# hw definition file for processing by chibios_hwdef.py

# MCU class and specific type
MCU STM32F7xx STM32F777xx

# board ID for firmware load
APJ_BOARD_ID 141

# crystal frequency
OSCILLATOR_HZ 24000000

define STM32_LSECLK 32768U
define STM32_LSEDRV (3U << 3U)
define STM32_PLLSRC STM32_PLLSRC_HSE
define STM32_PLLM_VALUE 24
define STM32_PLLN_VALUE 432
define STM32_PLLP_VALUE 2
define STM32_PLLQ_VALUE 9

# board voltage
STM32_VDD 330U

FLASH_SIZE_KB 2048

# with 2M flash we can afford to optimize for speed
env OPTIMIZE -O2

# start on 4th sector (1st sector for bootloader, 2 for extra storage)
FLASH_RESERVE_START_KB 96

# fallback storage in case FRAM is not populated
define STORAGE_FLASH_PAGE 1

# this is the STM32 timer that ChibiOS will use for the low level
# driver. This must be a 32 bit timer, so Timers 2 or 5 on the STM32F777. 
# See hal_st_lld.c in ChibiOS for details

# ChibiOS system timer
STM32_ST_USE_TIMER 5

define HAL_STORAGE_SIZE 16384

# USB setup
USB_VENDOR 0x0483 # ST
USB_PRODUCT 0x5740
USB_STRING_MANUFACTURER "mRo"

# RC Input set for Interrupt not DMA
PC7 TIM3_CH2 TIM3 RCININT FLOAT LOW # also USART6_RX for serial RC

# Control of Spektrum power pin
PE4 SPEKTRUM_PWR OUTPUT LOW GPIO(70)
define HAL_GPIO_SPEKTRUM_PWR 70

# Spektrum Power is Active Low
define HAL_SPEKTRUM_PWR_ENABLED 0

# Spektrum RC Input pin, used as GPIO for bind for Satellite Receivers
PB0 SPEKTRUM_RC INPUT PULLUP GPIO(71)
define HAL_GPIO_SPEKTRUM_RC 71

# Order of I2C buses
I2C_ORDER I2C1

# this board only has a single I2C bus so make it external
define HAL_I2C_INTERNAL_MASK 0

# OEM Only
# I2C_ORDER I2C1, I2C2, I2C3

# order of UARTs (and USB)
# UART4 GPS
# USART2 FC
# USART3 FC
# UART8 FRSKY Telem
# USART6 FC
# UART7 DEBUG

UART_ORDER OTG1 UART4 USART2 USART3 UART8 USART6 UART7 OTG2

# default the 2nd interface to MAVLink2 until MissionPlanner updates drivers
define HAL_OTG2_PROTOCOL SerialProtocol_MAVLink2

# Another USART, this one for telem1. This one has RTS and CTS lines.
# USART2 telem1
PD3 USART2_CTS USART2
PD4 USART2_RTS USART2
PD5 USART2_TX USART2
PD6 USART2_RX USART2

# The telem2 USART, this one for telem2. This one has RTS and CTS lines.
# USART3 telem2
PD8 USART3_TX USART3
PD9 USART3_RX USART3
PD11 USART3_CTS USART3
PD12 USART3_RTS USART3

# UART4 GPS
PA0 UART4_TX UART4
PA1 UART4_RX UART4 NODMA

# USART6 Spare or can be configured as SPI6
PG14 USART6_TX USART6 NODMA
PG9 USART6_RX USART6 NODMA

# UART7 maps to uartF in the HAL (serial5 in SERIALn_ parameters). Debug Console
PE7 UART7_RX UART7 NODMA
PE8 UART7_TX UART7 NODMA

# UART8 FrSky Telemetry
PE0 UART8_RX UART8 NODMA
PE1 UART8_TX UART8 NODMA

# RSSI Analog Input
PC1 RSSI_IN ADC1

# Safety Switch Input
PC4 SAFETY_IN INPUT PULLDOWN

PA2 BATT_VOLTAGE_SENS ADC1 SCALE(1)
PA3 BATT_CURRENT_SENS ADC1 SCALE(1)

# Now the VDD sense pin. This is used to sense primary board voltage.
PA4 VDD_5V_SENS ADC1 SCALE(2)

#SPI1 ICM_20602 / ICM_20948
PA5 SPI1_SCK SPI1
PA6 SPI1_MISO SPI1
PA7 SPI1_MOSI SPI1

#SPI2 FRAM / DPS310
PB10 SPI2_SCK SPI2
PB14 SPI2_MISO SPI2
PB15 SPI2_MOSI SPI2

#SPI5 BMI088
PF7 SPI5_SCK SPI5
PF8 SPI5_MISO SPI5
PF9 SPI5_MOSI SPI5

# This is the pin that senses USB being connected. It is an input pin
# setup as OPENDRAIN.
PA9 VBUS INPUT OPENDRAIN

# This input pin is used to detect that power is valid on USB.
PC0 VBUS_VALID INPUT

# Now we define the pins that USB is connected on.
PA11 OTG_FS_DM OTG1
PA12 OTG_FS_DP OTG1

# These are the pins for SWD debugging with a STlinkv2 or black-magic probe.
PA13 JTMS-SWDIO SWD
PA14 JTCK-SWCLK SWD

# PWM output for buzzer
PA15 TIM2_CH1 TIM2 GPIO(77) ALARM

# Now the first I2C bus. The pin speeds are automatically setup
# correctly, but can be overridden here if needed.
PB8 I2C1_SCL I2C1
PB9 I2C1_SDA I2C1

# the 2nd I2C bus, OEM Only
# PB10 I2C2_SCL I2C2
# PB11 I2C2_SDA I2C2

# the 3nd I2C bus, OEM Only
# PB6 I2C4_SCL I2C4
# PB7 I2C4_SDA I2C4

# Now setup the pins for the microSD card, if available.
PC8 SDMMC_D0 SDMMC1
PC9 SDMMC_D1 SDMMC1
PC10 SDMMC_D2 SDMMC1
PC11 SDMMC_D3 SDMMC1
PC12 SDMMC_CK SDMMC1
PD2 SDMMC_CMD SDMMC1

# More CS pins for more sensors. The labels for all CS pins need to
# match the SPI device table later in this file.
PC2 ICM_20602_CS CS
PD7 BARO_CS CS
# The CS pin for FRAM (ramtron). This one is marked as using
# SPEED_VERYLOW, which matches the HAL_PX4 setup.
PD10 FRAM_CS CS SPEED_VERYLOW NODMA
PE15 ICM_20948_CS CS
PF10 BMI088_GYRO_CS CS
PF6 BMI088_ACCEL_CS CS

# the first CAN bus
PD0 CAN1_RX CAN1
PD1 CAN1_TX CAN1

PF5 GPIO_CAN1_SILENT OUTPUT PUSHPULL SPEED_LOW LOW GPIO(72)

# This defines the pins for the 2nd CAN interface, OEM Only.
# PB6 CAN2_TX CAN2
# PB4 CAN2_RX CAN2

# Now we start defining some PWM pins. We also map these pins to GPIO
# values, so users can set BRD_PWM_COUNT to choose how many of the PWM
# outputs on the primary MCU are setup as PWM and how many as
# GPIOs. To match HAL_PX4 we number the GPIOs for the PWM outputs
# starting at 50.
PE14 TIM1_CH4 TIM1 PWM(1) GPIO(50)
PE13 TIM1_CH3 TIM1 PWM(2) GPIO(51)
PE11 TIM1_CH2 TIM1 PWM(3) GPIO(52)
PE9  TIM1_CH1 TIM1 PWM(4) GPIO(53)
PD13 TIM4_CH2 TIM4 PWM(5) GPIO(54)
PD14 TIM4_CH3 TIM4 PWM(6) GPIO(55)
PI5  TIM8_CH1 TIM8 PWM(7) GPIO(56)
PI6  TIM8_CH2 TIM8 PWM(8) GPIO(57)

define BOARD_PWM_COUNT_DEFAULT 8

# This is the invensense data-ready pin. We don't use it in the
# default driver.
PD15 MPU_DRDY INPUT

# This is the pin to enable the sensors rail. It can be used to power
# cycle sensors to recover them in case there are problems with power on
# timing affecting sensor stability. We pull it high by default.
PE3 VDD_3V3_SENSORS_EN OUTPUT HIGH

# Power flag pins: these tell the MCU the status of the various power
# supplies that are available. The pin names need to exactly match the
# names used in AnalogIn.cpp. 
PB5 VDD_BRICK_VALID INPUT PULLUP

SPIDEV dps280      SPI2 DEVID3  BARO_CS           MODE3 10*MHZ 10*MHZ
SPIDEV ramtron     SPI2 DEVID10 FRAM_CS           MODE3  8*MHZ  8*MHZ
SPIDEV icm20948    SPI1 DEVID1  ICM_20948_CS      MODE3  2*MHZ  4*MHZ
SPIDEV icm20608    SPI1 DEVID2  ICM_20602_CS      MODE3  2*MHZ  8*MHZ
SPIDEV bmi088_g    SPI5 DEVID1  BMI088_GYRO_CS    MODE3 10*MHZ 10*MHZ
SPIDEV bmi088_a    SPI5 DEVID2  BMI088_ACCEL_CS   MODE3 10*MHZ 10*MHZ

# Now some defines for logging and terrain data files.
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"

# allow to have have a dedicated safety switch pin
define HAL_HAVE_SAFETY_SWITCH 1

# Enable RAMTROM parameter storage.
define HAL_WITH_RAMTRON 1

# Enable FAT filesystem support (needs a microSD defined via SDMMC).
define HAL_OS_FATFS_IO 1

# Enable RTSCTS support. You should define this if you have any UARTs with RTS/CTS pins.
define AP_FEATURE_RTSCTS 1

# Now setup the default battery pins driver analog pins and default
# scaling for the power brick.
define HAL_BATT_VOLT_PIN 2
define HAL_BATT_CURR_PIN 3
define HAL_BATT_VOLT_SCALE 10.1
define HAL_BATT_CURR_SCALE 17.0

# Control Zero has a TriColor LED, Red, Green, Blue
define HAL_HAVE_PIXRACER_LED

define HAL_GPIO_LED_ON  0
define HAL_GPIO_LED_OFF 1

# LED setup for PixracerLED driver
PB11 LED_R OUTPUT HIGH GPIO(0)
PB1  LED_G OUTPUT HIGH GPIO(1)
PB3  LED_B OUTPUT HIGH GPIO(2)

define HAL_GPIO_A_LED_PIN 0
define HAL_GPIO_B_LED_PIN 1
define HAL_GPIO_C_LED_PIN 2

DMA_PRIORITY SDMMC*
#DMA_NOSHARE SPI1* *
#DMA_NOSHARE SPI5* *

# 3 IMUs
IMU Invensensev2 SPI:icm20948 ROTATION_ROLL_180_YAW_90
IMU Invensense   SPI:icm20608 ROTATION_ROLL_180_YAW_90
IMU BMI088       SPI:bmi088_a SPI:bmi088_g ROTATION_NONE

# 1 baro
BARO DPS280      SPI:dps280

# 1 compass
COMPASS AK09916:probe_ICM20948 0 ROTATION_ROLL_180
define HAL_PROBE_EXTERNAL_I2C_COMPASSES