// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*- #include "AP_TECS.h" #include extern const AP_HAL::HAL& hal; #if CONFIG_HAL_BOARD == HAL_BOARD_AVR_SITL #include # define Debug(fmt, args ...) do {printf("%s:%d: " fmt "\n", __FUNCTION__, __LINE__, ## args); hal.scheduler->delay(1); } while(0) #else # define Debug(fmt, args ...) #endif //Debug("%.2f %.2f %.2f %.2f \n", var1, var2, var3, var4); // table of user settable parameters const AP_Param::GroupInfo AP_TECS::var_info[] PROGMEM = { // @Param: CLMB_MAX // @DisplayName: Maximum Climb Rate (metres/sec) // @Description: This is the best climb rate that the aircraft can achieve with the throttle set to THR_MAX and the airspeed set to the default value. For electric aircraft make sure this number can be achieved towards the end of flight when the battery voltage has reduced. The setting of this parameter can be checked by commanding a positive altitude change of 100m in loiter, RTL or guided mode. If the throttle required to climb is close to THR_MAX and the aircraft is maintaining airspeed, then this parameter is set correctly. If the airspeed starts to reduce, then the parameter is set to high, and if the throttle demand require to climb and maintain speed is noticeably less than THR_MAX, then either CLMB_MAX should be increased or THR_MAX reduced. // @Increment: 0.1 // @User: User AP_GROUPINFO("CLMB_MAX", 0, AP_TECS, _maxClimbRate, 5.0f), // @Param: SINK_MIN // @DisplayName: Minimum Sink Rate (metres/sec) // @Description: This is the sink rate of the aircraft with the throttle set to THR_MIN and the same airspeed as used to measure CLMB_MAX. // @Increment: 0.1 // @User: User AP_GROUPINFO("SINK_MIN", 1, AP_TECS, _minSinkRate, 2.0f), // @Param: TIME_CONST // @DisplayName: Controller time constant (sec) // @Description: This is the time constant of the TECS control algorithm. Smaller values make it faster to respond, large values make it slower to respond. // @Range: 3.0-10.0 // @Increment: 0.2 // @User: Advanced AP_GROUPINFO("TIME_CONST", 2, AP_TECS, _timeConst, 5.0f), // @Param: THR_DAMP // @DisplayName: Controller throttle damping // @Description: This is the damping gain for the throttle demand loop. Increase to add damping to correct for oscillations in speed and height. // @Range: 0.1-1.0 // @Increment: 0.1 // @User: Advanced AP_GROUPINFO("THR_DAMP", 3, AP_TECS, _thrDamp, 0.5f), // @Param: INTEG_GAIN // @DisplayName: Controller integrator // @Description: This is the integrator gain on the control loop. Increase to increase the rate at which speed and height offsets are trimmed out // @Range: 0.0-0.5 // @Increment: 0.02 // @User: Advanced AP_GROUPINFO("INTEG_GAIN", 4, AP_TECS, _integGain, 0.1f), // @Param: VERT_ACC // @DisplayName: Vertical Acceleration Limit (metres/sec^2) // @Description: This is the maximum vertical acceleration either up or down that the controller will use to correct speed or height errors. // @Range: 1.0-10.0 // @Increment: 0.5 // @User: Advanced AP_GROUPINFO("VERT_ACC", 5, AP_TECS, _vertAccLim, 7.0f), // @Param: HGT_OMEGA // @DisplayName: Height complementary filter frequency (radians/sec) // @Description: This is the cross-over frequency of the complementary filter used to fuse vertical acceleration and baro alt to obtain an estimate of height rate and height. // @Range: 1.0-5.0 // @Increment: 0.05 // @User: Advanced AP_GROUPINFO("HGT_OMEGA", 6, AP_TECS, _hgtCompFiltOmega, 3.0f), // @Param: SPD_OMEGA // @DisplayName: Speed complementary filter frequency (radians/sec) // @Description: This is the cross-over frequency of the complementary filter used to fuse longitudinal acceleration and airspeed to obtain a lower noise and lag estimate of airspeed. // @Range: 0.5-2.0 // @Increment: 0.05 // @User: Advanced AP_GROUPINFO("SPD_OMEGA", 7, AP_TECS, _spdCompFiltOmega, 2.0f), // @Param: RLL2THR // @DisplayName: Bank angle compensation gain // @Description: Increasing this gain turn increases the amount of throttle that will be used to compensate for the additional drag created by turning. Ideally this should be set to approximately 10 x the extra sink rate in m/s created by a 45 degree bank turn. Increase this gain if the aircraft initially loses energy in turns and reduce if the aircraft initially gains energy in turns. Efficient high aspect-ratio aircraft (eg powered sailplanes) can use a lower value, whereas inefficient low aspect-ratio models (eg delta wings) can use a higher value. // @Range: 5.0 to 30.0 // @Increment: 1.0 // @User: Advanced AP_GROUPINFO("RLL2THR", 8, AP_TECS, _rollComp, 10.0f), // @Param: SPDWEIGHT // @DisplayName: Weighting applied to speed control // @Description: This parameter adjusts the amount of weighting that the pitch control applies to speed vs height errors. Setting it to 0.0 will cause the pitch control to control height and ignore speed errors. This will normally improve height accuracy but give larger airspeed errors. Setting it to 2.0 will cause the pitch control loop to control speed and ignore height errors. This will normally reduce airsped errors, but give larger height errors. A value of 1.0 gives a balanced response and is the default. // @Range: 0.0 to 2.0 // @Increment: 0.1 // @User: Advanced AP_GROUPINFO("SPDWEIGHT", 9, AP_TECS, _spdWeight, 1.0f), // @Param: PTCH_DAMP // @DisplayName: Controller pitch damping // @Description: This is the damping gain for the pitch demand loop. Increase to add damping to correct for oscillations in speed and height. // @Range: 0.1-1.0 // @Increment: 0.1 // @User: Advanced AP_GROUPINFO("PTCH_DAMP", 10, AP_TECS, _ptchDamp, 0.0f), // @Param: SINK_MAX // @DisplayName: Maximum Descent Rate (metres/sec) // @Description: This sets the maximum descent rate that the controller will use. If this value is too large, the aircraft will reach the pitch angle limit first and be enable to achieve the descent rate. This should be set to a value that can be achieved at the lower pitch angle limit. // @Increment: 0.1 // @User: User AP_GROUPINFO("SINK_MAX", 11, AP_TECS, _maxSinkRate, 5.0f), // @Param: LAND_ARSPD // @DisplayName: Airspeed during landing approach (m/s) // @Description: When performing an autonomus landing, this value is used as the goal airspeed during approach. Note that this parameter is not useful if your platform does not have an airspeed sensor (use TECS_LAND_THR instead). If negative then this value is not used during landing. // @Range: -1 to 127 // @Increment: 1 // @User: User AP_GROUPINFO("LAND_ARSPD", 12, AP_TECS, _landAirspeed, -1), // @Param: LAND_THR // @DisplayName: Cruise throttle during landing approach (percentage) // @Description: Use this parameter instead of LAND_ASPD if your platform does not have an airspeed sensor. It is the cruise throttle during landing approach. If it is negative if TECS_LAND_ASPD is in use then this value is not used during landing. // @Range: -1 to 100 // @Increment: 0.1 // @User: User AP_GROUPINFO("LAND_THR", 13, AP_TECS, _landThrottle, -1), // @Param: LAND_SPDWGT // @DisplayName: Weighting applied to speed control during landing. // @Description: Same as SPDWEIGHT parameter, with the exception that this parameter is applied during landing flight stages. A value closer to 2 will result in the plane ignoring height error during landing and our experience has been that the plane will therefore keep the nose up -- sometimes good for a glider landing (with the side effect that you will likely glide a ways past the landing point). A value closer to 0 results in the plane ignoring speed error -- use caution when lowering the value below 1 -- ignoring speed could result in a stall. // @Range: 0.0 to 2.0 // @Increment: 0.1 // @User: Advanced AP_GROUPINFO("LAND_SPDWGT", 14, AP_TECS, _spdWeightLand, 1.0f), // @Param: PITCH_MAX // @DisplayName: Maximum pitch in auto flight // @Description: This controls maximum pitch up in automatic throttle modes. If this is set to zero then LIM_PITCH_MAX is used instead. The purpose of this parameter is to allow the use of a smaller pitch range when in automatic flight than what is used in FBWA mode. // @Range: 0 45 // @Increment: 1 // @User: Advanced AP_GROUPINFO("PITCH_MAX", 15, AP_TECS, _pitch_max, 0), // @Param: PITCH_MIN // @DisplayName: Minimum pitch in auto flight // @Description: This controls minimum pitch in automatic throttle modes. If this is set to zero then LIM_PITCH_MIN is used instead. The purpose of this parameter is to allow the use of a smaller pitch range when in automatic flight than what is used in FBWA mode. Note that TECS_PITCH_MIN should be a negative number. // @Range: -45 0 // @Increment: 1 // @User: Advanced AP_GROUPINFO("PITCH_MIN", 16, AP_TECS, _pitch_min, 0), // @Param: LAND_SINK // @DisplayName: Sink rate for final landing stage // @Description: The sink rate in meters/second for the final stage of landing. // @Range: 0.0 to 2.0 // @Increment: 0.1 // @User: Advanced AP_GROUPINFO("LAND_SINK", 17, AP_TECS, _land_sink, 0.25f), // @Param: TECS_LAND_TCONST // @DisplayName: Land controller time constant (sec) // @Description: This is the time constant of the TECS control algorithm when in final landing stage of flight. It should be smaller than TECS_TIME_CONST to allow for faster flare // @Range: 1.0-5.0 // @Increment: 0.2 // @User: Advanced AP_GROUPINFO("LAND_TCONST", 18, AP_TECS, _landTimeConst, 2.0f), AP_GROUPEND }; /* * Written by Paul Riseborough 2013 to provide: * - Combined control of speed and height using throttle to control * total energy and pitch angle to control exchange of energy between * potential and kinetic. * Selectable speed or height priority modes when calculating pitch angle * - Fallback mode when no airspeed measurement is available that * sets throttle based on height rate demand and switches pitch angle control to * height priority * - Underspeed protection that demands maximum throttle and switches pitch angle control * to speed priority mode * - Relative ease of tuning through use of intuitive time constant, integrator and damping gains and the use * of easy to measure aircraft performance data * */ void AP_TECS::update_50hz(float hgt_afe) { // Implement third order complementary filter for height and height rate // estimted height rate = _climb_rate // estimated height above field elevation = _integ3_state // Reference Paper : // Optimising the Gains of the Baro-Inertial Vertical Channel // Widnall W.S, Sinha P.K, // AIAA Journal of Guidance and Control, 78-1307R // Calculate time in seconds since last update uint32_t now = hal.scheduler->micros(); float DT = max((now - _update_50hz_last_usec),0)*1.0e-6f; if (DT > 1.0f) { _integ3_state = hgt_afe; _climb_rate = 0.0f; _integ1_state = 0.0f; DT = 0.02f; // when first starting TECS, use a // small time constant } _update_50hz_last_usec = now; // USe inertial nav verical velocity and height if available Vector3f posned, velned; if (_ahrs.get_velocity_NED(velned) && _ahrs.get_relative_position_NED(posned)) { _climb_rate = - velned.z; _integ3_state = - posned.z; } else { // Get height acceleration float hgt_ddot_mea = -(_ahrs.get_accel_ef().z + GRAVITY_MSS); // Perform filter calculation using backwards Euler integration // Coefficients selected to place all three filter poles at omega float omega2 = _hgtCompFiltOmega*_hgtCompFiltOmega; float hgt_err = hgt_afe - _integ3_state; float integ1_input = hgt_err * omega2 * _hgtCompFiltOmega; _integ1_state = _integ1_state + integ1_input * DT; float integ2_input = _integ1_state + hgt_ddot_mea + hgt_err * omega2 * 3.0f; _climb_rate = _climb_rate + integ2_input * DT; float integ3_input = _climb_rate + hgt_err * _hgtCompFiltOmega * 3.0f; // If more than 1 second has elapsed since last update then reset the integrator state // to the measured height if (DT > 1.0f) { _integ3_state = hgt_afe; } else { _integ3_state = _integ3_state + integ3_input*DT; } } // Update and average speed rate of change // Get DCM const Matrix3f &rotMat = _ahrs.get_dcm_matrix(); // Calculate speed rate of change float temp = rotMat.c.x * GRAVITY_MSS + _ahrs.get_ins().get_accel().x; // take 5 point moving average _vel_dot = _vdot_filter.apply(temp); } void AP_TECS::_update_speed(void) { // Calculate time in seconds since last update uint32_t now = hal.scheduler->micros(); float DT = max((now - _update_speed_last_usec),0)*1.0e-6f; _update_speed_last_usec = now; // Convert equivalent airspeeds to true airspeeds float EAS2TAS = _ahrs.get_EAS2TAS(); _TAS_dem = _EAS_dem * EAS2TAS; _TASmax = aparm.airspeed_max * EAS2TAS; _TASmin = aparm.airspeed_min * EAS2TAS; if (_landAirspeed >= 0 && _ahrs.airspeed_sensor_enabled() && (_flight_stage == FLIGHT_LAND_APPROACH || _flight_stage== FLIGHT_LAND_FINAL)) { _TAS_dem = _landAirspeed * EAS2TAS; if (_TASmin > _TAS_dem) { _TASmin = _TAS_dem; } } // Reset states of time since last update is too large if (DT > 1.0f) { _integ5_state = (_EAS * EAS2TAS); _integ4_state = 0.0f; DT = 0.1f; // when first starting TECS, use a // small time constant } // Get airspeed or default to halfway between min and max if // airspeed is not being used and set speed rate to zero if (!_ahrs.airspeed_sensor_enabled() || !_ahrs.airspeed_estimate(&_EAS)) { // If no airspeed available use average of min and max _EAS = 0.5f * (aparm.airspeed_min.get() + (float)aparm.airspeed_max.get()); } // Implement a second order complementary filter to obtain a // smoothed airspeed estimate // airspeed estimate is held in _integ5_state float aspdErr = (_EAS * EAS2TAS) - _integ5_state; float integ4_input = aspdErr * _spdCompFiltOmega * _spdCompFiltOmega; // Prevent state from winding up if (_integ5_state < 3.1f){ integ4_input = max(integ4_input , 0.0f); } _integ4_state = _integ4_state + integ4_input * DT; float integ5_input = _integ4_state + _vel_dot + aspdErr * _spdCompFiltOmega * 1.4142f; _integ5_state = _integ5_state + integ5_input * DT; // limit the airspeed to a minimum of 3 m/s _integ5_state = max(_integ5_state, 3.0f); } void AP_TECS::_update_speed_demand(void) { // Set the airspeed demand to the minimum value if an underspeed condition exists // or a bad descent condition exists // This will minimise the rate of descent resulting from an engine failure, // enable the maximum climb rate to be achieved and prevent continued full power descent // into the ground due to an unachievable airspeed value if ((_badDescent) || (_underspeed)) { _TAS_dem = _TASmin; } // Constrain speed demand _TAS_dem = constrain_float(_TAS_dem, _TASmin, _TASmax); // calculate velocity rate limits based on physical performance limits // provision to use a different rate limit if bad descent or underspeed condition exists // Use 50% of maximum energy rate to allow margin for total energy contgroller float velRateMax; float velRateMin; if ((_badDescent) || (_underspeed)) { velRateMax = 0.5f * _STEdot_max / _integ5_state; velRateMin = 0.5f * _STEdot_min / _integ5_state; } else { velRateMax = 0.5f * _STEdot_max / _integ5_state; velRateMin = 0.5f * _STEdot_min / _integ5_state; } // Apply rate limit if ((_TAS_dem - _TAS_dem_adj) > (velRateMax * 0.1f)) { _TAS_dem_adj = _TAS_dem_adj + velRateMax * 0.1f; _TAS_rate_dem = velRateMax; } else if ((_TAS_dem - _TAS_dem_adj) < (velRateMin * 0.1f)) { _TAS_dem_adj = _TAS_dem_adj + velRateMin * 0.1f; _TAS_rate_dem = velRateMin; } else { _TAS_dem_adj = _TAS_dem; _TAS_rate_dem = (_TAS_dem - _TAS_dem_last) / 0.1f; } // Constrain speed demand again to protect against bad values on initialisation. _TAS_dem_adj = constrain_float(_TAS_dem_adj, _TASmin, _TASmax); _TAS_dem_last = _TAS_dem; } void AP_TECS::_update_height_demand(void) { // Apply 2 point moving average to demanded height // This is required because height demand is only updated at 5Hz _hgt_dem = 0.5f * (_hgt_dem + _hgt_dem_in_old); _hgt_dem_in_old = _hgt_dem; // Limit height rate of change if ((_hgt_dem - _hgt_dem_prev) > (_maxClimbRate * 0.1f)) { _hgt_dem = _hgt_dem_prev + _maxClimbRate * 0.1f; } else if ((_hgt_dem - _hgt_dem_prev) < (-_maxSinkRate * 0.1f)) { _hgt_dem = _hgt_dem_prev - _maxSinkRate * 0.1f; } _hgt_dem_prev = _hgt_dem; // Apply first order lag to height demand _hgt_dem_adj = 0.05f * _hgt_dem + 0.95f * _hgt_dem_adj_last; _hgt_dem_adj_last = _hgt_dem_adj; // in final landing stage force height rate demand to the // configured sink rate if (_flight_stage == FLIGHT_LAND_FINAL) { if (_flare_counter == 0) { _hgt_rate_dem = _climb_rate; } // bring it in over 1s to prevent overshoot if (_flare_counter < 10) { _hgt_rate_dem = _hgt_rate_dem * 0.8f - 0.2f * _land_sink; _flare_counter++; } else { _hgt_rate_dem = - _land_sink; } } else { _hgt_rate_dem = (_hgt_dem_adj - _hgt_dem_adj_last) / 0.1f; _flare_counter = 0; } } void AP_TECS::_detect_underspeed(void) { if (((_integ5_state < _TASmin * 0.9f) && (_throttle_dem >= _THRmaxf * 0.95f) && _flight_stage != AP_TECS::FLIGHT_LAND_FINAL) || ((_integ3_state < _hgt_dem_adj) && _underspeed)) { _underspeed = true; } else { _underspeed = false; } } void AP_TECS::_update_energies(void) { // Calculate specific energy demands _SPE_dem = _hgt_dem_adj * GRAVITY_MSS; _SKE_dem = 0.5f * _TAS_dem_adj * _TAS_dem_adj; // Calculate specific energy rate demands _SPEdot_dem = _hgt_rate_dem * GRAVITY_MSS; _SKEdot_dem = _integ5_state * _TAS_rate_dem; // Calculate specific energy _SPE_est = _integ3_state * GRAVITY_MSS; _SKE_est = 0.5f * _integ5_state * _integ5_state; // Calculate specific energy rate _SPEdot = _climb_rate * GRAVITY_MSS; _SKEdot = _integ5_state * _vel_dot; } /* current time constant. It is lower in landing to try to give a precise approach */ float AP_TECS::timeConstant(void) { if (_flight_stage==FLIGHT_LAND_FINAL || _flight_stage==FLIGHT_LAND_APPROACH) { return _landTimeConst; } return _timeConst; } void AP_TECS::_update_throttle(void) { // Calculate limits to be applied to potential energy error to prevent over or underspeed occurring due to large height errors float SPE_err_max = 0.5f * _TASmax * _TASmax - _SKE_dem; float SPE_err_min = 0.5f * _TASmin * _TASmin - _SKE_dem; // Calculate total energy error _STE_error = constrain_float((_SPE_dem - _SPE_est), SPE_err_min, SPE_err_max) + _SKE_dem - _SKE_est; float STEdot_dem = constrain_float((_SPEdot_dem + _SKEdot_dem), _STEdot_min, _STEdot_max); float STEdot_error = STEdot_dem - _SPEdot - _SKEdot; // Apply 0.5 second first order filter to STEdot_error // This is required to remove accelerometer noise from the measurement STEdot_error = 0.2f*STEdot_error + 0.8f*_STEdotErrLast; _STEdotErrLast = STEdot_error; // Calculate throttle demand // If underspeed condition is set, then demand full throttle if (_underspeed) { _throttle_dem = 1.0f; } else { // Calculate gain scaler from specific energy error to throttle float K_STE2Thr = 1 / (timeConstant() * (_STEdot_max - _STEdot_min)); // Calculate feed-forward throttle float ff_throttle = 0; float nomThr = aparm.throttle_cruise * 0.01f; const Matrix3f &rotMat = _ahrs.get_dcm_matrix(); // Use the demanded rate of change of total energy as the feed-forward demand, but add // additional component which scales with (1/cos(bank angle) - 1) to compensate for induced // drag increase during turns. float cosPhi = sqrtf((rotMat.a.y*rotMat.a.y) + (rotMat.b.y*rotMat.b.y)); STEdot_dem = STEdot_dem + _rollComp * (1.0f/constrain_float(cosPhi * cosPhi , 0.1f, 1.0f) - 1.0f); ff_throttle = nomThr + STEdot_dem / (_STEdot_max - _STEdot_min) * (_THRmaxf - _THRminf); // Calculate PD + FF throttle _throttle_dem = (_STE_error + STEdot_error * _thrDamp) * K_STE2Thr + ff_throttle; // Constrain throttle demand _throttle_dem = constrain_float(_throttle_dem, _THRminf, _THRmaxf); // Rate limit PD + FF throttle // Calculate the throttle increment from the specified slew time if (aparm.throttle_slewrate != 0) { float thrRateIncr = _DT * (_THRmaxf - _THRminf) * aparm.throttle_slewrate * 0.01f; _throttle_dem = constrain_float(_throttle_dem, _last_throttle_dem - thrRateIncr, _last_throttle_dem + thrRateIncr); _last_throttle_dem = _throttle_dem; } // Calculate integrator state upper and lower limits // Set to a value that will allow 0.1 (10%) throttle saturation to allow for noise on the demand // Additionally constrain the integrator state amplitude so that the integrator comes off limits faster. float maxAmp = 0.5f*(_THRmaxf - _THRminf); float integ_max = constrain_float((_THRmaxf - _throttle_dem + 0.1f),-maxAmp,maxAmp); float integ_min = constrain_float((_THRminf - _throttle_dem - 0.1f),-maxAmp,maxAmp); // Calculate integrator state, constraining state // Set integrator to a max throttle value during climbout _integ6_state = _integ6_state + (_STE_error * _integGain) * _DT * K_STE2Thr; if (_flight_stage == AP_TECS::FLIGHT_TAKEOFF) { _integ6_state = integ_max; } else { _integ6_state = constrain_float(_integ6_state, integ_min, integ_max); } // Sum the components. // Only use feed-forward component if airspeed is not being used if (_ahrs.airspeed_sensor_enabled()) { _throttle_dem = _throttle_dem + _integ6_state; } else { _throttle_dem = ff_throttle; } } // Constrain throttle demand _throttle_dem = constrain_float(_throttle_dem, _THRminf, _THRmaxf); } void AP_TECS::_update_throttle_option(int16_t throttle_nudge) { // Calculate throttle demand by interpolating between pitch and throttle limits float nomThr; //If landing and we don't have an airspeed sensor and we have a non-zero //TECS_LAND_THR param then use it if ((_flight_stage == FLIGHT_LAND_APPROACH || _flight_stage== FLIGHT_LAND_FINAL) && _landThrottle >= 0) { nomThr = (_landThrottle + throttle_nudge) * 0.01f; } else { //not landing or not using TECS_LAND_THR parameter nomThr = (aparm.throttle_cruise + throttle_nudge)* 0.01f; } if (_flight_stage == AP_TECS::FLIGHT_TAKEOFF) { _throttle_dem = _THRmaxf; } else if (_pitch_dem > 0.0f && _PITCHmaxf > 0.0f) { _throttle_dem = nomThr + (_THRmaxf - nomThr) * _pitch_dem / _PITCHmaxf; } else if (_pitch_dem < 0.0f && _PITCHminf < 0.0f) { _throttle_dem = nomThr + (_THRminf - nomThr) * _pitch_dem / _PITCHminf; } else { _throttle_dem = nomThr; } // Calculate additional throttle for turn drag compensation including throttle nudging const Matrix3f &rotMat = _ahrs.get_dcm_matrix(); // Use the demanded rate of change of total energy as the feed-forward demand, but add // additional component which scales with (1/cos(bank angle) - 1) to compensate for induced // drag increase during turns. float cosPhi = sqrtf((rotMat.a.y*rotMat.a.y) + (rotMat.b.y*rotMat.b.y)); float STEdot_dem = _rollComp * (1.0f/constrain_float(cosPhi * cosPhi , 0.1f, 1.0f) - 1.0f); _throttle_dem = _throttle_dem + STEdot_dem / (_STEdot_max - _STEdot_min) * (_THRmaxf - _THRminf); } void AP_TECS::_detect_bad_descent(void) { // Detect a demanded airspeed too high for the aircraft to achieve. This will be // evident by the the following conditions: // 1) Underspeed protection not active // 2) Specific total energy error > 200 (greater than ~20m height error) // 3) Specific total energy reducing // 4) throttle demand > 90% // If these four conditions exist simultaneously, then the protection // mode will be activated. // Once active, the following condition are required to stay in the mode // 1) Underspeed protection not active // 2) Specific total energy error > 0 // This mode will produce an undulating speed and height response as it cuts in and out but will prevent the aircraft from descending into the ground if an unachievable speed demand is set float STEdot = _SPEdot + _SKEdot; if ((!_underspeed && (_STE_error > 200.0f) && (STEdot < 0.0f) && (_throttle_dem >= _THRmaxf * 0.9f)) || (_badDescent && !_underspeed && (_STE_error > 0.0f))) { _badDescent = true; } else { _badDescent = false; } } void AP_TECS::_update_pitch(void) { // Calculate Speed/Height Control Weighting // This is used to determine how the pitch control prioritises speed and height control // A weighting of 1 provides equal priority (this is the normal mode of operation) // A SKE_weighting of 0 provides 100% priority to height control. This is used when no airspeed measurement is available // A SKE_weighting of 2 provides 100% priority to speed control. This is used when an underspeed condition is detected. In this instance, if airspeed // rises above the demanded value, the pitch angle will be increased by the TECS controller. float SKE_weighting = constrain_float(_spdWeight, 0.0f, 2.0f); if (!_ahrs.airspeed_sensor_enabled()) { SKE_weighting = 0.0f; } else if ( _underspeed || _flight_stage == AP_TECS::FLIGHT_TAKEOFF) { SKE_weighting = 2.0f; } else if (_flight_stage == AP_TECS::FLIGHT_LAND_APPROACH || _flight_stage == AP_TECS::FLIGHT_LAND_FINAL) { SKE_weighting = constrain_float(_spdWeightLand, 0.0f, 2.0f); } float SPE_weighting = 2.0f - SKE_weighting; // Calculate Specific Energy Balance demand, and error float SEB_dem = _SPE_dem * SPE_weighting - _SKE_dem * SKE_weighting; float SEBdot_dem = _SPEdot_dem * SPE_weighting - _SKEdot_dem * SKE_weighting; float SEB_error = SEB_dem - (_SPE_est * SPE_weighting - _SKE_est * SKE_weighting); float SEBdot_error = SEBdot_dem - (_SPEdot * SPE_weighting - _SKEdot * SKE_weighting); // Calculate integrator state, constraining input if pitch limits are exceeded float integ7_input = SEB_error * _integGain; if (_pitch_dem_unc > _PITCHmaxf) { integ7_input = min(integ7_input, _PITCHmaxf - _pitch_dem_unc); } else if (_pitch_dem_unc < _PITCHminf) { integ7_input = max(integ7_input, _PITCHminf - _pitch_dem_unc); } _integ7_state = _integ7_state + integ7_input * _DT; // Apply max and min values for integrator state that will allow for no more than // 5deg of saturation. This allows for some pitch variation due to gusts before the // integrator is clipped. Otherwise the effectiveness of the integrator will be reduced in turbulence // During climbout/takeoff, bias the demanded pitch angle so that zero speed error produces a pitch angle // demand equal to the minimum value (which is )set by the mission plan during this mode). Otherwise the // integrator has to catch up before the nose can be raised to reduce speed during climbout. float gainInv = (_integ5_state * timeConstant() * GRAVITY_MSS); float temp = SEB_error + SEBdot_error * _ptchDamp + SEBdot_dem * timeConstant(); if (_flight_stage == AP_TECS::FLIGHT_TAKEOFF) { temp += _PITCHminf * gainInv; } _integ7_state = constrain_float(_integ7_state, (gainInv * (_PITCHminf - 0.0783f)) - temp, (gainInv * (_PITCHmaxf + 0.0783f)) - temp); // Calculate pitch demand from specific energy balance signals _pitch_dem_unc = (temp + _integ7_state) / gainInv; // Constrain pitch demand _pitch_dem = constrain_float(_pitch_dem_unc, _PITCHminf, _PITCHmaxf); _pitch_dem = constrain_float(_pitch_dem_unc, _PITCHminf, _PITCHmaxf); // Rate limit the pitch demand to comply with specified vertical // acceleration limit float ptchRateIncr = _DT * _vertAccLim / _integ5_state; if ((_pitch_dem - _last_pitch_dem) > ptchRateIncr) { _pitch_dem = _last_pitch_dem + ptchRateIncr; } else if ((_pitch_dem - _last_pitch_dem) < -ptchRateIncr) { _pitch_dem = _last_pitch_dem - ptchRateIncr; } _last_pitch_dem = _pitch_dem; } void AP_TECS::_initialise_states(int32_t ptchMinCO_cd, float hgt_afe) { // Initialise states and variables if DT > 1 second or in climbout if (_DT > 1.0f) { _integ6_state = 0.0f; _integ7_state = 0.0f; _last_throttle_dem = aparm.throttle_cruise * 0.01f; _last_pitch_dem = _ahrs.pitch; _hgt_dem_adj_last = hgt_afe; _hgt_dem_adj = _hgt_dem_adj_last; _hgt_dem_prev = _hgt_dem_adj_last; _hgt_dem_in_old = _hgt_dem_adj_last; _TAS_dem_last = _TAS_dem; _TAS_dem_adj = _TAS_dem; _underspeed = false; _badDescent = false; _DT = 0.1f; // when first starting TECS, use a // small time constant } else if (_flight_stage == AP_TECS::FLIGHT_TAKEOFF) { _PITCHminf = 0.000174533f * ptchMinCO_cd; _THRminf = _THRmaxf - 0.01f; _hgt_dem_adj_last = hgt_afe; _hgt_dem_adj = _hgt_dem_adj_last; _hgt_dem_prev = _hgt_dem_adj_last; _TAS_dem_last = _TAS_dem; _TAS_dem_adj = _TAS_dem; _underspeed = false; _badDescent = false; } } void AP_TECS::_update_STE_rate_lim(void) { // Calculate Specific Total Energy Rate Limits // This is a trivial calculation at the moment but will get bigger once we start adding altitude effects _STEdot_max = _maxClimbRate * GRAVITY_MSS; _STEdot_min = - _minSinkRate * GRAVITY_MSS; } void AP_TECS::update_pitch_throttle(int32_t hgt_dem_cm, int32_t EAS_dem_cm, enum FlightStage flight_stage, int32_t ptchMinCO_cd, int16_t throttle_nudge, float hgt_afe) { // Calculate time in seconds since last update uint32_t now = hal.scheduler->micros(); _DT = max((now - _update_pitch_throttle_last_usec),0)*1.0e-6f; _update_pitch_throttle_last_usec = now; // Update the speed estimate using a 2nd order complementary filter _update_speed(); // Convert inputs _hgt_dem = hgt_dem_cm * 0.01f; _EAS_dem = EAS_dem_cm * 0.01f; _THRmaxf = aparm.throttle_max * 0.01f; _THRminf = aparm.throttle_min * 0.01f; // work out the maximum and minimum pitch // if TECS_PITCH_{MAX,MIN} isn't set then use // LIM_PITCH_{MAX,MIN}. Don't allow TECS_PITCH_{MAX,MIN} to be // larger than LIM_PITCH_{MAX,MIN} if (_pitch_max <= 0) { _PITCHmaxf = aparm.pitch_limit_max_cd * 0.01f; } else { _PITCHmaxf = min(_pitch_max, aparm.pitch_limit_max_cd * 0.01f); } if (_pitch_min >= 0) { _PITCHminf = aparm.pitch_limit_min_cd * 0.01f; } else { _PITCHminf = max(_pitch_min, aparm.pitch_limit_min_cd * 0.01f); } if (flight_stage == FLIGHT_LAND_FINAL) { // in flare use min pitch from LAND_PITCH_CD _PITCHminf = max(_PITCHminf, aparm.land_pitch_cd * 0.01f); // and allow zero throttle _THRminf = 0; } // convert to radians _PITCHmaxf = radians(_PITCHmaxf); _PITCHminf = radians(_PITCHminf); _flight_stage = flight_stage; // initialise selected states and variables if DT > 1 second or in climbout _initialise_states(ptchMinCO_cd, hgt_afe); // Calculate Specific Total Energy Rate Limits _update_STE_rate_lim(); // Calculate the speed demand _update_speed_demand(); // Calculate the height demand _update_height_demand(); // Detect underspeed condition _detect_underspeed(); // Calculate specific energy quantitiues _update_energies(); // Calculate throttle demand - use simple pitch to throttle if no airspeed sensor if (_ahrs.airspeed_sensor_enabled()) { _update_throttle(); } else { _update_throttle_option(throttle_nudge); } // Detect bad descent due to demanded airspeed being too high _detect_bad_descent(); // Calculate pitch demand _update_pitch(); // Write internal variables to the log_tuning structure. This // structure will be logged in dataflash at 10Hz log_tuning.hgt_dem = _hgt_dem_adj; log_tuning.hgt = _integ3_state; log_tuning.dhgt_dem = _hgt_rate_dem; log_tuning.dhgt = _climb_rate; log_tuning.spd_dem = _TAS_dem_adj; log_tuning.spd = _integ5_state; log_tuning.dspd = _vel_dot; log_tuning.ithr = _integ6_state; log_tuning.iptch = _integ7_state; log_tuning.thr = _throttle_dem; log_tuning.ptch = _pitch_dem; log_tuning.dspd_dem = _TAS_rate_dem; log_tuning.time_ms = hal.scheduler->millis(); } // log the contents of the log_tuning structure to dataflash void AP_TECS::log_data(DataFlash_Class &dataflash, uint8_t msgid) { log_tuning.head1 = HEAD_BYTE1; log_tuning.head2 = HEAD_BYTE2; log_tuning.msgid = msgid; dataflash.WriteBlock(&log_tuning, sizeof(log_tuning)); }