diff --git a/Tools/bootloaders/JFB110_bl.bin b/Tools/bootloaders/JFB110_bl.bin new file mode 100755 index 0000000000..06d3969c94 Binary files /dev/null and b/Tools/bootloaders/JFB110_bl.bin differ diff --git a/libraries/AP_HAL_ChibiOS/hwdef/JFB110/README.md b/libraries/AP_HAL_ChibiOS/hwdef/JFB110/README.md new file mode 100644 index 0000000000..87f58272ae --- /dev/null +++ b/libraries/AP_HAL_ChibiOS/hwdef/JFB110/README.md @@ -0,0 +1,140 @@ +# JFB-110 Flight Controller + +The JFB-110 flight controller is sold by [JAE](https://www.jae.com/Motion_Sensor_Control/eVTOL/FlightController/) + +## Features + + - STM32H755 microcontroller + - Three IMUs: SCHA63T and IIM42652 x2 + - Two BAROs: MS5611 SPI barometer x2 + - builtin I2C IST8310 magnetometer + - microSD card slot + - 5 UARTs plus USB, RCIN, SBUS_OUT + - 16 PWM outputs + - Four I2C and two CAN ports + - External Buzzer (Open/Drain and 33V Out) + - external safety Switch + - voltage monitoring for servo rail and Vcc + - two dedicated power input ports for external power bricks + +## UART Mapping + + - SERIAL0 -> USB + - SERIAL1 -> UART7 (Telem1) + - SERIAL2 -> UART5 (Telem2) + - SERIAL3 -> USART1 (GPS) + - SERIAL4 -> UART4 (GPS2, marked UART/I2CB) + - SERIAL5 -> USART6 (RCIN) + - SERIAL6 -> UART8 (SBUS_OUT) + - SERIAL7 -> USART3 (debug) + - SERIAL8 -> USB (SLCAN) + + +The Telem1 and Telem2 ports have RTS/CTS pins, the other UARTs do not +have RTS/CTS. + +The USART3 connector is labelled debug, but is available as a general +purpose UART with ArduPilot. + +## RC Input + +RC input is configured on the port marked DSM/SBUS RC. This connector +supports all RC protocols. Two cables are available for this port. To +use software binding of Spektrum satellite receivers you need to use +the Spektrum satellite cable. + +## PWM Output + +The JFB-110 supports up to 16 PWM outputs. +These are directly attached to the STM32H755 and support all +PWM protocols. + +The 16 PWM outputs are in 6 groups: + - PWM 1 and 2 in group1 (TIM15) + - PWM 3 and 4 in group2 (TIM3) + - PWM 5, 11 ,12 and 13 in group3 (TIM4) + - PWM 6 ,9 and 10 in group4 (TIM1) + - PWM 7 ,8 and 15 in group5 (TIM5) + - PWM 14 and 16 in group6 (TIM12) + +Channels within the same group need to use the same output rate. If +any channel in a group uses DShot then all channels in the group need +to use DShot. + +## Battery Monitoring + +The board has two dedicated power monitor ports on 8 pin +connectors. The correct battery setting parameters are dependent on +the type of power brick which is connected. +Recomended input voltage is 4.9 to 5.5 volt. + +## Compass + +The JFB-110 has a builtin IST8310 compass. Due to potential +interference the board is usually used with an external I2C compass as +part of a GPS/Compass combination. + +## GPIOs + +The 16 PWM ports can be used as GPIOs (relays, buttons, RPM etc). To +use them you need to limit the number of these pins that is used for +PWM by setting the BRD_PWM_COUNT to a number less than 6. For example +if you set BRD_PWM_COUNT to 4 then PWM5 and PWM6 will be available for +use as GPIOs. + +The numbering of the GPIOs for PIN variables in ArduPilot is: + - PWM(1) 50 + - PWM(2) 51 + - PWM(3) 52 + - PWM(4) 53 + - PWM(5) 54 + - PWM(6) 55 + - PWM(7) 56 + - PWM(8) 57 + - PWM(9) 58 + - PWM(10) 59 + - PWM(11) 60 + - PWM(12) 61 + - PWM(13) 62 + - PWM(14) 63 + - PWM(15) 64 + - PWM(16) 65 + - FMU_CAP1 66 + - FMU_CAP2 67 + + +## Analog inputs + +The JFB-110 has 9 analog inputs + - ADC Pin16 -> Battery Voltage + - ADC Pin18 -> Battery Current Sensor + - ADC Pin9 -> Battery Voltage 2 + - ADC Pin6 -> Battery Current Sensor 2 + - ADC Pin5 -> ADC 5V Sense + - ADC Pin11 -> ADC 3.3V Sense + - ADC Pin10 -> RSSI voltage monitoring + - ADC Pin12 -> ADC SPARE 1 + - ADC Pin13 -> ADC SPARE 2 + +## I2C Buses + +The JFB-110 has 4 I2C interfaces. +I2C 3 is for internal only. + - the internal I2C port is bus 3 in ArduPilot (I2C3 in hardware) + - the port labelled I2CA is bus 4 in ArduPilot (I2C4 in hardware) + - the port labelled I2CB is bus 2 in ArduPilot (I2C2 in hardware) + - the port labelled GPS is bus 1 in ArduPilot (I2C1 in hardware) + +## CAN + +The JFB-110 has two independent CAN buses, with the following pinouts. + +## Debug + +The JFB-110 supports SWD debugging on the debug port + +## Loading Firmware + +The board comes pre-installed with an ArduPilot compatible bootloader, +allowing the loading of *.apj firmware files with any ArduPilot +compatible ground station. diff --git a/libraries/AP_HAL_ChibiOS/hwdef/JFB110/defaults.parm b/libraries/AP_HAL_ChibiOS/hwdef/JFB110/defaults.parm new file mode 100644 index 0000000000..0be0b0db51 --- /dev/null +++ b/libraries/AP_HAL_ChibiOS/hwdef/JFB110/defaults.parm @@ -0,0 +1,28 @@ +# board setting +BRD_VBUS_MIN 4.9 + +# setup SERIAL4 for BPort +SERIAL4_BAUD 57 +SERIAL4_PROTOCOL -1 +SERIAL4_OPTIONS 0 +# setup SERIAL5 to RCIN +SERIAL5_BAUD 100 +SERIAL5_PROTOCOL 23 +SERIAL5_OPTIONS 3 +# setup SERIAL6 to SBUS OUT +SERIAL6_BAUD 100 +SERIAL6_PROTOCOL 15 +SERIAL6_OPTIONS 3 +# setup SERIAL7 for debug console +SERIAL7_BAUD 921 +SERIAL7_PROTOCOL 0 +SERIAL7_OPTIONS 0 + +#Three IMU Setting +EK3_IMU_MASK 7 +INS_ENABLE_MASK 7 + +#RSSI Setting +RSSI_TYPE 1 +RSSI_ANA_PIN 10 + diff --git a/libraries/AP_HAL_ChibiOS/hwdef/JFB110/hwdef-bl.dat b/libraries/AP_HAL_ChibiOS/hwdef/JFB110/hwdef-bl.dat new file mode 100644 index 0000000000..6a7b2f739b --- /dev/null +++ b/libraries/AP_HAL_ChibiOS/hwdef/JFB110/hwdef-bl.dat @@ -0,0 +1,139 @@ +# hw definition file for processing by chibios_hwdef.py +# for the JFB110 hardware + +# board ID for firmware load +APJ_BOARD_ID 1110 + +# MCU class and specific type +MCU STM32H7xx STM32H755xx +define CORE_CM7 +#define SMPS_PWR + +# crystal frequency 24MHz +OSCILLATOR_HZ 24000000 + +# the location where the bootloader will put the firmware +# bootloader is installed at zero offset +FLASH_RESERVE_START_KB 0 +# the H755 has 128k sectors +FLASH_BOOTLOADER_LOAD_KB 128 +# with 2M flash we can afford to optimize for speed +FLASH_SIZE_KB 2048 +HAL_STORAGE_SIZE 32768 + +env OPTIMIZE -Os + +# ChibiOS system timer +STM32_ST_USE_TIMER 2 + +# USB setup +# USB_VENDOR 0x0A8E # JAE +# USB_PRODUCT 0x8888 # This is temp Number +USB_STRING_MANUFACTURER "Japan Aviation Electronics Industry Ltd." +USB_STRING_PRODUCT "JFB-110" + +# order of UARTs (and USB) +SERIAL_ORDER OTG1 UART7 UART5 USART3 + +# serial port for stdout, set SERIAL7_PROTOCOL 0(none) when using +# The value for STDOUT_SERIAL is a serial device name, and must be for a +# serial device for which pins are defined in this file. For example, SD3 +# is for USART3 (SD3 == "serial device 3" in ChibiOS). +STDOUT_SERIAL SD3 +STDOUT_BAUDRATE 921600 + +# default to all pins low to avoid ESD issues +DEFAULTGPIO OUTPUT LOW PULLDOWN + +# USB OTG1 SERIAL0 +PA11 OTG_FS_DM OTG1 +PA12 OTG_FS_DP OTG1 + +# pins for SWD debugging +PA13 JTMS-SWDIO SWD +PA14 JTCK-SWCLK SWD + +# CS pins +PH3 SCHA63T_G_CS CS # SPI1_CS1 +PH4 SCHA63T_A_CS CS # SPI1_CS2 +PH5 MS5611_2_CS CS # SPI1_CS3 +PG6 AT25512_CS CS # SPI1_CS4 +PG7 FRAM_CS CS # SPI3_CS1 +PF10 IIM42652_1_CS CS # SPI3_CS2 +PH15 MS5611_1_CS CS # SPI4_CS1 +PG15 IIM42652_2_CS CS # SPI4_CS2 + +# telem1 +PE8 UART7_TX UART7 +PE10 UART7_CTS UART7 +PF6 UART7_RX UART7 +PF8 UART7_RTS UART7 + +# telem2 +PC12 UART5_TX UART5 +PC9 UART5_CTS UART5 +PD2 UART5_RX UART5 +PC8 UART5_RTS UART5 + +# debug uart +PD8 USART3_TX USART3 NODMA +PD9 USART3_RX USART3 NODMA + +# armed indication +PB10 nARMED OUTPUT HIGH # TP8 + +# This defines an output pin which will default to output HIGH. It is +# a pin that enables peripheral power on this board. It starts in the +# off state, then is pulled low to enable peripherals in +# peripheral_power_enable() +PG10 nVDD_5V_HIPOWER_EN OUTPUT HIGH +PG4 nVDD_5V_PERIPH_EN OUTPUT HIGH +PG12 VDD_3V3_SENSORS_EN OUTPUT LOW +PD4 VDD_3V3_SENSORS2_EN OUTPUT LOW +PD3 VDD_3V3_SENSORS3_EN OUTPUT LOW +#VDD_3V3_SENSORS4_EN OUTPUT LOW +#VDD_3V3_SD_CARD_EN OUTPUT LOW + +# PWM output pins +# we need to disable DMA on the last 2 FMU channels +# as timer 12 doesn't have a TIMn_UP DMA option +PA2 PWMOUT1 OUTPUT LOW +PE6 PWMOUT2 OUTPUT LOW +PA7 PWMOUT3 OUTPUT LOW +PA6 PWMOUT4 OUTPUT LOW +PD15 PWMOUT5 OUTPUT LOW +PE9 PWMOUT6 OUTPUT LOW +PH11 PWMOUT7 OUTPUT LOW +PH10 PWMOUT8 OUTPUT LOW +PA10 PWMOUT9 OUTPUT LOW +PA9 PWMOUT10 OUTPUT LOW +PD14 PWMOUT11 OUTPUT LOW +PD13 PWMOUT12 OUTPUT LOW +PD12 PWMOUT13 OUTPUT LOW +PH9 PWMOUT14 OUTPUT LOW +PH12 PWMOUT15 OUTPUT LOW +PH6 PWMOUT16 OUTPUT LOW +PD11 PWM_OE OUTPUT HIGH +PD5 PWM_OE2 OUTPUT HIGH + +# controlled manually +PG13 GPIO_CAN1_SILENT OUTPUT PUSHPULL HIGH +PG8 GPIO_CAN2_SILENT OUTPUT PUSHPULL HIGH + +# Control of Spektrum power pin +PH2 SPEKTRUM_PWR OUTPUT LOW GPIO(69) + +# LEDs +#PE3 LED_RED OUTPUT OPENDRAIN GPIO(70) HIGH +##PE4 LED_GREEN OUTPUT OPENDRAIN GPIO(71) LOW +##PE5 LED_BLUE OUTPUT OPENDRAIN GPIO(72) LOW + +PE4 LED_BOOTLOADER OUTPUT HIGH +PE5 LED_ACTIVITY OUTPUT HIGH +define HAL_LED_ON 0 + +#define HAL_USE_EMPTY_STORAGE 1 +#define HAL_STORAGE_SIZE 32768 + +# enable DFU by default +#ENABLE_DFU_BOOT 1 diff --git a/libraries/AP_HAL_ChibiOS/hwdef/JFB110/hwdef.dat b/libraries/AP_HAL_ChibiOS/hwdef/JFB110/hwdef.dat new file mode 100644 index 0000000000..6b8189410a --- /dev/null +++ b/libraries/AP_HAL_ChibiOS/hwdef/JFB110/hwdef.dat @@ -0,0 +1,352 @@ +# hw definition file for processing by chibios_hwdef.py +# for the JFB110 hardware + +# board ID for firmware load +APJ_BOARD_ID 1110 + +# MCU class and specific type +MCU STM32H7xx STM32H755xx +define CORE_CM7 +#define SMPS_PWR + +# crystal frequency 24MHz +OSCILLATOR_HZ 24000000 + +# the H755 has 128k sectors +# bootloader is installed at 128kb offset +FLASH_BOOTLOADER_LOAD_KB 128 +FLASH_RESERVE_START_KB 128 +FLASH_SIZE_KB 2048 +HAL_STORAGE_SIZE 32768 + +# USB setup +# USB_VENDOR 0x0A8E # JAE +USB_STRING_MANUFACTURER "Japan Aviation Electronics Industry Ltd." +USB_STRING_PRODUCT "JFB-110" + +# ChibiOS system timer +STM32_ST_USE_TIMER 2 + +# enable board sub-type detection +define CONFIG_HAL_BOARD HAL_BOARD_CHIBIOS +#define HAL_CHIBIOS_ARCH_FMUV6 1 +#define AP_FEATURE_BOARD_DETECT 1 +#define CONFIG_HAL_BOARD_SUBTYPE HAL_BOARD_SUBTYPE_CHIBIOS_FMUV5 +#define HAL_CHIBIOS_ARCH_FMUV5 1 + +env OPTIMIZE -O2 + +# order of UARTs (and USB) +# SERIAL | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | +SERIAL_ORDER OTG1 UART7 UART5 USART1 UART4 USART6 UART8 USART3 OTG2 +#USART6 is RX only for SBUS_IN +#UART8 is TX only for SBUS_OUT + +# serial port for stdout, set SERIAL7_PROTOCOL 5(GPS) when using +# The value for STDOUT_SERIAL is a serial device name, and must be for a +# serial device for which pins are defined in this file. For example, SD3 +# is for USART3 (SD3 == "serial device 3" in ChibiOS). +STDOUT_SERIAL SD3 +STDOUT_BAUDRATE 921600 + +# default to all pins low to avoid ESD issues +DEFAULTGPIO OUTPUT LOW PULLDOWN + +# USB OTG1 SERIAL0 +PA11 OTG_FS_DM OTG1 +PA12 OTG_FS_DP OTG1 +# default the 2nd interface to MAVLink2 +define HAL_OTG2_PROTOCOL SerialProtocol_MAVLink2 + +# pins for SWD debugging +PA13 JTMS-SWDIO SWD +PA14 JTCK-SWCLK SWD + +# telem1 +PE8 UART7_TX UART7 SPEED_VERYLOW +PE10 UART7_CTS UART7 SPEED_VERYLOW +PF6 UART7_RX UART7 SPEED_VERYLOW +PF8 UART7_RTS UART7 SPEED_VERYLOW + +# telem2 +PC12 UART5_TX UART5 SPEED_VERYLOW +PC9 UART5_CTS UART5 SPEED_VERYLOW +PD2 UART5_RX UART5 SPEED_VERYLOW +PC8 UART5_RTS UART5 SPEED_VERYLOW + +# telem3 for future use +#PD5 TP14 OUTPUT LOW #TP14 + +# GPS1 +PB6 USART1_TX USART1 SPEED_VERYLOW +PB7 USART1_RX USART1 SPEED_VERYLOW + +# uart4 +PH13 UART4_TX UART4 SPEED_VERYLOW +PH14 UART4_RX UART4 SPEED_VERYLOW + +# TX Only, for SBUS OUT +PE0 UART8_RX UART8 SPEED_VERYLOW #TP3 +PE1 UART8_TX UART8 SPEED_VERYLOW + +# RX only, for RC input +#PG14 USART6_TX USART6 SPEED_VERYLOW #TP10 +PC7 USART6_RX USART6 SPEED_VERYLOW + +# debug uart +PD8 USART3_TX USART3 SPEED_VERYLOW NODMA +PD9 USART3_RX USART3 SPEED_VERYLOW NODMA + +# ADC +PA0 BATT_VOLTAGE_SENS ADC1 SCALE(1) # ADC1_16 +PF12 BATT_CURRENT_SENS ADC1 SCALE(1) # ADC1_6 +PB0 BATT2_VOLTAGE_SENS ADC1 SCALE(1) # ADC1_9 +PA4 BATT2_CURRENT_SENS ADC1 SCALE(1) # ADC1_18 + +# setup scaling defaults for supplied power brick +define HAL_BATT_VOLT_SCALE 1 #18.182 +define HAL_BATT_CURR_SCALE 1 #36.364 +define HAL_BATT2_VOLT_SCALE 1 #18.182 +define HAL_BATT2_CURR_SCALE 1 #36.364 +define HAL_BATT_VOLT_PIN 16 +define HAL_BATT_CURR_PIN 6 +define HAL_BATT2_VOLT_PIN 9 +define HAL_BATT2_CURR_PIN 18 + +# Now the VDD sense pin. This is used to sense primary board voltage. +PB1 VDD_5V_SENS ADC1 SCALE(2) # ADC1_5 +define ANALOG_VCC_5V_PIN 5 +define HAL_HAVE_BOARD_VOLTAGE 1 +PB3 VBUS_RESERVED INPUT + +# JFB110 has SERVORAIL ADC +# Set SENSOR_3.3V power signal insted. +PC1 SCALED_V3V3 ADC1 SCALE(2) # ADC1_11 +PA3 FMU_SERVORAIL_VCC ADC1 SCALE(2) # ADC1_15 +define FMU_SERVORAIL_ADC_PIN 15 +define HAL_HAVE_SERVO_VOLTAGE 1 + +PC0 RSSI_IN ADC1 SCALE(1) # ADC1_10 +define RSSI_ANA_PIN 10 + +PC2 ADC1_6V6 ADC1 SCALE(2) # ADC1_12 +PC3 ADC1_3V3 ADC1 SCALE(1) # ADC1_13 + +# This defines an output pin which will default to output HIGH. It is +# a pin that enables peripheral power on this board. It starts in the +# off state, then is pulled low to enable peripherals in +# peripheral_power_enable() +PG10 nVDD_5V_HIPOWER_EN OUTPUT HIGH +PG4 nVDD_5V_PERIPH_EN OUTPUT HIGH +PG12 VDD_3V3_SENSORS_EN OUTPUT LOW +PD4 VDD_3V3_SENSORS2_EN OUTPUT LOW +PD3 VDD_3V3_SENSORS3_EN OUTPUT LOW +#VDD_3V3_SENSORS4_EN OUTPUT LOW +#VDD_3V3_SD_CARD_EN OUTPUT LOW + +# controlled manually +PG13 GPIO_CAN1_SILENT OUTPUT PUSHPULL LOW +PG8 GPIO_CAN2_SILENT OUTPUT PUSHPULL LOW + +# Control of Spektrum power pin +# no SPEKTRUM_RC pin so this is controlled +# manually +PH2 SPEKTRUM_PWR OUTPUT HIGH GPIO(69) +define HAL_GPIO_SPEKTRUM_PWR 69 +define HAL_SPEKTRUM_PWR_ENABLED 1 + +#Checked in Analogin.cpp -> MAV_POWER_STATUS +PG1 VDD_BRICK_nVALID INPUT +PG2 VDD_BRICK2_nVALID INPUT +PG3 VBUS_nVALID INPUT +PE15 VDD_5V_PERIPH_nOC INPUT +PF13 VDD_5V_HIPOWER_nOC INPUT + +# ID pins +PG0 HW_VER_REV_DRIVE OUTPUT LOW SPEED_VERYLOW +PC4 HW_VER_SENS ADC1 SCALE(1) # ADC1_4 +PC5 HW_REV_SENS ADC1 SCALE(1) # ADC1_8 + +# SPI1 - IMU1(murata),MS5611(BARO),EEPROM +PA5 SPI1_SCK SPI1 SPEED_VERYLOW +PB5 SPI1_MOSI SPI1 SPEED_VERYLOW +PG9 SPI1_MISO SPI1 SPEED_VERYLOW +PH3 SCHA63T_A_CS CS SPEED_VERYLOW # SPI1_CS1 +PH4 SCHA63T_G_CS CS SPEED_VERYLOW # SPI1_CS2 +PH5 MS5611_1_CS CS SPEED_VERYLOW # SPI1_CS3 +PG6 AT25512_CS CS SPEED_VERYLOW # SPI1_CS4 + +# SPI2 + +# SPI3 - FRAM,IMU2(42652) +PB2 SPI3_MOSI SPI3 SPEED_VERYLOW +PC10 SPI3_SCK SPI3 SPEED_VERYLOW +PC11 SPI3_MISO SPI3 SPEED_VERYLOW +PG7 FRAM_CS CS SPEED_VERYLOW # SPI3_CS1 +PF10 IIM42652_CS CS SPEED_VERYLOW # SPI3_CS2 + +# SPI4 - MS5611(BARO),IMU3(42652), +PE12 SPI4_SCK SPI4 SPEED_VERYLOW +PE13 SPI4_MISO SPI4 SPEED_VERYLOW +PE14 SPI4_MOSI SPI4 SPEED_VERYLOW +PH15 MS5611_2_CS CS SPEED_VERYLOW # SPI4_CS1 +PG15 IIM42652_2_CS CS SPEED_VERYLOW # SPI4_CS2 + +# SPI5 - External SPI I/F +#PF7 SPI5_SCK SPI5 SPEED_VERYLOW +#PH7 SPI5_MISO SPI5 SPEED_VERYLOW +#PF11 SPI5_MOSI SPI5 SPEED_VERYLOW +#PE2 SPI5_CS1 CS SPEED_VERYLOW + +# IMU Device Ready Signal Input +PF3 DRDY1_IIM42652_1 INPUT +PF2 DRDY2_IIM42652_1 INPUT +PA15 DRDY1_IIM42652_2 INPUT +PA1 DRDY2_IIM42652_2 INPUT + +PE7 SCHA63T_RESET OUTPUT LOW + +# SPI devices +SPIDEV scha63t_g SPI1 DEVID1 SCHA63T_G_CS MODE0 10*MHZ 10*MHZ +SPIDEV scha63t_a SPI1 DEVID2 SCHA63T_A_CS MODE0 10*MHZ 10*MHZ +SPIDEV ms5611_1 SPI1 DEVID3 MS5611_1_CS MODE3 20*MHZ 20*MHZ +SPIDEV at25512 SPI1 DEVID4 AT25512_CS MODE3 2*MHZ 8*MHZ +SPIDEV ramtron SPI3 DEVID1 FRAM_CS MODE3 8*MHZ 8*MHZ +SPIDEV iim42652_1 SPI3 DEVID2 IIM42652_CS MODE3 2*MHZ 8*MHZ +SPIDEV ms5611_2 SPI4 DEVID1 MS5611_2_CS MODE3 20*MHZ 20*MHZ +SPIDEV iim42652_2 SPI4 DEVID2 IIM42652_2_CS MODE3 2*MHZ 8*MHZ +#define HAL_SPI_CHECK_CLOCK_FREQ + +# JFB110 has 3 IMUs +# IMU devices for JFB110. The JFB110 board has a SCHA63T, two ICM42652, +# the SCHA63T and ICM42652_1 are on the same SPI buses and CS pins. +# The IIM42652_2 is on a different bus +IMU SCHA63T SPI:scha63t_a SPI:scha63t_g ROTATION_NONE +IMU Invensensev3 SPI:iim42652_1 ROTATION_NONE +IMU Invensensev3 SPI:iim42652_2 ROTATION_NONE + +# JFB110 has 2 BAROs +BARO MS56XX SPI:ms5611_1 +BARO MS56XX SPI:ms5611_2 + +define HAL_DEFAULT_INS_FAST_SAMPLE 7 + +# PWM output pins +# we need to disable DMA on the last 2 FMU channels +# as timer 12 doesn't have a TIMn_UP DMA option +PA2 TIM15_CH1 TIM15 PWM(1) GPIO(50) SPEED_VERYLOW +PE6 TIM15_CH2 TIM15 PWM(2) GPIO(51) SPEED_VERYLOW +PA7 TIM3_CH2 TIM3 PWM(3) GPIO(52) SPEED_VERYLOW +PA6 TIM3_CH1 TIM3 PWM(4) GPIO(53) SPEED_VERYLOW +PD15 TIM4_CH4 TIM4 PWM(5) GPIO(54) SPEED_VERYLOW +PE9 TIM1_CH1 TIM1 PWM(6) GPIO(55) SPEED_VERYLOW +PH11 TIM5_CH2 TIM5 PWM(7) GPIO(56) SPEED_VERYLOW +PH10 TIM5_CH1 TIM5 PWM(8) GPIO(57) SPEED_VERYLOW +PA10 TIM1_CH3 TIM1 PWM(9) GPIO(58) SPEED_VERYLOW +PA9 TIM1_CH2 TIM1 PWM(10) GPIO(59) SPEED_VERYLOW +PD14 TIM4_CH3 TIM4 PWM(11) GPIO(60) SPEED_VERYLOW +PD13 TIM4_CH2 TIM4 PWM(12) GPIO(61) SPEED_VERYLOW +PD12 TIM4_CH1 TIM4 PWM(13) GPIO(62) SPEED_VERYLOW +PH9 TIM12_CH2 TIM12 PWM(14) GPIO(63) SPEED_VERYLOW NODMA +PH12 TIM5_CH3 TIM5 PWM(15) GPIO(64) SPEED_VERYLOW +PH6 TIM12_CH1 TIM12 PWM(16) GPIO(65) SPEED_VERYLOW NODMA +PD11 PWM_OE OUTPUT HIGH +PD5 PWM_OE2 OUTPUT HIGH + +# GPIOs +PE11 FMU_CAP1 INPUT GPIO(66) +PB11 FMU_CAP2 INPUT GPIO(67) + +# CAN bus +PD0 CAN1_RX CAN1 SPEED_VERYLOW +PD1 CAN1_TX CAN1 SPEED_VERYLOW +PB12 CAN2_RX CAN2 SPEED_VERYLOW +PB13 CAN2_TX CAN2 SPEED_VERYLOW + +# I2C buses +# I2C1, GPS+MAG +PB8 I2C1_SCL I2C1 +PB9 I2C1_SDA I2C1 + +# I2C2, GPS2+MAG +PF1 I2C2_SCL I2C2 +PF0 I2C2_SDA I2C2 + +# I2C3, IST8310 Internal +PA8 I2C3_SCL I2C3 SPEED_VERYLOW +PH8 I2C3_SDA I2C3 SPEED_VERYLOW + +# I2C4 external +PF14 I2C4_SCL I2C4 +PF15 I2C4_SDA I2C4 + +# order of I2C buses +I2C_ORDER I2C3 I2C1 I2C2 I2C4 +define HAL_I2C_INTERNAL_MASK 1 + +# this board is very tight on DMA channels. To allow for more UART DMA +# we disable DMA on I2C. This also prevents a problem with DMA on I2C +# interfering with IMUs +NODMA I2C* +define STM32_I2C_USE_DMA FALSE + +# builtin compass on JAE JFB110 +define HAL_COMPASS_DISABLE_IST8310_INTERNAL_PROBE +define HAL_PROBE_EXTERNAL_I2C_COMPASSES +COMPASS IST8310 I2C:ALL_INTERNAL:0x0E false ROTATION_YAW_270 +COMPASS IST8310 I2C:ALL_EXTERNAL:0x0E true ROTATION_ROLL_180_YAW_90 + +# armed indication +PB10 nARMED OUTPUT HIGH # TP8 + +# microSD support +PD6 SDMMC2_CK SDMMC2 SPEED_VERYLOW +PD7 SDMMC2_CMD SDMMC2 SPEED_VERYLOW +PB14 SDMMC2_D0 SDMMC2 SPEED_VERYLOW +PB15 SDMMC2_D1 SDMMC2 SPEED_VERYLOW +PG11 SDMMC2_D2 SDMMC2 SPEED_VERYLOW +PB4 SDMMC2_D3 SDMMC2 SPEED_VERYLOW +define FATFS_HAL_DEVICE SDCD2 +PC13 SD_CARD_EN INPUT + +# safety +PD10 LED_SAFETY OUTPUT +PF5 SAFETY_IN INPUT PULLDOWN + +# LEDs +PE3 LED_RED OUTPUT OPENDRAIN GPIO(70) HIGH SPEED_VERYLOW +PE4 LED_GREEN OUTPUT OPENDRAIN GPIO(71) LOW SPEED_VERYLOW +PE5 LED_BLUE OUTPUT OPENDRAIN GPIO(72) HIGH SPEED_VERYLOW + +# setup for "AP_BoardLED" RGB LEDs +define HAL_GPIO_A_LED_PIN 72 +define HAL_GPIO_B_LED_PIN 70 +#define HAL_GPIO_C_LED_PIN 71 +define HAL_GPIO_LED_ON 0 + +# PWM output for buzzer +PF9 TIM14_CH1 TIM14 GPIO(73) ALARM SPEED_VERYLOW + +# RC input (PPM) +PC6 TIM8_CH1 TIM8 RCININT PULLDOWN LOW + +# enable RAMTRON parameter storage +define HAL_STORAGE_SIZE 32768 +define HAL_WITH_RAMTRON 1 + +# allow to have a dedicated safety switch pin +define HAL_HAVE_SAFETY_SWITCH 1 + +DMA_PRIORITY SDMMC* UART* USART* ADC* SPI* TIM* + +# enable FAT filesystem support (needs a microSD defined via SDMMC) +define HAL_OS_FATFS_IO 1 + +# enable DFU reboot for installing bootloader +# note that if firmware is build with --secure-bl then DFU is +# disabled +ENABLE_DFU_BOOT 1 + +# External watchdog gpio +PG5 EXT_WDOG OUTPUT SPEED_VERYLOW +define EXT_WDOG_INTERVAL_MS 50 diff --git a/libraries/AP_HAL_ChibiOS/hwdef/scripts/STM32H755xx.py b/libraries/AP_HAL_ChibiOS/hwdef/scripts/STM32H755xx.py new file mode 100644 index 0000000000..2e29865e1c --- /dev/null +++ b/libraries/AP_HAL_ChibiOS/hwdef/scripts/STM32H755xx.py @@ -0,0 +1,1287 @@ +#!/usr/bin/env python +''' +these tables are generated from the STM32 datasheets for the STM32H755 +''' + +# additional build information for ChibiOS +build = { + "CHIBIOS_STARTUP_MK" : "os/common/startup/ARMCMx/compilers/GCC/mk/startup_stm32h7xx.mk", + "CHIBIOS_PLATFORM_MK" : "os/hal/ports/STM32/STM32H7xx/platform.mk" + } + +# MCU parameters +mcu = { + # location of MCU serial number + 'UDID_START' : 0x1FF1E800, + + # DMA peripheral capabilities: + # - can't use ITCM or DTCM for any DMA + # - SPI1 to SPI5 can use AXI SRAM, SRAM1 to SRAM3 and SRAM4 for DMA + # - SPI6, I2C4 and ADC3 can use SRAM4 on BDMA + # - UARTS can use AXI SRAM, SRAM1 to SRAM3 and SRAM4 for DMA + # - I2C1, I2C2 and I2C3 can use AXI SRAM, SRAM1 to SRAM3 and SRAM4 with DMA + # - timers can use AXI SRAM, SRAM1 to SRAM3 and SRAM4 with DMA + # - ADC12 can use AXI SRAM, SRAM1 to SRAM3 and SRAM4 + # - SDMMC can use AXI SRAM, SRAM1 to SRAM3 with IDMA (cannot use SRAM4) + + # ram map, as list of (address, size-kb, flags) + # flags of 1 means DMA-capable (DMA and BDMA) + # flags of 2 means faster memory for CPU intensive work + # flags of 4 means memory can be used for SDMMC DMA + 'RAM_MAP' : [ + (0x30000000, 256, 0), # SRAM1, SRAM2 + (0x20000000, 128, 2), # DTCM, tightly coupled, no DMA, fast + (0x24000000, 512, 4), # AXI SRAM. Use this for SDMMC IDMA ops + (0x00000400, 63, 2), # ITCM (first 1k removed, to keep address 0 unused) + (0x30040000, 32, 0), # SRAM3. + (0x38000000, 64, 1), # SRAM4. + ], + 'INSTRUCTION_RAM' : (0x00000400, 63), # ITCM (first 1k removed, to keep address 0 unused) + 'FLASH_RAM' : (0x24020000, 384), # AXI SRAM used for process stack and ram functions + 'DATA_RAM' : (0x20010000, 64), # DTCM, tightly coupled, no DMA, fast + + # avoid a problem in the bootloader by making DTCM first. The DCache init + # when using SRAM1 as primary memory gets a hard fault in bootloader + # we can't use DTCM first for main firmware as some builds overflow the first segment + 'RAM_MAP_BOOTLOADER' : [ + (0x20000000, 128, 2), # DTCM, tightly coupled, no DMA, fast + (0x30000000, 256, 0), # SRAM1, SRAM2 + (0x24000000, 512, 4), # AXI SRAM. Use this for SDMMC IDMA ops + (0x00000400, 63, 2), # ITCM (first 1k removed, to keep address 0 unused) + (0x30040000, 32, 0), # SRAM3. + (0x38000000, 64, 1), # SRAM4. + ], + + 'EXPECTED_CLOCK' : 400000000, + + # this MCU has M7 instructions and hardware double precision + 'CORTEX' : 'cortex-m7', + 'CPU_FLAGS' : '-mcpu=cortex-m7 -mfpu=fpv5-d16 -mfloat-abi=hard', + + 'DEFINES' : { + 'HAL_HAVE_HARDWARE_DOUBLE' : '1', + 'HAL_WITH_MCU_MONITORING' : '1', + 'STM32H7' : '1', + } +} + +pincount = { + 'A': 16, + 'B': 16, + 'C': 16, + 'D': 16, + 'E': 16, + 'F': 16, + 'G': 16, + 'H': 16, + 'I': 16, + 'J': 16, + 'K': 16 +} + +# no DMA map as we will dynamically allocate DMA channels using the DMAMUX +DMA_Map = None + +AltFunction_map = { + # format is PIN:FUNCTION : AFNUM + # extracted from tabula-AF-H743.csv + "PA0:ETH_MII_CRS" : 11, + "PA0:EVENT-OUT" : 15, + "PA0:SAI2_SD_B" : 10, + "PA0:SDMMC2_CMD" : 9, + "PA0:TIM15_BKIN" : 4, + "PA0:TIM2_CH1" : 1, + "PA0:TIM2_ETR" : 1, + "PA0:TIM5_CH1" : 2, + "PA0:TIM8_ETR" : 3, + "PA0:UART4_TX" : 8, + "PA0:USART2_CTS" : 7, + "PA1:ETH_MII_RX_CLK" : 11, + "PA1:ETH_RMII_REF_CLK" : 11, + "PA1:EVENT-OUT" : 15, + "PA1:LCD_R2" : 14, + "PA1:LPTIM3_OUT" : 3, + "PA1:QUADSPI_BK1_IO3" : 9, + "PA1:SAI2_MCK_B" : 10, + "PA1:TIM15_CH1N" : 4, + "PA1:TIM2_CH2" : 1, + "PA1:TIM5_CH2" : 2, + "PA1:UART4_RX" : 8, + "PA1:USART2_RTS" : 7, + "PA2:ETH_MDIO" : 11, + "PA2:EVENT-OUT" : 15, + "PA2:LCD_R1" : 14, + "PA2:LPTIM4_OUT" : 3, + "PA2:MDIOS_MDIO" : 12, + "PA2:SAI2_SCK_B" : 8, + "PA2:TIM15_CH1" : 4, + "PA2:TIM2_CH3" : 1, + "PA2:TIM5_CH3" : 2, + "PA2:USART2_TX" : 7, + "PA3:ETH_MII_COL" : 11, + "PA3:EVENT-OUT" : 15, + "PA3:LCD_B2" : 9, + "PA3:LCD_B5" : 14, + "PA3:LPTIM5_OUT" : 3, + "PA3:OTG_HS_ULPI_D0" : 10, + "PA3:TIM15_CH2" : 4, + "PA3:TIM2_CH4" : 1, + "PA3:TIM5_CH4" : 2, + "PA3:USART2_RX" : 7, + "PA4:DCMI_HSYNC" : 13, + "PA4:EVENT-OUT" : 15, + "PA4:I2S1_WS" : 5, + "PA4:I2S3_WS" : 6, + "PA4:LCD_VSYNC" : 14, + "PA4:OTG_HS_SOF" : 12, + "PA4:SPI1_NSS" : 5, + "PA4:SPI3_NSS" : 6, + "PA4:SPI6_NSS" : 8, + "PA4:TIM5_ETR" : 2, + "PA4:USART2_CK" : 7, + "PA5:EVENT-OUT" : 15, + "PA5:I2S1_CK" : 5, + "PA5:LCD_R4" : 14, + "PA5:OTG_HS_ULPI_CK" : 10, + "PA5:SPI1_SCK" : 5, + "PA5:SPI6_SCK" : 8, + "PA5:TIM2_CH1" : 1, + "PA5:TIM2_ETR" : 1, + "PA5:TIM8_CH1N" : 3, + "PA6:DCMI_PIXCLK" : 13, + "PA6:EVENT-OUT" : 15, + "PA6:I2S1_SDI" : 5, + "PA6:LCD_G2" : 14, + "PA6:MDIOS_MDC" : 11, + "PA6:SPI1_MISO" : 5, + "PA6:SPI6_MISO" : 8, + "PA6:TIM13_CH1" : 9, + "PA6:TIM1_BKIN" : 1, + "PA6:TIM1_BKIN_COMP12" : 12, + "PA6:TIM3_CH1" : 2, + "PA6:TIM8_BKIN" : 3, + "PA6:TIM8_BKIN_COMP12" : 10, + "PA7:ETH_MII_RX_DV" : 11, + "PA7:ETH_RMII_CRS_DV" : 11, + "PA7:EVENT-OUT" : 15, + "PA7:FMC_SDNWE" : 12, + "PA7:I2S1_SDO" : 5, + "PA7:SPI1_MOSI" : 5, + "PA7:SPI6_MOSI" : 8, + "PA7:TIM14_CH1" : 9, + "PA7:TIM1_CH1N" : 1, + "PA7:TIM3_CH2" : 2, + "PA7:TIM8_CH1N" : 3, + "PA8:EVENT-OUT" : 15, + "PA8:HRTIM_CHB2" : 2, + "PA8:I2C3_SCL" : 4, + "PA8:LCD_B3" : 13, + "PA8:LCD_R6" : 14, + "PA8:MCO1" : 0, + "PA8:OTG_FS_SOF" : 10, + "PA8:TIM1_CH1" : 1, + "PA8:TIM8_BKIN2" : 3, + "PA8:TIM8_BKIN2_COMP12" : 12, + "PA8:UART7_RX" : 11, + "PA8:USART1_CK" : 7, + "PA9:DCMI_D0" : 13, + "PA9:EVENT-OUT" : 15, + "PA9:CAN1_RX" : 9, + "PA9:HRTIM_CHC1" : 2, + "PA9:I2C3_SMBA" : 4, + "PA9:I2S2_CK" : 5, + "PA9:LCD_R5" : 14, + "PA9:LPUART1_TX" : 3, + "PA9:SPI2_SCK" : 5, + "PA9:TIM1_CH2" : 1, + "PA9:USART1_TX" : 7, + "PA10:DCMI_D1" : 13, + "PA10:EVENT-OUT" : 15, + "PA10:CAN1_TX" : 9, + "PA10:HRTIM_CHC2" : 2, + "PA10:LCD_B1" : 14, + "PA10:LCD_B4" : 12, + "PA10:LPUART1_RX" : 3, + "PA10:MDIOS_MDIO" : 11, + "PA10:OTG_FS_ID" : 10, + "PA10:TIM1_CH3" : 1, + "PA10:USART1_RX" : 7, + "PA11:EVENT-OUT" : 15, + "PA11:CAN1_RX" : 9, + "PA11:HRTIM_CHD1" : 2, + "PA11:I2S2_WS" : 5, + "PA11:LCD_R4" : 14, + "PA11:LPUART1_CTS" : 3, + "PA11:OTG_FS_DM" : 10, + "PA11:SPI2_NSS" : 5, + "PA11:TIM1_CH4" : 1, + "PA11:UART4_RX" : 6, + "PA11:USART1_CTS_NSS" : 7, + "PA12:EVENT-OUT" : 15, + "PA12:CAN1_TX" : 9, + "PA12:HRTIM_CHD2" : 2, + "PA12:I2S2_CK" : 5, + "PA12:LCD_R5" : 14, + "PA12:LPUART1_RTS" : 3, + "PA12:OTG_FS_DP" : 10, + "PA12:SAI2_FS_B" : 8, + "PA12:SPI2_SCK" : 5, + "PA12:TIM1_ETR" : 1, + "PA12:UART4_TX" : 6, + "PA12:USART1_RTS" : 7, + "PA13:EVENT-OUT" : 15, + "PA13:JTMS-SWDIO" : 0, + "PA14:EVENT-OUT" : 15, + "PA14:JTCK-SWCLK" : 0, + "PA15:EVENT-OUT" : 15, + "PA15:HDMI_CEC" : 4, + "PA15:HRTIM_FLT1" : 2, + "PA15:I2S1_WS" : 5, + "PA15:I2S3_WS" : 6, + "PA15:JTDI" : 0, + "PA15:SPI1_NSS" : 5, + "PA15:SPI3_NSS" : 6, + "PA15:SPI6_NSS" : 7, + "PA15:TIM2_CH1" : 1, + "PA15:TIM2_ETR" : 1, + "PA15:UART4_RTS" : 8, + "PA15:UART7_TX" : 11, + "PB0:DFSDM_CKOUT" : 6, + "PB0:ETH_MII_RXD2" : 11, + "PB0:EVENT-OUT" : 15, + "PB0:LCD_G1" : 14, + "PB0:LCD_R3" : 9, + "PB0:OTG_HS_ULPI_D1" : 10, + "PB0:TIM1_CH2N" : 1, + "PB0:TIM3_CH3" : 2, + "PB0:TIM8_CH2N" : 3, + "PB0:UART4_CTS" : 8, + "PB1:DFSDM_DATIN1" : 6, + "PB1:ETH_MII_RXD3" : 11, + "PB1:EVENT-OUT" : 15, + "PB1:LCD_G0" : 14, + "PB1:LCD_R6" : 9, + "PB1:OTG_HS_ULPI_D2" : 10, + "PB1:TIM1_CH3N" : 1, + "PB1:TIM3_CH4" : 2, + "PB1:TIM8_CH3N" : 3, + "PB2:DFSDM_CKIN1" : 4, + "PB2:EVENT-OUT" : 15, + "PB2:I2S3_SDO" : 7, + "PB2:QUADSPI_CLK" : 9, + "PB2:SAI1_D1" : 2, + "PB2:SAI1_SD_A" : 6, + "PB2:SAI4_D1" : 10, + "PB2:SAI4_SD_A" : 8, + "PB2:SPI3_MOSI" : 7, + "PB3:EVENT-OUT" : 15, + "PB3:HRTIM_FLT4" : 2, + "PB3:I2S1_CK" : 5, + "PB3:I2S3_CK" : 6, + "PB3:JTDO" : 0, + "PB3:SDMMC2_D2" : 9, + "PB3:SPI1_SCK" : 5, + "PB3:SPI3_SCK" : 6, + "PB3:SPI6_SCK" : 8, + "PB3:TIM2_CH2" : 1, + "PB3:TRACESWO" : 0, + "PB3:UART7_RX" : 11, + "PB4:EVENT-OUT" : 15, + "PB4:HRTIM_EEV6" : 3, + "PB4:I2S1_SDI" : 5, + "PB4:I2S2_WS" : 7, + "PB4:I2S3_SDI" : 6, + "PB4:NJTRST" : 0, + "PB4:SDMMC2_D3" : 9, + "PB4:SPI1_MISO" : 5, + "PB4:SPI2_NSS" : 7, + "PB4:SPI3_MISO" : 6, + "PB4:SPI6_MISO" : 8, + "PB4:TIM16_BKIN" : 1, + "PB4:TIM3_CH1" : 2, + "PB4:UART7_TX" : 11, + "PB5:DCMI_D10" : 13, + "PB5:ETH_PPS_OUT" : 11, + "PB5:EVENT-OUT" : 15, + "PB5:CAN2_RX" : 9, + "PB5:FMC_SDCKE1" : 12, + "PB5:HRTIM_EEV7" : 3, + "PB5:I2C1_SMBA" : 4, + "PB5:I2C4_SMBA" : 6, + "PB5:I2S1_SDO" : 5, + "PB5:I2S3_SDO" : 7, + "PB5:OTG_HS_ULPI_D7" : 10, + "PB5:SPI1_MOSI" : 5, + "PB5:SPI3_MOSI" : 7, + "PB5:SPI6_MOSI" : 8, + "PB5:TIM17_BKIN" : 1, + "PB5:TIM3_CH2" : 2, + "PB5:UART5_RX" : 14, + "PB6:DCMI_D5" : 13, + "PB6:DFSDM_DATIN5" : 11, + "PB6:EVENT-OUT" : 15, + "PB6:CAN2_TX" : 9, + "PB6:FMC_SDNE1" : 12, + "PB6:HDMI_CEC" : 5, + "PB6:HRTIM_EEV8" : 3, + "PB6:I2C1_SCL" : 4, + "PB6:I2C4_SCL" : 6, + "PB6:LPUART1_TX" : 8, + "PB6:QUADSPI_BK1_NCS" : 10, + "PB6:TIM16_CH1N" : 1, + "PB6:TIM4_CH1" : 2, + "PB6:UART5_TX" : 14, + "PB6:USART1_TX" : 7, + "PB7:DCMI_VSYNC" : 13, + "PB7:DFSDM_CKIN5" : 11, + "PB7:EVENT-OUT" : 15, + "PB7:CAN2_TX" : 9, + "PB7:FMC_NL" : 12, + "PB7:HRTIM_EEV9" : 3, + "PB7:I2C1_SDA" : 4, + "PB7:I2C4_SDA" : 6, + "PB7:LPUART1_RX" : 8, + "PB7:TIM17_CH1N" : 1, + "PB7:TIM4_CH2" : 2, + "PB7:USART1_RX" : 7, + "PB8:DCMI_D6" : 13, + "PB8:DFSDM_CKIN7" : 3, + "PB8:ETH_MII_TXD3" : 11, + "PB8:EVENT-OUT" : 15, + "PB8:CAN1_RX" : 9, + "PB8:I2C1_SCL" : 4, + "PB8:I2C4_SCL" : 6, + "PB8:LCD_B6" : 14, + "PB8:SDMMC1_CKIN" : 7, + "PB8:SDMMC1_D4" : 12, + "PB8:SDMMC2_D4" : 10, + "PB8:TIM16_CH1" : 1, + "PB8:TIM4_CH3" : 2, + "PB8:UART4_RX" : 8, + "PB9:DCMI_D7" : 13, + "PB9:DFSDM_DATIN7" : 3, + "PB9:EVENT-OUT" : 15, + "PB9:CAN1_TX" : 9, + "PB9:I2C1_SDA" : 4, + "PB9:I2C4_SDA" : 6, + "PB9:I2C4_SMBA" : 11, + "PB9:I2S2_WS" : 5, + "PB9:LCD_B7" : 14, + "PB9:SDMMC1_CDIR" : 7, + "PB9:SDMMC1_D5" : 12, + "PB9:SDMMC2_D5" : 10, + "PB9:SPI2_NSS" : 5, + "PB9:TIM17_CH1" : 1, + "PB9:TIM4_CH4" : 2, + "PB9:UART4_TX" : 8, + "PB10:DFSDM_DATIN7" : 6, + "PB10:ETH_MII_RX_ER" : 11, + "PB10:EVENT-OUT" : 15, + "PB10:HRTIM_SCOUT" : 2, + "PB10:I2C2_SCL" : 4, + "PB10:I2S2_CK" : 5, + "PB10:LCD_G4" : 14, + "PB10:LPTIM2_IN1" : 3, + "PB10:OTG_HS_ULPI_D3" : 10, + "PB10:QUADSPI_BK1_NCS" : 9, + "PB10:SPI2_SCK" : 5, + "PB10:TIM2_CH3" : 1, + "PB10:USART3_TX" : 7, + "PB11:DFSDM_CKIN7" : 6, + "PB11:ETH_MII_TX_EN" : 11, + "PB11:ETH_RMII_TX_EN" : 11, + "PB11:EVENT-OUT" : 15, + "PB11:HRTIM_SCIN" : 2, + "PB11:I2C2_SDA" : 4, + "PB11:LCD_G5" : 14, + "PB11:LPTIM2_ETR" : 3, + "PB11:OTG_HS_ULPI_D4" : 10, + "PB11:TIM2_CH4" : 1, + "PB11:USART3_RX" : 7, + "PB12:DFSDM_DATIN1" : 6, + "PB12:ETH_MII_TXD0" : 11, + "PB12:ETH_RMII_TXD0" : 11, + "PB12:EVENT-OUT" : 15, + "PB12:CAN2_RX" : 9, + "PB12:I2C2_SMBA" : 4, + "PB12:I2S2_WS" : 5, + "PB12:OTG_HS_ID" : 12, + "PB12:OTG_HS_ULPI_D5" : 10, + "PB12:SPI2_NSS" : 5, + "PB12:TIM1_BKIN" : 1, + "PB12:TIM1_BKIN_COMP12" : 13, + "PB12:UART5_RX" : 14, + "PB12:USART3_CK" : 7, + "PB13:DFSDM_CKIN1" : 6, + "PB13:ETH_MII_TXD1" : 11, + "PB13:ETH_RMII_TXD1" : 11, + "PB13:EVENT-OUT" : 15, + "PB13:CAN2_TX" : 9, + "PB13:I2S2_CK" : 5, + "PB13:LPTIM2_OUT" : 3, + "PB13:OTG_HS_ULPI_D6" : 10, + "PB13:SPI2_SCK" : 5, + "PB13:TIM1_CH1N" : 1, + "PB13:UART5_TX" : 14, + "PB13:USART3_CTS_NSS" : 7, + "PB14:DFSDM_DATIN2" : 6, + "PB14:EVENT-OUT" : 15, + "PB14:I2S2_SDI" : 5, + "PB14:OTG_HS_DM" : 12, + "PB14:SDMMC2_D0" : 9, + "PB14:SPI2_MISO" : 5, + "PB14:TIM12_CH1" : 2, + "PB14:TIM1_CH2N" : 1, + "PB14:TIM8_CH2N" : 3, + "PB14:UART4_RTS" : 8, + "PB14:USART1_TX" : 4, + "PB14:USART3_RTS" : 7, + "PB15:DFSDM_CKIN2" : 6, + "PB15:EVENT-OUT" : 15, + "PB15:I2S2_SDO" : 5, + "PB15:OTG_HS_DP" : 12, + "PB15:RTC_REFIN" : 0, + "PB15:SDMMC2_D1" : 9, + "PB15:SPI2_MOSI" : 5, + "PB15:TIM12_CH2" : 2, + "PB15:TIM1_CH3N" : 1, + "PB15:TIM8_CH3N" : 3, + "PB15:UART4_CTS" : 8, + "PB15:USART1_RX" : 4, + "PC0:DFSDM_CKIN0" : 3, + "PC0:DFSDM_DATIN4" : 6, + "PC0:EVENT-OUT" : 15, + "PC0:FMC_SDNWE" : 12, + "PC0:LCD_R5" : 14, + "PC0:OTG_HS_ULPI_STP" : 10, + "PC0:SAI2_FS_B" : 8, + "PC1:DFSDM_CKIN4" : 4, + "PC1:DFSDM_DATIN0" : 3, + "PC1:ETH_MDC" : 11, + "PC1:EVENT-OUT" : 15, + "PC1:I2S2_SDO" : 5, + "PC1:MDIOS_MDC" : 12, + "PC1:SAI1_D1" : 2, + "PC1:SAI1_SD_A" : 6, + "PC1:SAI4_D1" : 10, + "PC1:SAI4_SD_A" : 8, + "PC1:SDMMC2_CK" : 9, + "PC1:SPI2_MOSI" : 5, + "PC1:TRACED0" : 0, + "PC2:DFSDM_CKIN1" : 3, + "PC2:DFSDM_CKOUT" : 6, + "PC2:ETH_MII_TXD2" : 11, + "PC2:EVENT-OUT" : 15, + "PC2:FMC_SDNE0" : 12, + "PC2:I2S2_SDI" : 5, + "PC2:OTG_HS_ULPI_DIR" : 10, + "PC2:SPI2_MISO" : 5, + "PC3:DFSDM_DATIN1" : 3, + "PC3:ETH_MII_TX_CLK" : 11, + "PC3:EVENT-OUT" : 15, + "PC3:FMC_SDCKE0" : 12, + "PC3:I2S2_SDO" : 5, + "PC3:OTG_HS_ULPI_NXT" : 10, + "PC3:SPI2_MOSI" : 5, + "PC4:DFSDM_CKIN2" : 3, + "PC4:ETH_MII_RXD0" : 11, + "PC4:ETH_RMII_RXD0" : 11, + "PC4:EVENT-OUT" : 15, + "PC4:FMC_SDNE0" : 12, + "PC4:I2S1_MCK" : 5, + "PC4:SPDIFRX_IN2" : 9, + "PC5:COMP_1_OUT" : 13, + "PC5:DFSDM_DATIN2" : 3, + "PC5:ETH_MII_RXD1" : 11, + "PC5:ETH_RMII_RXD1" : 11, + "PC5:EVENT-OUT" : 15, + "PC5:FMC_SDCKE0" : 12, + "PC5:SAI1_D3" : 2, + "PC5:SAI4_D3" : 10, + "PC5:SPDIFRX_IN3" : 9, + "PC6:DCMI_D0" : 13, + "PC6:DFSDM_CKIN3" : 4, + "PC6:EVENT-OUT" : 15, + "PC6:FMC_NWAIT" : 9, + "PC6:HRTIM_CHA1" : 1, + "PC6:I2S2_MCK" : 5, + "PC6:LCD_HSYNC" : 14, + "PC6:SDMMC1_D0DIR" : 8, + "PC6:SDMMC1_D6" : 12, + "PC6:SDMMC2_D6" : 10, + "PC6:TIM3_CH1" : 2, + "PC6:TIM8_CH1" : 3, + "PC6:USART6_TX" : 7, + "PC7:DCMI_D1" : 13, + "PC7:DFSDM_DATIN3" : 4, + "PC7:EVENT-OUT" : 15, + "PC7:FMC_NE1" : 9, + "PC7:HRTIM_CHA2" : 1, + "PC7:I2S3_MCK" : 6, + "PC7:LCD_G6" : 14, + "PC7:SDMMC1_D123DIR" : 8, + "PC7:SDMMC1_D7" : 12, + "PC7:SDMMC2_D7" : 10, + "PC7:SWPMI_TX" : 11, + "PC7:TIM3_CH2" : 2, + "PC7:TIM8_CH2" : 3, + "PC7:TRGIO" : 0, + "PC7:USART6_RX" : 7, + "PC8:DCMI_D2" : 13, + "PC8:EVENT-OUT" : 15, + "PC8:FMC_NCE" : 9, + "PC8:FMC_NE2" : 9, + "PC8:HRTIM_CHB1" : 1, + "PC8:SDMMC1_D0" : 12, + "PC8:SWPMI_RX" : 11, + "PC8:TIM3_CH3" : 2, + "PC8:TIM8_CH3" : 3, + "PC8:TRACED1" : 0, + "PC8:UART5_RTS" : 8, + "PC8:USART6_CK" : 7, + "PC9:DCMI_D3" : 13, + "PC9:EVENT-OUT" : 15, + "PC9:I2C3_SDA" : 4, + "PC9:I2S_CKIN" : 5, + "PC9:LCD_B2" : 14, + "PC9:LCD_G3" : 10, + "PC9:MCO2" : 0, + "PC9:QUADSPI_BK1_IO0" : 9, + "PC9:SDMMC1_D1" : 12, + "PC9:SWPMI_SUSPEND" : 11, + "PC9:TIM3_CH4" : 2, + "PC9:TIM8_CH4" : 3, + "PC9:UART5_CTS" : 8, + "PC10:DCMI_D8" : 13, + "PC10:DFSDM_CKIN5" : 3, + "PC10:EVENT-OUT" : 15, + "PC10:HRTIM_EEV1" : 2, + "PC10:I2S3_CK" : 6, + "PC10:LCD_R2" : 14, + "PC10:QUADSPI_BK1_IO1" : 9, + "PC10:SDMMC1_D2" : 12, + "PC10:SPI3_SCK" : 6, + "PC10:UART4_TX" : 8, + "PC10:USART3_TX" : 7, + "PC11:DCMI_D4" : 13, + "PC11:DFSDM_DATIN5" : 3, + "PC11:EVENT-OUT" : 15, + "PC11:HRTIM_FLT2" : 2, + "PC11:I2S3_SDI" : 6, + "PC11:QUADSPI_BK2_NCS" : 9, + "PC11:SDMMC1_D3" : 12, + "PC11:SPI3_MISO" : 6, + "PC11:UART4_RX" : 8, + "PC11:USART3_RX" : 7, + "PC12:DCMI_D9" : 13, + "PC12:EVENT-OUT" : 15, + "PC12:HRTIM_EEV2" : 2, + "PC12:I2S3_SDO" : 6, + "PC12:SDMMC1_CK" : 12, + "PC12:SPI3_MOSI" : 6, + "PC12:TRACED3" : 0, + "PC12:UART5_TX" : 8, + "PC12:USART3_CK" : 7, + "PC13:EVENT-OUT" : 15, + "PC14:EVENT-OUT" : 15, + "PC15:EVENT-OUT" : 15, + "PD0:DFSDM_CKIN6" : 3, + "PD0:EVENT-OUT" : 15, + "PD0:CAN1_RX" : 9, + "PD0:FMC_D2" : 12, + "PD0:FMC_DA2" : 12, + "PD0:SAI3_SCK_A" : 6, + "PD0:UART4_RX" : 8, + "PD1:DFSDM_DATIN6" : 3, + "PD1:EVENT-OUT" : 15, + "PD1:CAN1_TX" : 9, + "PD1:FMC_D3" : 12, + "PD1:FMC_DA3" : 12, + "PD1:SAI3_SD_A" : 6, + "PD1:UART4_TX" : 8, + "PD2:DCMI_D11" : 13, + "PD2:EVENT-OUT" : 15, + "PD2:SDMMC1_CMD" : 12, + "PD2:TIM3_ETR" : 2, + "PD2:TRACED2" : 0, + "PD2:UART5_RX" : 8, + "PD3:DCMI_D5" : 13, + "PD3:DFSDM_CKOUT" : 3, + "PD3:EVENT-OUT" : 15, + "PD3:FMC_CLK" : 12, + "PD3:I2S2_CK" : 5, + "PD3:LCD_G7" : 14, + "PD3:SPI2_SCK" : 5, + "PD3:USART2_CTS" : 7, + "PD4:EVENT-OUT" : 15, + "PD4:CAN1_RX" : 9, + "PD4:FMC_NOE" : 12, + "PD4:HRTIM_FLT3" : 2, + "PD4:SAI3_FS_A" : 6, + "PD4:USART2_RTS" : 7, + "PD5:EVENT-OUT" : 15, + "PD5:CAN1_TX" : 9, + "PD5:FMC_NWE" : 12, + "PD5:HRTIM_EEV3" : 2, + "PD5:USART2_TX" : 7, + "PD6:DCMI_D10" : 13, + "PD6:DFSDM_CKIN4" : 3, + "PD6:DFSDM_DATIN1" : 4, + "PD6:EVENT-OUT" : 15, + "PD6:CAN2_RX" : 9, + "PD6:FMC_NWAIT" : 12, + "PD6:I2S3_SDO" : 5, + "PD6:LCD_B2" : 14, + "PD6:SAI1_D1" : 2, + "PD6:SAI1_SD_A" : 6, + "PD6:SAI4_D1" : 10, + "PD6:SAI4_SD_A" : 8, + "PD6:SDMMC2_CK" : 11, + "PD6:SPI3_MOSI" : 5, + "PD6:USART2_RX" : 7, + "PD7:DFSDM_CKIN1" : 6, + "PD7:DFSDM_DATIN4" : 3, + "PD7:EVENT-OUT" : 15, + "PD7:FMC_NE1" : 12, + "PD7:I2S1_SDO" : 5, + "PD7:SDMMC2_CMD" : 11, + "PD7:SPDIFRX_IN0" : 9, + "PD7:SPI1_MOSI" : 5, + "PD7:USART2_CK" : 7, + "PD8:DFSDM_CKIN3" : 3, + "PD8:EVENT-OUT" : 15, + "PD8:FMC_D13" : 12, + "PD8:FMC_DA13" : 12, + "PD8:SAI3_SCK_B" : 6, + "PD8:SPDIFRX_IN1" : 9, + "PD8:USART3_TX" : 7, + "PD9:DFSDM_DATIN3" : 3, + "PD9:EVENT-OUT" : 15, + "PD9:CAN2_RX" : 9, + "PD9:FMC_D14" : 12, + "PD9:FMC_DA14" : 12, + "PD9:SAI3_SD_B" : 6, + "PD9:USART3_RX" : 7, + "PD10:DFSDM_CKOUT" : 3, + "PD10:EVENT-OUT" : 15, + "PD10:CAN2_TX" : 9, + "PD10:FMC_D15" : 12, + "PD10:FMC_DA15" : 12, + "PD10:LCD_B3" : 14, + "PD10:SAI3_FS_B" : 6, + "PD10:USART3_CK" : 7, + "PD11:EVENT-OUT" : 15, + "PD11:FMC_A16" : 12, + "PD11:I2C4_SMBA" : 4, + "PD11:LPTIM2_IN2" : 3, + "PD11:QUADSPI_BK1_IO0" : 9, + "PD11:SAI2_SD_A" : 10, + "PD11:USART3_CTS" : 7, + "PD12:EVENT-OUT" : 15, + "PD12:FMC_A17" : 12, + "PD12:I2C4_SCL" : 4, + "PD12:LPTIM1_IN1" : 1, + "PD12:LPTIM2_IN1" : 3, + "PD12:QUADSPI_BK1_IO1" : 9, + "PD12:SAI2_FS_A" : 10, + "PD12:TIM4_CH1" : 2, + "PD12:USART3_RTS" : 7, + "PD13:EVENT-OUT" : 15, + "PD13:FMC_A18" : 12, + "PD13:I2C4_SDA" : 4, + "PD13:LPTIM1_OUT" : 1, + "PD13:QUADSPI_BK1_IO3" : 9, + "PD13:SAI2_SCK_A" : 10, + "PD13:TIM4_CH2" : 2, + "PD14:EVENT-OUT" : 15, + "PD14:FMC_D0" : 12, + "PD14:FMC_DA0" : 12, + "PD14:SAI3_MCLK_B" : 6, + "PD14:TIM4_CH3" : 2, + "PD14:UART8_CTS" : 8, + "PD15:EVENT-OUT" : 15, + "PD15:FMC_D1" : 12, + "PD15:FMC_DA1" : 12, + "PD15:SAI3_MCLK_A" : 6, + "PD15:TIM4_CH4" : 2, + "PD15:UART8_RTS" : 8, + "PE0:DCMI_D2" : 13, + "PE0:EVENT-OUT" : 15, + "PE0:CAN1_RX" : 9, + "PE0:FMC_NBL0" : 12, + "PE0:HRTIM_SCIN" : 3, + "PE0:LPTIM1_ETR" : 1, + "PE0:LPTIM2_ETR" : 4, + "PE0:SAI2_MCK_A" : 10, + "PE0:TIM4_ETR" : 2, + "PE0:UART8_RX" : 8, + "PE1:DCMI_D3" : 13, + "PE1:EVENT-OUT" : 15, + "PE1:CAN1_TX" : 9, + "PE1:FMC_NBL1" : 12, + "PE1:HRTIM_SCOUT" : 3, + "PE1:LPTIM1_IN2" : 1, + "PE1:UART8_TX" : 8, + "PE2:ETH_MII_TXD3" : 11, + "PE2:EVENT-OUT" : 15, + "PE2:FMC_A23" : 12, + "PE2:QUADSPI_BK1_IO2" : 9, + "PE2:SAI1_CK1" : 2, + "PE2:SAI1_MCLK_A" : 6, + "PE2:SAI4_CK1" : 10, + "PE2:SAI4_MCLK_A" : 8, + "PE2:SPI4_SCK" : 5, + "PE2:TRACECLK" : 0, + "PE3:EVENT-OUT" : 15, + "PE3:FMC_A19" : 12, + "PE3:SAI1_SD_B" : 6, + "PE3:SAI4_SD_B" : 8, + "PE3:TIM15_BKIN" : 4, + "PE3:TRACED0" : 0, + "PE4:DCMI_D4" : 13, + "PE4:DFSDM_DATIN3" : 3, + "PE4:EVENT-OUT" : 15, + "PE4:FMC_A20" : 12, + "PE4:LCD_B0" : 14, + "PE4:SAI1_D2" : 2, + "PE4:SAI1_FS_A" : 6, + "PE4:SAI4_D2" : 10, + "PE4:SAI4_FS_A" : 8, + "PE4:SPI4_NSS" : 5, + "PE4:TIM15_CH1N" : 4, + "PE4:TRACED1" : 0, + "PE5:DCMI_D6" : 13, + "PE5:DFSDM_CKIN3" : 3, + "PE5:EVENT-OUT" : 15, + "PE5:FMC_A21" : 12, + "PE5:LCD_G0" : 14, + "PE5:SAI1_CK2" : 2, + "PE5:SAI1_SCK_A" : 6, + "PE5:SAI4_CK2" : 10, + "PE5:SAI4_SCK_A" : 8, + "PE5:SPI4_MISO" : 5, + "PE5:TIM15_CH1" : 4, + "PE5:TRACED2" : 0, + "PE6:DCMI_D7" : 13, + "PE6:EVENT-OUT" : 15, + "PE6:FMC_A22" : 12, + "PE6:LCD_G1" : 14, + "PE6:SAI1_D1" : 2, + "PE6:SAI1_SD_A" : 6, + "PE6:SAI2_MCK_B" : 10, + "PE6:SAI4_D1" : 9, + "PE6:SAI4_SD_A" : 8, + "PE6:SPI4_MOSI" : 5, + "PE6:TIM15_CH2" : 4, + "PE6:TIM1_BKIN2" : 1, + "PE6:TIM1_BKIN2_COMP12" : 11, + "PE6:TRACED3" : 0, + "PE7:DFSDM_DATIN2" : 3, + "PE7:EVENT-OUT" : 15, + "PE7:FMC_D4" : 12, + "PE7:FMC_DA4" : 12, + "PE7:QUADSPI_BK2_IO0" : 10, + "PE7:TIM1_ETR" : 1, + "PE7:UART7_RX" : 7, + "PE8:COMP_2_OUT" : 13, + "PE8:DFSDM_CKIN2" : 3, + "PE8:EVENT-OUT" : 15, + "PE8:FMC_D5" : 12, + "PE8:FMC_DA5" : 12, + "PE8:QUADSPI_BK2_IO1" : 10, + "PE8:TIM1_CH1N" : 1, + "PE8:UART7_TX" : 7, + "PE9:DFSDM_CKOUT" : 3, + "PE9:EVENT-OUT" : 15, + "PE9:FMC_D6" : 12, + "PE9:FMC_DA6" : 12, + "PE9:QUADSPI_BK2_IO2" : 10, + "PE9:TIM1_CH1" : 1, + "PE9:UART7_RTS" : 7, + "PE10:DFSDM_DATIN4" : 3, + "PE10:EVENT-OUT" : 15, + "PE10:FMC_D7" : 12, + "PE10:FMC_DA7" : 12, + "PE10:QUADSPI_BK2_IO3" : 10, + "PE10:TIM1_CH2N" : 1, + "PE10:UART7_CTS" : 7, + "PE11:DFSDM_CKIN4" : 3, + "PE11:EVENT-OUT" : 15, + "PE11:FMC_D8" : 12, + "PE11:FMC_DA8" : 12, + "PE11:LCD_G3" : 14, + "PE11:SAI2_SD_B" : 10, + "PE11:SPI4_NSS" : 5, + "PE11:TIM1_CH2" : 1, + "PE12:COMP_1_OUT" : 13, + "PE12:DFSDM_DATIN5" : 3, + "PE12:EVENT-OUT" : 15, + "PE12:FMC_D9" : 12, + "PE12:FMC_DA9" : 12, + "PE12:LCD_B4" : 14, + "PE12:SAI2_SCK_B" : 10, + "PE12:SPI4_SCK" : 5, + "PE12:TIM1_CH3N" : 1, + "PE13:COMP_2_OUT" : 13, + "PE13:DFSDM_CKIN5" : 3, + "PE13:EVENT-OUT" : 15, + "PE13:FMC_D10" : 12, + "PE13:FMC_DA10" : 12, + "PE13:LCD_DE" : 14, + "PE13:SAI2_FS_B" : 10, + "PE13:SPI4_MISO" : 5, + "PE13:TIM1_CH3" : 1, + "PE14:EVENT-OUT" : 15, + "PE14:FMC_D11" : 12, + "PE14:FMC_DA11" : 12, + "PE14:LCD_CLK" : 14, + "PE14:SAI2_MCK_B" : 10, + "PE14:SPI4_MOSI" : 5, + "PE14:TIM1_CH4" : 1, + "PE15:EVENT-OUT" : 15, + "PE15:FMC_D12" : 12, + "PE15:FMC_DA12" : 12, + "PE15:HDMI__TIM1_BKIN" : 5, + "PE15:LCD_R7" : 14, + "PE15:TIM1_BKIN" : 1, + "PE15:TIM1_BKIN_COMP12" : 13, + "PF0:EVENT-OUT" : 15, + "PF0:FMC_A0" : 12, + "PF0:I2C2_SDA" : 4, + "PF1:EVENT-OUT" : 15, + "PF1:FMC_A1" : 12, + "PF1:I2C2_SCL" : 4, + "PF2:EVENT-OUT" : 15, + "PF2:FMC_A2" : 12, + "PF2:I2C2_SMBA" : 4, + "PF3:EVENT-OUT" : 15, + "PF3:FMC_A3" : 12, + "PF4:EVENT-OUT" : 15, + "PF4:FMC_A4" : 12, + "PF5:EVENT-OUT" : 15, + "PF5:FMC_A5" : 12, + "PF6:EVENT-OUT" : 15, + "PF6:QUADSPI_BK1_IO3" : 9, + "PF6:SAI1_SD_B" : 6, + "PF6:SAI4_SD_B" : 8, + "PF6:SPI5_NSS" : 5, + "PF6:TIM16_CH1" : 1, + "PF6:UART7_RX" : 7, + "PF7:EVENT-OUT" : 15, + "PF7:QUADSPI_BK1_IO2" : 9, + "PF7:SAI1_MCLK_B" : 6, + "PF7:SAI4_MCLK_B" : 8, + "PF7:SPI5_SCK" : 5, + "PF7:TIM17_CH1" : 1, + "PF7:UART7_TX" : 7, + "PF8:EVENT-OUT" : 15, + "PF8:QUADSPI_BK1_IO0" : 10, + "PF8:SAI1_SCK_B" : 6, + "PF8:SAI4_SCK_B" : 8, + "PF8:SPI5_MISO" : 5, + "PF8:TIM13_CH1" : 9, + "PF8:TIM16_CH1N" : 1, + "PF8:UART7_RTS" : 7, + "PF9:EVENT-OUT" : 15, + "PF9:QUADSPI_BK1_IO1" : 10, + "PF9:SAI1_FS_B" : 6, + "PF9:SAI4_FS_B" : 8, + "PF9:SPI5_MOSI" : 5, + "PF9:TIM14_CH1" : 9, + "PF9:TIM17_CH1N" : 1, + "PF9:UART7_CTS" : 7, + "PF10:DCMI_D11" : 13, + "PF10:EVENT-OUT" : 15, + "PF10:LCD_DE" : 14, + "PF10:QUADSPI_CLK" : 9, + "PF10:SAI1_D3" : 2, + "PF10:SAI4_D3" : 10, + "PF10:TIM16_BKIN" : 1, + "PF11:DCMI_D12" : 13, + "PF11:EVENT-OUT" : 15, + "PF11:FMC_SDNRAS" : 12, + "PF11:SAI2_SD_B" : 10, + "PF11:SPI5_MOSI" : 5, + "PF12:EVENT-OUT" : 15, + "PF12:FMC_A6" : 12, + "PF13:DFSDM_DATIN6" : 3, + "PF13:EVENT-OUT" : 15, + "PF13:FMC_A7" : 12, + "PF13:I2C4_SMBA" : 4, + "PF14:DFSDM_CKIN6" : 3, + "PF14:EVENT-OUT" : 15, + "PF14:FMC_A8" : 12, + "PF14:I2C4_SCL" : 4, + "PF15:EVENT-OUT" : 15, + "PF15:FMC_A9" : 12, + "PF15:I2C4_SDA" : 4, + "PG0:EVENT-OUT" : 15, + "PG0:FMC_A10" : 12, + "PG1:EVENT-OUT" : 15, + "PG1:FMC_A11" : 12, + "PG2:EVENT-OUT" : 15, + "PG2:FMC_A12" : 12, + "PG2:TIM8_BKIN" : 3, + "PG2:TIM8_BKIN_COMP12" : 11, + "PG3:EVENT-OUT" : 15, + "PG3:FMC_A13" : 12, + "PG3:TIM8_BKIN2" : 3, + "PG3:TIM8_BKIN2_COMP12" : 11, + "PG4:EVENT-OUT" : 15, + "PG4:FMC_A14" : 12, + "PG4:FMC_BA0" : 12, + "PG4:TIM1_BKIN2" : 1, + "PG4:TIM1_BKIN2_COMP12" : 11, + "PG5:EVENT-OUT" : 15, + "PG5:FMC_A15" : 12, + "PG5:FMC_BA1" : 12, + "PG5:TIM1_ETR" : 1, + "PG6:DCMI_D12" : 13, + "PG6:EVENT-OUT" : 15, + "PG6:FMC_NE3" : 12, + "PG6:HRTIM_CHE1" : 2, + "PG6:LCD_R7" : 14, + "PG6:QUADSPI_BK1_NCS" : 10, + "PG6:TIM17_BKIN" : 1, + "PG7:DCMI_D13" : 13, + "PG7:EVENT-OUT" : 15, + "PG7:FMC_INT" : 12, + "PG7:HRTIM_CHE2" : 2, + "PG7:LCD_CLK" : 14, + "PG7:SAI1_MCLK_A" : 6, + "PG7:USART6_CK" : 7, + "PG8:ETH_PPS_OUT" : 11, + "PG8:EVENT-OUT" : 15, + "PG8:FMC_SDCLK" : 12, + "PG8:LCD_G7" : 14, + "PG8:SPDIFRX_IN2" : 8, + "PG8:SPI6_NSS" : 5, + "PG8:TIM8_ETR" : 3, + "PG8:USART6_RTS" : 7, + "PG9:DCMI_VSYNC" : 13, + "PG9:EVENT-OUT" : 15, + "PG9:FMC_NCE" : 12, + "PG9:FMC_NE2" : 12, + "PG9:I2S1_SDI" : 5, + "PG9:QUADSPI_BK2_IO2" : 9, + "PG9:SAI2_FS_B" : 10, + "PG9:SPDIFRX_IN3" : 8, + "PG9:SPI1_MISO" : 5, + "PG9:USART6_RX" : 7, + "PG10:DCMI_D2" : 13, + "PG10:EVENT-OUT" : 15, + "PG10:FMC_NE3" : 12, + "PG10:HRTIM_FLT5" : 2, + "PG10:I2S1_WS" : 5, + "PG10:LCD_B2" : 14, + "PG10:LCD_G3" : 9, + "PG10:SAI2_SD_B" : 10, + "PG10:SPI1_NSS" : 5, + "PG11:DCMI_D3" : 13, + "PG11:ETH_MII_TX_EN" : 11, + "PG11:ETH_RMII_TX_EN" : 11, + "PG11:EVENT-OUT" : 15, + "PG11:HRTIM_EEV4" : 2, + "PG11:I2S1_CK" : 5, + "PG11:LCD_B3" : 14, + "PG11:SDMMC2_D2" : 10, + "PG11:SPDIFRX_IN0" : 8, + "PG11:SPI1_SCK" : 5, + "PG12:ETH_MII_TXD1" : 11, + "PG12:ETH_RMII_TXD1" : 11, + "PG12:EVENT-OUT" : 15, + "PG12:FMC_NE4" : 12, + "PG12:HRTIM_EEV5" : 2, + "PG12:LCD_B1" : 14, + "PG12:LCD_B4" : 9, + "PG12:LPTIM1_IN1" : 1, + "PG12:SPDIFRX_IN1" : 8, + "PG12:SPI6_MISO" : 5, + "PG12:USART6_RTS" : 7, + "PG13:ETH_MII_TXD0" : 11, + "PG13:ETH_RMII_TXD0" : 11, + "PG13:EVENT-OUT" : 15, + "PG13:FMC_A24" : 12, + "PG13:HRTIM_EEV10" : 2, + "PG13:LCD_R0" : 14, + "PG13:LPTIM1_OUT" : 1, + "PG13:SPI6_SCK" : 5, + "PG13:TRACED0" : 0, + "PG13:USART6_CTS" : 7, + "PG14:ETH_MII_TXD1" : 11, + "PG14:ETH_RMII_TXD1" : 11, + "PG14:EVENT-OUT" : 15, + "PG14:FMC_A25" : 12, + "PG14:LCD_B0" : 14, + "PG14:LPTIM1_ETR" : 1, + "PG14:QUADSPI_BK2_IO3" : 9, + "PG14:SPI6_MOSI" : 5, + "PG14:TRACED1" : 0, + "PG14:USART6_TX" : 7, + "PG15:DCMI_D13" : 13, + "PG15:EVENT-OUT" : 15, + "PG15:FMC_SDNCAS" : 12, + "PG15:USART6_CTS" : 7, + "PH0:EVENT-OUT" : 15, + "PH1:EVENT-OUT" : 15, + "PH2:ETH_MII_CRS" : 11, + "PH2:EVENT-OUT" : 15, + "PH2:FMC_SDCKE0" : 12, + "PH2:LCD_R0" : 14, + "PH2:LPTIM1_IN2" : 1, + "PH2:QUADSPI_BK2_IO0" : 9, + "PH2:SAI2_SCK_B" : 10, + "PH3:ETH_MII_COL" : 11, + "PH3:EVENT-OUT" : 15, + "PH3:FMC_SDNE0" : 12, + "PH3:LCD_R1" : 14, + "PH3:QUADSPI_BK2_IO1" : 9, + "PH3:SAI2_MCK_B" : 10, + "PH4:EVENT-OUT" : 15, + "PH4:I2C2_SCL" : 4, + "PH4:LCD_G4" : 14, + "PH4:LCD_G5" : 9, + "PH4:OTG_HS_ULPI_NXT" : 10, + "PH5:EVENT-OUT" : 15, + "PH5:FMC_SDNWE" : 12, + "PH5:I2C2_SDA" : 4, + "PH5:SPI5_NSS" : 5, + "PH6:DCMI_D8" : 13, + "PH6:ETH_MII_RXD2" : 11, + "PH6:EVENT-OUT" : 15, + "PH6:FMC_SDNE1" : 12, + "PH6:I2C2_SMBA" : 4, + "PH6:SPI5_SCK" : 5, + "PH6:TIM12_CH1" : 2, + "PH7:DCMI_D9" : 13, + "PH7:ETH_MII_RXD3" : 11, + "PH7:EVENT-OUT" : 15, + "PH7:FMC_SDCKE1" : 12, + "PH7:I2C3_SCL" : 4, + "PH7:SPI5_MISO" : 5, + "PH8:DCMI_HSYNC" : 13, + "PH8:EVENT-OUT" : 15, + "PH8:FMC_D16" : 12, + "PH8:I2C3_SDA" : 4, + "PH8:LCD_R2" : 14, + "PH8:TIM5_ETR" : 2, + "PH9:DCMI_D0" : 13, + "PH9:EVENT-OUT" : 15, + "PH9:FMC_D17" : 12, + "PH9:I2C3_SMBA" : 4, + "PH9:LCD_R3" : 14, + "PH9:TIM12_CH2" : 2, + "PH10:DCMI_D1" : 13, + "PH10:EVENT-OUT" : 15, + "PH10:FMC_D18" : 12, + "PH10:I2C4_SMBA" : 4, + "PH10:LCD_R4" : 14, + "PH10:TIM5_CH1" : 2, + "PH11:DCMI_D2" : 13, + "PH11:EVENT-OUT" : 15, + "PH11:FMC_D19" : 12, + "PH11:I2C4_SCL" : 4, + "PH11:LCD_R5" : 14, + "PH11:TIM5_CH2" : 2, + "PH12:DCMI_D3" : 13, + "PH12:EVENT-OUT" : 15, + "PH12:FMC_D20" : 12, + "PH12:I2C4_SDA" : 4, + "PH12:LCD_R6" : 14, + "PH12:TIM5_CH3" : 2, + "PH13:EVENT-OUT" : 15, + "PH13:CAN1_TX" : 9, + "PH13:FMC_D21" : 12, + "PH13:LCD_G2" : 14, + "PH13:TIM8_CH1N" : 3, + "PH13:UART4_TX" : 8, + "PH14:DCMI_D4" : 13, + "PH14:EVENT-OUT" : 15, + "PH14:CAN1_RX" : 9, + "PH14:FMC_D22" : 12, + "PH14:LCD_G3" : 14, + "PH14:TIM8_UCH2N" : 3, + "PH14:UART4_RX" : 8, + "PH15:DCMI_D11" : 13, + "PH15:EVENT-OUT" : 15, + "PH15:CAN1_TX" : 9, + "PH15:FMC_D23" : 12, + "PH15:LCD_G4" : 14, + "PH15:TIM8_CH3N" : 3, + "PI0:DCMI_D13" : 13, + "PI0:EVENT-OUT" : 15, + "PI0:CAN1_RX" : 9, + "PI0:FMC_D24" : 12, + "PI0:I2S2_WS" : 5, + "PI0:LCD_G5" : 14, + "PI0:SPI2_NSS" : 5, + "PI0:TIM5_CH4" : 2, + "PI1:DCMI_D8" : 13, + "PI1:EVENT-OUT" : 15, + "PI1:FMC_D25" : 12, + "PI1:I2S2_CK" : 5, + "PI1:LCD_G6" : 14, + "PI1:SPI2_SCK" : 5, + "PI1:TIM8_BKIN2" : 3, + "PI1:TIM8_BKIN2_COMP12" : 11, + "PI2:DCMI_D9" : 13, + "PI2:EVENT-OUT" : 15, + "PI2:FMC_D26" : 12, + "PI2:I2S2_SDI" : 5, + "PI2:LCD_G7" : 14, + "PI2:SPI2_MISO" : 5, + "PI2:TIM8_CH4" : 3, + "PI3:DCMI_D10" : 13, + "PI3:EVENT-OUT" : 15, + "PI3:FMC_D27" : 12, + "PI3:I2S2_SDO" : 5, + "PI3:SPI2_MOSI" : 5, + "PI3:TIM8_ETR" : 3, + "PI4:DCMI_D5" : 13, + "PI4:EVENT-OUT" : 15, + "PI4:FMC_NBL2" : 12, + "PI4:LCD_B4" : 14, + "PI4:SAI2_MCK_A" : 10, + "PI4:TIM8_BKIN" : 3, + "PI4:TIM8_BKIN_COMP12" : 11, + "PI5:DCMI_VSYNC" : 13, + "PI5:EVENT-OUT" : 15, + "PI5:FMC_NBL3" : 12, + "PI5:LCD_B5" : 14, + "PI5:SAI2_SCK_A" : 10, + "PI5:TIM8_CH1" : 3, + "PI6:DCMI_D6" : 13, + "PI6:EVENT-OUT" : 15, + "PI6:FMC_D28" : 12, + "PI6:LCD_B6" : 14, + "PI6:SAI2_SD_A" : 10, + "PI6:TIM8_CH2" : 3, + "PI7:DCMI_D7" : 13, + "PI7:EVENT-OUT" : 15, + "PI7:FMC_D29" : 12, + "PI7:LCD_B7" : 14, + "PI7:SAI2_FS_A" : 10, + "PI7:TIM8_CH3" : 3, + "PI8:EVENT-OUT" : 15, + "PI9:EVENT-OUT" : 15, + "PI9:CAN1_RX" : 9, + "PI9:FMC_D30" : 12, + "PI9:LCD_VSYNC" : 14, + "PI9:UART4_RX" : 8, + "PI10:ETH_MII_RX_ER" : 11, + "PI10:EVENT-OUT" : 15, + "PI10:CAN1_RX" : 9, + "PI10:FMC_D31" : 12, + "PI10:LCD_HSYNC" : 14, + "PI11:EVENT-OUT" : 15, + "PI11:LCD_G6" : 9, + "PI11:OTG_HS_ULPI_DIR" : 10, + "PI12:EVENT-OUT" : 15, + "PI12:LCD_HSYNC" : 14, + "PI13:EVENT-OUT" : 15, + "PI13:LCD_VSYNC" : 14, + "PI14:EVENT-OUT" : 15, + "PI14:LCD_CLK" : 14, + "PI15:EVENT-OUT" : 15, + "PI15:LCD_G2" : 9, + "PI15:LCD_R0" : 14, + "PJ0:EVENT-OUT" : 15, + "PJ0:LCD_R1" : 14, + "PJ0:LCD_R7" : 9, + "PJ1:EVENT-OUT" : 15, + "PJ1:LCD_R2" : 14, + "PJ2:EVENT-OUT" : 15, + "PJ2:LCD_R3" : 14, + "PJ3:EVENT-OUT" : 15, + "PJ3:LCD_R4" : 14, + "PJ4:EVENT-OUT" : 15, + "PJ4:LCD_R5" : 14, + "PJ5:EVENT-OUT" : 15, + "PJ5:LCD_R6" : 14, + "PJ6:EVENT-OUT" : 15, + "PJ6:LCD_R7" : 14, + "PJ6:TIM8_CH2" : 3, + "PJ7:EVENT-OUT" : 15, + "PJ7:LCD_G0" : 14, + "PJ7:TIM8_CH2N" : 3, + "PJ7:TRGIN" : 0, + "PJ8:EVENT-OUT" : 15, + "PJ8:LCD_G1" : 14, + "PJ8:TIM1_CH3N" : 1, + "PJ8:TIM8_CH1" : 3, + "PJ8:UART8_TX" : 8, + "PJ9:EVENT-OUT" : 15, + "PJ9:LCD_G2" : 14, + "PJ9:TIM1_CH3" : 1, + "PJ9:TIM8_CH1N" : 3, + "PJ9:UART8_RX" : 8, + "PJ10:EVENT-OUT" : 15, + "PJ10:LCD_G3" : 14, + "PJ10:SPI5_MOSI" : 5, + "PJ10:TIM1_CH2N" : 1, + "PJ10:TIM8_CH2" : 3, + "PJ11:EVENT-OUT" : 15, + "PJ11:LCD_G4" : 14, + "PJ11:SPI5_MISO" : 5, + "PJ11:TIM1_CH2" : 1, + "PJ11:TIM8_CH2N" : 3, + "PJ12:EVENT-OUT" : 15, + "PJ12:LCD_B0" : 14, + "PJ12:LCD_G3" : 9, + "PJ12:TRGOUT" : 0, + "PJ13:EVENT-OUT" : 15, + "PJ13:LCD_B1" : 14, + "PJ13:LCD_B4" : 9, + "PJ14:EVENT-OUT" : 15, + "PJ14:LCD_B2" : 14, + "PJ15:EVENT-OUT" : 15, + "PJ15:LCD_B3" : 14, + "PK0:EVENT-OUT" : 15, + "PK0:LCD_G5" : 14, + "PK0:SPI5_SCK" : 5, + "PK0:TIM1_CH1N" : 1, + "PK0:TIM8_CH3" : 3, + "PK1:EVENT-OUT" : 15, + "PK1:LCD_G6" : 14, + "PK1:SPI5_NSS" : 5, + "PK1:TIM1_CH1" : 1, + "PK1:TIM8_CH3N" : 3, + "PK2:EVENT-OUT" : 15, + "PK2:LCD_G7" : 14, + "PK2:TIM1_BKIN" : 1, + "PK2:TIM1_BKIN_COMP12" : 11, + "PK2:TIM8_BKIN" : 3, + "PK2:TIM8_BKIN_COMP12" : 10, + "PK3:EVENT-OUT" : 15, + "PK3:LCD_B4" : 14, + "PK4:EVENT-OUT" : 15, + "PK4:LCD_B5" : 14, + "PK5:EVENT-OUT" : 15, + "PK5:LCD_B6" : 14, + "PK6:EVENT-OUT" : 15, + "PK6:LCD_B7" : 14, + "PK7:EVENT-OUT" : 15, + "PK7:LCD_DE" : 14, +} + +ADC1_map = { + # format is PIN : ADC1_CHAN + "PF11" : 2, + "PA6" : 3, + "PC4" : 4, + "PB1" : 5, + "PF12" : 6, + "PA7" : 7, + "PC5" : 8, + "PB0" : 9, + "PC0" : 10, + "PC1" : 11, + "PC2" : 12, + "PC3" : 13, + "PA2" : 14, + "PA3" : 15, + "PA0" : 16, + "PA1" : 17, + "PA4" : 18, + "PA5" : 19, +}