# hw definition file for processing by chibios_hwdef.py
# for IFLIGHT_2RAW_H743 hardware.
# thanks to betaflight for pin information

# MCU class and specific type
MCU STM32H7xx STM32H743xx

# board ID for firmware load
APJ_BOARD_ID AP_HW_2RAWH743

# crystal frequency, setup to use external oscillator
OSCILLATOR_HZ 8000000

MCU_CLOCKRATE_MHZ 480

FLASH_SIZE_KB 2048

# bootloader takes first sector
FLASH_RESERVE_START_KB 384

define HAL_STORAGE_SIZE 16384
define STORAGE_FLASH_PAGE 1

STM32_ST_USE_TIMER 2

# SPI devices

# SPI1
PA5 SPI1_SCK SPI1
PA6 SPI1_MISO SPI1
PD7 SPI1_MOSI SPI1

# SPI2
PB13 SPI2_SCK SPI2
PB14 SPI2_MISO SPI2
PB15 SPI2_MOSI SPI2

# Chip select pins
PA15 SDCARD1_CS CS
PB12 OSD1_CS CS
PC15 GYRO1_CS CS

# SERIAL ports
SERIAL_ORDER OTG1 USART1 USART2 USART3 UART4 EMPTY USART6 OTG2
# PA10 IO-debug-console
PA11 OTG_FS_DM OTG1
PA12 OTG_FS_DP OTG1

# USART1 (VTX HD)
PA10 USART1_RX USART1
PA9 USART1_TX USART1
define DEFAULT_SERIAL1_PROTOCOL SerialProtocol_MSP_DisplayPort
define OSD_ENABLED 1
define HAL_OSD_TYPE_DEFAULT 5

# USART2 (RX)
PD5 USART2_TX USART2
PD6 USART2_RX USART2
define DEFAULT_SERIAL2_PROTOCOL SerialProtocol_RCIN

# USART3 (GPS)
PD8 USART3_TX USART3
PD9 USART3_RX USART3
define DEFAULT_SERIAL3_PROTOCOL SerialProtocol_GPS

# UART4 (GPS)
PB8 UART4_RX UART4
PB9 UART4_TX UART4
define DEFAULT_SERIAL4_PROTOCOL SerialProtocol_GPS

# USART6
PC6 USART6_TX USART6 NODMA
PC7 USART6_RX USART6 NODMA
define DEFAULT_SERIAL6_PROTOCOL SerialProtocol_ESCTelemetry

# I2C ports
I2C_ORDER I2C1 I2C2
# I2C1
PB6 I2C1_SCL I2C1
PB7 I2C1_SDA I2C1

# I2C2
PB10 I2C2_SCL I2C2
PB11 I2C2_SDA I2C2

# ADC ports

# ADC1
PC0 BATT_VOLTAGE_SENS ADC1 SCALE(1)
define HAL_BATT_VOLT_PIN 10
define HAL_BATT_VOLT_SCALE 11.0
PC1 BATT_CURRENT_SENS ADC1 SCALE(1)
define HAL_BATT_CURR_PIN 11
define HAL_BATT_CURR_SCALE 40.0
PC5 RSSI_ADC ADC1
define BOARD_RSSI_ANA_PIN 8
define HAL_BATT_MONITOR_DEFAULT 4

# MOTORS
PB0 TIM3_CH3 TIM3 PWM(1) GPIO(50) BIDIR # M1
PB1 TIM3_CH4 TIM3 PWM(2) GPIO(51)       # M2
PA0 TIM5_CH1 TIM5 PWM(3) GPIO(52) BIDIR # M3
PA1 TIM5_CH2 TIM5 PWM(4) GPIO(53)       # M4
PA2 TIM5_CH3 TIM5 PWM(5) GPIO(54) BIDIR # M5
PA3 TIM5_CH4 TIM5 PWM(6) GPIO(55)       # M6
PD12 TIM4_CH1 TIM4 PWM(7) GPIO(56) BIDIR # M7
PD13 TIM4_CH2 TIM4 PWM(8) GPIO(57)       # M8

# LEDs
PA8 TIM1_CH1 TIM1 PWM(9) GPIO(58) # M9

# VTX power switch
PD10 VTX_PWR OUTPUT LOW GPIO(81)
define RELAY2_PIN_DEFAULT 81

define AP_NOTIFY_GPIO_LED_2_ENABLED 1
PE3 LED0 OUTPUT LOW GPIO(90)
define HAL_GPIO_A_LED_PIN 90

PE4 LED1 OUTPUT LOW GPIO(91)
define HAL_GPIO_B_LED_PIN 91

BARO SPL06 I2C:1:0x76

# IMU setup

# IMU setup
SPIDEV imu1   SPI1 DEVID1 GYRO1_CS   MODE3   1*MHZ   16*MHZ
IMU Invensensev3 SPI:imu1 ROTATION_ROLL_180

DMA_NOSHARE TIM3_UP TIM5_UP TIM4_UP SPI1*
DMA_PRIORITY TIM3_UP TIM5_UP TIM4_UP SPI1*

# no built-in compass, but probe the i2c bus for all possible
# external compass types
define ALLOW_ARM_NO_COMPASS
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
define HAL_I2C_INTERNAL_MASK 0
define HAL_COMPASS_AUTO_ROT_DEFAULT 2
define HAL_DEFAULT_INS_FAST_SAMPLE 1
# Motor order implies Betaflight/X for standard ESCs
define HAL_FRAME_TYPE_DEFAULT 12