Tridge) 10) bug-fix to analog read which could cause bad sonar reads when using voltage or current monitor (Tridge) 11) bug-fix to motors going to minimum when throttle is low while switching into Loiter, AUTO, RTL, ALT_HOLD (Jason/Randy) 12) bug-fix for auto disarm sometimes disarming shortly after arming (Jason/SirAlex) ------------------------------------------------------------------ ArduCopter 2.9.1b 30-Feb-2013 Improvements over 2.9.1: 1) reduce INS_MPU6K_FILTER to 20hz 2) reduce InertialNav Z-axis time constant to 5 (was 7) 3) increased max InertialNav accel correction to 3 m/s (was 1m/s) 4) bug fix for alt_hold being passed as int16_t to get_throttle_althold_with_slew 5) bug fix for throttle after acro flip (was being kept at min throttle if pilot switched out of ACRO mode while inverted) 6) reduce yaw_rate P default to 0.20 (was 0.25) ------------------------------------------------------------------ ArduCopter 2.9.1 & 2.9.1-rc2 01-Feb-2013 Improvements over 2.9.1-rc1: 1) small corretion to use of THR_MID to scale lower end of manual throttle between THR_MIN and 500 instead of 0 and 500 2) bug fix for longitude scaling being incorrectly calculated using Next Waypoint instead of home which could lead to scaling being 1 3) ESC calibration change to set update rate to ESCs to 50hz to allow simonk ESC to be calibrated ------------------------------------------------------------------ ArduCopter 2.9.1-rc1 31-Jan-2013 Improvements over 2.9: 1) THR_MID parameter added to allow users to adjust the manual throttle so that vehicle hovers at about mid stick 2) bug fix for autotrim - roll axis was backwards 3) bug fix to set sonar_alt_health to zero when sonar is disabled 4) capture level roll and pitch trims as part of accel calibration 5) bug fix to ppm encoder false positives ------------------------------------------------------------------ ArduCopter 2.9 & 2.9-rc5 14-Jan-2013 Improvements over 2.9-rc4: 1) add constraint to loiter commanded roll and pitch angles 2) relax altitude requirement for take-off command to complete ------------------------------------------------------------------ ArduCopter 2.9-rc4 12-Jan-2013 Improvements over 2.9-rc3: 1) Smoother transition between manual and auto flight modes (Leonard) 2) bug fix for LAND not actually landing when initiated from failsafe (Randy/Craig) ------------------------------------------------------------------ ArduCopter 2.9-rc3 11-Jan-2013 Improvements over 2.9-rc2: 1) alt hold with sonar improvements - now on by default (Leonard/Randy) 2) performance and memory usage improvements (Tridge/Randy) 3) increase APM1 baro pressure read from 5hz to 8.3hz to improve alt hold (Randy) 4) bug fix: altitude error reported to GCS (Randy) 5) limit inertial nav's max accel offset correction to 100cm/s/s to speed up recovery after hard impacts (Randy)_ 6) moved rate controllers to run after ins read (Tridge/Randy) ------------------------------------------------------------------ ArduCopter 2.9-rc2 31-Dec-2012 Improvements over 2.9-rc1: 1) increased throttle rate gains from 1.0 to 6.0 2) APM1 fix so it works with inertial nav (5hz update rate of baro was beyond the tolerance set in the inav library) ------------------------------------------------------------------ ArduCopter 2.9-rc1 23-Dec-2012 Improvements over 2.8.1: 1) altitude hold improvements: a)inertial navigation for vertical axis [Randy/Jonathan/Leonard/Jason] b)accel based throttle controller [Leonard/Randy] c)accelerometer calibration routine updated to use gauss-newton method [Randy/Tridge/Rolfe Schmidt] d)parameters to control climb rate: AUTO_VELZ_MIN, AUTO_VELZ_MAX - allows you to control the maximum climb and descent rates of the autopilot (in cm/s) PILOT_VELZ_MAX - allows you to control the maximum climb/descent rate when in alt hold or loiter (in cm/s) 2) landing improvements [Leonard/Randy] LAND_SPEED - allows you to set the landing speed in cm/s 3) camera related improvements: a) AP_Relay enabled for APM2 and integrated with AP_Camera [Sandro Benigno] b) camera trigger with channel 7 switch or DO_DIGICAM_CONTROL mission command [Randy] c) allow yaw override by pilot or with CONDITIONAL_YAW command during missions [Randy] YAW_OVR_BEHAVE - Controls when autopilot takes back normal control of yaw after pilot overrides (0=after next wp, 1=never) 4) trad heli improvements [Rob] a) code tested and brought back into the fold (2.8.1 was never released for trad helis) b) enabled rate controller (previously only used angle controllers) c) fix to rotor speed controllers - now operates by switching off channel 8 d) allow wider collective pitch range in acro and alt hold modes vs stabilize mode e) removed angle boost function because it created more problems than it solved f) bug fix to allow collective pitch to use the entire range of servos 5) mediatek gps driver improvements [Craig] a) added support for 1.9 firmware b) bug fix to start-up routine so sbas can be enabled 6) failsafe improvements (both throttle and battery) [Randy/Craig/John Arne Birkeland] a) RTL will not trigger if your throttle is zero - reduces risk of accidentally invoking RTL if you switch off your receiver before disarming b) failsafe triggered in unlikely case of a PPM encoder failure c) bug fix to resolve motors momentarily reducing to zero after failsafe is triggered 7) mpu6k filtering made configurable and default changed to 42hz for copters [Leonard/Tridge] 8) support ppm sum for transmitters with as few as 5 channels [Randy/John Arne Birkeland] 9) acro trainer - copter will return to be generally upright if you release the sticks in acro mode [Leonard] ACRO_BAL_ROLL, ACRO_BAL_PITCH - controls rate at which roll returns to level ACRO_TRAINER - 1 to enable the auto-bring-upright feature 10) other changes and bug fixes: a) allow >45 degrees when in stabilize mode by adding lines like below to APM_Config (compile time option only) [Jason] #define MAX_INPUT_ROLL_ANGLE 6000 // 60 degrees #define MAX_INPUT_PITCH_ANGLE 6000 // 60 degrees b) bug fix to stop RTL from ever climbing to an unreasonable height (i.e. >80m) [Jason] c) event and state logging [Jason] d) allow cli to be used over telemetry link [Tridge] e) bug fix to allow compass accumulate to run when we have spare cpu cycles [Randy] f) bug fix so do_set_servo command works [Randy] g) bug fix to PID controller's so they don't calculate crazy D term on the first call [Tridge] h) bug fix to initialise navigation parameter to resolve twitch when entering some navigation modes [Jason] i) performance improvement to copter leds - use DigitalFastWrite and DigitalFastRead instead of native arduino functions [Randy] j) removed unused stab_d from roll and pitch controller [Jason] k) bug fix for guided mode not reaching target altitude if it reaches horizontal target first [Randy] l) code clean-up, parameter documentation improvements [Randy/Jason/Rob/others] ------------------------------------------------------------------ ArduCopter 2.8.1 22-Oct-2012 Improvements over 2.8: - 430 bytes of RAM freed up to resolve APM1 level issue and reduce chance of memory corruption on both APM1 and APM2 Improvements over 2.7.3: - Improved ACRO mode (Leonard Hall) - Improved stability patch to reduce "climb-on-yaw" problem (Leonard, Rob Lefebvre, Randy) - Rate controller targets moved to body frames (yaw control now works properly when copter is inverted) (Leonard/Randy) - Less bouncy Stabilize yaw control (Leonard) - OpticalFlow sensor support for APM2.5 (Randy) - DMP works again by adding "#define DMP_ENABLED ENABLED" to APM_Config.h You can also log DMP vs DCM to the dataflash by adding "#define SECONDARY_DMP_ENABLED ENABLED" (Randy) - Watch dog added to shutdown motors if main loop feezes for 2 seconds (Randy) - Thrust curve added to linearize pwm->thrust. Removes deadzone found above 90% throttle in most ESC/motors (Randy) - More timing improvements (main loop is now tied to MPU6000s interrupt) (Randy) - GPS NMEA bug fix (Alexey Kozin) - Logging improvements (log I terms, dump all settings at head of dataflash log) (Jason) Bug Fixes / Parameter changes: - fixed skipping of last waypoint (Jason) - resolved twitching when no GPS attached (Tridge) - fixed loss of altitude if alt hold is engaged before first GPS lock (Randy/Jason) - moved Roll-Pitch I terms from Stabilize controllers to Rate controllers - TILT_COMPENSATION param tuned for TradHeli (Rob) Code Cleanup: - HAL changes for platform portability (Pat Hickey) - Removed INSTANT_PWM (Randy) ------------------------------------------------------------------