// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*- #if CLI_ENABLED == ENABLED // Functions called from the setup menu static int8_t setup_accel_scale (uint8_t argc, const Menu::arg *argv); static int8_t setup_batt_monitor (uint8_t argc, const Menu::arg *argv); static int8_t setup_compass (uint8_t argc, const Menu::arg *argv); static int8_t setup_compassmot (uint8_t argc, const Menu::arg *argv); static int8_t setup_declination (uint8_t argc, const Menu::arg *argv); static int8_t setup_erase (uint8_t argc, const Menu::arg *argv); static int8_t setup_frame (uint8_t argc, const Menu::arg *argv); #if FRAME_CONFIG == HELI_FRAME static int8_t setup_gyro (uint8_t argc, const Menu::arg *argv); static int8_t setup_heli (uint8_t argc, const Menu::arg *argv); #endif static int8_t setup_accel (uint8_t argc, const Menu::arg *argv); static int8_t setup_flightmodes (uint8_t argc, const Menu::arg *argv); static int8_t setup_optflow (uint8_t argc, const Menu::arg *argv); static int8_t setup_radio (uint8_t argc, const Menu::arg *argv); static int8_t setup_range (uint8_t argc, const Menu::arg *argv); static int8_t setup_factory (uint8_t argc, const Menu::arg *argv); static int8_t setup_set (uint8_t argc, const Menu::arg *argv); static int8_t setup_show (uint8_t argc, const Menu::arg *argv); static int8_t setup_sonar (uint8_t argc, const Menu::arg *argv); static int8_t setup_tune (uint8_t argc, const Menu::arg *argv); // Command/function table for the setup menu const struct Menu::command setup_menu_commands[] PROGMEM = { // command function called // ======= =============== {"accel", setup_accel_scale}, {"battery", setup_batt_monitor}, {"compass", setup_compass}, {"compassmot", setup_compassmot}, {"declination", setup_declination}, {"erase", setup_erase}, {"frame", setup_frame}, #if FRAME_CONFIG == HELI_FRAME {"gyro", setup_gyro}, {"heli", setup_heli}, #endif {"level", setup_accel}, {"modes", setup_flightmodes}, {"optflow", setup_optflow}, {"radio", setup_radio}, {"range", setup_range}, {"reset", setup_factory}, {"set", setup_set}, {"show", setup_show}, {"sonar", setup_sonar}, {"tune", setup_tune} }; // Create the setup menu object. MENU(setup_menu, "setup", setup_menu_commands); // Called from the top-level menu to run the setup menu. static int8_t setup_mode(uint8_t argc, const Menu::arg *argv) { // Give the user some guidance cliSerial->printf_P(PSTR("Setup Mode\n\n\n")); if(g.rc_1.radio_min >= 1300) { delay(1000); cliSerial->printf_P(PSTR("\n!Warning, radio not configured!")); delay(1000); cliSerial->printf_P(PSTR("\n Type 'radio' now.\n\n")); } // Run the setup menu. When the menu exits, we will return to the main menu. setup_menu.run(); return 0; } static int8_t setup_accel_scale(uint8_t argc, const Menu::arg *argv) { float trim_roll, trim_pitch; cliSerial->println_P(PSTR("Initialising gyros")); ahrs.init(); ins.init(AP_InertialSensor::COLD_START, ins_sample_rate, flash_leds); AP_InertialSensor_UserInteractStream interact(hal.console); if(ins.calibrate_accel(flash_leds, &interact, trim_roll, trim_pitch)) { // reset ahrs's trim to suggested values from calibration routine ahrs.set_trim(Vector3f(trim_roll, trim_pitch, 0)); } report_ins(); return(0); } static int8_t setup_batt_monitor(uint8_t argc, const Menu::arg *argv) { if (!strcmp_P(argv[1].str, PSTR("off"))) { g.battery_monitoring.set_and_save(0); } else if(argv[1].i > 0 && argv[1].i <= 4) { g.battery_monitoring.set_and_save(argv[1].i); } else { cliSerial->printf_P(PSTR("\nOp: off, 3-4")); } report_batt_monitor(); return 0; } static int8_t setup_compass(uint8_t argc, const Menu::arg *argv) { if (!strcmp_P(argv[1].str, PSTR("on"))) { g.compass_enabled.set_and_save(true); init_compass(); } else if (!strcmp_P(argv[1].str, PSTR("off"))) { Vector3f mag_offsets(0,0,0); compass.set_offsets(mag_offsets); compass.save_offsets(); g.compass_enabled.set_and_save(false); }else{ cliSerial->printf_P(PSTR("\nOp:[on,off]\n")); report_compass(); return 0; } g.compass_enabled.save(); report_compass(); return 0; } // setup_compassmot - sets compass's motor interference parameters static int8_t setup_compassmot(uint8_t argc, const Menu::arg *argv) { int8_t comp_type; // throttle or current based compensation Vector3f compass_base; // compass vector when throttle is zero Vector3f motor_impact; // impact of motors on compass vector Vector3f motor_impact_scaled; // impact of motors on compass vector scaled with throttle Vector3f motor_compensation; // final compensation to be stored to eeprom float throttle_pct; // throttle as a percentage 0.0 ~ 1.0 float throttle_pct_max = 0.0f; // maximum throttle reached (as a percentage 0~1.0) float current_amps_max = 0.0f; // maximum current reached float interference_pct; // interference as a percentage of total mag field (for reporting purposes only) uint32_t last_run_time; uint8_t print_counter = 49; bool updated = false; // have we updated the compensation vector at least once // default compensation type to use current if possible if( g.battery_monitoring == BATT_MONITOR_VOLTAGE_AND_CURRENT ) { comp_type = AP_COMPASS_MOT_COMP_CURRENT; }else{ comp_type = AP_COMPASS_MOT_COMP_THROTTLE; } // check if user wants throttle compensation if( !strcmp_P(argv[1].str, PSTR("t")) || !strcmp_P(argv[1].str, PSTR("T")) ) { comp_type = AP_COMPASS_MOT_COMP_THROTTLE; } // check if user wants current compensation if( !strcmp_P(argv[1].str, PSTR("c")) || !strcmp_P(argv[1].str, PSTR("C")) ) { comp_type = AP_COMPASS_MOT_COMP_CURRENT; } // check if radio is calibration pre_arm_rc_checks(); if(!ap.pre_arm_rc_check) { cliSerial->print_P(PSTR("radio not calibrated, exiting")); return 0; } // check compass is enabled if( !g.compass_enabled ) { cliSerial->print_P(PSTR("compass disabled, exiting")); return 0; } // check if we have a current monitor if( comp_type == AP_COMPASS_MOT_COMP_CURRENT && g.battery_monitoring != BATT_MONITOR_VOLTAGE_AND_CURRENT ) { cliSerial->print_P(PSTR("current monitor disabled, exiting")); return 0; } // initialise compass init_compass(); // disable motor compensation compass.motor_compensation_type(AP_COMPASS_MOT_COMP_DISABLED); compass.set_motor_compensation(Vector3f(0,0,0)); // print warning that motors will spin // ask user to raise throttle // inform how to stop test cliSerial->print_P(PSTR("This records the impact on the compass of running the motors. The motors will spin!\nHold throttle low, then raise to mid for 5 sec, then quickly back to low.\nAt any time you may press any key to exit.\n\nmeasuring compass vs ")); // inform what type of compensation we are attempting if( comp_type == AP_COMPASS_MOT_COMP_CURRENT ) { cliSerial->print_P(PSTR("CURRENT\n")); }else{ cliSerial->print_P(PSTR("THROTTLE\n")); } // clear out user input while( cliSerial->available() ) { cliSerial->read(); } // disable throttle and battery failsafe g.failsafe_throttle = FS_THR_DISABLED; g.failsafe_battery_enabled = false; // read radio read_radio(); // exit immediately if throttle is not zero if( g.rc_3.control_in != 0 ) { cliSerial->print_P(PSTR("throttle not zero, exiting\n")); return 0; } // get some initial compass readings last_run_time = millis(); while( millis() - last_run_time < 2000 ) { compass.accumulate(); } compass.read(); // exit immediately if the compass is not healthy if( !compass.healthy ) { cliSerial->print_P(PSTR("compass not healthy, exiting\n")); return 0; } // store initial x,y,z compass values compass_base.x = compass.mag_x; compass_base.y = compass.mag_y; compass_base.z = compass.mag_z; // initialise motor compensation motor_compensation = Vector3f(0,0,0); // clear out any user input while( cliSerial->available() ) { cliSerial->read(); } // enable motors and pass through throttle init_rc_out(); output_min(); motors.armed(true); // initialise run time last_run_time = millis(); // main run while there is no user input and the compass is healthy while(!cliSerial->available() && compass.healthy) { // 50hz loop if( millis() - last_run_time > 20 ) { last_run_time = millis(); // read radio input read_radio(); // pass through throttle to motors motors.throttle_pass_through(); // read some compass values compass.read(); // read current read_battery(); // calculate scaling for throttle throttle_pct = (float)g.rc_3.control_in / 1000.0f; throttle_pct = constrain_float(throttle_pct,0.0f,1.0f); // if throttle is zero, update base x,y,z values if( throttle_pct == 0.0f ) { compass_base.x = compass_base.x * 0.99f + (float)compass.mag_x * 0.01f; compass_base.y = compass_base.y * 0.99f + (float)compass.mag_y * 0.01f; compass_base.z = compass_base.z * 0.99f + (float)compass.mag_z * 0.01f; // causing printing to happen as soon as throttle is lifted print_counter = 49; }else{ // calculate diff from compass base and scale with throttle motor_impact.x = compass.mag_x - compass_base.x; motor_impact.y = compass.mag_y - compass_base.y; motor_impact.z = compass.mag_z - compass_base.z; // throttle based compensation if( comp_type == AP_COMPASS_MOT_COMP_THROTTLE ) { // scale by throttle motor_impact_scaled = motor_impact / throttle_pct; // adjust the motor compensation to negate the impact motor_compensation = motor_compensation * 0.99f - motor_impact_scaled * 0.01f; updated = true; }else{ // current based compensation if more than 3amps being drawn motor_impact_scaled = motor_impact / current_amps1; // adjust the motor compensation to negate the impact if drawing over 3amps if( current_amps1 >= 3.0f ) { motor_compensation = motor_compensation * 0.99f - motor_impact_scaled * 0.01f; updated = true; } } // record maximum throttle and current throttle_pct_max = max(throttle_pct_max, throttle_pct); current_amps_max = max(current_amps_max, current_amps1); // display output at 1hz if throttle is above zero print_counter++; if(print_counter >= 50) { print_counter = 0; cliSerial->printf_P(PSTR("thr:%d cur:%4.2f mot x:%4.1f y:%4.1f z:%4.1f comp x:%4.2f y:%4.2f z:%4.2f\n"),(int)g.rc_3.control_in, (float)current_amps1, (float)motor_impact.x, (float)motor_impact.y, (float)motor_impact.z, (float)motor_compensation.x, (float)motor_compensation.y, (float)motor_compensation.z); } } }else{ // grab some compass values compass.accumulate(); } } // stop motors motors.output_min(); motors.armed(false); // clear out any user input while( cliSerial->available() ) { cliSerial->read(); } // print one more time so the last thing printed matches what appears in the report_compass cliSerial->printf_P(PSTR("thr:%d cur:%4.2f mot x:%4.1f y:%4.1f z:%4.1f comp x:%4.2f y:%4.2f z:%4.2f\n"),(int)g.rc_3.control_in, (float)current_amps1, (float)motor_impact.x, (float)motor_impact.y, (float)motor_impact.z, (float)motor_compensation.x, (float)motor_compensation.y, (float)motor_compensation.z); // set and save motor compensation if( updated ) { compass.motor_compensation_type(comp_type); compass.set_motor_compensation(motor_compensation); compass.save_motor_compensation(); // calculate and display interference compensation at full throttle as % of total mag field if (comp_type == AP_COMPASS_MOT_COMP_THROTTLE) { // interference is impact@fullthrottle / mag field * 100 interference_pct = motor_compensation.length() / (float)COMPASS_MAGFIELD_EXPECTED * 100.0f; }else{ // interference is impact/amp * (max current seen / max throttle seen) / mag field * 100 interference_pct = motor_compensation.length() * (current_amps_max/throttle_pct_max) / (float)COMPASS_MAGFIELD_EXPECTED * 100.0f; } cliSerial->printf_P(PSTR("\nInterference at full throttle is %d%% of mag field\n\n"),(int)interference_pct); }else{ // compensation vector never updated, report failure cliSerial->printf_P(PSTR("Failed! Compensation disabled. Did you forget to raise the throttle high enough?")); compass.motor_compensation_type(AP_COMPASS_MOT_COMP_DISABLED); } // display new motor offsets and save report_compass(); return 0; } static int8_t setup_declination(uint8_t argc, const Menu::arg *argv) { compass.set_declination(radians(argv[1].f)); report_compass(); return 0; } static int8_t setup_erase(uint8_t argc, const Menu::arg *argv) { zero_eeprom(); return 0; } static int8_t setup_frame(uint8_t argc, const Menu::arg *argv) { if (!strcmp_P(argv[1].str, PSTR("x"))) { g.frame_orientation.set_and_save(X_FRAME); } else if (!strcmp_P(argv[1].str, PSTR("p"))) { g.frame_orientation.set_and_save(PLUS_FRAME); } else if (!strcmp_P(argv[1].str, PSTR("+"))) { g.frame_orientation.set_and_save(PLUS_FRAME); } else if (!strcmp_P(argv[1].str, PSTR("v"))) { g.frame_orientation.set_and_save(V_FRAME); }else{ cliSerial->printf_P(PSTR("\nOp:[x,+,v]\n")); report_frame(); return 0; } report_frame(); return 0; } #if FRAME_CONFIG == HELI_FRAME // setup for external tail gyro (for heli only) static int8_t setup_gyro(uint8_t argc, const Menu::arg *argv) { if (!strcmp_P(argv[1].str, PSTR("on"))) { motors.ext_gyro_enabled.set_and_save(true); // optionally capture the gain if( argc >= 2 && argv[2].i >= 1000 && argv[2].i <= 2000 ) { motors.ext_gyro_gain = argv[2].i; motors.ext_gyro_gain.save(); } } else if (!strcmp_P(argv[1].str, PSTR("off"))) { motors.ext_gyro_enabled.set_and_save(false); // capture gain if user simply provides a number } else if( argv[1].i >= 1000 && argv[1].i <= 2000 ) { motors.ext_gyro_enabled.set_and_save(true); motors.ext_gyro_gain = argv[1].i; motors.ext_gyro_gain.save(); }else{ cliSerial->printf_P(PSTR("\nOp:[on, off] gain\n")); } report_gyro(); return 0; } // Perform heli setup. // Called by the setup menu 'radio' command. static int8_t setup_heli(uint8_t argc, const Menu::arg *argv) { uint8_t active_servo = 0; int16_t value = 0; int16_t temp; int16_t state = 0; // 0 = set rev+pos, 1 = capture min/max int16_t max_roll=0, max_pitch=0, min_collective=0, max_collective=0, min_tail=0, max_tail=0; // initialise swash plate motors.init_swash(); // source swash plate movements directly from radio motors.servo_manual = true; // display initial settings report_heli(); // display help cliSerial->printf_P(PSTR("Instructions:")); print_divider(); cliSerial->printf_P(PSTR("\td\t\tdisplay settings\n")); cliSerial->printf_P(PSTR("\t1~4\t\tselect servo\n")); cliSerial->printf_P(PSTR("\ta or z\t\tmove mid up/down\n")); cliSerial->printf_P(PSTR("\tc\t\tset coll when blade pitch zero\n")); cliSerial->printf_P(PSTR("\tm\t\tset roll, pitch, coll min/max\n")); cliSerial->printf_P(PSTR("\tp\tset pos (i.e. p0 = front, p90 = right)\n")); cliSerial->printf_P(PSTR("\tr\t\treverse servo\n")); cliSerial->printf_P(PSTR("\tu a|d\t\tupdate rate (a=analog servo, d=digital)\n")); cliSerial->printf_P(PSTR("\tt\tset trim (-500 ~ 500)\n")); cliSerial->printf_P(PSTR("\tx\t\texit & save\n")); // start capturing while( value != 'x' ) { // read radio although we don't use it yet read_radio(); // allow swash plate to move motors.output_armed(); // record min/max if( state == 1 ) { if( abs(g.rc_1.control_in) > max_roll ) max_roll = abs(g.rc_1.control_in); if( abs(g.rc_2.control_in) > max_pitch ) max_pitch = abs(g.rc_2.control_in); if( g.rc_3.radio_out < min_collective ) min_collective = g.rc_3.radio_out; if( g.rc_3.radio_out > max_collective ) max_collective = g.rc_3.radio_out; min_tail = min(g.rc_4.radio_out, min_tail); max_tail = max(g.rc_4.radio_out, max_tail); } if( cliSerial->available() ) { value = cliSerial->read(); // process the user's input switch( value ) { case '1': active_servo = CH_1; break; case '2': active_servo = CH_2; break; case '3': active_servo = CH_3; break; case '4': active_servo = CH_4; break; case 'a': case 'A': heli_get_servo(active_servo)->radio_trim += 10; break; case 'c': case 'C': if( g.rc_3.radio_out >= 900 && g.rc_3.radio_out <= 2100 ) { motors.collective_mid = g.rc_3.radio_out; cliSerial->printf_P(PSTR("Collective when blade pitch at zero: %d\n"),(int)motors.collective_mid); } break; case 'd': case 'D': // display settings report_heli(); break; case 'm': case 'M': if( state == 0 ) { state = 1; // switch to capture min/max mode cliSerial->printf_P(PSTR("Move coll, roll, pitch and tail to extremes, press 'm' when done\n")); // reset servo ranges motors.roll_max = motors.pitch_max = 4500; motors.collective_min = 1000; motors.collective_max = 2000; motors._servo_4->radio_min = 1000; motors._servo_4->radio_max = 2000; // set sensible values in temp variables max_roll = abs(g.rc_1.control_in); max_pitch = abs(g.rc_2.control_in); min_collective = 2000; max_collective = 1000; min_tail = max_tail = abs(g.rc_4.radio_out); }else{ state = 0; // switch back to normal mode // double check values aren't totally terrible if( max_roll <= 1000 || max_pitch <= 1000 || (max_collective - min_collective < 200) || (max_tail - min_tail < 200) || min_tail < 1000 || max_tail > 2000 ) cliSerial->printf_P(PSTR("Invalid min/max captured roll:%d, pitch:%d, collective min: %d max: %d, tail min:%d max:%d\n"),max_roll,max_pitch,min_collective,max_collective,min_tail,max_tail); else{ motors.roll_max = max_roll; motors.pitch_max = max_pitch; motors.collective_min = min_collective; motors.collective_max = max_collective; motors._servo_4->radio_min = min_tail; motors._servo_4->radio_max = max_tail; // reinitialise swash motors.init_swash(); // display settings report_heli(); } } break; case 'p': case 'P': temp = read_num_from_serial(); if( temp >= -360 && temp <= 360 ) { if( active_servo == CH_1 ) motors.servo1_pos = temp; if( active_servo == CH_2 ) motors.servo2_pos = temp; if( active_servo == CH_3 ) motors.servo3_pos = temp; motors.init_swash(); cliSerial->printf_P(PSTR("Servo %d\t\tpos:%d\n"),active_servo+1, temp); } break; case 'r': case 'R': heli_get_servo(active_servo)->set_reverse(!heli_get_servo(active_servo)->get_reverse()); break; case 't': case 'T': temp = read_num_from_serial(); if( temp > 1000 ) temp -= 1500; if( temp > -500 && temp < 500 ) { heli_get_servo(active_servo)->radio_trim = 1500 + temp; motors.init_swash(); cliSerial->printf_P(PSTR("Servo %d\t\ttrim:%d\n"),active_servo+1, 1500 + temp); } break; case 'u': case 'U': temp = 0; // delay up to 2 seconds for servo type from user while( !cliSerial->available() && temp < 20 ) { temp++; delay(100); } if( cliSerial->available() ) { value = cliSerial->read(); if( value == 'a' || value == 'A' ) { g.rc_speed.set_and_save(AP_MOTORS_HELI_SPEED_ANALOG_SERVOS); //motors._speed_hz = AP_MOTORS_HELI_SPEED_ANALOG_SERVOS; // need to force this update to take effect immediately cliSerial->printf_P(PSTR("Analog Servo %dhz\n"),(int)g.rc_speed); } if( value == 'd' || value == 'D' ) { g.rc_speed.set_and_save(AP_MOTORS_HELI_SPEED_ANALOG_SERVOS); //motors._speed_hz = AP_MOTORS_HELI_SPEED_ANALOG_SERVOS; // need to force this update to take effect immediately cliSerial->printf_P(PSTR("Digital Servo %dhz\n"),(int)g.rc_speed); } } break; case 'z': case 'Z': heli_get_servo(active_servo)->radio_trim -= 10; break; } } delay(20); } // display final settings report_heli(); // save to eeprom motors._servo_1->save_eeprom(); motors._servo_2->save_eeprom(); motors._servo_3->save_eeprom(); motors._servo_4->save_eeprom(); motors.servo1_pos.save(); motors.servo2_pos.save(); motors.servo3_pos.save(); motors.roll_max.save(); motors.pitch_max.save(); motors.collective_min.save(); motors.collective_max.save(); motors.collective_mid.save(); // return swash plate movements to attitude controller motors.servo_manual = false; return(0); } #endif // FRAME_CONFIG == HELI static int8_t setup_accel(uint8_t argc, const Menu::arg *argv) { ahrs.init(); ins.init(AP_InertialSensor::COLD_START, ins_sample_rate, flash_leds); ins.init_accel(flash_leds); ahrs.set_trim(Vector3f(0,0,0)); // clear out saved trim report_ins(); return(0); } static int8_t setup_flightmodes(uint8_t argc, const Menu::arg *argv) { uint8_t _switchPosition = 0; uint8_t _oldSwitchPosition = 0; int8_t mode = 0; cliSerial->printf_P(PSTR("\nMode switch to edit, aileron: select modes, rudder: Simple on/off\n")); print_hit_enter(); while(1) { delay(20); read_radio(); _switchPosition = readSwitch(); // look for control switch change if (_oldSwitchPosition != _switchPosition) { mode = flight_modes[_switchPosition]; mode = constrain_int16(mode, 0, NUM_MODES-1); // update the user print_switch(_switchPosition, mode, BIT_IS_SET(g.simple_modes, _switchPosition)); // Remember switch position _oldSwitchPosition = _switchPosition; } // look for stick input if (abs(g.rc_1.control_in) > 3000) { mode++; if(mode >= NUM_MODES) mode = 0; // save new mode flight_modes[_switchPosition] = mode; // print new mode print_switch(_switchPosition, mode, BIT_IS_SET(g.simple_modes, _switchPosition)); delay(500); } // look for stick input if (g.rc_4.control_in > 3000) { g.simple_modes |= (1<<_switchPosition); // print new mode print_switch(_switchPosition, mode, BIT_IS_SET(g.simple_modes, _switchPosition)); delay(500); } // look for stick input if (g.rc_4.control_in < -3000) { g.simple_modes &= ~(1<<_switchPosition); // print new mode print_switch(_switchPosition, mode, BIT_IS_SET(g.simple_modes, _switchPosition)); delay(500); } // escape hatch if(cliSerial->available() > 0) { for (mode = 0; mode < 6; mode++) flight_modes[mode].save(); g.simple_modes.save(); print_done(); report_flight_modes(); return (0); } } } static int8_t setup_optflow(uint8_t argc, const Menu::arg *argv) { #if OPTFLOW == ENABLED if (!strcmp_P(argv[1].str, PSTR("on"))) { g.optflow_enabled = true; init_optflow(); } else if (!strcmp_P(argv[1].str, PSTR("off"))) { g.optflow_enabled = false; }else{ cliSerial->printf_P(PSTR("\nOp:[on, off]\n")); report_optflow(); return 0; } g.optflow_enabled.save(); report_optflow(); #endif // OPTFLOW == ENABLED return 0; } // Perform radio setup. // Called by the setup menu 'radio' command. static int8_t setup_radio(uint8_t argc, const Menu::arg *argv) { cliSerial->println_P(PSTR("\n\nRadio Setup:")); uint8_t i; for(i = 0; i < 100; i++) { delay(20); read_radio(); } if(g.rc_1.radio_in < 500) { while(1) { //cliSerial->printf_P(PSTR("\nNo radio; Check connectors.")); delay(1000); // stop here } } g.rc_1.radio_min = g.rc_1.radio_in; g.rc_2.radio_min = g.rc_2.radio_in; g.rc_3.radio_min = g.rc_3.radio_in; g.rc_4.radio_min = g.rc_4.radio_in; g.rc_5.radio_min = g.rc_5.radio_in; g.rc_6.radio_min = g.rc_6.radio_in; g.rc_7.radio_min = g.rc_7.radio_in; g.rc_8.radio_min = g.rc_8.radio_in; g.rc_1.radio_max = g.rc_1.radio_in; g.rc_2.radio_max = g.rc_2.radio_in; g.rc_3.radio_max = g.rc_3.radio_in; g.rc_4.radio_max = g.rc_4.radio_in; g.rc_5.radio_max = g.rc_5.radio_in; g.rc_6.radio_max = g.rc_6.radio_in; g.rc_7.radio_max = g.rc_7.radio_in; g.rc_8.radio_max = g.rc_8.radio_in; g.rc_1.radio_trim = g.rc_1.radio_in; g.rc_2.radio_trim = g.rc_2.radio_in; g.rc_4.radio_trim = g.rc_4.radio_in; // 3 is not trimed g.rc_5.radio_trim = 1500; g.rc_6.radio_trim = 1500; g.rc_7.radio_trim = 1500; g.rc_8.radio_trim = 1500; cliSerial->printf_P(PSTR("\nMove all controls to extremes. Enter to save: ")); while(1) { delay(20); // Filters radio input - adjust filters in the radio.pde file // ---------------------------------------------------------- read_radio(); g.rc_1.update_min_max(); g.rc_2.update_min_max(); g.rc_3.update_min_max(); g.rc_4.update_min_max(); g.rc_5.update_min_max(); g.rc_6.update_min_max(); g.rc_7.update_min_max(); g.rc_8.update_min_max(); if(cliSerial->available() > 0) { delay(20); while (cliSerial->read() != -1); /* flush */ g.rc_1.save_eeprom(); g.rc_2.save_eeprom(); g.rc_3.save_eeprom(); g.rc_4.save_eeprom(); g.rc_5.save_eeprom(); g.rc_6.save_eeprom(); g.rc_7.save_eeprom(); g.rc_8.save_eeprom(); print_done(); break; } } report_radio(); return(0); } static int8_t setup_range(uint8_t argc, const Menu::arg *argv) { cliSerial->printf_P(PSTR("\nCH 6 Ranges are divided by 1000: [low, high]\n")); g.radio_tuning_low.set_and_save(argv[1].i); g.radio_tuning_high.set_and_save(argv[2].i); report_tuning(); return 0; } // Initialise the EEPROM to 'factory' settings (mostly defined in APM_Config.h or via defaults). // Called by the setup menu 'factoryreset' command. static int8_t setup_factory(uint8_t argc, const Menu::arg *argv) { int16_t c; cliSerial->printf_P(PSTR("\n'Y' = factory reset, any other key to abort:\n")); do { c = cliSerial->read(); } while (-1 == c); if (('y' != c) && ('Y' != c)) return(-1); AP_Param::erase_all(); cliSerial->printf_P(PSTR("\nReboot APM")); delay(1000); for (;; ) { } // note, cannot actually return here return(0); } //Set a parameter to a specified value. It will cast the value to the current type of the //parameter and make sure it fits in case of INT8 and INT16 static int8_t setup_set(uint8_t argc, const Menu::arg *argv) { int8_t value_int8; int16_t value_int16; AP_Param *param; enum ap_var_type p_type; if(argc!=3) { cliSerial->printf_P(PSTR("Invalid command. Usage: set \n")); return 0; } param = AP_Param::find(argv[1].str, &p_type); if(!param) { cliSerial->printf_P(PSTR("Param not found: %s\n"), argv[1].str); return 0; } switch(p_type) { case AP_PARAM_INT8: value_int8 = (int8_t)(argv[2].i); if(argv[2].i!=value_int8) { cliSerial->printf_P(PSTR("Value out of range for type INT8\n")); return 0; } ((AP_Int8*)param)->set_and_save(value_int8); break; case AP_PARAM_INT16: value_int16 = (int16_t)(argv[2].i); if(argv[2].i!=value_int16) { cliSerial->printf_P(PSTR("Value out of range for type INT16\n")); return 0; } ((AP_Int16*)param)->set_and_save(value_int16); break; //int32 and float don't need bounds checking, just use the value provoded by Menu::arg case AP_PARAM_INT32: ((AP_Int32*)param)->set_and_save(argv[2].i); break; case AP_PARAM_FLOAT: ((AP_Float*)param)->set_and_save(argv[2].f); break; default: cliSerial->printf_P(PSTR("Cannot set parameter of type %d.\n"), p_type); break; } return 0; } // Print the current configuration. // Called by the setup menu 'show' command. static int8_t setup_show(uint8_t argc, const Menu::arg *argv) { AP_Param *param; ap_var_type type; //If a parameter name is given as an argument to show, print only that parameter if(argc>=2) { param=AP_Param::find(argv[1].str, &type); if(!param) { cliSerial->printf_P(PSTR("Parameter not found: '%s'\n"), argv[1]); return 0; } AP_Param::show(param, argv[1].str, type, cliSerial); return 0; } // clear the area print_blanks(8); report_version(); report_radio(); report_frame(); report_batt_monitor(); report_sonar(); report_flight_modes(); report_ins(); report_compass(); report_optflow(); #if FRAME_CONFIG == HELI_FRAME report_heli(); report_gyro(); #endif AP_Param::show_all(cliSerial); return(0); } static int8_t setup_sonar(uint8_t argc, const Menu::arg *argv) { if (!strcmp_P(argv[1].str, PSTR("on"))) { g.sonar_enabled.set_and_save(true); } else if (!strcmp_P(argv[1].str, PSTR("off"))) { g.sonar_enabled.set_and_save(false); } else if (argc > 1 && (argv[1].i >= 0 && argv[1].i <= 3)) { g.sonar_enabled.set_and_save(true); // if you set the sonar type, surely you want it on g.sonar_type.set_and_save(argv[1].i); }else{ cliSerial->printf_P(PSTR("\nOp:[on, off, 0-3]\n")); report_sonar(); return 0; } report_sonar(); return 0; } static int8_t setup_tune(uint8_t argc, const Menu::arg *argv) { g.radio_tuning.set_and_save(argv[1].i); report_tuning(); return 0; } /***************************************************************************/ // CLI reports /***************************************************************************/ static void report_batt_monitor() { cliSerial->printf_P(PSTR("\nBatt Mon:\n")); print_divider(); if(g.battery_monitoring == BATT_MONITOR_DISABLED) print_enabled(false); if(g.battery_monitoring == BATT_MONITOR_VOLTAGE_ONLY) cliSerial->printf_P(PSTR("volts")); if(g.battery_monitoring == BATT_MONITOR_VOLTAGE_AND_CURRENT) cliSerial->printf_P(PSTR("volts and cur")); print_blanks(2); } static void report_sonar() { cliSerial->printf_P(PSTR("Sonar\n")); print_divider(); print_enabled(g.sonar_enabled.get()); cliSerial->printf_P(PSTR("Type: %d (0=XL, 1=LV, 2=XLL, 3=HRLV)"), (int)g.sonar_type); print_blanks(2); } static void report_frame() { cliSerial->printf_P(PSTR("Frame\n")); print_divider(); #if FRAME_CONFIG == QUAD_FRAME cliSerial->printf_P(PSTR("Quad frame\n")); #elif FRAME_CONFIG == TRI_FRAME cliSerial->printf_P(PSTR("TRI frame\n")); #elif FRAME_CONFIG == HEXA_FRAME cliSerial->printf_P(PSTR("Hexa frame\n")); #elif FRAME_CONFIG == Y6_FRAME cliSerial->printf_P(PSTR("Y6 frame\n")); #elif FRAME_CONFIG == OCTA_FRAME cliSerial->printf_P(PSTR("Octa frame\n")); #elif FRAME_CONFIG == HELI_FRAME cliSerial->printf_P(PSTR("Heli frame\n")); #endif #if FRAME_CONFIG != HELI_FRAME if(g.frame_orientation == X_FRAME) cliSerial->printf_P(PSTR("X mode\n")); else if(g.frame_orientation == PLUS_FRAME) cliSerial->printf_P(PSTR("+ mode\n")); else if(g.frame_orientation == V_FRAME) cliSerial->printf_P(PSTR("V mode\n")); #endif print_blanks(2); } static void report_radio() { cliSerial->printf_P(PSTR("Radio\n")); print_divider(); // radio print_radio_values(); print_blanks(2); } static void report_ins() { cliSerial->printf_P(PSTR("INS\n")); print_divider(); print_gyro_offsets(); print_accel_offsets_and_scaling(); print_blanks(2); } static void report_compass() { cliSerial->printf_P(PSTR("Compass\n")); print_divider(); print_enabled(g.compass_enabled); // mag declination cliSerial->printf_P(PSTR("Mag Dec: %4.4f\n"), degrees(compass.get_declination())); Vector3f offsets = compass.get_offsets(); // mag offsets cliSerial->printf_P(PSTR("Mag off: %4.4f, %4.4f, %4.4f\n"), offsets.x, offsets.y, offsets.z); // motor compensation cliSerial->print_P(PSTR("Motor Comp: ")); if( compass.motor_compensation_type() == AP_COMPASS_MOT_COMP_DISABLED ) { cliSerial->print_P(PSTR("Off\n")); }else{ if( compass.motor_compensation_type() == AP_COMPASS_MOT_COMP_THROTTLE ) { cliSerial->print_P(PSTR("Throttle")); } if( compass.motor_compensation_type() == AP_COMPASS_MOT_COMP_CURRENT ) { cliSerial->print_P(PSTR("Current")); } Vector3f motor_compensation = compass.get_motor_compensation(); cliSerial->printf_P(PSTR("\nComp Vec: %4.2f, %4.2f, %4.2f\n"), motor_compensation.x, motor_compensation.y, motor_compensation.z); } print_blanks(1); } static void report_flight_modes() { cliSerial->printf_P(PSTR("Flight modes\n")); print_divider(); for(int16_t i = 0; i < 6; i++ ) { print_switch(i, flight_modes[i], BIT_IS_SET(g.simple_modes, i)); } print_blanks(2); } void report_optflow() { #if OPTFLOW == ENABLED cliSerial->printf_P(PSTR("OptFlow\n")); print_divider(); print_enabled(g.optflow_enabled); print_blanks(2); #endif // OPTFLOW == ENABLED } #if FRAME_CONFIG == HELI_FRAME static void report_heli() { cliSerial->printf_P(PSTR("Heli\n")); print_divider(); // main servo settings cliSerial->printf_P(PSTR("Servo \tpos \tmin \tmax \trev\n")); cliSerial->printf_P(PSTR("1:\t%d \t%d \t%d \t%d\n"),(int)motors.servo1_pos, (int)motors._servo_1->radio_min, (int)motors._servo_1->radio_max, (int)motors._servo_1->get_reverse()); cliSerial->printf_P(PSTR("2:\t%d \t%d \t%d \t%d\n"),(int)motors.servo2_pos, (int)motors._servo_2->radio_min, (int)motors._servo_2->radio_max, (int)motors._servo_2->get_reverse()); cliSerial->printf_P(PSTR("3:\t%d \t%d \t%d \t%d\n"),(int)motors.servo3_pos, (int)motors._servo_3->radio_min, (int)motors._servo_3->radio_max, (int)motors._servo_3->get_reverse()); cliSerial->printf_P(PSTR("tail:\t\t%d \t%d \t%d\n"), (int)motors._servo_4->radio_min, (int)motors._servo_4->radio_max, (int)motors._servo_4->get_reverse()); cliSerial->printf_P(PSTR("roll max: \t%d\n"), (int)motors.roll_max); cliSerial->printf_P(PSTR("pitch max: \t%d\n"), (int)motors.pitch_max); cliSerial->printf_P(PSTR("coll min:\t%d\t mid:%d\t max:%d\n"),(int)motors.collective_min, (int)motors.collective_mid, (int)motors.collective_max); // calculate and print servo rate cliSerial->printf_P(PSTR("servo rate:\t%d hz\n"),(int)g.rc_speed); print_blanks(2); } static void report_gyro() { cliSerial->printf_P(PSTR("Gyro:\n")); print_divider(); print_enabled( motors.ext_gyro_enabled ); if( motors.ext_gyro_enabled ) cliSerial->printf_P(PSTR("gain: %d"),(int)motors.ext_gyro_gain); print_blanks(2); } #endif // FRAME_CONFIG == HELI_FRAME /***************************************************************************/ // CLI utilities /***************************************************************************/ /*static void * print_PID(PI * pid) * { * cliSerial->printf_P(PSTR("P: %4.2f, I:%4.2f, IMAX:%ld\n"), * pid->kP(), * pid->kI(), * (long)pid->imax()); * } */ static void print_radio_values() { cliSerial->printf_P(PSTR("CH1: %d | %d\n"), (int)g.rc_1.radio_min, (int)g.rc_1.radio_max); cliSerial->printf_P(PSTR("CH2: %d | %d\n"), (int)g.rc_2.radio_min, (int)g.rc_2.radio_max); cliSerial->printf_P(PSTR("CH3: %d | %d\n"), (int)g.rc_3.radio_min, (int)g.rc_3.radio_max); cliSerial->printf_P(PSTR("CH4: %d | %d\n"), (int)g.rc_4.radio_min, (int)g.rc_4.radio_max); cliSerial->printf_P(PSTR("CH5: %d | %d\n"), (int)g.rc_5.radio_min, (int)g.rc_5.radio_max); cliSerial->printf_P(PSTR("CH6: %d | %d\n"), (int)g.rc_6.radio_min, (int)g.rc_6.radio_max); cliSerial->printf_P(PSTR("CH7: %d | %d\n"), (int)g.rc_7.radio_min, (int)g.rc_7.radio_max); cliSerial->printf_P(PSTR("CH8: %d | %d\n"), (int)g.rc_8.radio_min, (int)g.rc_8.radio_max); } static void print_switch(uint8_t p, uint8_t m, bool b) { cliSerial->printf_P(PSTR("Pos %d:\t"),p); print_flight_mode(cliSerial, m); cliSerial->printf_P(PSTR(",\t\tSimple: ")); if(b) cliSerial->printf_P(PSTR("ON\n")); else cliSerial->printf_P(PSTR("OFF\n")); } static void print_done() { cliSerial->printf_P(PSTR("\nSaved\n")); } static void zero_eeprom(void) { cliSerial->printf_P(PSTR("\nErasing EEPROM\n")); for (uint16_t i = 0; i < EEPROM_MAX_ADDR; i++) { hal.storage->write_byte(i, 0); } cliSerial->printf_P(PSTR("done\n")); } static void print_accel_offsets_and_scaling(void) { Vector3f accel_offsets = ins.get_accel_offsets(); Vector3f accel_scale = ins.get_accel_scale(); cliSerial->printf_P(PSTR("A_off: %4.2f, %4.2f, %4.2f\nA_scale: %4.2f, %4.2f, %4.2f\n"), (float)accel_offsets.x, // Pitch (float)accel_offsets.y, // Roll (float)accel_offsets.z, // YAW (float)accel_scale.x, // Pitch (float)accel_scale.y, // Roll (float)accel_scale.z); // YAW } static void print_gyro_offsets(void) { Vector3f gyro_offsets = ins.get_gyro_offsets(); cliSerial->printf_P(PSTR("G_off: %4.2f, %4.2f, %4.2f\n"), (float)gyro_offsets.x, (float)gyro_offsets.y, (float)gyro_offsets.z); } #if FRAME_CONFIG == HELI_FRAME static RC_Channel * heli_get_servo(int16_t servo_num){ if( servo_num == CH_1 ) return motors._servo_1; if( servo_num == CH_2 ) return motors._servo_2; if( servo_num == CH_3 ) return motors._servo_3; if( servo_num == CH_4 ) return motors._servo_4; return NULL; } // Used to read integer values from the serial port static int16_t read_num_from_serial() { uint8_t index = 0; uint8_t timeout = 0; char data[5] = ""; do { if (cliSerial->available() == 0) { delay(10); timeout++; }else{ data[index] = cliSerial->read(); timeout = 0; index++; } } while (timeout < 5 && index < 5); return atoi(data); } #endif #endif // CLI_ENABLED static void print_blanks(int16_t num) { while(num > 0) { num--; cliSerial->println(""); } } static void print_divider(void) { for (int i = 0; i < 40; i++) { cliSerial->print_P(PSTR("-")); } cliSerial->println(); } static void print_enabled(bool b) { if(b) cliSerial->print_P(PSTR("en")); else cliSerial->print_P(PSTR("dis")); cliSerial->print_P(PSTR("abled\n")); } static void init_esc() { // reduce update rate to motors to 50Hz motors.set_update_rate(50); // we enable the motors directly here instead of calling output_min because output_min would send a low signal to the ESC and disrupt the calibration process motors.enable(); motors.armed(true); while(1) { read_radio(); delay(100); notify.flags.esc_calibration = true; motors.throttle_pass_through(); } } static void report_version() { cliSerial->printf_P(PSTR("FW Ver: %d\n"),(int)g.k_format_version); print_divider(); print_blanks(2); } static void report_tuning() { cliSerial->printf_P(PSTR("\nTUNE:\n")); print_divider(); if (g.radio_tuning == 0) { print_enabled(g.radio_tuning.get()); }else{ float low = (float)g.radio_tuning_low.get() / 1000; float high = (float)g.radio_tuning_high.get() / 1000; cliSerial->printf_P(PSTR(" %d, Low:%1.4f, High:%1.4f\n"),(int)g.radio_tuning.get(), low, high); } print_blanks(2); }