# hw definition file for processing by chibios_hwdef.py
# for the X-MAV-AP-H743V2 hardware

# MCU class and specific type
MCU STM32H7xx STM32H743xx

# board ID for firmware load
APJ_BOARD_ID AP_HW_X-MAV-AP-H743V2

# crystal frequency
OSCILLATOR_HZ 8000000

# ChibiOS system timer
STM32_ST_USE_TIMER 12
define CH_CFG_ST_RESOLUTION 16

# flash size
FLASH_SIZE_KB 2048
FLASH_RESERVE_START_KB 128

define HAL_STORAGE_SIZE 32768
STORAGE_FLASH_PAGE 14

# default to all pins low to avoid ESD issues
DEFAULTGPIO OUTPUT LOW PULLDOWN

# order of UARTs (and USB)
SERIAL_ORDER  OTG1 USART2 UART4 USART1 USART6 UART8 USART3 UART5 UART7  

# USB
PA11 OTG_FS_DM OTG1
PA12 OTG_FS_DP OTG1
PE15 VBUS INPUT OPENDRAIN

# Serial1
PD6 USART2_RX USART2
PD5 USART2_TX USART2

# Serial2
PB9 UART4_TX UART4
PB8 UART4_RX UART4

# GPS1/Serial3
PA9  USART1_TX USART1
PA10 USART1_RX USART1

# Serial4
PC6 USART6_TX USART6
PC7 USART6_RX USART6

# Serial5
PE0 UART8_RX UART8
PE1 UART8_TX UART8

# DJI O3/Serial6
PD8 USART3_TX USART3
PD9 USART3_RX USART3

# RC_INPUT/Serial7
PB13 UART5_TX UART5
PB12 UART5_RX UART5
PD14 SBUS_INV OUTPUT LOW

# ESC/Serial8
PE7 UART7_RX UART7

# SWD
PA13 JTMS-SWDIO SWD
PA14 JTCK-SWCLK SWD

# CAN
PD0 CAN1_RX CAN1
PD1 CAN1_TX CAN1

# two I2C bus
I2C_ORDER I2C1 I2C4

# I2C1 - baro
PB6 I2C1_SCL I2C1
PB7 I2C1_SDA I2C1

# I2C4 - CONNECTOR
PD12 I2C4_SCL I2C4
PD13 I2C4_SDA I2C4

# PWM output pins
PE9  TIM1_CH1 TIM1  PWM(1) GPIO(50) BIDIR
PE11 TIM1_CH2 TIM1  PWM(2) GPIO(51)
PE13 TIM1_CH3 TIM1  PWM(3) GPIO(52) BIDIR
PE14 TIM1_CH4 TIM1  PWM(4) GPIO(53)
PB1  TIM3_CH4 TIM3  PWM(5) GPIO(54) BIDIR
PB0  TIM3_CH3 TIM3  PWM(6) GPIO(55) 
PB10 TIM2_CH3 TIM2  PWM(7) GPIO(56) BIDIR
PB11 TIM2_CH4 TIM2  PWM(8) GPIO(57)

# GPIOs
PA4 PINIO1 OUTPUT GPIO(81) LOW
PC1 PINIO2 OUTPUT GPIO(82) LOW
PC0 PINIO3 OUTPUT GPIO(83) LOW

# LEDs
PD15 LED_RED   OUTPUT HIGH GPIO(90)
PD11 LED_GREEN OUTPUT HIGH GPIO(91)
PB15 LED_BLUE  OUTPUT HIGH GPIO(92)

define AP_NOTIFY_GPIO_LED_RGB_RED_PIN 90
define AP_NOTIFY_GPIO_LED_RGB_GREEN_PIN 91
define AP_NOTIFY_GPIO_LED_RGB_BLUE_PIN 92

define HAL_GPIO_LED_ON 1
define AP_NOTIFY_GPIO_LED_RGB_ENABLED 1

# ADC for Power
PC4 BATT_VOLTAGE_SENS ADC1 SCALE(1)
PC5 BATT_CURRENT_SENS ADC2 SCALE(1)

#BATTERY MONITOR ON
define BATT_MONITOR 4
define HAL_BATT_VOLT_PIN 4
define HAL_BATT_CURR_PIN 8
define HAL_BATT_VOLT_SCALE 10.2
define HAL_BATT_CURR_SCALE 20.4

# microSD support
PC12 SDMMC1_CK  SDMMC1
PD2  SDMMC1_CMD SDMMC1
PC8  SDMMC1_D0  SDMMC1
PC9  SDMMC1_D1  SDMMC1
PC10 SDMMC1_D2  SDMMC1
PC11 SDMMC1_D3  SDMMC1
define FATFS_HAL_DEVICE SDCD1

# SPI1 - IMU0
PA5 SPI1_SCK SPI1
PA6 SPI1_MISO SPI1
PA7 SPI1_MOSI SPI1
PA3 BMI088_1_G_CS CS
PA2 BMI088_1_A_CS CS

# SPI3 - CONNECTOR
PB3 SPI3_SCK  SPI3
PB4 SPI3_MISO SPI3
PB2 SPI3_MOSI SPI3
PA15 AT7456E_CS CS

# SPI4 - IMU1
PE6 SPI4_MOSI SPI4
PE2 SPI4_SCK  SPI4
PE5 SPI4_MISO SPI4
PC13 ICM42688P_CS CS

# barometers
BARO DPS310 I2C:0:0x76

# SPI devices
SPIDEV imu0_a      SPI1 DEVID1  BMI088_1_A_CS    MODE3  10*MHZ 10*MHZ
SPIDEV imu0_g      SPI1 DEVID2  BMI088_1_G_CS    MODE3  10*MHZ 10*MHZ
SPIDEV imu1        SPI4 DEVID3  ICM42688P_CS     MODE3  10*MHZ 10*MHZ
SPIDEV osd         SPI3 DEVID5  AT7456E_CS  MODE0  10*MHZ 10*MHZ

# 2 IMUs
IMU BMI088 SPI:imu0_a SPI:imu0_g ROTATION_ROLL_180_YAW_90
IMU Invensensev3 SPI:imu1 ROTATION_ROLL_180

# compasses
define HAL_COMPASS_DISABLE_IST8310_INTERNAL_PROBE
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
COMPASS IST8310 I2C:ALL_EXTERNAL:0x0E true  ROTATION_NONE
COMPASS IST8310 I2C:ALL_INTERNAL:0x0E false ROTATION_YAW_90

# enable FAT filesystem support (needs a microSD defined via SDMMC)
define HAL_OS_FATFS_IO 1

#Serial Port defaults
define DEFAULT_SERIAL4_PROTOCOL SerialProtocol_None
define DEFAULT_SERIAL6_PROTOCOL SerialProtocol_MSP_DisplayPort
define DEFAULT_SERIAL7_PROTOCOL SerialProtocol_RCIN
define DEFAULT_SERIAL8_PROTOCOL SerialProtocol_ESCTelemetry


# setup for OSD
define OSD_ENABLED 1
define HAL_OSD_TYPE_DEFAULT 5
ROMFS_WILDCARD libraries/AP_OSD/fonts/font*.bin